From: "A. Nolson" <alohanono@gmail.com>
To: linuxppc-embedded@ozlabs.org
Subject: Problems booting in ML403
Date: Tue, 05 Feb 2008 15:52:30 +0100 [thread overview]
Message-ID: <47A8782E.4050402@gmail.com> (raw)
Hello,
I am having problems while trying to boot my linux kernel 2.6.24-rc3 (
secretlab git). After some days studying this list and other related
documents/wikis about how to make work a linux kernel in my ML403, I
managed to make it work partially.
I am using ELDK 4.1 "uclibc" as a cross compiler. I have also used ELDK
rootfs in my compactflash, when I boot it hangs at some point. This is
my console output:
loaded at: 00400000
005981A0
board data at: 00596124
005961A0
relocated to: 004040DC
00404158
zimage at: 00404ECD
00595EB8
avail ram: 00599000
04000000
Linux/PPC load: console=ttyS0,9600 console=tty0,9600 console=ttyUL0,9600
root=/d
ev/xsa2 rw
init=/sbin/init
Uncompressing
Linux...done.
Now booting the
kernel
[ 0.000000] Linux version 2.6.24-rc3-gd7ed933b-dirty (ios@xxx) (gcc vers
ion 4.0.0 (DENX ELDK 4.1 4.0.0)) #6 Mon Feb 4 14:06:43 CET
2008
[ 0.000000] Xilinx ML403 Reference System (Virtex-4
FX)
[ 0.000000] Zone PFN
ranges:
[ 0.000000] DMA 0 ->
16384
[ 0.000000] Normal 16384 ->
16384
[ 0.000000] HighMem 16384 ->
16384
[ 0.000000] Movable zone start PFN for each
node
[ 0.000000] early_node_map[1] active PFN
ranges
[ 0.000000] 0: 0 ->
16384
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on.
Total pag
es:
16256
[ 0.000000] Kernel command line: console=ttyS0,9600 console=tty0,9600
console
=ttyUL0,9600 root=/dev/xsa2 rw
init=/sbin/init
[ 0.000000] Xilinx INTC #0 at 0x41200000 mapped to
0xFDFFE000
[ 0.000000] PID hash table entries: 256 (order: 8, 1024
bytes)
[ 0.000449] Console: colour dummy device
80x25
[ 0.000546] console [tty0]
enabled
[ 0.002982] Dentry cache hash table entries: 8192 (order: 3, 32768
bytes)
[ 0.004906] Inode-cache hash table entries: 4096 (order: 2, 16384
bytes)
[ 0.038813] Memory: 61312k available (2740k kernel code, 784k data,
112k init
, 0k
highmem)
[ 0.039615] SLUB: Genslabs=11, HWalign=32, Order=0-1, MinObjects=4,
CPUs=1, N
odes=1
[ 0.220715] Mount-cache hash table entries:
512
[ 0.231019] net_namespace: 64
bytes
[ 0.244246] NET: Registered protocol family
16
[ 0.368073] NET: Registered protocol family
2
[ 0.461661] IP route cache hash table entries: 1024 (order: 0, 4096
bytes)
[ 0.467834] TCP established hash table entries: 2048 (order: 2, 16384
bytes)
[ 0.468813] TCP bind hash table entries: 2048 (order: 1, 8192
bytes)
[ 0.469483] TCP: Hash tables configured (established 2048 bind
2048)
[ 0.469711] TCP reno
registered
[ 0.493382] sysctl table check failed: /kernel/l2cr .1.31 Missing
strategy
[ 0.493825] Call
Trace:
[ 0.493957] [c3c11e80] [c0008380] show_stack+0x4c/0x174
(unreliable)
[ 0.494322] [c3c11eb0] [c0037170]
set_fail+0x50/0x68
[ 0.494637] [c3c11ed0] [c00377f8]
sysctl_check_table+0x670/0x6bc
[ 0.494922] [c3c11f10] [c003780c]
sysctl_check_table+0x684/0x6bc
[ 0.495203] [c3c11f50] [c0024e7c]
register_sysctl_table+0x5c/0xac
[ 0.495533] [c3c11f70] [c034ab68]
register_ppc_htab_sysctl+0x18/0x2c
[ 0.495864] [c3c11f80] [c034484c]
kernel_init+0xc8/0x284
[ 0.496130] [c3c11ff0] [c0004b18]
kernel_thread+0x44/0x60
[ 0.630804] Installing knfsd (copyright (C) 1996
okir@monad.swb.de).
