From: Jiri Slaby <jirislaby@gmail.com>
To: Alan Stern <stern@rowland.harvard.edu>
Cc: Greg KH <greg@kroah.com>, Jiri Slaby <jirislaby@gmail.com>,
"Rafael J. Wysocki" <rjw@sisk.pl>,
Andrew Morton <akpm@linux-foundation.org>,
linux-kernel@vger.kernel.org,
Linux-pm mailing list <linux-pm@lists.linux-foundation.org>
Subject: Re: broken suspend [Was: 2.6.24-rc2-mm1]
Date: Sat, 17 Nov 2007 16:08:15 +0100 [thread overview]
Message-ID: <473F03DF.4020306@gmail.com> (raw)
In-Reply-To: <Pine.LNX.4.44L0.0711161058170.2738-100000@iolanthe.rowland.org>
On 11/16/2007 05:10 PM, Alan Stern wrote:
> On Thu, 15 Nov 2007, Greg KH wrote:
>
>>> The offending -mm patch is
>>> gregkh-driver-pm-acquire-device-locks-prior-to-suspending.patch
>>>
>>> 2.6.24-rc2-mm1 minus it works just fine; PROVE_LOCKING shows nothing new when
>>> the patch is applied.
>> Thanks for tracking this down. Alan, any thoughts?
>
> It's a driver problem somewhere. Probably not one of the most common
> drivers because I don't see the same problem here (but then I'm not
> testing -mm).
>
> The thing to do is figure out which driver is causing the problem.
> Jiri, try enabling CONFIG_DEBUG_DRIVER.
Sadly no output.
> If there's also a config
> option to prevent the console from being suspended, set it as well.
no_suspend_console kernel parameter has no effect (why?).
> Then you should be able to tell which driver is making trouble.
I think no unusual hardware inside:
00:00.0 Host bridge: Intel Corporation 82G33/G31/P35 Express DRAM Controller
(rev 02)
Subsystem: Intel Corporation 82G33/G31/P35 Express DRAM Controller
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ >SERR- <PERR-
Latency: 0
Capabilities: [e0] Vendor Specific Information
00: 86 80 c0 29 06 00 90 20 02 00 00 06 00 00 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 86 80 c0 29
30: 00 00 00 00 e0 00 00 00 00 00 00 00 00 00 00 00
00:02.0 VGA compatible controller: Intel Corporation 82G33/G31 Express
Integrated Graphics Controller (rev 02) (prog-if 00 [VGA])
Subsystem: Intel Corporation 82G33/G31 Express Integrated Graphics
Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: Memory at ffa80000 (32-bit, non-prefetchable) [size=512K]
Region 1: I/O ports at ec00 [size=8]
Region 2: Memory at d0000000 (32-bit, prefetchable) [size=256M]
Region 3: Memory at ff900000 (32-bit, non-prefetchable) [size=1M]
Capabilities: [90] Message Signalled Interrupts: Mask- 64bit- Queue=0/0
Enable-
Address: 00000000 Data: 0000
Capabilities: [d0] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 86 80 c2 29 07 00 90 00 02 00 00 03 00 00 00 00
10: 00 00 a8 ff 01 ec 00 00 08 00 00 d0 00 00 90 ff
20: 00 00 00 00 00 00 00 00 00 00 00 00 86 80 c2 29
30: 00 00 00 00 90 00 00 00 00 00 00 00 0a 01 00 00
00:03.0 Communication controller: Intel Corporation 82G33/G31/P35 Express MEI
Controller (rev 02)
Subsystem: Intel Corporation 82G33/G31/P35 Express MEI Controller
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 10
Region 0: Memory at ffa7bc00 (64-bit, non-prefetchable) [size=16]
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [8c] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0
Enable-
Address: 0000000000000000 Data: 0000
00: 86 80 c4 29 06 00 10 00 02 00 80 07 00 00 80 00
10: 04 bc a7 ff 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 86 80 c4 29
30: 00 00 00 00 50 00 00 00 00 00 00 00 0a 01 00 00
00:03.2 IDE interface: Intel Corporation 82G33/G31/P35 Express PT IDER
Controller (rev 02) (prog-if 85 [Master SecO PriO])
Subsystem: Intel Corporation 82G33/G31/P35 Express PT IDER Controller
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin C routed to IRQ 12
Region 0: I/O ports at e880 [size=8]
Region 1: I/O ports at e800 [size=4]
Region 2: I/O ports at e480 [size=8]
Region 3: I/O ports at e400 [size=4]
