From: James Courtier-Dutton <James@superbug.co.uk>
To: Takashi Iwai <tiwai@suse.de>
Cc: alsa-devel@alsa-project.org
Subject: Re: X-Fi support in ALSA.
Date: Tue, 11 Mar 2008 21:24:15 +0000 [thread overview]
Message-ID: <47D6F87F.6080809@superbug.co.uk> (raw)
In-Reply-To: <s5hlk4pb2qf.wl%tiwai@suse.de>
[-- Attachment #1: Type: text/plain, Size: 923 bytes --]
Takashi Iwai wrote:
> At Mon, 10 Mar 2008 20:20:48 +0000,
> James Courtier-Dutton wrote:
>> Hi,
>>
>> I have now had a chance to read some of the specs of the X-Fi cards.
>> aka. emu20k1.
>> It turns out that some of the X-Fi cards have a compatibility mode.
>> By default, they boot up in compatibility mode.
>> The interesting point is that this "compatibility mode" is in fact the
>> intel-HD standard so could use the intel-hda driver.
>> For one X-Fi card with IDs:
>> Device 1102:0009 Subsystem: 1102:0010
>> works a bit with the ALSA hda-intel driver.
>> So far, the off the shelf hda-intel driver, with simple PCIs adjustment,
>> works for the above card, but only sound capture works so far, so
>> probably some quirk would be needed.
>> This compatibility mode works with the Windows Vista UAA drivers.
>
> Could you show /proc/asound/card*/codec#* contents for HD-audio mode?
>
>
> Takashi
See attached
[-- Attachment #2: ca0110-codec.txt --]
[-- Type: text/plain, Size: 5843 bytes --]
# Codec: Generic 1102 ID a
# Address: 1
# Vendor Id: 0x1102000a
# Subsystem Id: 0x1462c320
# Revision Id: 0x100000
# No Modem Function Group found
# Default PCM:
# rates [0x160]: 44100 48000 96000
# bits [0xa]: 16 24
# formats [0x1]: PCM
# Default Amp-In caps: ofs=0x67, nsteps=0x73, stepsize=0x01, mute=0
# Default Amp-Out caps: ofs=0x67, nsteps=0x67, stepsize=0x01, mute=0
# GPIO: io=0, o=0, i=0, unsolicited=0, wake=0
# Node 0x02 [Audio Output] wcaps 0x5: Stereo Amp-Out
# Amp-Out caps: ofs=0x67, nsteps=0x7f, stepsize=0x01, mute=0
# Amp-Out vals: [0x53 0x53]
# Converter: stream=0, channel=0
# Node 0x03 [Audio Output] wcaps 0x5: Stereo Amp-Out
# Amp-Out caps: ofs=0x67, nsteps=0x7f, stepsize=0x01, mute=0
# Amp-Out vals: [0x67 0x67]
# Converter: stream=0, channel=0
# Node 0x04 [Audio Output] wcaps 0x5: Stereo Amp-Out
# Amp-Out caps: ofs=0x67, nsteps=0x7f, stepsize=0x01, mute=0
# Amp-Out vals: [0x67 0x67]
# Converter: stream=0, channel=0
# Node 0x05 [Audio Output] wcaps 0x5: Stereo Amp-Out
# Amp-Out caps: ofs=0x67, nsteps=0x7f, stepsize=0x01, mute=0
# Amp-Out vals: [0x67 0x67]
# Converter: stream=0, channel=0
# Node 0x06 [Audio Output] wcaps 0x5: Stereo Amp-Out
# Amp-Out caps: ofs=0x67, nsteps=0x7f, stepsize=0x01, mute=0
# Amp-Out vals: [0x67 0x67]
# Converter: stream=0, channel=0
# Node 0x07 [Audio Output] wcaps 0x205: Stereo Digital Amp-Out
# Amp-Out caps: ofs=0x67, nsteps=0x7f, stepsize=0x01, mute=0
# Amp-Out vals: [0x67 0x67]
# Converter: stream=0, channel=0
# Digital:
# Digital category: 0x0
# Node 0x08 [Audio Input] wcaps 0x100103: Stereo Amp-In
# Amp-In caps: ofs=0x67, nsteps=0x7f, stepsize=0x01, mute=0
# Amp-In vals: [0x0c 0x0c]
# Converter: stream=0, channel=0
# SDI-Select: 1
# Connection: 1
# 0x10
# Node 0x09 [Audio Input] wcaps 0x10010b: Stereo Amp-In
# Amp-In caps: ofs=0x67, nsteps=0x7f, stepsize=0x01, mute=0
# Amp-In vals: [0x67 0x67]
# Converter: stream=0, channel=0
# SDI-Select: 1
# Connection: 1
# 0x11
# Node 0x0a [Audio Input] wcaps 0x100303: Stereo Digital Amp-In
# Amp-In caps: ofs=0x67, nsteps=0x7f, stepsize=0x01, mute=0
# Amp-In vals: [0x67 0x67]
# Converter: stream=0, channel=0
# SDI-Select: 1
# Digital: Non-Audio Pro GenLevel
# Digital category: 0x60
# Connection: 1
# 0x13
# Node 0x0b [Pin Complex] wcaps 0x40018d: Stereo Amp-Out
# Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
# Amp-Out vals: [0x00 0x00]
# Pincap 0x0814: OUT Detect
# Pin Default 0x01014010: [Jack] Line Out at Ext Rear
# Conn = 1/8, Color = Green
# DefAssociation = 0x1, Sequence = 0x0
# Pin-ctls: 0x40: OUT
# Unsolicited: tag=00, enabled=0
# Connection: 1
# 0x02
# Node 0x0c [Pin Complex] wcaps 0x40018d: Stereo Amp-Out
# Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
