From: Jens Rottmann <JRottmann@LiPPERT-AT.de>
To: Antonino Daplas <adaplas@gmail.com>
Cc: linux-fbdev-devel@lists.sourceforge.net
Subject: [PATCH] lxfb: extend PLL table to support dotclocks below 25 MHz
Date: Mon, 28 Jan 2008 14:00:27 +0100 [thread overview]
Message-ID: <479DD1EB.2070202@LiPPERT-AT.de> (raw)
Hi,
I needed this to use a 320x240 TFT (Sharp LQ038Q5DR01, 6.8 MHz dotclock) on a
AMD Geode-LX board. Tested with 2.6.23.14 and 2.6.24.
What do you think?
Best regards,
Jens Rottmann
------------------X8-----------------X8-------------------------
lxfb: extend PLL table to support dotclocks below 25 MHz
Extends the PLL frequency table of the AMD Geode-LX frame buffer
driver to make use of the DIV4 bit, thus adding support for
dotclocks between 6 and 25 MHz. These are needed for small LCDs
(e.g. 320x240). Also inserts some intermediate steps between
pre-existing frequencies.
Signed-off-by: Jens Rottmann <JRottmann at LiPPERT-AT. de>
---
--- linux-2.6.24/drivers/video/geode/lxfb_ops.c
+++ lxfb_clocks_added/drivers/video/geode/lxfb_ops.c
@@ -34,35 +34,85 @@ static const struct {
unsigned int pllval;
unsigned int freq;
} pll_table[] = {
- { 0x000031AC, 24923 },
- { 0x0000215D, 25175 },
- { 0x00001087, 27000 },
- { 0x0000216C, 28322 },
- { 0x0000218D, 28560 },
- { 0x000010C9, 31200 },
- { 0x00003147, 31500 },
- { 0x000010A7, 33032 },
- { 0x00002159, 35112 },
- { 0x00004249, 35500 },
- { 0x00000057, 36000 },
- { 0x0000219A, 37889 },
- { 0x00002158, 39168 },
- { 0x00000045, 40000 },
- { 0x00000089, 43163 },
- { 0x000010E7, 44900 },
- { 0x00002136, 45720 },
- { 0x00003207, 49500 },
- { 0x00002187, 50000 },
- { 0x00004286, 56250 },
- { 0x000010E5, 60065 },
- { 0x00004214, 65000 },
- { 0x00001105, 68179 },
- { 0x000031E4, 74250 },
- { 0x00003183, 75000 },
- { 0x00004284, 78750 },
- { 0x00001104, 81600 },
- { 0x00006363, 94500 },
- { 0x00005303, 97520 },
+ { 0x000131AC, 6231 },
+ { 0x0001215D, 6294 },
+ { 0x00011087, 6750 },
+ { 0x0001216C, 7081 },
+ { 0x0001218D, 7140 },
+ { 0x000110C9, 7800 },
+ { 0x00013147, 7875 },
+ { 0x000110A7, 8258 },
+ { 0x00012159, 8778 },
+ { 0x00014249, 8875 },
+ { 0x00010057, 9000 },
+ { 0x0001219A, 9472 },
+ { 0x00012158, 9792 },
+ { 0x00010045, 10000 },
+ { 0x00010089, 10791 },
+ { 0x000110E7, 11225 },
+ { 0x00012136, 11430 },
+ { 0x00013207, 12375 },
+ { 0x00012187, 12500 },
+ { 0x00014286, 14063 },
+ { 0x000110E5, 15016 },
+ { 0x00014214, 16250 },
+ { 0x00011105, 17045 },
+ { 0x000131E4, 18563 },
+ { 0x00013183, 18750 },
+ { 0x00014284, 19688 },
+ { 0x00011104, 20400 },
+ { 0x00016363, 23625 },
+ { 0x00015303, 24380 },
+ { 0x000031AC, 24923 },
+ { 0x0000215D, 25175 },
+ { 0x00001087, 27000 },
+ { 0x0000216C, 28322 },
+ { 0x0000218D, 28560 },
+ { 0x00010041, 29913 },
+ { 0x000010C9, 31200 },
+ { 0x00003147, 31500 },
+ { 0x000141A1, 32400 },
+ { 0x000010A7, 33032 },
+ { 0x00012182, 33375 },
+ { 0x000141B1, 33750 },
+ { 0x00002159, 35112 },
+ { 0x00004249, 35500 },
+ { 0x00000057, 36000 },
+ { 0x000141E1, 37125 },
+ { 0x0000219A, 37889 },
+ { 0x00002158, 39168 },
+ { 0x00000045, 40000 },
+ { 0x000131A1, 40500 },
+ { 0x00010061, 42301 },
+ { 0x00000089, 43163 },
+ { 0x00012151, 43875 },
+ { 0x000010E7, 44900 },
+ { 0x00002136, 45720 },
+ { 0x000152E1, 47250 },
+ { 0x00010071, 48000 },
+ { 0x00003207, 49500 },
+ { 0x00002187, 50000 },
+ { 0x00014291, 50625 },
+ { 0x00011101, 51188 },
+ { 0x00017481, 54563 },
+ { 0x00004286, 56250 },
+ { 0x00014170, 57375 },
+ { 0x00016210, 58500 },
+ { 0x000010E5, 60065 },
+ { 0x00013140, 62796 },
+ { 0x00004214, 65000 },
+ { 0x00016250, 65250 },
+ { 0x00001105, 68179 },
+ { 0x000141C0, 69600 },
+ { 0x00015220, 70160 },
+ { 0x00010050, 72000 },
+ { 0x000031E4, 74250 },
+ { 0x00003183, 75000 },
+ { 0x00004284, 78750 },
+ { 0x00012130, 80052 },
+ { 0x00001104, 81600 },
+ { 0x00006363, 94500 },
+ { 0x00005303, 97520 },
{ 0x00002183, 100187 },
{ 0x00002122, 101420 },
{ 0x00001081, 108000 },
@@ -137,7 +187,7 @@ static void lx_set_clock(struct fb_info
unsigned int diff, min, best = 0;
unsigned int freq, i;
- freq = (unsigned int) (0x3b9aca00 / info->var.pixclock);
+ freq = (unsigned int) (1000000000 / info->var.pixclock);
min = abs(pll_table[0].freq - freq);
@@ -149,7 +199,7 @@ static void lx_set_clock(struct fb_info
}
}
- lx_set_dotpll(pll_table[best].pllval & 0x7FFF);
+ lx_set_dotpll(pll_table[best].pllval & 0x00017FFF);
}
static void lx_graphics_disable(struct fb_info *info)
-------------------------------------------------------------------------
This SF.net email is sponsored by: Microsoft
Defy all challenges. Microsoft(R) Visual Studio 2008.
http://clk.atdmt.com/MRT/go/vse0120000070mrt/direct/01/
next reply other threads:[~2008-01-28 13:00 UTC|newest]
Thread overview: 2+ messages / expand[flat|nested] mbox.gz Atom feed top
2008-01-28 13:00 Jens Rottmann [this message]
-- strict thread matches above, loose matches on Subject: below --
2008-02-07 13:10 [PATCH] lxfb: extend PLL table to support dotclocks below 25 MHz Jens Rottmann
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=479DD1EB.2070202@LiPPERT-AT.de \
--to=jrottmann@lippert-at.de \
--cc=adaplas@gmail.com \
--cc=linux-fbdev-devel@lists.sourceforge.net \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.