Region 4: I/O ports at e080 [size=16]
Capabilities: [c8] Power Management version 3
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [d0] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0
Enable-
Address: 0000000000000000 Data: 0000
00: 86 80 c6 29 05 00 b0 00 02 85 01 01 00 00 00 00
10: 81 e8 00 00 01 e8 00 00 81 e4 00 00 01 e4 00 00
20: 81 e0 00 00 00 00 00 00 00 00 00 00 86 80 c6 29
30: 00 00 00 00 c8 00 00 00 00 00 00 00 0c 03 00 00
00:03.3 Serial controller: Intel Corporation 82G33/G31/P35 Express Serial KT
Controller (rev 02) (prog-if 02 [16550])
Subsystem: Intel Corporation 82G33/G31/P35 Express Serial KT Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 17
Region 0: I/O ports at e000 [size=8]
Region 1: Memory at ffa7a000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [c8] Power Management version 3
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [d0] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0
Enable-
Address: 0000000000000000 Data: 0000
00: 86 80 c7 29 07 00 b0 00 02 02 00 07 00 00 00 00
10: 01 e0 00 00 00 a0 a7 ff 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 86 80 c7 29
30: 00 00 00 00 c8 00 00 00 00 00 00 00 05 02 00 00
00:19.0 Ethernet controller: Intel Corporation 82566DM-2 Gigabit Network
Connection (rev 02)
Subsystem: Intel Corporation Unknown device 0000
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 318
Region 0: Memory at ffa40000 (32-bit, non-prefetchable) [size=128K]
Region 1: Memory at ffa79000 (32-bit, non-prefetchable) [size=4K]
Region 2: I/O ports at dc00 [size=32]
Capabilities: [c8] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [d0] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0
Enable+
Address: 00000000fee0300c Data: 4191
Capabilities: [e0] Vendor Specific Information
00: 86 80 bd 10 07 04 10 00 02 00 00 02 00 00 00 00
10: 00 00 a4 ff 00 90 a7 ff 01 dc 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 86 80 00 00
30: 00 00 00 00 c8 00 00 00 00 00 00 00 0f 01 00 00
00:1a.0 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI
Controller #4 (rev 02) (prog-if 00 [UHCI])
Subsystem: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #4
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 4: I/O ports at d880 [size=32]
Capabilities: [50] Vendor Specific Information
00: 86 80 37 29 05 00 90 02 02 00 03 0c 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 81 d8 00 00 00 00 00 00 00 00 00 00 86 80 37 29
30: 00 00 00 00 50 00 00 00 00 00 00 00 0a 01 00 00
00:1a.1 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI
Controller #5 (rev 02) (prog-if 00 [UHCI])
Subsystem: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #5
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 21
Region 4: I/O ports at d800 [size=32]
Capabilities: [50] Vendor Specific Information
00: 86 80 38 29 05 00 90 02 02 00 03 0c 00 00 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 01 d8 00 00 00 00 00 00 00 00 00 00 86 80 38 29
30: 00 00 00 00 50 00 00 00 00 00 00 00 0e 02 00 00
00:1a.2 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI
Controller #6 (rev 02) (prog-if 00 [UHCI])
Subsystem: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #6
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at d480 [size=32]
Capabilities: [50] Vendor Specific Information
00: 86 80 39 29 05 00 90 02 02 00 03 0c 00 00 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 81 d4 00 00 00 00 00 00 00 00 00 00 86 80 39 29
30: 00 00 00 00 50 00 00 00 00 00 00 00 0c 03 00 00
00:1a.7 USB Controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI
Controller #2 (rev 02) (prog-if 20 [EHCI])
Subsystem: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #2
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin D routed to IRQ 19
Region 0: Memory at ffa7b400 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port