# Amp-Out vals: [0x00 0x00]
# Pincap 0x0814: OUT Detect
# Pin Default 0x01016011: [Jack] Line Out at Ext Rear
# Conn = 1/8, Color = Orange
# DefAssociation = 0x1, Sequence = 0x1
# Pin-ctls: 0xc0: OUT HP
# Unsolicited: tag=00, enabled=0
# Connection: 1
# 0x03
# Node 0x0d [Pin Complex] wcaps 0x40018d: Stereo Amp-Out
# Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
# Amp-Out vals: [0x00 0x00]
# Pincap 0x0814: OUT Detect
# Pin Default 0x01011012: [Jack] Line Out at Ext Rear
# Conn = 1/8, Color = Black
# DefAssociation = 0x1, Sequence = 0x2
# Pin-ctls: 0xc0: OUT HP
# Unsolicited: tag=00, enabled=0
# Connection: 1
# 0x04
# Node 0x0e [Pin Complex] wcaps 0x40018d: Stereo Amp-Out
# Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
# Amp-Out vals: [0x00 0x00]
# Pincap 0x0814: OUT Detect
# Pin Default 0x01012014: [Jack] Line Out at Ext Rear
# Conn = 1/8, Color = Grey
# DefAssociation = 0x1, Sequence = 0x4
# Pin-ctls: 0xc0: OUT HP
# Unsolicited: tag=00, enabled=0
# Connection: 1
# 0x05
# Node 0x0f [Pin Complex] wcaps 0x40018d: Stereo Amp-Out
# Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
# Amp-Out vals: [0x00 0x00]
# Pincap 0x081c: OUT HP Detect
# Pin Default 0x02214020: [Jack] HP Out at Ext Front
# Conn = 1/8, Color = Green
# DefAssociation = 0x2, Sequence = 0x0
# Pin-ctls: 0xc0: OUT HP
# Unsolicited: tag=00, enabled=0
# Connection: 1
# 0x06
# Node 0x10 [Pin Complex] wcaps 0x40008b: Stereo Amp-In
# Amp-In caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
# Amp-In vals:
# Pincap 0x0824: IN Detect
# Pin Default 0x01813030: [Jack] Line In at Ext Rear
# Conn = 1/8, Color = Blue
# DefAssociation = 0x3, Sequence = 0x0
# Pin-ctls: 0x20: IN
# Unsolicited: tag=00, enabled=0
# Node 0x11 [Pin Complex] wcaps 0x40008b: Stereo Amp-In
# Amp-In caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
# Amp-In vals:
# Pincap 0x0824: IN Detect
# Pin Default 0x02a19040: [Jack] Mic at Ext Front
# Conn = 1/8, Color = Pink
# DefAssociation = 0x4, Sequence = 0x0
# Pin-ctls: 0xa0: IN HP
# Unsolicited: tag=00, enabled=0
# Node 0x12 [Pin Complex] wcaps 0x40038d: Stereo Digital Amp-Out
# Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
# Amp-Out vals: [0x00 0x00]
# Pincap 0x0810: OUT
# Pin Default 0x01452150: [Jack] SPDIF Out at Ext Rear
# Conn = Optical, Color = Grey
# DefAssociation = 0x5, Sequence = 0x0
# Misc = NO_PRESENCE
# Pin-ctls: 0xc0: OUT HP
# Unsolicited: tag=00, enabled=0
# Connection: 1
# 0x07
# Node 0x13 [Pin Complex] wcaps 0x40028b: Stereo Digital Amp-In
# Amp-In caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
# Amp-In vals:
# Pincap 0x0820: IN
# Pin Default 0x01c51160: [Jack] SPDIF In at Ext Rear
# Conn = Optical, Color = Black
# DefAssociation = 0x6, Sequence = 0x0
# Misc = NO_PRESENCE
# Pin-ctls: 0xa0: IN HP
# Unsolicited: tag=00, enabled=0
# Node 0x14 [Vendor Defined Widget] wcaps 0xf00080: Mono
# Unsolicited: tag=00, enabled=0
[-- Attachment #3: Type: text/plain, Size: 160 bytes --]
_______________________________________________
Alsa-devel mailing list
Alsa-devel@alsa-project.org
http://mailman.alsa-project.org/mailman/listinfo/alsa-devel
next prev parent reply other threads:[~2008-03-11 21:24 UTC|newest]
Thread overview: 6+ messages / expand[flat|nested] mbox.gz Atom feed top
2008-03-10 20:20 X-Fi support in ALSA James Courtier-Dutton
2008-03-11 17:16 ` Takashi Iwai
2008-03-11 21:24 ` James Courtier-Dutton [this message]
2008-09-18 15:42 ` Sean R Plantz
-- strict thread matches above, loose matches on Subject: below --
2008-03-10 23:49 Spike
2008-03-11 0:09 ` William Pitcock
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=47D6F87F.6080809@superbug.co.uk \
--to=james@superbug.co.uk \
--cc=alsa-devel@alsa-project.org \
--cc=tiwai@suse.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.