* [U-Boot-Users] [PATCH] ppc4xx: Use CFG_4xx_GPIO_TABLE to configure Korat board
@ 2008-01-03 20:02 Lawrence R. Johnson
0 siblings, 0 replies; only message in thread
From: Lawrence R. Johnson @ 2008-01-03 20:02 UTC (permalink / raw)
To: u-boot
Signed-off-by: Larry Johnson <lrj@acm.org>
---
N.B.: This patch depends on my previously-submitted patches for GPIO and
Korat.
board/korat/korat.c | 117 +++---------------------------------
include/configs/korat.h | 153 ++++++++++++++++++++++++++++++++++++++++++++++-
2 files changed, 161 insertions(+), 109 deletions(-)
diff --git a/board/korat/korat.c b/board/korat/korat.c
index 7cb9ee1..199c1ff 100644
--- a/board/korat/korat.c
+++ b/board/korat/korat.c
@@ -1,5 +1,5 @@
/*
- * (C) Copyright 2007
+ * (C) Copyright 2007-2008
* Larry Johnson, lrj at acm.org
*
* (C) Copyright 2006
@@ -26,6 +26,7 @@
*/
#include <common.h>
+#include <asm/gpio.h>
#include <asm/processor.h>
#include <asm-ppc/io.h>
#include <i2c.h>
@@ -40,7 +41,6 @@ ulong flash_get_size(ulong base, int banknum);
int board_early_init_f(void)
{
u32 sdr0_pfc1, sdr0_pfc2;
- u32 gpio0_ir;
u32 reg;
int eth;
@@ -48,102 +48,6 @@ int board_early_init_f(void)
mtdcr(ebccfgd, 0xb8400000);
/*--------------------------------------------------------------------
- * Setup the GPIO pins
- *
- * Korat GPIO usage:
- *
- * Init.
- * Pin Source I/O value Function
- * ------ ------ --- ----- ---------------------------------
- * GPIO00 Alt1 I/O x PerAddr07
- * GPIO01 Alt1 I/O x PerAddr06
- * GPIO02 Alt1 I/O x PerAddr05
- * GPIO03 GPIO x x GPIO03 to expansion bus connector
- * GPIO04 GPIO x x GPIO04 to expansion bus connector
- * GPIO05 GPIO x x GPIO05 to expansion bus connector
- * GPIO06 Alt1 O x PerCS1 (2nd NOR flash)
- * GPIO07 Alt1 O x PerCS2 (CPLD)
- * GPIO08 Alt1 O x PerCS3 to expansion bus connector
- * GPIO09 Alt1 O x PerCS4 to expansion bus connector
- * GPIO10 Alt1 O x PerCS5 to expansion bus connector
- * GPIO11 Alt1 I x PerErr
- * GPIO12 GPIO O 0 ATMega !Reset
- * GPIO13 GPIO O 1 SPI Atmega !SS
- * GPIO14 GPIO O 1 Write protect EEPROM #1 (0xA8)
- * GPIO15 GPIO O 0 CPU Run LED !On
- * GPIO16 Alt1 O x GMC1TxD0
- * GPIO17 Alt1 O x GMC1TxD1
- * GPIO18 Alt1 O x GMC1TxD2
- * GPIO19 Alt1 O x GMC1TxD3
- * GPIO20 Alt1 O x RejectPkt0
- * GPIO21 Alt1 O x RejectPkt1
- * GPIO22 GPIO I x PGOOD_DDR
- * GPIO23 Alt1 O x SCPD0
- * GPIO24 Alt1 O x GMC0TxD2
- * GPIO25 Alt1 O x GMC0TxD3
- * GPIO26 GPIO? I/O x IIC0SDA (selected in SDR0_PFC4)
- * GPIO27 GPIO O 0 PHY #0 1000BASE-X
- * GPIO28 GPIO O 0 PHY #1 1000BASE-X
- * GPIO29 GPIO I x Test jumper !Present
- * GPIO30 GPIO I x SFP module #0 !Present
- * GPIO31 GPIO I x SFP module #1 !Present
- *
- * GPIO32 GPIO O 1 SFP module #0 Tx !Enable
- * GPIO33 GPIO O 1 SFP module #1 Tx !Enable
- * GPIO34 Alt2 I x !UART1_CTS
- * GPIO35 Alt2 O x !UART1_RTS
- * GPIO36 Alt1 I x !UART0_CTS
- * GPIO37 Alt1 O x !UART0_RTS
- * GPIO38 Alt2 O x UART1_Tx
- * GPIO39 Alt2 I x UART1_Rx
- * GPIO40 Alt1 I x IRQ0 (Ethernet 0)
- * GPIO41 Alt1 I x IRQ1 (Ethernet 1)
- * GPIO42 Alt1 I x IRQ2 (PCI interrupt)
- * GPIO43 Alt1 I x IRQ3 (System Alert from CPLD)
- * GPIO44 xxxx x x (grounded through pulldown)
- * GPIO45 GPIO O 0 PHY #0 Enable
- * GPIO46 GPIO O 0 PHY #1 Enable
- * GPIO47 GPIO I x Reset switch !Pressed
- * GPIO48 GPIO I x Shutdown switch !Pressed
- * GPIO49 xxxx x x (reserved for trace port)
- * . . . . .