Capabilities: [98] Vendor Specific Information
00: 86 80 3c 29 06 00 90 02 02 20 03 0c 00 00 00 00
10: 00 b4 a7 ff 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 86 80 3c 29
30: 00 00 00 00 50 00 00 00 00 00 00 00 03 04 00 00
00:1b.0 Audio device: Intel Corporation 82801I (ICH9 Family) HD Audio Controller
(rev 02)
Subsystem: Intel Corporation 82801I (ICH9 Family) HD Audio Controller
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 22
Region 0: Memory at ffa70000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [60] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0
Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [70] Express Unknown type IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed unknown, Width x0, ASPM unknown, Port 0
Link: Latency L0s <64ns, L1 <1us
Link: ASPM Disabled CommClk- ExtSynch-
Link: Speed unknown, Width x0
Capabilities: [100] Virtual Channel
Capabilities: [130] Unknown (5)
00: 86 80 3e 29 06 00 10 00 02 00 03 04 08 00 00 00
10: 04 00 a7 ff 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 86 80 3e 29
30: 00 00 00 00 50 00 00 00 00 00 00 00 07 01 00 00
00:1d.0 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI
Controller #1 (rev 02) (prog-if 00 [UHCI])
Subsystem: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #1
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 4: I/O ports at d400 [size=32]
Capabilities: [50] Vendor Specific Information
00: 86 80 34 29 05 00 90 02 02 00 03 0c 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 01 d4 00 00 00 00 00 00 00 00 00 00 86 80 34 29
30: 00 00 00 00 50 00 00 00 00 00 00 00 0a 01 00 00
00:1d.1 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI
Controller #2 (rev 02) (prog-if 00 [UHCI])
Subsystem: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #2
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 4: I/O ports at d080 [size=32]
Capabilities: [50] Vendor Specific Information
00: 86 80 35 29 05 00 90 02 02 00 03 0c 00 00 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 81 d0 00 00 00 00 00 00 00 00 00 00 86 80 35 29
30: 00 00 00 00 50 00 00 00 00 00 00 00 03 02 00 00
00:1d.2 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI
Controller #3 (rev 02) (prog-if 00 [UHCI])
Subsystem: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin D routed to IRQ 16
Region 4: I/O ports at d000 [size=32]
Capabilities: [50] Vendor Specific Information
00: 86 80 36 29 05 00 90 02 02 00 03 0c 00 00 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 01 d0 00 00 00 00 00 00 00 00 00 00 86 80 36 29
30: 00 00 00 00 50 00 00 00 00 00 00 00 0a 04 00 00
00:1d.7 USB Controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI
Controller #1 (rev 02) (prog-if 20 [EHCI])
Subsystem: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #1
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 0: Memory at ffa7b000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port
Capabilities: [98] Vendor Specific Information
00: 86 80 3a 29 06 00 90 02 02 20 03 0c 00 00 00 00
10: 00 b0 a7 ff 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 86 80 3a 29
30: 00 00 00 00 50 00 00 00 00 00 00 00 0a 01 00 00
00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev 92) (prog-if 01
[Subtractive decode])
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
Memory behind bridge: ff600000-ff6fffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [50] Subsystem: Intel Corporation 82801 PCI Bridge
00: 86 80 4e 24 06 01 10 00 92 01 04 06 00 00 01 00
10: 00 00 00 00 00 00 00 00 00 01 01 20 f0 00 80 22
20: 60 ff 60 ff f1 ff 01 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 50 00 00 00 00 00 00 00 ff 00 02 00
00:1f.0 ISA bridge: Intel Corporation Unknown device 2910 (rev 02)
Subsystem: Intel Corporation Unknown device 2910
