From mboxrd@z Thu Jan 1 00:00:00 1970 From: Peter Favrholdt Subject: Linux 2.6.24 sata_promise SATA300TX4 problems Date: Sat, 26 Jan 2008 11:23:53 +0100 Message-ID: <479B0A39.2050700@how.dk> Mime-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-15; format=flowed Content-Transfer-Encoding: 7bit Return-path: Received: from pqueuea.post.tele.dk ([193.162.153.9]:46704 "EHLO pqueuea.post.tele.dk" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S1751216AbYAZKqd (ORCPT ); Sat, 26 Jan 2008 05:46:33 -0500 Received: from pfepb.post.tele.dk (pfepb.post.tele.dk [195.41.46.236]) by pqueuea.post.tele.dk (Postfix) with ESMTP id 7AB50DC17F for ; Sat, 26 Jan 2008 11:25:59 +0100 (CET) Sender: linux-ide-owner@vger.kernel.org List-Id: linux-ide@vger.kernel.org To: linux-ide@vger.kernel.org, Mikael Pettersson Hi Mikael & list, I have previously reported problems with my setup: SATA300TX4 + 4 Seagate Barracuda ES 500GB I just tested with 2.6.24. After copying approx 25GB of each drive using dd if=/dev/sd[abcd] of=/dev/null bs=1M sda failed with the following message: [ 1060.069489] ata1: SError: { 10B8B Dispar BadCRC TrStaTrns } [ 1060.069498] ata1.00: cmd 25/00:00:90:2c:e6/00:02:01:00:00/e0 tag 0 dma 262144 in [ 1060.069501] res 40/00:28:00:00:00/00:00:00:00:00/40 Emask 0x4 (timeout) I have included lspci and dmesg output below. My system is rock solid using 2.6.21-rc2 with Mikael Pettersons 1.5Gbps patch. I will happily test any patch/suggestions thrown towards me :-) Best regards, Peter lspci -v (only the promise card): 01:08.0 Mass storage controller: Promise Technology, Inc. PDC40718 (SATA 300 TX4) (rev 02) Subsystem: Promise Technology, Inc. PDC40718 (SATA 300 TX4) Flags: bus master, 66MHz, medium devsel, latency 72, IRQ 19 I/O ports at a400 [size=128] I/O ports at a800 [size=256] Memory at e9024000 (32-bit, non-prefetchable) [size=4K] Memory at e9000000 (32-bit, non-prefetchable) [size=128K] [virtual] Expansion ROM at 300a0000 [disabled] [size=32K] Capabilities: [60] Power Management version 2 Kernel driver in use: sata_promise lspci: 00:00.0 Host bridge: nVidia Corporation nForce2 IGP2 (rev c1) 00:00.1 RAM memory: nVidia Corporation nForce2 Memory Controller 1 (rev c1) 00:00.2 RAM memory: nVidia Corporation nForce2 Memory Controller 4 (rev c1) 00:00.3 RAM memory: nVidia Corporation nForce2 Memory Controller 3 (rev c1) 00:00.4 RAM memory: nVidia Corporation nForce2 Memory Controller 2 (rev c1) 00:00.5 RAM memory: nVidia Corporation nForce2 Memory Controller 5 (rev c1) 00:01.0 ISA bridge: nVidia Corporation nForce2 ISA Bridge (rev a4) 00:01.1 SMBus: nVidia Corporation nForce2 SMBus (MCP) (rev a2) 00:02.0 USB Controller: nVidia Corporation nForce2 USB Controller (rev a4) 00:02.1 USB Controller: nVidia Corporation nForce2 USB Controller (rev a4) 00:02.2 USB Controller: nVidia Corporation nForce2 USB Controller (rev a4) 00:04.0 Ethernet controller: nVidia Corporation nForce2 Ethernet Controller (rev a1) 00:05.0 Multimedia audio controller: nVidia Corporation nForce Audio Processing Unit (rev a2) 00:06.0 Multimedia audio controller: nVidia Corporation nForce2 AC97 Audio Controler (MCP) (rev a1) 00:08.0 