[ 0.642747] JFS: nTxBlock = 479, nTxLock =
3832
[ 0.650497] SGI XFS with ACLs, large block numbers, no debug
enabled
[ 0.687400] io scheduler noop
registered
[ 0.687710] io scheduler anticipatory
registered
[ 0.687880] io scheduler deadline
registered
[ 0.689104] io scheduler cfq registered
(default)
[ 2.129848] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ
sharing
disabled
[ 2.150840] serial8250.0: ttyS0 at MMIO 0x40401003 (irq = 3) is a
16550A
[ 2.151248] console [ttyS0]
enabled
[ 5.425398] RAMDISK driver initialized: 16 RAM disks of 4096K size
1024 block
size
[ 5.532502] loop: module
loaded
[ 5.572824] xsysace xsysace.0: Xilinx SystemACE revision
1.0.12
[ 5.645558] xsysace xsysace.0: capacity: 1019088
sectors
[ 5.710732] xsa: xsa1 xsa2
xsa3
[ 5.763112] Xilinx SystemACE device driver,
major=254
[ 5.826421] nbd: registered device at major
43
[ 5.921820] XTemac: using sgDMA
mode.
[ 5.966225] XTemac: using TxDRE
mode
[ 6.009573] XTemac: using RxDRE
mode
[ 6.052783] XTemac: buffer descriptor size: 32768
(0x8000)
[ 6.120289] XTemac: (buffer_descriptor_init) phy: 0x3d80000, virt:
0xff100000
, size:
0x8000
[ 6.231949] eth%d: XTemac: No PHY detected. Assuming a PHY at
address 0
[ 6.313017] eth0: Dropping NETIF_F_SG since no checksum
feature.
[ 6.392778] eth0: Xilinx TEMAC #0 at 0x81200000 mapped to 0xC5060000,
irq=0
[ 6.476905] eth0: XTemac id 1.0f, block id 5, type
8
[ 6.539381] NFTL driver: nftlcore.c $Revision: 1.98 $, nftlmount.c
$Revision:
1.41
$
[ 6.633905] INFTL: inftlcore.c $Revision: 1.19 $, inftlmount.c
$Revision: 1.1
8
$
[ 6.725083] SSFDC read-only Flash Translation
layer
[ 6.791347] i8042.c: No controller
found.
[ 6.843298] mice: PS/2 mouse device common for all
mice
[ 6.912775] i2c /dev entries
driver
[ 6.958352] TCP cubic
registered
[ 6.998344] NET: Registered protocol family
1
[ 7.051264] NET: Registered protocol family
17
[ 7.110285] RPC: Registered udp transport
module.
[ 7.167370] RPC: Registered tcp transport
module.
[ 9.302726] kjournald starting. Commit interval 5
seconds
[ 9.408788] EXT3 FS on xsa2, internal
journal
[ 9.461599] EXT3-fs: recovery
complete.
[ 9.547744] EXT3-fs: mounted filesystem with ordered data
mode.
[ 9.619378] VFS: Mounted root (ext3
filesystem).
[ 9.675834] Freeing unused kernel memory: 112k
init
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
I actually had tried before with the original rootfs that comes with the
given montavista demo, and I got this:
(...)
[ 12.906329] kjournald starting. Commit interval 5 seconds
[ 12.972902] EXT3-fs warning: maximal mount count reached, running
e2fsck is r
ecommended
[ 13.109355] EXT3 FS on xsa2, internal
journal
[ 13.162196] EXT3-fs: recovery
complete.
[ 13.247717] EXT3-fs: mounted filesystem with ordered data
mode.
[ 13.319357] VFS: Mounted root (ext3
filesystem).
[ 13.375883] Freeing unused kernel memory: 112k
init
[ 13.441190] Warning: unable to open an initial
console.
[ 19.728949] eth0: XTemac: Options:
0xb8f2
[ 31.747487] eth0: XTemac: Not able to set the speed to 1000 (status:
0x148)
[ 41.806572] eth0: XTemac: Not able to set the speed to 100 (status:
0x148)
[ 51.864570] eth0: XTemac: Not able to set the speed to 10 (status:
0x148)
[ 51.946095] eth0: XTemac: could not negotiate
speed
[ 52.004713] eth0: XTemac: Send Threshold = 16, Receive Threshold =
2
[ 52.080998] eth0: XTemac: Send Wait bound = 1, Receive Wait bound =
1
[ 64.670479] eth0: XTemac: PHY Link carrier lost.
Stopping here. Any ideas? Is there a problem with my eldk rootfs?
Thanks in advance!
next reply other threads:[~2008-02-05 14:52 UTC|newest]
Thread overview: 3+ messages / expand[flat|nested] mbox.gz Atom feed top
2008-02-05 14:52 A. Nolson [this message]
2008-02-05 16:24 ` Problems booting in ML403 Grant Likely
2008-02-06 12:04 ` A. Nolson
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=47A8782E.4050402@gmail.com \
--to=alohanono@gmail.com \
--cc=linuxppc-embedded@ozlabs.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.