From: Mark Paulus <mark.paulus@verizonbusiness.com>
To: Tejun Heo <htejun@gmail.com>
Cc: linux-ide@vger.kernel.org
Subject: Re: sata_sil issue on 2.6.22
Date: Fri, 30 Nov 2007 08:56:31 -0700 [thread overview]
Message-ID: <475032AF.6090001@verizonbusiness.com> (raw)
In-Reply-To: <474CC29E.8020102@gmail.com>
[-- Attachment #1: Type: text/plain, Size: 7154 bytes --]
Tejun Heo wrote:
> Hello,
>
> Mark Paulus wrote:
>> sata_sil 0000:02:0b.0: version 2.2
>> ACPI: PCI Interrupt 0000:02:0b.0[A] -> GSI 22 (level, low) -> IRQ 18
>> scsi0 : sata_sil
>> scsi1 : sata_sil
>> ata1: SATA max UDMA/100 cmd 0xe0812080 ctl 0xe081208a bmdma 0xe0812000
>> irq 18
>> ata2: SATA max UDMA/100 cmd 0xe08120c0 ctl 0xe08120ca bmdma 0xe0812008
>> irq 18
>> ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
>> ata1.00: ATA-5: ST310216A, 3.01, max UDMA/100
>> ata1.00: 19541088 sectors, multi 16: LBA ata1.00: applying bridge limits
>> ata1.00: failed to IDENTIFY (I/O error, err_mask=0x40)
>> ata1.00: revalidation failed (errno=-5)
>> ata1: failed to recover some devices, retrying in 5 secs
>> ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
>> ata1.00: failed to set xfermode (err_mask=0x40)
>> ata1.00: limiting speed to UDMA/100:PIO3
>> ata1: failed to recover some devices, retrying in 5 secs
>> ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
>> ata1.00: failed to set xfermode (err_mask=0x40)
>
> It looks like for some reason the port is being frozen repeatedly. Can
> you please apply the attached patch and post the dmesg?
>
> Thanks.
>
>
I applied the patch, and not much difference. Still the same issue, and here
is the new dmesg output.
SCSI subsystem initialized
libata version 2.21 loaded.
hda: Maxtor 34098H4, ATA DISK drive
hdb: WDC WD200BB-00DEA0, ATA DISK drive
hda: selected mode 0x45
hdb: selected mode 0x45
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: COMPAQ SC-148F, ATAPI CD/DVD-ROM drive
hdc: selected mode 0x22
ide1 at 0x170-0x177,0x376 on irq 15
ACPI: PCI Interrupt 0000:00:1f.4[C] -> GSI 23 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1f.4 to 64
uhci_hcd 0000:00:1f.4: UHCI Host Controller
uhci_hcd 0000:00:1f.4: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1f.4: irq 16, io base 0x00002440
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:02:08.0[A] -> GSI 20 (level, low) -> IRQ 17
e100: eth0: e100_probe: addr 0x41000000, irq 17, MAC addr 00:02:A5:10:5A:37
sata_sil 0000:02:0b.0: version 2.2
ACPI: PCI Interrupt 0000:02:0b.0[A] -> GSI 22 (level, low) -> IRQ 18
scsi0 : sata_sil
scsi1 : sata_sil
ata1: SATA max UDMA/100 cmd 0xe0812080 ctl 0xe081208a bmdma 0xe0812000 irq 18
ata2: SATA max UDMA/100 cmd 0xe08120c0 ctl 0xe08120ca bmdma 0xe0812008 irq 18
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.00: ATA-5: ST310216A, 3.01, max UDMA/100
ata1.00: 19541088 sectors, multi 16: LBA
ata1.00: applying bridge limits
ata1.00: failed to IDENTIFY (I/O error, err_mask=0x40)
ata1.00: revalidation failed (errno=-5)
ata1: failed to recover some devices, retrying in 5 secs
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.00: failed to IDENTIFY (I/O error, err_mask=0x40)
ata1.00: revalidation failed (errno=-5)
ata1.00: limiting speed to UDMA/100:PIO3
ata1: failed to recover some devices, retrying in 5 secs
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.00: failed to set xfermode (err_mask=0x40)
ata1.00: disabled
ata1: EH pending after completion, repeating EH (cnt=4)
ata1: exception Emask 0x10 SAct 0x0 SErr 0x0 action 0x2 frozen
ata1: hard resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.00: ATA-5: ST310216A, 3.01, max UDMA/100
ata1.00: 19541088 sectors, multi 16: LBA
ata1.00: applying bridge limits
ata1.00: failed to set xfermode (err_mask=0x40)
ata1: failed to recover some devices, retrying in 5 secs
ata1: hard resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.00: failed to IDENTIFY (I/O error, err_mask=0x40)
ata1.00: revalidation failed (errno=-5)
ata1.00: limiting speed to UDMA/100:PIO3
ata1: failed to recover some devices, retrying in 5 secs