PCI bridge: nVidia Corporation nForce2 External PCI Bridge (rev a3) 00:09.0 IDE interface: nVidia Corporation nForce2 IDE (rev a2) 00:0d.0 FireWire (IEEE 1394): nVidia Corporation nForce2 FireWire (IEEE 1394) Controller (rev a3) 00:1e.0 PCI bridge: nVidia Corporation nForce2 AGP (rev c1) 01:04.0 Ethernet controller: Marvell Technology Group Ltd. 88E8001 Gigabit Ethernet Controller (rev 13) 01:08.0 Mass storage controller: Promise Technology, Inc. PDC40718 (SATA 300 TX4) (rev 02) 01:0b.0 RAID bus controller: Silicon Image, Inc. SiI 3112 [SATALink/SATARaid] Serial ATA Controller (rev 02) 03:00.0 VGA compatible controller: Matrox Graphics, Inc. MGA G550 AGP (rev 01) Here is my complete dmesg: [ 24.897952] forcedeth: Reverse Engineered nForce ethernet driver. Version 0.61. [ 24.898267] ACPI: PCI Interrupt Link [APCH] enabled at IRQ 22 [ 24.898317] ACPI: PCI Interrupt 0000:00:04.0[A] -> Link [APCH] -> GSI 22 (level, high) -> IRQ 18 [ 24.898440] PCI: Setting latency timer of device 0000:00:04.0 to 64 [ 25.051795] Switched to high resolution mode on CPU 0 [ 25.421997] forcedeth 0000:00:04.0: ifname eth1, PHY OUI 0x20 @ 1, addr 00:11:2f:10:c1:c8 [ 25.422057] forcedeth 0000:00:04.0: timirq lnktim desc-v1 [ 25.422118] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 [ 25.422169] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx [ 25.422284] NFORCE2: IDE controller (0x10de:0x0065 rev 0xa2) at PCI slot 0000:00:09.0 [ 25.422355] NFORCE2: not 100% native mode: will probe irqs later [ 25.422405] NFORCE2: BIOS didn't set cable bits correctly. Enabling workaround. [ 25.422465] NFORCE2: 0000:00:09.0 (rev a2) UDMA133 controller [ 25.422516] ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:DMA [ 25.422642] ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:DMA [ 25.422798] Probing IDE interface ide0... [ 25.731527] hdb: ST380021A, ATA DISK drive [ 26.091338] hda: ST380021A, ATA DISK drive [ 26.091419] hda: host max PIO5 wanted PIO255(auto-tune) selected PIO4 [ 26.091509] hda: UDMA/100 mode selected [ 26.091635] hdb: host max PIO5 wanted PIO255(auto-tune) selected PIO4 [ 26.091984] hdb: UDMA/100 mode selected [ 26.092132] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 [ 26.092294] Probing IDE interface ide1... [ 27.300704] hdc: HITACHI DVD-ROM GD-2500, ATAPI CD/DVD-ROM drive [ 27.300856] hdc: host max PIO5 wanted PIO255(auto-tune) selected PIO4 [ 27.359737] hdc: MWDMA2 mode selected [ 27.360303] ide1 at 0x170-0x177,0x376 on irq 15 [ 27.360515] hda: max request size: 128KiB [ 27.360881] hda: 156301488 sectors (80026 MB) w/2048KiB Cache, CHS=65535/16/63 [ 27.361001] hda: cache flushes not supported [ 27.361072] hda: hda1 hda2 < hda5 hda6 hda7 hda8 > [ 27.422072] hdb: max request size: 128KiB [ 27.422450] hdb: 156301488 sectors (80026 MB) w/2048KiB Cache, CHS=65535/16/63 [ 27.422569] hdb: cache flushes not supported [ 27.422631] hdb: hdb1 hdb2 < hdb5 hdb6 hdb7 hdb8 hdb9 > [ 27.554655] hdc: ATAPI 24X DVD-ROM drive, 512kB Cache [ 27.554828] Uniform CD-ROM driver Revision: 3.20 [ 27.557777] Driver 'sd' needs updating - please use bus_type methods [ 27.557849] Driver 'sr' needs updating - please