From: Matthieu PATOU <mat@matws.net>
To: linux-wireless@vger.kernel.org
Subject: Re: BCM4312 status
Date: Sun, 25 Nov 2007 17:20:33 +0300 [thread overview]
Message-ID: <474984B1.90302@matws.net> (raw)
In-Reply-To: <47469E42.6050909@matws.net>
Matthieu PATOU a =E9crit :
> Yesterday I fetched a more recent version of the everything branch an=
d=20
> built a kernel with the latest patch from larry finger, I've planned =
to=20
> test it this afternoon, I'll publish then my results with this.
I finally conducted a test today.
My kernel is based on this commit 301df40749bdf144c72637795ba93d82e4b84=
682, and I used the patch published by Larry=20
=46inger on last thursday (title of the email : [PATCH V2] b43: Changes=
to enable BCM4311 rev 02 with wireless core=20
revision 13).
My results with this kernel are worser than with the previous.
Just after loading the driver I have this message :
Nov 25 13:26:04 ares kernel: [ 58.523036] b43-phy0 debug: Loading fir=
mware version 351.126 (2006-07-29 05:54:02)
Nov 25 13:26:04 ares kernel: [ 58.575722] WARNING: at=20
/usr/local/src/linux-2.6.24-git/drivers/net/wireless/b43/wa.c:657 b43_w=
a
_all()
Nov 25 13:26:04 ares kernel: [ 58.575738] [<f8ba0d57>] b43_wa_all+0x=
197/0x6c0 [b43]
Nov 25 13:26:04 ares kernel: [ 58.575759] [<f8b99aad>] b43_phy_inita=
+0x5d/0x500 [b43]
Nov 25 13:26:04 ares kernel: [ 58.575768] [<f8b9a407>] b43_phy_initb=
6+0x3e7/0x6a0 [b43]
Nov 25 13:26:04 ares kernel: [ 58.575783] [<f8b9ab76>] b43_phy_initg=
+0x36/0xe10 [b43]
Nov 25 13:26:04 ares kernel: [ 58.575796] [msleep+21/32] msleep+0x15=
/0x20
Nov 25 13:26:04 ares kernel: [ 58.575801] [<f8b99259>] b43_radio_sel=
ectchannel+0xf9/0x480 [b43]
Nov 25 13:26:04 ares kernel: [ 58.575821] [<f8b9bea7>] b43_phy_init+=
0x277/0x580 [b43]
Nov 25 13:26:04 ares kernel: [ 58.575835] [<f8b902e3>] b43_chip_init=
+0x443/0x920 [b43]
Nov 25 13:26:04 ares kernel: [ 58.575854] [<f8b90995>] b43_wireless_=
core_init+0x1d5/0x700 [b43]
Nov 25 13:26:04 ares kernel: [ 58.575870] [<f8b91d67>] b43_op_start+=
0x77/0x90 [b43]
Nov 25 13:26:04 ares kernel: [ 58.575882] [<f8bb3a5d>] ieee80211_ope=
n+0x15d/0x460 [mac80211]
=2E..
Nov 25 13:26:04 ares kernel: [ 58.576136] [sys_socketcall+591/640] s=
ys_socketcall+0x24f/0x280
Nov 25 13:26:04 ares kernel: [ 58.576149] [sys_time+10/48] sys_time+=
0xa/0x30
Nov 25 13:26:04 ares kernel: [ 58.576154] [sysenter_past_esp+95/133]=
sysenter_past_esp+0x5f/0x85
Nov 25 13:26:04 ares kernel: [ 58.576168] =3D=3D=3D=3D=3D=3D=3D=3D=3D=
=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D
Nov 25 13:26:05 ares kernel: [ 59.643488] b43-phy0 debug: Chip initia=
lized
Nov 25 13:26:05 ares kernel: [ 59.643714] b43-phy0 debug: 64-bit DMA =
initialized
Nov 25 13:26:05 ares kernel: [ 59.663763] b43-phy0 debug: Wireless in=
terface started
Nov 25 13:26:05 ares kernel: [ 59.663767] b43-phy0 debug: Adding Inte=
rface type 2
Nov 25 13:26:05 ares kernel: [ 59.664576] b43-phy0 ERROR: PHY transmi=
ssion error
Nov 25 13:26:05 ares kernel: [ 59.664653] b43-phy0 ERROR: Fatal DMA e=
rror: 0x00000400, 0x00000000, 0x00000000,=20
0x00000000, 0x00000000, 0x00000000
Nov 25 13:26:05 ares kernel: [ 59.664729] b43-phy0: Controller RESET =
(DMA error) ...