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [e0] Vendor Specific Information
00: 86 80 10 29 07 00 10 02 02 00 01 06 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 86 80 10 29
30: 00 00 00 00 e0 00 00 00 00 00 00 00 00 00 00 00
00:1f.2 SATA controller: Intel Corporation 82801IR/IO/IH (ICH9R/DO/DH) 6 port
SATA AHCI Controller (rev 02) (prog-if 01 [AHCI 1.0])
Subsystem: Intel Corporation 82801IR/IO/IH (ICH9R/DO/DH) 6 port SATA
AHCI Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 319
Region 0: I/O ports at cc00 [size=8]
Region 1: I/O ports at c880 [size=4]
Region 2: I/O ports at c800 [size=8]
Region 3: I/O ports at c480 [size=4]
Region 4: I/O ports at c400 [size=32]
Region 5: Memory at ffa78800 (32-bit, non-prefetchable) [size=2K]
Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/4
Enable+
Address: fee0300c Data: 4169
Capabilities: [70] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [a8] #12 [0010]
Capabilities: [b0] Vendor Specific Information
00: 86 80 22 29 07 04 b0 02 02 01 06 01 00 00 00 00
10: 01 cc 00 00 81 c8 00 00 01 c8 00 00 81 c4 00 00
20: 01 c4 00 00 00 88 a7 ff 00 00 00 00 86 80 22 29
30: 00 00 00 00 80 00 00 00 00 00 00 00 03 02 00 00
00:1f.3 SMBus: Intel Corporation 82801I (ICH9 Family) SMBus Controller (rev 02)
Subsystem: Intel Corporation 82801I (ICH9 Family) SMBus Controller
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin C routed to IRQ 18
Region 0: Memory at ffa7b800 (64-bit, non-prefetchable) [size=256]
Region 4: I/O ports at 0400 [size=32]
00: 86 80 30 29 03 00 80 02 02 00 05 0c 00 00 00 00
10: 04 b8 a7 ff 00 00 00 00 00 00 00 00 00 00 00 00
20: 01 04 00 00 00 00 00 00 00 00 00 00 86 80 30 29
30: 00 00 00 00 00 00 00 00 00 00 00 00 03 03 00 00
00:1f.5 IDE interface: Intel Corporation 82801I (ICH9 Family) 2 port SATA IDE
Controller (rev 02) (prog-if 85 [Master SecO PriO])
Subsystem: Intel Corporation 82801I (ICH9 Family) 2 port SATA IDE Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 0: I/O ports at c000 [size=8]
Region 1: I/O ports at bc00 [size=4]
Region 2: I/O ports at b880 [size=8]
Region 3: I/O ports at b800 [size=4]
Region 4: I/O ports at b480 [size=16]
Region 5: I/O ports at b400 [size=16]
Capabilities: [70] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [b0] Vendor Specific Information
00: 86 80 26 29 07 00 b0 02 02 85 01 01 00 00 00 00
10: 01 c0 00 00 01 bc 00 00 81 b8 00 00 01 b8 00 00
20: 81 b4 00 00 01 b4 00 00 00 00 00 00 86 80 26 29
30: 00 00 00 00 70 00 00 00 00 00 00 00 03 02 00 00
00:1f.6 Signal processing controller: Intel Corporation 82801I (ICH9 Family)
Thermal Subsystem (rev 02)
Subsystem: Intel Corporation 82801I (ICH9 Family) Thermal Subsystem
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Interrupt: pin C routed to IRQ 12
Region 0: Memory at ffa6f000 (64-bit, non-prefetchable) [size=4K]
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 86 80 32 29 02 00 10 00 02 00 80 11 00 00 00 00
10: 04 f0 a6 ff 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 86 80 32 29
30: 00 00 00 00 50 00 00 00 00 00 00 00 0c 03 00 00
01:00.0 Ethernet controller: Atheros Communications, Inc. AR5212 802.11abg NIC
(rev 01)
Subsystem: Wistron NeWeb Corp. CM9 Wireless a/b/g MiniPCI Adapter
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 168 (2500ns min, 7000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 21
Region 0: Memory at ff6f0000 (32-bit, non-prefetchable) [size=64K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
00: 8c 16 13 00 16 00 90 02 01 00 00 02 08 a8 00 00
10: 00 00 6f ff 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 01 50 00 00 5f 18 12 10
30: 00 00 00 00 44 00 00 00 00 00 00 00 0e 01 0a 1c
Plugged usb devices:
Bus 004 Device 007: ID 045e:00f0 Microsoft Corp.
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 8
idVendor 0x045e Microsoft Corp.
