On Tue, Mar 18, 2008 at 9:14 AM, Andre Schwarz
<andre.schwarz@matrix-vision.de> wrote:
  

 I've read some discussions about the "interrupt-map" attribute of the pci
node. I tried to follow Ben and David in their explanations - obviously I
didn't really get it.
 Looks like there are a lot of people outside who need some enlightenment
... including me, of course.

 Maybe you can clarify this ?

 Taken from motionpro.dts ...

    

First, you also need to look at interrupt-map-mask to interpret these
values; from motionpro.dts:

interrupt-map-mask = <f800 0 0 7>;

which is applied to the unit interrupt specifier to figure out how to
map onto the interrupt controller.  The /size/ of this field is
obtained by adding #address-cells with #interrupt-cells. (3+1=4).

'f8' refers to the upper 5 bits of the interrupt identifier which is a
number from 0-31 which relates to the IDSEL line as you guessed.  The
'7' covers the lower 3 bits of the interrupt specifier which can be 1,
2, 3 or 4.

The 120 bits in the middle are irrelevant, so interrupt-map-mask
leaves them as zeros.

  

     interrupt-map = <c000 0 0 1 &mpc5200_pic 0 0 3 // 1st slot
                                  c000 0 0 2 &mpc5200_pic 1 1 3
                                  c000 0 0 3 &mpc5200_pic 1 2 3
                                  c000 0 0 4 &mpc5200_pic 1 3 3

                                  c800 0 0 1 &mpc5200_pic 1 1 3 // 2nd slot
                                  c800 0 0 2 &mpc5200_pic 1 2 3
                                  c800 0 0 3 &mpc5200_pic 1 3 3
                                  c800 0 0 4 &mpc5200_pic 0 0 3>;


 First parameter seems to be the slot number, i.e. IDSEL line of the PCI
device.
 How is this value coded ? Are these the bits 15..11 of the configuration
address ?
    

I don't remember how this is encoded.  On the lite5200, idsel is wired
to d0 and d1 for slots 1 and 2 respectively, yet these values suggest
slots 24 and 25.  I'll need to look at this again later.

  

 2nd + 3rd paramter : no clue ! can you explain ?
    

first 3 cells are the unit address and is #address-cells large.  Only
the first cell contains real data.

  

 4th : seem to be INT_A ... _D of a PCI device. Usually a device uses only
INT_A. Do we need 4 entries in any case ?
    

you only need entries for irq lines that are wired up.  If your board
does not wire up _B, _C and _D, then don't have an entry for them.
However, if they are wired up then you should describe them.

  

 5th : ok - parent pic
    

Correct.

  

 6th ... 8th  : IRQ representation of the parent pic, which gives :

     6th : 0=CRIT for irq0 pin, 1=MAIN for irq1..3 pins
     7th : irq number. 1 for the irq0 pin inside CRIT level. irq1..3 have
number 1..3 inside MAIN level.
     8th : should be 3 = "level low" which is default for PCI.
    

Correct.

There is also some good information here:
http://playground.sun.com/1275/practice/imap/imap0_9d.pdf

Cheers,
g.