use bus_type methods [ 27.557978] sata_promise 0000:01:08.0: version 2.11 [ 27.558158] ACPI: PCI Interrupt Link [APC3] enabled at IRQ 18 [ 27.558209] ACPI: PCI Interrupt 0000:01:08.0[A] -> Link [APC3] -> GSI 18 (level, high) -> IRQ 19 [ 27.558503] scsi0 : sata_promise [ 27.558622] scsi1 : sata_promise [ 27.558719] scsi2 : sata_promise [ 27.558817] scsi3 : sata_promise [ 27.558908] ata1: SATA max UDMA/133 mmio m4096@0xe9024000 port 0xe9024380 irq 19 [ 27.558967] ata2: SATA max UDMA/133 mmio m4096@0xe9024000 port 0xe9024280 irq 19 [ 27.559026] ata3: SATA max UDMA/133 mmio m4096@0xe9024000 port 0xe9024200 irq 19 [ 27.559084] ata4: SATA max UDMA/133 mmio m4096@0xe9024000 port 0xe9024300 irq 19 [ 28.040224] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 28.095145] ata1.00: ATA-7: ST3500630NS, 3.AEE, max UDMA/133 [ 28.095193] ata1.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 0/32) [ 28.178404] ata1.00: configured for UDMA/133 [ 28.659895] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 28.707063] ata2.00: ATA-7: ST3500630NS, 3.AEE, max UDMA/133 [ 28.707111] ata2.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 0/32) [ 28.790326] ata2.00: configured for UDMA/133 [ 29.279570] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 29.331818] ata3.00: ATA-7: ST3500630NS, 3.AEE, max UDMA/133 [ 29.331867] ata3.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 0/32) [ 29.423407] ata3.00: configured for UDMA/133 [ 29.909240] ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 29.959518] ata4.00: ATA-7: ST3500630NS, 3.AEE, max UDMA/133 [ 29.959566] ata4.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 0/32) [ 30.051097] ata4.00: configured for UDMA/133 [ 30.051231] scsi 0:0:0:0: Direct-Access ATA ST3500630NS 3.AE PQ: 0 ANSI: 5 [ 30.051395] sd 0:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB) [ 30.051456] sd 0:0:0:0: [sda] Write Protect is off [ 30.051503] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 30.051519] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 30.051614] sd 0:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB) [ 30.051671] sd 0:0:0:0: [sda] Write Protect is off [ 30.051718] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 30.051732] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 30.051791] sda: unknown partition table [ 30.066602] sd 0:0:0:0: [sda] Attached SCSI disk [ 30.066719] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 30.067030] scsi 1:0:0:0: Direct-Access ATA ST3500630NS 3.AE PQ: 0 ANSI: 5 [ 30.067184] sd 1:0:0:0: [sdb] 976773168 512-byte hardware sectors (500108 MB) [ 30.067241] sd 1:0:0:0: [sdb] Write Protect is off [ 30.067288] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00 [ 30.067302] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 30.067390] sd 1:0:0:0: [sdb] 976773168 512-byte hardware sectors (500108 MB) [ 30.067447] sd 1:0:0:0: [sdb] Write Protect is off [ 30.067493] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00 [ 30.067507] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 30.067567] sdb: unknown partition table [ 30.087344] sd 1:0:0:0: [sdb] Attached SCSI disk [ 30.087451] sd 