- * . . . . .
- * . . . . .
- * GPIO63 xxxx x x (reserved for trace port)
- *-------------------------------------------------------------------*/
-
- out_be32((u32 *) GPIO0_OR, 0x00060000);
- out_be32((u32 *) GPIO1_OR, 0xC0000000);
-
- out_be32((u32 *) GPIO0_OSRL, 0x54055400);
- out_be32((u32 *) GPIO0_OSRH, 0x55015000);
- out_be32((u32 *) GPIO1_OSRL, 0x02180000);
- out_be32((u32 *) GPIO1_OSRH, 0x00000000);
-
- out_be32((u32 *) GPIO0_TSRL, 0x54055500);
- out_be32((u32 *) GPIO0_TSRH, 0x00015000);
- out_be32((u32 *) GPIO1_TSRL, 0x00000000);
- out_be32((u32 *) GPIO1_TSRH, 0x00000000);
-
- out_be32((u32 *) GPIO0_TCR, 0x000FF0D8);
- out_be32((u32 *) GPIO1_TCR, 0xD6060000);
-
- out_be32((u32 *) GPIO0_ISR1L, 0x54000100);
- out_be32((u32 *) GPIO0_ISR1H, 0x00500000);
- out_be32((u32 *) GPIO1_ISR1L, 0x00405500);
- out_be32((u32 *) GPIO1_ISR1H, 0x00000000);
-
- out_be32((u32 *) GPIO0_ISR2L, 0x00000000);
- out_be32((u32 *) GPIO0_ISR2H, 0x00000000);
- out_be32((u32 *) GPIO1_ISR2L, 0x04010000);
- out_be32((u32 *) GPIO1_ISR2H, 0x00000000);
-
- out_be32((u32 *) GPIO0_ISR3L, 0x00000000);
- out_be32((u32 *) GPIO0_ISR3H, 0x00000000);
- out_be32((u32 *) GPIO1_ISR3L, 0x00000000);
- out_be32((u32 *) GPIO1_ISR3H, 0x00000000);
-
- /*--------------------------------------------------------------------
* Setup the interrupt controller polarities, triggers, etc.
*-------------------------------------------------------------------*/
mtdcr(uic0sr, 0xffffffff); /* clear all */
@@ -176,9 +80,8 @@ int board_early_init_f(void)
/* Configure the two Ethernet PHYs. For each PHY, configure for fiber
* if the SFP module is present, and for copper if it is not present.
