From: Ivo Couckuyt <iv0co@yahoo.co.uk>
To: linux-wireless@vger.kernel.org
Subject: PROBLEM: p54usb doesn't work with my Philips CPWUA054 usb adapter
Date: Sun, 10 Feb 2008 23:25:30 +0100 [thread overview]
Message-ID: <47AF79DA.10204@yahoo.co.uk> (raw)
Hi,
I followed the guidelines for a bug report.
If there is anything else needed, I'll be happy to do all the testing
needed.
[1.] One line summary of the problem:
p54usb driver crashes on trying to associate with an ap with the
CPWUA054 usb adapter
[2.] Full description of the problem/report:
What works:
modprobe p54usb
dmesg (displays my adapter correctly)
ifconfig up wlan0
dmesg (using the right firmware 2.5.6.0)
but trying to associate to my accesspoint (using wpa_supplicant) causes
a hard-lock up (keyboard leds blinking).
Before locking up it spams loads of 'RX: unknown frame received phy1'
messages on kmsg/dmesg.
Note that my adapter isn't in the vendor:model id list of the p54
driver, my patch submitted for that is prob. lost somewhere.
But I'm using islsm with my usb adapters for >1.5 years with no problems.
lsusb lists my device's model/vendor id
Bus 001 Device 002: ID 083a:5501 Accton Technology Corp.
I also tried the wireless-2.6 kernel some months again with the same
issue, though I had some kernel option on that allowed
me to do a traceback to the failed function, *rx*() i believe (in p54
itself). I'm not really familiar with kernel debugging but i'll try
to give you the full trace in a couple of days, have to figure out how
to do it again.
If there is anything else that is useful, I'll be happy to provide it.
[3.] Keywords (i.e., modules, networking, kernel):
wireless, p54 driver
[4.] Kernel version (from /proc/version):
If some fields are empty or look unusual you may have an old version.
Compare to the current minimal requirements in Documentation/Changes.
Linux barton 2.6.24-gentoo-r2-BARTON #3 PREEMPT Tue Feb 19 20:31:03 CET
2008 i686 AMD Athlon(tm) XP 2500+ AuthenticAMD GNU/Linux
Gnu C 4.1.2
Gnu make 3.81
binutils 2.18
util-linux 2.12r
mount 2.12r
module-init-tools 3.2.2
e2fsprogs 1.40.2
PPP 2.4.4
Linux C Library 2.6.1
Dynamic linker (ldd) 2.6.1
Procps 3.2.7
Net-tools 1.60
Kbd 1.13
Sh-utils 6.9
udev 115
wireless-tools 29
Modules Loaded p54usb p54common firmware_class nvidia_agp
agpgart forcedeth
[5.] Output of Oops.. message (if applicable) with symbolic information
resolved (see Documentation/oops-tracing.txt)
[6.] A small shell script or example program which triggers the
problem (if possible)
/ Specific to hardware
[7.] Environment
/
[7.1.] Software (add the output of the ver_linux script here)
If some fields are empty or look unusual you may have an old version.
Compare to the current minimal requirements in Documentation/Changes.
Linux barton 2.6.24-gentoo-r2-BARTON #3 PREEMPT Tue Feb 19 20:31:03 CET
2008 i686 AMD Athlon(tm) XP 2500+ AuthenticAMD GNU/Linux
Gnu C 4.1.2
Gnu make 3.81
binutils 2.18
util-linux 2.12r
mount 2.12r
module-init-tools 3.2.2
e2fsprogs 1.40.2
PPP 2.4.4
Linux C Library 2.6.1
Dynamic linker (ldd) 2.6.1
Procps 3.2.7
Net-tools 1.60
Kbd 1.13
Sh-utils 6.9
udev 115
wireless-tools 29
Modules Loaded p54usb p54common firmware_class nvidia_agp
agpgart forcedeth
[7.2.] Processor information (from /proc/cpuinfo):
/
[7.3.] Module information (from /proc/modules):
p54usb 12672 0 - Live 0xf8828000
p54common 11136 1 p54usb, Live 0xf8817000
firmware_class 7424 1 p54usb, Live 0xf8814000
nvidia_agp 6428 1 - Live 0xf8825000
agpgart 27056 1 nvidia_agp, Live 0xf881d000
forcedeth 47372 0 - Live 0xf885e000
[7.4.] Loaded driver and hardware information (/proc/ioports, /proc/iomem)
[7.5.] PCI information ('lspci -vvv' as root)
00:00.0 Host bridge: nVidia Corporation nForce2 AGP (different version?)