1:0:0:0: Attached scsi generic sg1 type 0 [ 30.087758] scsi 2:0:0:0: Direct-Access ATA ST3500630NS 3.AE PQ: 0 ANSI: 5 [ 30.087913] sd 2:0:0:0: [sdc] 976773168 512-byte hardware sectors (500108 MB) [ 30.087970] sd 2:0:0:0: [sdc] Write Protect is off [ 30.088017] sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00 [ 30.088031] sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 30.088121] sd 2:0:0:0: [sdc] 976773168 512-byte hardware sectors (500108 MB) [ 30.088177] sd 2:0:0:0: [sdc] Write Protect is off [ 30.088224] sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00 [ 30.088238] sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 30.088297] sdc: unknown partition table [ 30.104312] sd 2:0:0:0: [sdc] Attached SCSI disk [ 30.104418] sd 2:0:0:0: Attached scsi generic sg2 type 0 [ 30.104724] scsi 3:0:0:0: Direct-Access ATA ST3500630NS 3.AE PQ: 0 ANSI: 5 [ 30.104871] sd 3:0:0:0: [sdd] 976773168 512-byte hardware sectors (500108 MB) [ 30.104928] sd 3:0:0:0: [sdd] Write Protect is off [ 30.104975] sd 3:0:0:0: [sdd] Mode Sense: 00 3a 00 00 [ 30.104989] sd 3:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 30.105076] sd 3:0:0:0: [sdd] 976773168 512-byte hardware sectors (500108 MB) [ 30.105132] sd 3:0:0:0: [sdd] Write Protect is off [ 30.105178] sd 3:0:0:0: [sdd] Mode Sense: 00 3a 00 00 [ 30.105192] sd 3:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 30.105251] sdd: unknown partition table [ 30.115877] sd 3:0:0:0: [sdd] Attached SCSI disk [ 30.115988] sd 3:0:0:0: Attached scsi generic sg3 type 0 [ 30.116302] sata_sil 0000:01:0b.0: version 2.3 [ 30.116362] ACPI: PCI Interrupt 0000:01:0b.0[A] -> Link [APC3] -> GSI 18 (level, high) -> IRQ 19 [ 30.116530] scsi4 : sata_sil [ 30.116632] scsi5 : sata_sil [ 30.116722] ata5: SATA max UDMA/100 mmio m512@0xe9025000 tf 0xe9025080 irq 19 [ 30.116774] ata6: SATA max UDMA/100 mmio m512@0xe9025000 tf 0xe90250c0 irq 19 [ 30.438948] ata5: SATA link down (SStatus 0 SControl 310) [ 30.768774] ata6: SATA link down (SStatus 0 SControl 310) [ 30.770218] ACPI: PCI Interrupt Link [APCL] enabled at IRQ 21 [ 30.770270] ACPI: PCI Interrupt 0000:00:02.2[C] -> Link [APCL] -> GSI 21 (level, high) -> IRQ 20 [ 30.770396] PCI: Setting latency timer of device 0000:00:02.2 to 64 [ 30.770400] ehci_hcd 0000:00:02.2: EHCI Host Controller [ 30.770509] ehci_hcd 0000:00:02.2: new USB bus registered, assigned bus number 1 [ 30.770603] ehci_hcd 0000:00:02.2: debug port 1 [ 30.770652] PCI: cache line size of 64 is not supported by device 0000:00:02.2 [ 30.770661] ehci_hcd 0000:00:02.2: irq 20, io mem 0xea083000 [ 30.788757] ehci_hcd 0000:00:02.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 [ 30.788985] usb usb1: configuration #1 chosen from 1 choice [ 30.789075] hub 1-0:1.0: USB hub found [ 30.789129] hub 1-0:1.0: 6 ports detected [ 30.898798] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver [ 30.899088] ACPI: PCI Interrupt Link [APCF] enabled at IRQ 20 [ 30.899138] ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [APCF] -> GSI 20 (level, high) -> IRQ 21 [ 30.899264] PCI: Setting latency timer of device 0000:00:02.0 to 64 [ 30.899268] ohci_hcd 