*/
- gpio0_ir = in_be32((u32 *) GPIO0_IR);
for (eth = 0; eth < 2; ++eth) {
- if (gpio0_ir & (0x00000001 << (1 - eth))) {
+ if (gpio_read_in_bit(CFG_GPIO_SFP0_PRESENT_ + eth)) {
/* SFP module not present: configure PHY for copper. */
/* Set PHY to autonegotate 10 MB, 100MB, or 1 GB */
out_8((u8 *) CFG_CPLD_BASE + 0x06,
@@ -187,14 +90,13 @@ int board_early_init_f(void)
} else {
/* SFP module present: configure PHY for fiber and
enable output */
- out_be32((u32 *) GPIO0_OR, in_be32((u32 *) GPIO0_OR) |
- (0x00000001 << (4 - eth)));
- out_be32((u32 *) GPIO1_OR, in_be32((u32 *) GPIO1_OR) &
- ~(0x00000001 << (31 - eth)));
+ gpio_write_bit(CFG_GPIO_PHY0_FIBER_SEL + eth, 1);
+ gpio_write_bit(CFG_GPIO_SFP0_TX_EN_ + eth, 0);
}
}
/* enable Ethernet: set GPIO45 and GPIO46 to 1 */
- out_be32((u32 *) GPIO1_OR, in_be32((u32 *) GPIO1_OR) | 0x00060000);
+ gpio_write_bit(CFG_GPIO_PHY0_EN, 1);
+ gpio_write_bit(CFG_GPIO_PHY1_EN, 1);
/* select Ethernet pins */
mfsdr(SDR0_PFC1, sdr0_pfc1);
@@ -525,20 +427,19 @@ int checkboard(void)
{
char const *const s = getenv("serial#");
u8 const rev = in_8((u8 *) CFG_CPLD_BASE + 0);
- u32 const gpio0_or = in_be32((u32 *) GPIO0_OR);
printf("Board: Korat, Rev. %X", rev);
if (s != NULL)
printf(", serial# %s", s);
printf(", Ethernet PHY 0: ");
- if (gpio0_or & 0x00000010)
+ if (gpio_read_out_bit(CFG_GPIO_PHY0_FIBER_SEL))
printf("fiber");
else
printf("copper");
printf(", PHY 1: ");
- if (gpio0_or & 0x00000008)
+ if (gpio_read_out_bit(CFG_GPIO_PHY1_FIBER_SEL))
printf("fiber");
else
printf("copper");
diff --git a/include/configs/korat.h b/include/configs/korat.h
index 50bde96..5182972 100644
--- a/include/configs/korat.h
+++ b/include/configs/korat.h
@@ -1,5 +1,5 @@
/*
- * (C) Copyright 2007
+ * (C) Copyright 2007-2008
* Larry Johnson, lrj@acm.org
*
* (C) Copyright 2006-2007
@@ -360,6 +360,157 @@
#define CFG_EBC_PB2AP 0x04017300
#define CFG_EBC_PB2CR (CFG_CPLD_BASE | 0x00038000)
+/*-----------------------------------------------------------------------
+ * GPIO Setup
+ *
+ * Korat GPIO usage:
+ *
+ * Init.
+ * Pin Source I/O value Function
+ * ------ ------ --- ----- ---------------------------------
+ * GPIO00 Alt1 I/O x PerAddr07
+ * GPIO01 Alt1 I/O x PerAddr06
+ * GPIO02 Alt1 I/O x PerAddr05
+ * GPIO03 GPIO x x GPIO03 to expansion bus connector
+ * GPIO04 GPIO x x GPIO04 to expansion bus connector
+ * GPIO05 GPIO x x GPIO05 to expansion bus connector
+ * GPIO06 Alt1 O x PerCS1 (2nd NOR flash)
+ * GPIO07 Alt1 O x PerCS2 (CPLD)
+ * GPIO08 Alt1 O x PerCS3 to expansion bus connector
+ * GPIO09 Alt1 O x PerCS4 to expansion bus connector
+ * GPIO10 Alt1 O x PerCS5 to expansion bus connector
+ * GPIO11 Alt1 I x PerErr
+ * GPIO12 GPIO O 0 ATMega !Reset
+ * GPIO13 GPIO O 1 SPI Atmega !SS
+ * GPIO14 GPIO O 1 Write protect EEPROM #1 (0xA8)
+ * GPIO15 GPIO O 0 CPU Run LED !On
+ * GPIO16 Alt1 O x GMC1TxD0
+ * GPIO17 Alt1 O x GMC1TxD1
+ * GPIO18 Alt1 O x GMC1TxD2
+ * GPIO19 Alt1 O x GMC1TxD3
+ * GPIO20 Alt1 I x RejectPkt0
+ * GPIO21 Alt1 I x RejectPkt1
+ * GPIO22 GPIO I x PGOOD_DDR
+ * GPIO23 Alt1 O x SCPD0
+ * GPIO24 Alt1 O x GMC0TxD2
+ * GPIO25 Alt1 O x GMC0TxD3
+ * GPIO26 GPIO? I/O x IIC0SDA (selected in SDR0_PFC4)
+ * GPIO27 GPIO O 0 PHY #0 1000BASE-X select
+ * GPIO28 GPIO O 0 PHY #1 1000BASE-X select
+ * GPIO29 GPIO I x Test jumper !Present
+ * GPIO30 GPIO I x SFP module #0 !Present
+ * GPIO31 GPIO I x SFP module #1 !Present
+ *
+ * GPIO32 GPIO O 1 SFP module #0 Tx !Enable
+ * GPIO33 GPIO O 1 SFP module #1 Tx !Enable
+ * GPIO34 Alt2 I x !UART1_CTS
+ * GPIO35 Alt2 O x !UART1_RTS
+ * GPIO36 Alt1 I x !UART0_CTS