Nov 25 13:26:05 ares kernel: [ 59.665301] ADDRCONF(NETDEV_UP): wlan0:=
link is not ready
Nov 25 13:26:05 ares kernel: [ 59.711870] b43-phy0 debug: Wireless in=
terface stopped
Nov 25 13:26:05 ares kernel: [ 59.711907] b43-phy0 debug: DMA-64 0x02=
00 (RX) max used slots: 0/64
Nov 25 13:26:05 ares kernel: [ 59.711946] b43-phy0 debug: DMA-64 0x03=
40 (TX) max used slots: 0/128
Nov 25 13:26:05 ares kernel: [ 59.720294] b43-phy0 debug: DMA-64 0x03=
00 (TX) max used slots: 0/128
Nov 25 13:26:05 ares kernel: [ 59.727866] b43-phy0 debug: DMA-64 0x02=
C0 (TX) max used slots: 0/128
Nov 25 13:26:06 ares kernel: [ 59.736043] b43-phy0 debug: DMA-64 0x02=
80 (TX) max used slots: 0/128
Nov 25 13:26:06 ares kernel: [ 59.744027] b43-phy0 debug: DMA-64 0x02=
40 (TX) max used slots: 0/128
Nov 25 13:26:06 ares kernel: [ 59.751858] b43-phy0 debug: DMA-64 0x02=
00 (TX) max used slots: 0/128
Nov 25 13:26:06 ares kernel: [ 59.867946] b43-phy0 debug: Loading fir=
mware version 351.126 (2006-07-29 05:54:02)
Nov 25 13:26:06 ares kernel: [ 59.923806] WARNING: at=20
/usr/local/src/linux-2.6.24-git/drivers/net/wireless/b43/wa.c:657 b43_w=
a_all()
Nov 25 13:26:06 ares kernel: [ 59.923825] [<f8ba0d57>] b43_wa_all+0x=
197/0x6c0 [b43]
Nov 25 13:26:06 ares kernel: [ 59.923845] [<f8b99aad>] b43_phy_inita=
+0x5d/0x500 [b43]
Nov 25 13:26:06 ares kernel: [ 59.923855] [<f8b9a407>] b43_phy_initb=
6+0x3e7/0x6a0 [b43]
Nov 25 13:26:06 ares kernel: [ 59.923870] [<f8b9ab76>] b43_phy_initg=
+0x36/0xe10 [b43]
Nov 25 13:26:06 ares kernel: [ 59.923883] [msleep+21/32] msleep+0x15=
/0x20
And it keeps looping around the same set of message.
Any clue on to solve this problem ?
Any patch that i can test ?
Matthieu
-
To unsubscribe from this list: send the line "unsubscribe linux-wireles=
s" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
next prev parent reply other threads:[~2007-11-25 14:20 UTC|newest]
Thread overview: 5+ messages / expand[flat|nested] mbox.gz Atom feed top
2007-11-23 9:32 BCM4312 status Matthieu PATOU
2007-11-25 14:20 ` Matthieu PATOU [this message]
2007-11-25 15:51 ` Larry Finger
2007-11-25 18:25 ` Matthieu PATOU
2007-11-25 20:06 ` Stefano Brivio
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=474984B1.90302@matws.net \
--to=mat@matws.net \
--cc=linux-wireless@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.