0000:00:02.0: OHCI Host Controller [ 30.899353] ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 2 [ 30.899422] ohci_hcd 0000:00:02.0: irq 21, io mem 0xea087000 [ 30.960777] usb usb2: configuration #1 chosen from 1 choice [ 30.960862] hub 2-0:1.0: USB hub found [ 30.960916] hub 2-0:1.0: 3 ports detected [ 31.068949] ACPI: PCI Interrupt Link [APCG] enabled at IRQ 22 [ 31.068998] ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [APCG] -> GSI 22 (level, high) -> IRQ 18 [ 31.069125] PCI: Setting latency timer of device 0000:00:02.1 to 64 [ 31.069129] ohci_hcd 0000:00:02.1: OHCI Host Controller [ 31.069214] ohci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 3 [ 31.069282] ohci_hcd 0000:00:02.1: irq 18, io mem 0xea082000 [ 31.130689] usb usb3: configuration #1 chosen from 1 choice [ 31.130779] hub 3-0:1.0: USB hub found [ 31.130833] hub 3-0:1.0: 3 ports detected [ 31.238724] PNP: No PS/2 controller found. Probing ports directly. [ 31.488773] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 31.488928] mice: PS/2 mouse device common for all mice [ 31.489008] i2c /dev entries driver [ 31.489216] i2c-adapter i2c-0: nForce2 SMBus adapter at 0x5000 [ 31.489329] i2c-adapter i2c-1: nForce2 SMBus adapter at 0x5500 [ 31.638311] usb 2-1: new low speed USB device using ohci_hcd and address 2 [ 31.828263] usb 2-1: configuration #1 chosen from 1 choice [ 32.128054] usb 2-2: new low speed USB device using ohci_hcd and address 3 [ 32.317993] raid6: int32x1 728 MB/s [ 32.487918] raid6: int32x2 728 MB/s [ 32.657815] raid6: int32x4 681 MB/s [ 32.827763] raid6: int32x8 608 MB/s [ 32.997627] raid6: mmxx1 1513 MB/s [ 33.167530] raid6: mmxx2 2385 MB/s [ 33.337463] raid6: sse1x1 1399 MB/s [ 33.507345] raid6: sse1x2 2149 MB/s [ 33.507390] raid6: using algorithm sse1x2 (2149 MB/s) [ 33.507437] md: raid6 personality registered for level 6 [ 33.507485] md: raid5 personality registered for level 5 [ 33.507531] md: raid4 personality registered for level 4 [ 33.507635] device-mapper: ioctl: 4.12.0-ioctl (2007-10-02) initialised: dm-devel@redhat.com [ 33.507758] TCP cubic registered [ 33.507809] Using IPI Shortcut mode [ 33.508092] md: Autodetecting RAID arrays. [ 33.508138] md: Scanned 0 and added 0 devices. [ 33.508183] md: autorun ... [ 33.508226] md: ... autorun DONE. [ 33.519306] kjournald starting. Commit interval 5 seconds [ 33.519361] EXT3-fs: mounted filesystem with ordered data mode. [ 33.519413] VFS: Mounted root (ext3 filesystem) readonly. [ 33.519693] Freeing unused kernel memory: 188k freed [ 33.616174] usb 2-2: configuration #1 chosen from 1 choice [ 34.373020] NET: Registered protocol family 1 [ 36.545839] hdc: drive_cmd: status=0x51 { DriveReady SeekComplete Error } [ 36.546026] hdc: drive_cmd: error=0x04 { AbortedCommand } [ 36.546135] ide: failed opcode was: 0xe3 [ 37.267015] input: PC Speaker as /class/input/input2 [ 37.321217] usbcore: registered new interface driver hiddev [ 37.326352] ACPI: PCI Interrupt Link [APCM] enabled at IRQ 21 [ 37.326408] ACPI: PCI Interrupt 0000:00:0d.0[A] -> Link [APCM] -> GSI 21 (level, high) -> IRQ 20 [ 37.326533] PCI: Setting latency timer of device 0000:00:0d.0 to 