idProduct 0x00f0
bcdDevice 1.01
iManufacturer 1 Microsoft Corporation
iProduct 2 Microsoft � Laser Mouse 6000
iSerial 0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 34
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xa0
Remote Wakeup
MaxPower 100mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 3 Human Interface Devices
bInterfaceSubClass 1 Boot Interface Subclass
bInterfaceProtocol 2 Mouse
iInterface 0
HID Device Descriptor:
bLength 9
bDescriptorType 33
bcdHID 1.11
bCountryCode 33 US
bNumDescriptors 1
bDescriptorType 34 Report
wDescriptorLength 59
Report Descriptors:
** UNAVAILABLE **
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0004 1x 4 bytes
bInterval 10
Bus 004 Device 006: ID 0458:004c KYE Systems Corp. (Mouse Systems) Slimstar Pro
Keyboard
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 8
idVendor 0x0458 KYE Systems Corp. (Mouse Systems)
idProduct 0x004c Slimstar Pro Keyboard
bcdDevice 1.01
iManufacturer 1 ABBHOME
iProduct 2 USB Keyboard
iSerial 0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 59
bNumInterfaces 2
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 50mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 3 Human Interface Devices
bInterfaceSubClass 1 Boot Interface Subclass
bInterfaceProtocol 1 Keyboard
iInterface 0
HID Device Descriptor:
bLength 9
bDescriptorType 33
bcdHID 1.10
bCountryCode 0 Not supported
bNumDescriptors 1
bDescriptorType 34 Report
wDescriptorLength 65
Report Descriptors:
** UNAVAILABLE **
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0008 1x 8 bytes
bInterval 10
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 1
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 3 Human Interface Devices
bInterfaceSubClass 1 Boot Interface Subclass
bInterfaceProtocol 2 Mouse
iInterface 0
HID Device Descriptor:
bLength 9
bDescriptorType 33
bcdHID 1.10
bCountryCode 0 Not supported
bNumDescriptors 1
bDescriptorType 34 Report
wDescriptorLength 104
Report Descriptors:
** UNAVAILABLE **
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x82 EP 2 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0008 1x 8 bytes
bInterval 10
Bus 004 Device 005: ID 04b4:2050 Cypress Semiconductor Corp.
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 0 Full speed (or root) hub
bMaxPacketSize0 8
idVendor 0x04b4 Cypress Semiconductor Corp.
idProduct 0x2050
bcdDevice 0.01
iManufacturer 1 Bella Corporation
iProduct 2 GBella Corporation DV Keyboard
iSerial 0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 100mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0 Full speed (or root) hub
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0001 1x 1 bytes
bInterval 255
Hub Descriptor:
bLength 9
bDescriptorType 41
nNbrPorts 3
wHubCharacteristic 0x000d
Per-port power switching
Compound device
Per-port overcurrent protection
bPwrOn2PwrGood 50 * 2 milli seconds
bHubContrCurrent 25 milli Ampere
DeviceRemovable 0x00
PortPwrCtrlMask 0x60
Hub Port Status:
Port 1: 0000.0103 power enable connect
Port 2: 0000.0303 lowspeed power enable connect
Port 3: 0000.0100 power
regards,
--
Jiri Slaby (jirislaby@gmail.com)
Faculty of Informatics, Masaryk University
next prev parent reply other threads:[~2007-11-17 15:08 UTC|newest]
Thread overview: 190+ messages / expand[flat|nested] mbox.gz Atom feed top
2007-11-14 1:59 2.6.24-rc2-mm1 Andrew Morton
2007-11-14 3:12 ` 2.6.24-rc2-mm1 Gabriel C
2007-11-14 3:49 ` 2.6.24-rc2-mm1 Greg KH
2007-11-14 4:39 ` 2.6.24-rc2-mm1 Matthew Dharm
2007-11-14 5:33 ` 2.6.24-rc2-mm1 Gabriel C
2007-11-14 8:23 ` 2.6.24-rc2-mm1 Matthew Dharm
2007-11-14 9:23 ` 2.6.24-rc2-mm1 Gabriel C
2007-11-15 17:15 ` 2.6.24-rc2-mm1 Matthew Dharm
2007-11-15 18:14 ` 2.6.24-rc2-mm1 Boaz Harrosh
2007-11-15 21:42 ` 2.6.24-rc2-mm1 Gabriel C
2007-11-14 4:18 ` 2.6.24-rc2-mm1 Gabriel C
2007-11-14 20:29 ` 2.6.24-rc2-mm1 mark gross
2007-11-14 20:40 ` 2.6.24-rc2-mm1 Andrew Morton
2007-11-15 17:22 ` 2.6.24-rc2-mm1 mark gross
2007-11-15 20:05 ` 2.6.24-rc2-mm1 Andrew Morton
2007-11-15 17:23 ` 2.6.24-rc2-mm1 mark gross
2007-11-15 19:19 ` 2.6.24-rc2-mm1 mark gross
2007-11-15 21:40 ` 2.6.24-rc2-mm1 Gabriel C
2007-11-15 22:56 ` 2.6.24-rc2-mm1 mark gross
2007-11-15 23:01 ` [PATCH] pm-qos-remove-locks-around-blocking-notifier.patch ... was 2.6.24-rc2-mm1 mark gross
2007-11-14 3:40 ` [PATCH] Fix build failure when CONFIG_INFINIBAND_IPOIB_CM is not defined Tony Breeds
2007-11-15 14:49 ` Mel Gorman
2007-11-14 3:41 ` 2.6.24-rc2-mm1 Gabriel C
2007-11-14 4:55 ` 2.6.24-rc2-mm1 Andrew Morton
2007-11-14 5:10 ` 2.6.24-rc2-mm1 Ulrich Drepper
2007-11-14 5:27 ` 2.6.24-rc2-mm1 Gabriel C
2007-11-14 5:45 ` 2.6.24-rc2-mm1 Zan Lynx
2007-11-14 6:18 ` 2.6.24-rc2-mm1 Dave Young
2007-11-14 6:38 ` 2.6.24-rc2-mm1 Andrew Morton
2007-11-14 6:47 ` 2.6.24-rc2-mm1 Dave Young
2007-11-14 8:41 ` 2.6.24-rc2-mm1 Andrew Morton
2007-11-14 9:32 ` 2.6.24-rc2-mm1 Andrew Morton
2007-11-14 9:36 ` 2.6.24-rc2-mm1 Dave Young
2007-11-14 16:59 ` 2.6.24-rc2-mm1 Greg KH
2007-11-14 18:38 ` 2.6.24-rc2-mm1 Kay Sievers
2007-11-14 19:19 ` 2.6.24-rc2-mm1 Jiri Kosina
2007-11-14 21:27 ` 2.6.24-rc2-mm1 Kay Sievers
2007-11-15 1:01 ` 2.6.24-rc2-mm1 Dave Young
2007-11-15 2:38 ` 2.6.24-rc2-mm1 Kay Sievers
2007-11-15 3:11 ` 2.6.24-rc2-mm1 Dave Young
2007-11-15 8:14 ` 2.6.24-rc2-mm1 Dave Young
2007-11-15 8:51 ` 2.6.24-rc2-mm1 Kay Sievers
2007-11-15 17:06 ` 2.6.24-rc2-mm1 Greg KH
2007-11-15 17:16 ` 2.6.24-rc2-mm1 Kay Sievers
2007-11-15 18:59 ` 2.6.24-rc2-mm1 Greg KH
2007-11-14 6:32 ` [PATCH] [2.6.24-rc2-mm1] Fix dependencies for FSL_DMA Olof Johansson
2007-11-14 8:56 ` 2.6.24-rc2-mm1 -- mkfs failing on variety of fs types Andy Whitcroft
2007-11-14 10:28 ` Andrew Morton
2007-11-14 10:46 ` Dmitry Monakhov
2007-11-14 14:40 ` 2.6.24-rc2-mm1 Jiri Kosina
2007-11-14 14:59 ` 2.6.24-rc2-mm1 Matthias Urlichs
2007-11-14 15:04 ` 2.6.24-rc2-mm1 Jiri Kosina
2007-11-14 15:43 ` 2.6.24-rc2-mm1 Matthias Urlichs
2007-11-14 15:49 ` 2.6.24-rc2-mm1 Jiri Kosina
2007-11-14 16:29 ` 2.6.24-rc2-mm1 Jiri Kosina