(rev c1)
Subsystem: ASUSTeK Computer Inc. Unknown device 80ac
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Region 0: Memory at e0000000 (32-bit, prefetchable) [size=128M]
Capabilities: [40] AGP version 3.0
Status: RQ=32 Iso- ArqSz=2 Cal=0 SBA+ ITACoh- GART64- HTrans-
64bit- FW+ AGP3+ Rate=x4,x8
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=x4
Capabilities: [60] HyperTransport: Host or Secondary Interface
Command: WarmRst+ DblEnd-
Link Control: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0
Link Config: MLWI=8bit MLWO=8bit LWI=8bit LWO=8bit
Revision ID: 0.16
00:00.1 RAM memory: nVidia Corporation nForce2 Memory Controller 1 (rev c1)
Subsystem: ASUSTeK Computer Inc. Unknown device 80ac
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
00:00.2 RAM memory: nVidia Corporation nForce2 Memory Controller 4 (rev c1)
Subsystem: ASUSTeK Computer Inc. Unknown device 80ac
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
00:00.3 RAM memory: nVidia Corporation nForce2 Memory Controller 3 (rev c1)
Subsystem: ASUSTeK Computer Inc. Unknown device 80ac
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
00:00.4 RAM memory: nVidia Corporation nForce2 Memory Controller 2 (rev c1)
Subsystem: ASUSTeK Computer Inc. Unknown device 80ac
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
00:00.5 RAM memory: nVidia Corporation nForce2 Memory Controller 5 (rev c1)
Subsystem: ASUSTeK Computer Inc. Unknown device 80ac
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
00:01.0 ISA bridge: nVidia Corporation nForce2 ISA Bridge (rev a4)
Subsystem: ASUSTeK Computer Inc. A7N8X Mainboard
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: [48] HyperTransport: Slave or Primary Interface
Command: BaseUnitID=1 UnitCnt=15 MastHost- DefDir-
Link Control 0: CFlE- CST- CFE- <LkFail- Init+ EOC+ TXO- <CRCErr=0
Link Config 0: MLWI=8bit MLWO=8bit LWI=8bit LWO=8bit
Link Control 1: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO+ <CRCErr=0
Link Config 1: MLWI=8bit MLWO=8bit LWI=8bit LWO=8bit
Revision ID: 0.00
00:01.1 SMBus: nVidia Corporation nForce2 SMBus (MCP) (rev a2)
Subsystem: ASUSTeK Computer Inc. Unknown device 0c11
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 5
Region 0: I/O ports at c000 [size=32]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:02.0 USB Controller: nVidia Corporation nForce2 USB Controller (rev
a4) (prog-if 10 [OHCI])
Subsystem: ASUSTeK Computer Inc. A7N8X Mainboard
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin A routed to IRQ 11
Region 0: Memory at ea004000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:02.1 USB Controller: nVidia Corporation nForce2 USB Controller (rev
a4) (prog-if 10 [OHCI])
Subsystem: ASUSTeK Computer Inc. A7N8X Mainboard
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin B routed to IRQ 5
Region 0: Memory at ea005000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:02.2 USB Controller: nVidia Corporation nForce2 USB Controller (rev
a4) (prog-if 20 [EHCI])
Subsystem: ASUSTeK Computer Inc. A7N8X Mainboard
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin C routed to IRQ 11
Region 0: Memory at ea000000 (32-bit, non-prefetchable) [size=256]
Capabilities: [44] Debug port
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:04.0 Ethernet controller: nVidia Corporation nForce2 Ethernet
Controller (rev a1)
Subsystem: ASUSTeK Computer Inc. A7N8X Mainboard onboard nForce2
Ethernet
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (250ns min, 5000ns max)
Interrupt: pin A routed to IRQ 11
Region 0: Memory at ea001000 (32-bit, non-prefetchable) [size=4K]
Region 1: I/O ports at c400 [size=8]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable+ DSel=0 DScale=0 PME-
00:06.0 Multimedia audio controller: nVidia Corporation nForce2 AC97
Audio Controler (MCP) (rev a1)
Subsystem: ASUSTeK Computer Inc. nForce2 AC97 Audio Controler (MCP)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (500ns min, 1250ns max)
Interrupt: pin A routed to IRQ 5