64 [ 37.377141] input: Logitech USB Receiver as /class/input/input3 [ 37.387211] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[20] MMIO=[ea084000-ea0847ff] Max Packet=[2048] IR/IT contexts=[4/4] [ 37.435354] input: USB HID v1.10 Keyboard [Logitech USB Receiver] on usb-0000:00:02.0-1 [ 37.446186] input: Logitech USB Receiver as /class/input/input4 [ 37.505340] input: USB HID v1.10 Mouse [Logitech USB Receiver] on usb-0000:00:02.0-1 [ 37.513023] input: Logitech USB-PS/2 Trackball as /class/input/input5 [ 37.575333] input: USB HID v1.00 Mouse [Logitech USB-PS/2 Trackball] on usb-0000:00:02.0-2 [ 37.575478] usbcore: registered new interface driver usbhid [ 37.575528] drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver [ 37.620028] ACPI: PCI Interrupt Link [APCJ] enabled at IRQ 20 [ 37.620084] ACPI: PCI Interrupt 0000:00:06.0[A] -> Link [APCJ] -> GSI 20 (level, high) -> IRQ 21 [ 37.620226] PCI: Setting latency timer of device 0000:00:06.0 to 64 [ 37.955010] intel8x0_measure_ac97_clock: measured 58784 usecs [ 37.955065] intel8x0: clocking to 48000 [ 38.494913] ohci1394: fw-host0: SelfID received outside of bus reset sequence [ 38.814700] ieee1394: Host added: ID:BUS[0-00:1023] GUID[00e01800007b0179] [ 39.054650] hdc: drive_cmd: status=0x51 { DriveReady SeekComplete Error } [ 39.054830] hdc: drive_cmd: error=0x04 { AbortedCommand } [ 39.054939] ide: failed opcode was: 0xe3 [ 39.483047] Adding 979924k swap on /dev/hda7. Priority:-1 extents:1 across:979924k [ 39.740419] EXT3 FS on hda8, internal journal [ 40.991735] md: md0 stopped. [ 41.101335] md: bind [ 41.101533] md: bind [ 41.101710] md: bind [ 41.101873] md: bind [ 41.108620] raid5: device sda operational as raid disk 0 [ 41.108672] raid5: device sdb operational as raid disk 3 [ 41.108719] raid5: device sdc operational as raid disk 2 [ 41.108766] raid5: device sdd operational as raid disk 1 [ 41.109238] raid5: allocated 4203kB for md0 [ 41.109284] raid5: raid level 5 set md0 active with 4 out of 4 devices, algorithm 2 [ 41.109342] RAID5 conf printout: [ 41.109386] --- rd:4 wd:4 [ 41.109429] disk 0, o:1, dev:sda [ 41.109473] disk 1, o:1, dev:sdd [ 41.109516] disk 2, o:1, dev:sdc [ 41.109560] disk 3, o:1, dev:sdb [ 52.301250] ReiserFS: hda6: found reiserfs format "3.6" with standard journal [ 52.301321] ReiserFS: hda6: using ordered data mode [ 52.306452] ReiserFS: hda6: journal params: device hda6, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 [ 52.307509] ReiserFS: hda6: checking transaction log (hda6) [ 52.357121] ReiserFS: hda6: Using r5 hash to sort names [ 52.482552] kjournald starting. Commit interval 5 seconds [ 52.529309] EXT3 FS on md0, internal journal [ 52.530417] EXT3-fs: mounted filesystem with ordered data mode. [ 53.555062] skge eth0: enabling interface [ 58.325139] skge eth0: Link is up at 100 Mbps, full duplex, flow control both [ 61.194087] lp0: using parport0 (interrupt-driven). [ 61.202660] ppdev: user-space parallel port driver [ 1060.069478] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x1380000 action 0x2 frozen [ 1060.069489] ata1: SError: { 10B8B Dispar BadCRC TrStaTrns } [ 1060.069498] ata1.00: cmd 25/00:00:90:2c:e6/00:02:01:00:00/e0 tag 0 dma 262144 in [ 1060.069501] res 40/00:28:00:00:00/00:00:00:00:00/40 Emask 0x4 (timeout) [ 1060.069505] ata1.00: status: { DRDY } [ 1065.437567] ata1: port is slow to respond, please be patient (Status 0xff) [ 1070.114210] ata1: device not ready (errno=-16), forcing hardreset [ 1070.114219] ata1: hard resetting link [ 1076.320932] ata1: port is slow to respond, please be patient (Status 0xff) [ 1080.158924] ata1: COMRESET failed (errno=-16) [ 1080.158934] ata1: hard resetting link [ 1086.365744] ata1: port is slow to respond, please be patient (Status 0xff) [ 1090.203665] ata1: COMRESET failed (errno=-16) [ 1090.203675] ata1: hard resetting link [ 1096.410416] ata1: port is slow to respond, please be patient (Status 0xff) [ 1125.195332] ata1: COMRESET failed (errno=-16) [ 1125.195344] ata1: limiting SATA link speed to 1.5 Gbps [ 1125.195348] ata1: hard resetting link [ 1130.202827] ata1: COMRESET failed (errno=-16) [ 1130.202837] ata1: reset failed, giving up [ 1130.202841] ata1.00: disabled [ 1130.202864] ata1: exception Emask 0x10 SAct 0x0 SErr 0x1390002 action 0xa frozen t4 [ 1130.202867] ata1: hotplug_status 0x80 [ 1130.202871] ata1: SError: { RecovComm PHYRdyChg 10B8B Dispar BadCRC TrStaTrns } [ 1130.202908] ata1: hard resetting link [ 1136.810334] ata1: port is slow to respond, please be patient (Status 0xff) [ 1140.227798] ata1: COMRESET failed (errno=-16) [ 1140.227808] ata1: hard resetting link [ 1146.843986] ata1: port is slow to respond, please be patient (Status 0xff) [ 1150.262189] ata1: COMRESET failed (errno=-16) [ 1150.262199] ata1: hard resetting link [ 1156.868724] ata1: port is slow to respond, please be patient (Status 0xff) [ 1185.283976] ata1: COMRESET failed (errno=-16) [ 1185.283996] ata1: limiting SATA link speed to 1.5 Gbps [ 1185.283999] ata1: hard resetting link [ 1190.331327] ata1: COMRESET failed (errno=-16) [ 1190.331337] ata1: reset failed, giving up [ 1190.331352] ata1: exception Emask 0x10 SAct 0x0 SErr 0x1390002 action 0xa frozen t3 [ 1190.331356] ata1: hotplug_status 0x80 [ 1190.331360] ata1: SError: { RecovComm PHYRdyChg 10B8B Dispar BadCRC TrStaTrns } [ 1190.331396] ata1: hard resetting link [ 1196.937871] ata1: port is slow to respond, please be patient (Status 0xff) [ 1200.365980] ata1: COMRESET failed (errno=-16) [ 1200.365990] ata1: hard resetting link [ 1206.972464] ata1: port is slow to respond, please be patient (Status 0xff) [ 1210.390683] ata1: COMRESET failed (errno=-16) [ 1210.390693] ata1: hard resetting link [ 1217.008237] ata1: port is slow to respond, please be patient (Status 0xff) [ 1245.392315] ata1: COMRESET failed (errno=-16) [ 1245.392325] ata1: limiting SATA link speed to 1.5 Gbps [ 1245.392328] ata1: hard resetting link [ 1250.450259] ata1: COMRESET failed (errno=-16) [ 1250.450268] ata1: reset failed, giving up [ 1250.450281] ata1: exception Emask 0x10 SAct 0x0 SErr 0x1390002 action 0xa frozen t2 [ 1250.450284] ata1: hotplug_status 0x80 [ 1250.450289] ata1: SError: { RecovComm PHYRdyChg 10B8B Dispar BadCRC TrStaTrns } [ 1250.450304] ata1: hard resetting link [ 1257.056218] ata1: port