[Qemu-devel] [PATCH] Add serial loopback mode (+ fixes reset)

["Hervé Poussineau" <hpoussin@reactos.org>]

[-- Attachment #1: Type: text/plain, Size: 290 bytes --]

Hi,

Serial emulation lacks loopback mode (ie a transmitted byte is directly 
received in the serial port).

After a reset, serial port registers should go back to default values. 
This is done by adding a call to qemu_register_reset().

Attached patch fixes both issues.

Hervé

[-- Attachment #2: serial-loopback.patch --]
[-- Type: text/plain, Size: 2947 bytes --]

Index: hw/serial.c
===================================================================
RCS file: /sources/qemu/qemu/hw/serial.c,v
retrieving revision 1.22
diff -u -r1.22 serial.c
--- hw/serial.c	25 Nov 2007 00:55:06 -0000	1.22
+++ hw/serial.c	31 Jan 2008 16:51:19 -0000
@@ -93,6 +93,8 @@
     int it_shift;
 };
 
+static void serial_receive_byte(SerialState *s, int ch);
+
 static void serial_update_irq(SerialState *s)
 {
     if ((s->lsr & UART_LSR_DR) && (s->ier & UART_IER_RDI)) {
@@ -161,11 +163,18 @@
             s->lsr &= ~UART_LSR_THRE;
             serial_update_irq(s);
             ch = val;
-            qemu_chr_write(s->chr, &ch, 1);
+            if (!(s->mcr & UART_MCR_LOOP)) {
+                /* when not in loopback mode, send the char */
+                qemu_chr_write(s->chr, &ch, 1);
+            }
             s->thr_ipending = 1;
             s->lsr |= UART_LSR_THRE;
             s->lsr |= UART_LSR_TEMT;
             serial_update_irq(s);
+            if (s->mcr & UART_MCR_LOOP) {
+                /* in loopback mode, say that we just received a char */
+                serial_receive_byte(s, ch);
+            }
         }
         break;
     case 1:
@@ -223,7 +232,10 @@
             ret = s->rbr;
             s->lsr &= ~(UART_LSR_DR | UART_LSR_BI);
             serial_update_irq(s);
-            qemu_chr_accept_input(s->chr);
+            if (!(s->mcr & UART_MCR_LOOP)) {
+                /* in loopback mode, don't receive any data */
+                qemu_chr_accept_input(s->chr);
+            }
         }
         break;
     case 1:
@@ -346,6 +358,25 @@
     return 0;
 }
 
+static void serial_reset(void *opaque)
+{
+    SerialState *s = opaque;
+
+    s->divider = 0;
+    s->rbr = 0;
+    s->ier = 0;
+    s->iir = UART_IIR_NO_INT;
+    s->lcr = 0;
+    s->mcr = 0;
+    s->lsr = UART_LSR_TEMT | UART_LSR_THRE;
+    s->msr = UART_MSR_DCD | UART_MSR_DSR | UART_MSR_CTS;
+    s->scr = 0;
+
+    s->thr_ipending = 0;
+    s->last_break_enable = 0;
+    qemu_irq_lower(s->irq);
+}
+
 /* If fd is zero, it means that the serial device uses the console */
 SerialState *serial_init(int base, qemu_irq irq, CharDriverState *chr)
 {
@@ -355,9 +386,9 @@
     if (!s)
         return NULL;
     s->irq = irq;
-    s->lsr = UART_LSR_TEMT | UART_LSR_THRE;
-    s->iir = UART_IIR_NO_INT;
-    s->msr = UART_MSR_DCD | UART_MSR_DSR | UART_MSR_CTS;
+
+    qemu_register_reset(serial_reset, s);
+    serial_reset(s);
 
     register_savevm("serial", base, 2, serial_save, serial_load, s);
 
@@ -452,12 +483,12 @@
     if (!s)
         return NULL;
     s->irq = irq;
-    s->lsr = UART_LSR_TEMT | UART_LSR_THRE;
-    s->iir = UART_IIR_NO_INT;
-    s->msr = UART_MSR_DCD | UART_MSR_DSR | UART_MSR_CTS;
     s->base = base;
     s->it_shift = it_shift;
 
+    qemu_register_reset(serial_reset, s);
+    serial_reset(s);
+
     register_savevm("serial", base, 2, serial_save, serial_load, s);
 
     if (ioregister) {