From: Tejun Heo <htejun@gmail.com>
To: "Tvrtko A. Ursulin" <tvrtko@ursulin.net>
Cc: linux-ide@vger.kernel.org, linux-kernel@vger.kernel.org
Subject: Re: libata errors with smartctl on 2.6.24, WD3200AAKS and nVidia AHCI
Date: Sun, 13 Apr 2008 12:11:15 +0900 [thread overview]
Message-ID: <480179D3.8070707@gmail.com> (raw)
In-Reply-To: <200804092130.07149.tvrtko@ursulin.net>
Tvrtko A. Ursulin wrote:
> Hi all,
>
> When running smartctl to get the attributes readout libata seems to get
> really confused on my system. After a timeout it recovers without apparent
> ill-effect, but the reported values are complete rubbish. Unfortunately I don't
> remember if this is a regression or it was always like this..
>
> I have attached some data below, but if more is needed just shout!
>
> Regards,
>
> Tvrtko
>
> root@sol:~# uname -a
> Linux sol 2.6.24.3 #4 SMP PREEMPT Sat Mar 8 12:57:56 GMT 2008 x86_64 GNU/Linux
>
> root@sol:~# smartctl -A /dev/sda
> smartctl version 5.37 [x86_64-unknown-linux-gnu] Copyright (C) 2002-6 Bruce Allen
> Home page is http://smartmontools.sourceforge.net/
>
> === START OF READ SMART DATA SECTION ===
> SMART Attributes Data Structure revision number: 17018
> Vendor Specific SMART Attributes with Thresholds:
> ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
> 255 Unknown_Attribute 0x373f 200 016 063 Pre-fail Always In_the_past 69269232549888
> 45 Unknown_Attribute 0x4344 087 082 068 Old_age Offline - 61779704492097
> 51 Unknown_Attribute 0x0039 000 000 057 Pre-fail Offline FAILING_NOW 52987850404480
> 66 Unknown_Attribute 0x3231 048 068 049 Pre-fail Offline FAILING_NOW 55350388793431
> 48 Unknown_Attribute 0x4130 065 083 048 Old_age Offline - 71675860037707
> 32 Unknown_Attribute 0x2030 032 032 048 Old_age Offline FAILING_NOW 35322350018592
> 32 Unknown_Attribute 0x2020 032 032 032 Old_age Offline FAILING_NOW 550026354720
> 16 Unknown_Attribute 0x3f00 000 016 000 Old_age Offline FAILING_NOW 280379760114684
> 255 Unknown_Attribute 0x000f 000 007 015 Pre-fail Always FAILING_NOW 131943408599808
> 120 Unknown_Attribute 0x7800 000 000 000 Old_age Offline FAILING_NOW 0
> 64 Unknown_Attribute 0xfe00 001 000 000 Old_age Offline In_the_past 39030002838272
> 104 Unknown_Attribute 0x4174 188 035 116 Old_age Offline In_the_past 48379254046529
> 225 Load_Cycle_Count 0x484e 000 085 078 Old_age Always FAILING_NOW 86
> 144 Unknown_Attribute 0x0016 000 000 022 Old_age Always FAILING_NOW 0
>
>
>
> [ 7846.128079] ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
> [ 7846.128086] ata2.00: cmd b0/da:00:00:4f:c2/00:00:00:00:00/00 tag 0
> [ 7846.128087] res 40/00:01:b4:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout)
> [ 7846.128090] ata2.00: status: { DRDY }
> [ 7846.128096] ata2: hard resetting link
> [ 7846.735912] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
> [ 7846.760523] ata2.00: configured for UDMA/133
> [ 7846.760530] ata2: EH complete
> [ 7846.760546] sd 1:0:0:0: [sda] 625142448 512-byte hardware sectors (320073 MB)
> [ 7846.760556] sd 1:0:0:0: [sda] Write Protect is off
> [ 7846.760558] sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
> [ 7846.760571] sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
> [ 7852.748405] ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
> [ 7852.748412] ata2.00: cmd b0/d1:01:01:4f:c2/00:00:00:00:00/00 tag 0 pio 512 in
> [ 7852.748413] res 40/00:01:b4:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout)
> [ 7852.748416] ata2.00: status: { DRDY }
> [ 7852.748421] ata2: hard resetting link
> [ 7853.356244] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
> [ 7853.378276] ata2.00: configured for UDMA/133
> [ 7853.378284] ata2: EH complete
> [ 7853.378416] sd 1:0:0:0: [sda] 625142448 512-byte hardware sectors (320073 MB)
> [ 7853.378519] sd 1:0:0:0: [sda] Write Protect is off
> [ 7853.378521] sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
> [ 7853.378761] sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
>
> 00:0e.0 SATA controller: nVidia Corporation Unknown device 07f4 (rev a2) (prog-if 01 [AHCI 1.0])
> Subsystem: Giga-byte Technology Unknown device b002
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0 (750ns min, 250ns max)
> Interrupt: pin A routed to IRQ 316
> Region 0: I/O ports at 09f0 [size=8]
> Region 1: I/O ports at 0bf0 [size=4]
> Region 2: I/O ports at 0970 [size=8]
> Region 3: I/O ports at 0b70 [size=4]
> Region 4: I/O ports at dc00 [size=16]
> Region 5: Memory at e5104000 (32-bit, non-prefetchable) [size=8K]
> Capabilities: [44] Power Management version 2
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
> Capabilities: [8c] #12 [0010]
> Capabilities: [b0] Message Signalled Interrupts: Mask- 64bit+ Queue=0/3 Enable+
> Address: 00000000fee0100c Data: 4181
>
> root@sol:~# lsscsi
> [1:0:0:0] disk ATA WDC WD3200AAKS-0 12.0 /dev/sda
> [2:0:0:0] cd/dvd TSSTcorp CDDVDW SH-S203N SB01 /dev/scd0
>
>
> root@sol:~# lsmod | grep -e "a[th][ac]"
> ahci 27524 8
> ata_generic 6404 0
> libata 152048 2 ahci,ata_generic
> scsi_mod 152752 5 firewire_sbp2,sg,sr_mod,sd_mod,libata
Is auto spindown configured for the drive?
--
tejun
next prev parent reply other threads:[~2008-04-13 3:11 UTC|newest]
Thread overview: 9+ messages / expand[flat|nested] mbox.gz Atom feed top
2008-04-09 20:30 libata errors with smartctl on 2.6.24, WD3200AAKS and nVidia AHCI Tvrtko A. Ursulin
2008-04-13 3:11 ` Tejun Heo [this message]
2008-04-13 7:34 ` Tvrtko A. Ursulin
2008-04-15 3:10 ` Tejun Heo
2008-04-15 6:21 ` Tvrtko A. Ursulin
2008-05-14 5:44 ` Tejun Heo
2008-05-14 6:58 ` Tvrtko A. Ursulin
2008-05-14 7:29 ` Tejun Heo
-- strict thread matches above, loose matches on Subject: below --
2008-05-14 7:58 Erik Inge Bolsø
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=480179D3.8070707@gmail.com \
--to=htejun@gmail.com \
--cc=linux-ide@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=tvrtko@ursulin.net \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.