is slow to respond, please be patient (Status 0xff) [ 1260.484408] ata1: COMRESET failed (errno=-16) [ 1260.484417] ata1: hard resetting link [ 1267.072563] ata1: port is slow to respond, please be patient (Status 0xff) [ 1270.499165] ata1: COMRESET failed (errno=-16) [ 1270.499174] ata1: hard resetting link [ 1277.075718] ata1: port is slow to respond, please be patient (Status 0xff) [ 1305.530799] ata1: COMRESET failed (errno=-16) [ 1305.530809] ata1: limiting SATA link speed to 1.5 Gbps [ 1305.530813] ata1: hard resetting link [ 1310.578793] ata1: COMRESET failed (errno=-16) [ 1310.578801] ata1: reset failed, giving up [ 1310.578814] ata1: exception Emask 0x10 SAct 0x0 SErr 0x1390002 action 0xa frozen t1 [ 1310.578817] ata1: hotplug_status 0x80 [ 1310.578822] ata1: SError: { RecovComm PHYRdyChg 10B8B Dispar BadCRC TrStaTrns } [ 1310.578837] ata1: hard resetting link [ 1317.184707] ata1: port is slow to respond, please be patient (Status 0xff) [ 1320.602902] ata1: COMRESET failed (errno=-16) [ 1320.602911] ata1: hard resetting link [ 1327.209508] ata1: port is slow to respond, please be patient (Status 0xff) [ 1330.627649] ata1: COMRESET failed (errno=-16) [ 1330.627657] ata1: hard resetting link [ 1337.234946] ata1: port is slow to respond, please be patient (Status 0xff) [ 1365.669300] ata1: COMRESET failed (errno=-16) [ 1365.669311] ata1: limiting SATA link speed to 1.5 Gbps [ 1365.669314] ata1: hard resetting link [ 1370.716641] ata1: COMRESET failed (errno=-16) [ 1370.716650] ata1: reset failed, giving up [ 1370.716656] ata1: EH pending after 5 tries, giving up [ 1370.716684] sd 0:0:0:0: [sda] Result: hostbyte=0x00 driverbyte=0x08 [ 1370.716688] sd 0:0:0:0: [sda] Sense Key : 0xb [current] [descriptor] [ 1370.716693] Descriptor sense data with sense descriptors (in hex): [ 1370.716696] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00 [ 1370.716703] 00 00 00 00 [ 1370.716706] sd 0:0:0:0: [sda] ASC=0x0 ASCQ=0x0 [ 1370.716710] end_request: I/O error, dev sda, sector 31861904 [ 1370.716715] Buffer I/O error on device sda, logical block 3982738 [ 1370.716722] Buffer I/O error on device sda, logical block 3982739 [ 1370.716726] Buffer I/O error on device sda, logical block 3982740 [ 1370.716730] Buffer I/O error on device sda, logical block 3982741 [ 1370.716733] Buffer I/O error on device sda, logical block 3982742 [ 1370.716737] Buffer I/O error on device sda, logical block 3982743 [ 1370.716741] Buffer I/O error on device sda, logical block 3982744 [ 1370.716744] Buffer I/O error on device sda, logical block 3982745 [ 1370.716748] Buffer I/O error on device sda, logical block 3982746 [ 1370.716752] Buffer I/O error on device sda, logical block 3982747 [ 1370.716795] ata1: EH complete [ 1370.716992] sd 0:0:0:0: rejecting I/O to offline device [ 1370.717003] ata1.00: detaching (SCSI 0:0:0:0) [ 1370.717222] sd 0:0:0:0: [sda] Synchronizing SCSI cache [ 1370.718840] sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00 [ 1370.718847] sd 0:0:0:0: [sda] Stopping disk [ 1370.718855] sd 0:0:0:0: [sda] START_STOP FAILED [ 1370.718857] sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00