2007-11-14 16:39 ` 2.6.24-rc2-mm1 Andrew Morton
2007-11-14 16:40 ` 2.6.24-rc2-mm1 Jiri Kosina
2007-11-14 17:02 ` 2.6.24-rc2-mm1 Jiri Kosina
2007-11-14 17:38 ` 2.6.24-rc2-mm1 Jiri Kosina
2007-11-14 18:19 ` 2.6.24-rc2-mm1 Greg KH
2007-11-15 19:23 ` 2.6.24-rc2-mm1 Greg KH
2007-11-15 21:41 ` 2.6.24-rc2-mm1 Jiri Kosina
2007-11-15 21:53 ` 2.6.24-rc2-mm1 Andrew Morton
2007-11-15 22:04 ` 2.6.24-rc2-mm1 Jiri Kosina
2007-11-16 0:39 ` 2.6.24-rc2-mm1 Dave Young
2007-11-16 0:49 ` 2.6.24-rc2-mm1 Greg KH
2007-11-16 0:55 ` 2.6.24-rc2-mm1 Dave Young
2007-11-14 19:16 ` 2.6.24-rc2-mm1 Torsten Kaiser
2007-11-14 20:29 ` 2.6.24-rc2-mm1 Andrew Morton
2007-11-14 20:55 ` 2.6.24-rc2-mm1 Torsten Kaiser
2007-11-14 22:48 ` 2.6.24-rc2-mm1 Torsten Kaiser
2007-11-15 17:36 ` 2.6.24-rc2-mm1 Jan Blunck
2007-11-15 18:36 ` 2.6.24-rc2-mm1 Torsten Kaiser
2007-11-15 21:24 ` 2.6.24-rc2-mm1 Torsten Kaiser
2007-11-15 21:34 ` 2.6.24-rc2-mm1 Andrew Morton
2007-11-16 5:29 ` 2.6.24-rc2-mm1 Torsten Kaiser
2007-11-16 14:03 ` 2.6.24-rc2-mm1 Jan Blunck
2007-11-16 20:11 ` 2.6.24-rc2-mm1 Torsten Kaiser
2007-11-14 20:24 ` broken suspend [Was: 2.6.24-rc2-mm1] Jiri Slaby
2007-11-14 20:36 ` Andrew Morton
2007-11-14 21:48 ` Rafael J. Wysocki
2007-11-15 23:59 ` Jiri Slaby
2007-11-15 23:59 ` Jiri Slaby
2007-11-16 0:38 ` Greg KH
2007-11-16 0:38 ` Greg KH
2007-11-16 16:10 ` Alan Stern
2007-11-16 16:10 ` Alan Stern
2007-11-17 15:08 ` Jiri Slaby [this message]
2007-11-17 15:12 ` Jiri Slaby
2007-11-17 15:12 ` Jiri Slaby
2007-11-17 16:13 ` Alan Stern
2007-11-17 16:13 ` Alan Stern
2007-11-17 20:37 ` Rafael J. Wysocki
2007-11-17 20:37 ` Rafael J. Wysocki
2007-11-17 21:58 ` Alan Stern
2007-11-17 21:58 ` Alan Stern
2007-11-18 12:42 ` Jiri Slaby
2007-11-18 12:42 ` Jiri Slaby
2007-11-18 13:06 ` Jiri Slaby
2007-11-18 13:42 ` Rafael J. Wysocki
2007-11-18 13:42 ` Rafael J. Wysocki
2007-11-18 13:53 ` Jiri Slaby
2007-11-18 13:53 ` Jiri Slaby
2007-11-18 15:03 ` Rafael J. Wysocki
2007-11-18 14:49 ` Jiri Slaby
2007-11-18 14:49 ` Jiri Slaby
2007-11-18 15:23 ` Rafał J. Wysocki
2007-11-18 15:15 ` Jiri Slaby
2007-11-18 15:15 ` Jiri Slaby
2007-11-18 17:07 ` Alan Stern
2007-11-18 17:07 ` Alan Stern
2007-11-18 19:09 ` Jiri Slaby
2007-11-18 19:09 ` Jiri Slaby
2007-11-18 22:27 ` Jiri Slaby
2007-11-18 22:27 ` Jiri Slaby
2007-11-18 22:27 ` [lm-sensors] " Jiri Slaby
2007-11-19 3:04 ` Alan Stern
2007-11-19 3:04 ` Alan Stern
2007-11-19 20:01 ` Rudolf Marek
2007-11-19 20:01 ` [lm-sensors] " Rudolf Marek
2007-11-19 20:01 ` Rudolf Marek
2007-11-19 20:27 ` Alan Stern
2007-11-19 21:53 ` [lm-sensors] " Rafael J. Wysocki
2007-11-19 21:53 ` Rafael J. Wysocki
2007-11-19 21:53 ` Rafael J. Wysocki
2007-11-19 3:04 ` Alan Stern
2007-11-19 20:27 ` [lm-sensors] " Alan Stern
2007-11-19 20:27 ` Alan Stern
2007-11-20 13:15 ` [lm-sensors] " Mark M. Hoffman
2007-11-20 13:15 ` Mark M. Hoffman
2007-11-20 23:46 ` Rafael J. Wysocki
2007-11-21 0:00 ` Rafael J. Wysocki
2007-11-21 15:54 ` Alan Stern
2007-11-26 8:57 ` Jiri Slaby
2007-11-26 8:57 ` Jiri Slaby