+ * GPIO37 Alt1 O x !UART0_RTS
+ * GPIO38 Alt2 O x UART1_Tx
+ * GPIO39 Alt2 I x UART1_Rx
+ * GPIO40 Alt1 I x IRQ0 (Ethernet 0)
+ * GPIO41 Alt1 I x IRQ1 (Ethernet 1)
+ * GPIO42 Alt1 I x IRQ2 (PCI interrupt)
+ * GPIO43 Alt1 I x IRQ3 (System Alert from CPLD)
+ * GPIO44 xxxx x x (grounded through pulldown)
+ * GPIO45 GPIO O 0 PHY #0 Enable
+ * GPIO46 GPIO O 0 PHY #1 Enable
+ * GPIO47 GPIO I x Reset switch !Pressed
+ * GPIO48 GPIO I x Shutdown switch !Pressed
+ * GPIO49 xxxx x x (reserved for trace port)
+ * . . . . .
+ * . . . . .
+ * . . . . .
+ * GPIO63 xxxx x x (reserved for trace port)
+*----------------------------------------------------------------------*/
+
+#define CFG_GPIO_ATMEGA_SS_ 13
+#define CFG_GPIO_PHY0_FIBER_SEL 27
+#define CFG_GPIO_PHY1_FIBER_SEL 28
+#define CFG_GPIO_SFP0_PRESENT_ 30
+#define CFG_GPIO_SFP1_PRESENT_ 31
+#define CFG_GPIO_SFP0_TX_EN_ 32
+#define CFG_GPIO_SFP1_TX_EN_ 33
+#define CFG_GPIO_PHY0_EN 45
+#define CFG_GPIO_PHY1_EN 46
+
+/*-----------------------------------------------------------------------
+ * PPC440 GPIO Configuration
+ */
+#define CFG_4xx_GPIO_TABLE { /* Out GPIO Alternate1 Alternate2 Alternate3 */ \
+{ \
+/* GPIO Core 0 */ \
+{GPIO0_BASE, GPIO_BI , GPIO_ALT1, GPIO_OUT_0}, /* GPIO0 EBC_ADDR(7) DMA_REQ(2) */ \
+{GPIO0_BASE, GPIO_BI , GPIO_ALT1, GPIO_OUT_0}, /* GPIO1 EBC_ADDR(6) DMA_ACK(2) */ \
+{GPIO0_BASE, GPIO_BI , GPIO_ALT1, GPIO_OUT_0}, /* GPIO2 EBC_ADDR(5) DMA_EOT/TC(2) */ \
+{GPIO0_BASE, GPIO_DIS, GPIO_SEL , GPIO_OUT_0}, /* GPIO3 EBC_ADDR(4) DMA_REQ(3) */ \
+{GPIO0_BASE, GPIO_DIS, GPIO_SEL , GPIO_OUT_0}, /* GPIO4 EBC_ADDR(3) DMA_ACK(3) */ \
+{GPIO0_BASE, GPIO_DIS, GPIO_SEL , GPIO_OUT_0}, /* GPIO5 EBC_ADDR(2) DMA_EOT/TC(3) */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO6 EBC_CS_N(1) */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO7 EBC_CS_N(2) */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO8 EBC_CS_N(3) */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO9 EBC_CS_N(4) */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO10 EBC_CS_N(5) */ \
+{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO11 EBC_BUS_ERR */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_0}, /* GPIO12 */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_1}, /* GPIO13 */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_1}, /* GPIO14 */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_0}, /* GPIO15 */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_1}, /* GPIO16 GMCTxD(4) */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_1}, /* GPIO17 GMCTxD(5) */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_1}, /* GPIO18 GMCTxD(6) */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_1}, /* GPIO19 GMCTxD(7) */ \
+{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO20 RejectPkt0 */ \
+{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO21 RejectPkt1 */ \
+{GPIO0_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO22 */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO23 SCPD0 */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_1}, /* GPIO24 GMCTxD(2) */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_1}, /* GPIO25 GMCTxD(3) */ \
+{GPIO0_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO26 */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_0}, /* GPIO27 EXT_EBC_REQ USB2D_RXERROR */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_0}, /* GPIO28 USB2D_TXVALID */ \
+{GPIO0_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO29 EBC_EXT_HDLA USB2D_PAD_SUSPNDM */ \
+{GPIO0_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO30 EBC_EXT_ACK USB2D_XCVRSELECT*/ \