Region 0: I/O ports at b000 [size=256]
Region 1: I/O ports at b400 [size=128]
Region 2: Memory at ea002000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:08.0 PCI bridge: nVidia Corporation nForce2 External PCI Bridge (rev
a3) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
I/O behind bridge: 00009000-00009fff
Memory behind bridge: fff00000-000fffff
Prefetchable memory behind bridge: fff00000-000fffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr+ DiscTmrStat- DiscTmrSERREn-
00:09.0 IDE interface: nVidia Corporation nForce2 IDE (rev a2) (prog-if
8a [Master SecP PriP])
Subsystem: ASUSTeK Computer Inc. Unknown device 0c11
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable)
[disabled] [size=8]
Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable)
[disabled] [size=1]
Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable)
[disabled] [size=8]
Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable)
[disabled] [size=1]
Region 4: I/O ports at f000 [size=16]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:1e.0 PCI bridge: nVidia Corporation nForce2 AGP (rev c1) (prog-if 00
[Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 240
Bus: primary=00, secondary=02, subordinate=02, sec-latency=32
I/O behind bridge: 0000a000-0000afff
Memory behind bridge: e8000000-e9ffffff
Prefetchable memory behind bridge: c0000000-dfffffff
Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
01:08.0 Multimedia audio controller: Creative Labs SB0400 Audigy2 Value
Subsystem: Creative Labs Unknown device 1021
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 240 (500ns min, 5000ns max)
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at 9000 [size=64]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
02:00.0 VGA compatible controller: ATI Technologies Inc RV350 AP [Radeon
9600] (prog-if 00 [VGA])
Subsystem: C.P. Technology Co. Ltd PowerColor R96A-C3N
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 255 (2000ns min), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 5
Region 0: Memory at c0000000 (32-bit, prefetchable) [size=256M]
Region 1: I/O ports at a000 [size=256]
Region 2: Memory at e9000000 (32-bit, non-prefetchable) [size=64K]
[virtual] Expansion ROM at e8000000 [disabled] [size=128K]
Capabilities: [58] AGP version 3.0
Status: RQ=256 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans-
64bit- FW+ AGP3+ Rate=x4,x8
Command: RQ=1 ArqSz=0 Cal=0 SBA+ AGP- GART64- 64bit- FW- Rate=<none>
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
02:00.1 Display controller: ATI Technologies Inc RV350 AP [Radeon 9600]
(Secondary)
Subsystem: C.P. Technology Co. Ltd Unknown device 2065
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Region 0: Memory at d0000000 (32-bit, prefetchable) [disabled]
[size=256M]
Region 1: Memory at e9010000 (32-bit, non-prefetchable) [disabled]
[size=64K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
[7.6.] SCSI information (from /proc/scsi/scsi)
[7.7.] Other information that might be relevant to the problem
(please look in /proc and include all information that you
think to be relevant):
[X.] Other notes, patches, fixes, workarounds:
kind regards,
Ivo
next reply other threads:[~2008-02-20 18:01 UTC|newest]
Thread overview: 13+ messages / expand[flat|nested] mbox.gz Atom feed top
2008-02-10 22:25 Ivo Couckuyt [this message]
2008-02-20 18:40 ` PROBLEM: p54usb doesn't work with my Philips CPWUA054 usb adapter Johannes Berg
2008-06-06 21:06 ` Ivo Couckuyt
2008-06-08 11:54 ` Johannes Berg
2008-06-08 20:03 ` Chr
2008-06-08 21:23 ` Ivo Couckuyt
2008-02-20 20:09 ` John W. Linville
2008-02-11 2:04 ` Ivo Couckuyt
-- strict thread matches above, loose matches on Subject: below --
2008-07-02 17:07 Ivo Couckuyt
2008-07-02 17:26 ` Chr
2008-07-02 20:31 ` Ivo Couckuyt
2008-07-04 17:56 ` Chr
2008-07-04 18:21 ` Alan Stern
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=47AF79DA.10204@yahoo.co.uk \
--to=iv0co@yahoo.co.uk \
--cc=linux-wireless@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.