2007-11-26 8:57 ` Jiri Slaby
2007-11-21 0:00 ` Rafael J. Wysocki
2007-11-20 13:15 ` Mark M. Hoffman
2007-11-21 15:54 ` Alan Stern
2007-11-21 15:54 ` Alan Stern
2007-11-21 19:19 ` Rafael J. Wysocki
2007-11-21 19:19 ` Rafael J. Wysocki
2007-11-21 19:19 ` Rafael J. Wysocki
2007-11-18 22:27 ` Rafael J. Wysocki
2007-11-18 22:27 ` Rafael J. Wysocki
2007-11-18 22:12 ` Jiri Slaby
2007-11-18 22:42 ` Rafael J. Wysocki
2007-11-18 22:42 ` Rafael J. Wysocki
2007-11-18 22:12 ` Jiri Slaby
2007-11-18 15:23 ` Rafał J. Wysocki
2007-11-18 15:03 ` Rafael J. Wysocki
2007-11-18 13:06 ` Jiri Slaby
2007-11-17 15:08 ` Jiri Slaby
2007-11-15 4:29 ` 2.6.24-rc2-mm1 (memory hotplug x86_64/vmemmap fix) KAMEZAWA Hiroyuki
2007-11-15 5:39 ` Kamalesh Babulal
2007-11-15 8:56 ` Andrew Morton
2007-11-15 9:18 ` KAMEZAWA Hiroyuki
2007-11-15 10:30 ` [PATCH][2.6.24-rc2-mm1] memory hotplug x86_64 fix [0/3] KAMEZAWA Hiroyuki
2007-11-15 10:33 ` [PATCH][2.6.24-rc2-mm1] memory hotplug x86_64 fix [1/3] memory_add_physaddr_to_nid export for acpi memhotplug.ko KAMEZAWA Hiroyuki
2007-11-15 10:35 ` [PATCH][2.6.24-rc2-mm1] memory hotplug x86_64 fix [2/3] fix section mismatch in vmammap_allock_block KAMEZAWA Hiroyuki
2007-11-16 0:53 ` Andrew Morton
2007-11-16 4:45 ` KAMEZAWA Hiroyuki
2007-11-15 10:36 ` [PATCH][2.6.24-rc2-mm1] memory hotplug x86_64 fix [3/3] fix section mismatch in init_memory_mapping KAMEZAWA Hiroyuki
2007-11-16 0:59 ` Andrew Morton
2007-11-16 5:09 ` KAMEZAWA Hiroyuki
2007-11-15 9:39 ` 2.6.24-rc2-mm1 (memory hotplug x86_64/vmemmap fix) Andy Whitcroft
2007-11-15 10:05 ` KAMEZAWA Hiroyuki
2007-11-15 10:02 ` 2.6.24-rc2-mm1 -- strange apparent network failures Andy Whitcroft
2007-11-16 0:28 ` Kevin Winchester
2007-11-16 0:44 ` Andrew Morton
2007-11-16 1:01 ` Kevin Winchester
2007-11-16 1:09 ` Andrew Morton
2007-11-17 5:16 ` Andrew Morgan
2007-11-17 12:48 ` Kevin Winchester
2007-11-17 23:52 ` Andrew Morgan
2007-11-18 0:50 ` Kevin Winchester
2007-11-18 1:17 ` Kevin Winchester
2007-11-18 1:57 ` Andrew Morgan
2007-11-18 1:23 ` Kevin Winchester
2007-11-17 13:57 ` Andy Whitcroft
2007-11-16 1:21 ` Tom
2007-11-15 10:50 ` 2.6.24-rc2-mm1 -- QLogics ISP1020 gone missing Andy Whitcroft
2007-11-15 19:25 ` 2.6.24-rc2-mm1 Greg KH
2007-11-15 20:47 ` 2.6.24-rc2-mm1 Andrew Morton
2007-11-16 0:01 ` 2.6.24-rc2-mm1 Greg KH
2007-11-15 22:25 ` 2.6.24-rc2-mm1: undefined reference to `local_apic_timer_c2_ok' Mariusz Kozlowski
2007-11-15 22:49 ` Len Brown
2007-11-15 23:35 ` Mariusz Kozlowski
2007-11-15 22:34 ` [parisc-linux] [PATCH] parisc: balance parenthesis in pte_free_kernel() Mariusz Kozlowski
2007-11-15 22:34 ` Mariusz Kozlowski
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=473F03DF.4020306@gmail.com \
--to=jirislaby@gmail.com \
--cc=akpm@linux-foundation.org \
--cc=greg@kroah.com \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-pm@lists.linux-foundation.org \
--cc=rjw@sisk.pl \
--cc=stern@rowland.harvard.edu \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.