+{GPIO0_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO31 EBC_EXR_BUSREQ USB2D_TERMSELECT*/ \
+}, \
+{ \
+/* GPIO Core 1 */ \
+{GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_1}, /* GPIO32 USB2D_OPMODE0 EBC_DATA(2) */ \
+{GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_1}, /* GPIO33 USB2D_OPMODE1 EBC_DATA(3) */ \
+{GPIO1_BASE, GPIO_IN , GPIO_ALT2, GPIO_OUT_0}, /* GPIO34 UART0_DCD_N UART1_DSR_CTS_N UART2_SOUT*/ \
+{GPIO1_BASE, GPIO_OUT, GPIO_ALT2, GPIO_OUT_1}, /* GPIO35 UART0_8PIN_DSR_N UART1_RTS_DTR_N UART2_SIN*/ \
+{GPIO1_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO36 UART0_8PIN_CTS_N EBC_DATA(0) UART3_SIN*/ \
+{GPIO1_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_1}, /* GPIO37 UART0_RTS_N EBC_DATA(1) UART3_SOUT*/ \
+{GPIO1_BASE, GPIO_OUT, GPIO_ALT2, GPIO_OUT_1}, /* GPIO38 UART0_DTR_N UART1_SOUT */ \
+{GPIO1_BASE, GPIO_IN , GPIO_ALT2, GPIO_OUT_0}, /* GPIO39 UART0_RI_N UART1_SIN */ \
+{GPIO1_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO40 UIC_IRQ(0) */ \
+{GPIO1_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO41 UIC_IRQ(1) */ \
+{GPIO1_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO42 UIC_IRQ(2) */ \
+{GPIO1_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO43 UIC_IRQ(3) */ \
+{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO44 UIC_IRQ(4) DMA_ACK(1) */ \
+{GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_0}, /* GPIO45 UIC_IRQ(6) DMA_EOT/TC(1) */ \
+{GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_0}, /* GPIO46 UIC_IRQ(7) DMA_REQ(0) */ \
+{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO47 UIC_IRQ(8) DMA_ACK(0) */ \
+{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO48 UIC_IRQ(9) DMA_EOT/TC(0) */ \
+{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO49 Unselect via TraceSelect Bit */ \
+{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO50 Unselect via TraceSelect Bit */ \
+{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO51 Unselect via TraceSelect Bit */ \
+{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO52 Unselect via TraceSelect Bit */ \
+{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO53 Unselect via TraceSelect Bit */ \
+{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO54 Unselect via TraceSelect Bit */ \
+{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO55 Unselect via TraceSelect Bit */ \
+{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO56 Unselect via TraceSelect Bit */ \
+{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO57 Unselect via TraceSelect Bit */ \
+{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO58 Unselect via TraceSelect Bit */ \
+{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO59 Unselect via TraceSelect Bit */ \
+{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO60 Unselect via TraceSelect Bit */ \
+{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO61 Unselect via TraceSelect Bit */ \
+{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO62 Unselect via TraceSelect Bit */ \
+{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO63 Unselect via TraceSelect Bit */ \
+} \
+}
+
/*
* Internal Definitions
*
^ permalink raw reply related [flat|nested] only message in thread
only message in thread, other threads:[~2008-01-03 20:02 UTC | newest]
Thread overview: (only message) (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2008-01-03 20:02 [U-Boot-Users] [PATCH] ppc4xx: Use CFG_4xx_GPIO_TABLE to configure Korat board Lawrence R. Johnson
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.