ata1: hard resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.00: failed to set xfermode (err_mask=0x40)
ata1.00: disabled
ata1: EH pending after completion, repeating EH (cnt=3)
ata1: exception Emask 0x10 SAct 0x0 SErr 0x0 action 0x2 frozen
ata1: hard resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.00: ATA-5: ST310216A, 3.01, max UDMA/100
ata1.00: 19541088 sectors, multi 16: LBA
ata1.00: applying bridge limits
ata1.00: failed to set xfermode (err_mask=0x40)
ata1: failed to recover some devices, retrying in 5 secs
ata1: hard resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.00: failed to set xfermode (err_mask=0x40)
ata1.00: limiting speed to UDMA/100:PIO3
ata1: failed to recover some devices, retrying in 5 secs
ata1: hard resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.00: failed to set xfermode (err_mask=0x40)
ata1.00: disabled
ata1: EH pending after completion, repeating EH (cnt=2)
ata1: exception Emask 0x10 SAct 0x0 SErr 0x0 action 0x2 frozen
ata1: hard resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.00: ATA-5: ST310216A, 3.01, max UDMA/100
ata1.00: 19541088 sectors, multi 16: LBA
ata1.00: applying bridge limits
ata1.00: failed to set xfermode (err_mask=0x40)
ata1: failed to recover some devices, retrying in 5 secs
ata1: hard resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.00: failed to set xfermode (err_mask=0x40)
ata1.00: limiting speed to UDMA/100:PIO3
ata1: failed to recover some devices, retrying in 5 secs
ata1: hard resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.00: failed to set xfermode (err_mask=0x40)
ata1.00: disabled
ata1: EH pending after completion, repeating EH (cnt=1)
ata1: exception Emask 0x10 SAct 0x0 SErr 0x0 action 0x2 frozen
ata1: hard resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.00: ATA-5: ST310216A, 3.01, max UDMA/100
ata1.00: 19541088 sectors, multi 16: LBA
ata1.00: applying bridge limits
ata1.00: failed to set xfermode (err_mask=0x40)
ata1: failed to recover some devices, retrying in 5 secs
ata1: hard resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.00: failed to set xfermode (err_mask=0x40)
ata1.00: limiting speed to UDMA/100:PIO3
ata1: failed to recover some devices, retrying in 5 secs
ata1: hard resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.00: failed to set xfermode (err_mask=0x40)
ata1.00: disabled
ata1: EH pending after 5 tries, giving up
ata1: EH complete
ata2: SATA link down (SStatus 0 SControl 310)
hda: max request size: 128KiB
hda: 80043264 sectors (40982 MB) w/2048KiB Cache, CHS=65535/16/63, UDMA(100)
hda: cache flushes not supported
hda: hda1 hda2 < hda5 >
hdb: max request size: 128KiB
hdb: 39102336 sectors (20020 MB) w/8192KiB Cache, CHS=38792/16/63, UDMA(100)
hdb: cache flushes not supported
hdb: hdb1
hdc: ATAPI 48X CD-ROM drive, 128kB Cache, DMA
Uniform CD-ROM driver Revision: 3.20
--
Mark Paulus
2424 Garden of the Gods Rd | Phone: v622-5578 / 719-535-5578
0419/117 - LEC Access ; D5-1010 | FAX: 719-535-1665
Colo Springs, CO 80919 | 1800PageMCI / 1406052
AIM : mgpaulus1 / sametime : mark.paulus
[-- Attachment #2: mark_paulus.vcf --]
[-- Type: text/x-vcard, Size: 296 bytes --]
begin:vcard
fn:Mark Paulus
n:Paulus;Mark
org:MCI;Lec Interfaces / 40419
adr;dom:;;2424 Garden of the Gods Rd;Colorado Springs;CO;80919
email;internet:mark.paulus@verizonbusiness.com
title:Mark Paulus
tel;work:719-535-5578
tel;pager:800-pagemci / 1406052
tel;home:v622-5578
version:2.1
end:vcard
next prev parent reply other threads:[~2007-11-30 16:15 UTC|newest]
Thread overview: 9+ messages / expand[flat|nested] mbox.gz Atom feed top
2007-11-20 20:35 sata_sil issue on 2.6.22 Mark Paulus
2007-11-28 1:21 ` Tejun Heo
2007-11-30 15:56 ` Mark Paulus [this message]
2007-12-04 2:54 ` Tejun Heo
2007-12-05 14:29 ` Mark Paulus
2007-12-05 14:33 ` Tejun Heo
2007-12-05 14:49 ` Mark Paulus
2007-12-06 0:25 ` Tejun Heo
2007-12-06 2:10 ` Tejun Heo
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=475032AF.6090001@verizonbusiness.com \
--to=mark.paulus@verizonbusiness.com \
--cc=htejun@gmail.com \
--cc=linux-ide@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.