From: Brice Goglin <brice@myri.com>
To: Jeff Garzik <jeff@garzik.org>
Cc: netdev@vger.kernel.org
Subject: [PATCH 14/16] myri10ge: add multislices support
Date: Fri, 09 May 2008 02:21:49 +0200 [thread overview]
Message-ID: <4823991D.2090906@myri.com> (raw)
In-Reply-To: <482397A3.1050604@myri.com>
Add multi-slice/MSI-X support. By default, a single slice
(and the normal firmware) are used. To enable msi-x, multi-slice
mode, one must load the driver with myri10ge_max_slices set to
either -1, or something larger than 1.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Andrew Gallatin <gallatin@myri.com>
---
drivers/net/myri10ge/myri10ge.c | 684 +++++++++++++++++++++++++---------------
1 file changed, 442 insertions(+), 242 deletions(-)
Index: linux-2.6/drivers/net/myri10ge/myri10ge.c
===================================================================
--- linux-2.6.orig/drivers/net/myri10ge/myri10ge.c 2008-05-09 00:14:33.000000000 +0200
+++ linux-2.6/drivers/net/myri10ge/myri10ge.c 2008-05-09 00:15:17.000000000 +0200
@@ -185,11 +185,13 @@
dma_addr_t fw_stats_bus;
int watchdog_tx_done;
int watchdog_tx_req;
+ char irq_desc[32];
};
struct myri10ge_priv {
- struct myri10ge_slice_state ss;
+ struct myri10ge_slice_state *ss;
int tx_boundary; /* boundary transmits cannot cross */
+ int num_slices;
int running; /* running? */
int csum_flag; /* rx_csums? */
int small_bytes;
@@ -208,6 +210,8 @@
dma_addr_t cmd_bus;
struct pci_dev *pdev;
int msi_enabled;
+ int msix_enabled;
+ struct msix_entry *msix_vectors;
u32 link_state;
unsigned int rdma_tags_available;
int intr_coal_delay;
@@ -244,6 +248,8 @@
static char *myri10ge_fw_unaligned = "myri10ge_ethp_z8e.dat";
static char *myri10ge_fw_aligned = "myri10ge_eth_z8e.dat";
+static char *myri10ge_fw_rss_unaligned = "myri10ge_rss_ethp_z8e.dat";
+static char *myri10ge_fw_rss_aligned = "myri10ge_rss_eth_z8e.dat";
static char *myri10ge_fw_name = NULL;
module_param(myri10ge_fw_name, charp, S_IRUGO | S_IWUSR);
@@ -321,6 +327,14 @@
module_param(myri10ge_wcfifo, int, S_IRUGO);
MODULE_PARM_DESC(myri10ge_wcfifo, "Enable WC Fifo when WC is enabled");
+static int myri10ge_max_slices = 1;
+module_param(myri10ge_max_slices, int, S_IRUGO);
+MODULE_PARM_DESC(myri10ge_max_slices, "Max tx/rx queues");
+
+static int myri10ge_rss_hash = MXGEFW_RSS_HASH_TYPE_SRC_PORT;
+module_param(myri10ge_rss_hash, int, S_IRUGO);
+MODULE_PARM_DESC(myri10ge_rss_hash, "Type of RSS hashing to do");
+
#define MYRI10GE_FW_OFFSET 1024*1024
#define MYRI10GE_HIGHPART_TO_U32(X) \
(sizeof (X) == 8) ? ((u32)((u64)(X) >> 32)) : (0)
@@ -657,7 +671,7 @@
return 0;
}
-static int myri10ge_load_firmware(struct myri10ge_priv *mgp)
+static int myri10ge_load_firmware(struct myri10ge_priv *mgp, int adopt)
{
char __iomem *submit;
__be32 buf[16] __attribute__ ((__aligned__(8)));
@@ -667,6 +681,8 @@
size = 0;
status = myri10ge_load_hotplug_firmware(mgp, &size);
if (status) {
+ if (!adopt)
+ return status;
dev_warn(&mgp->pdev->dev, "hotplug firmware loading failed\n");
/* Do not attempt to adopt firmware if there
@@ -859,7 +875,8 @@
static int myri10ge_reset(struct myri10ge_priv *mgp)
{
struct myri10ge_cmd cmd;
- int status;
+ struct myri10ge_slice_state *ss;
+ int i, status;
size_t bytes;
/* try to send a reset command to the card to see if it
@@ -872,20 +889,74 @@
}
(void)myri10ge_dma_test(mgp, MXGEFW_DMA_TEST);
+ /*
+ * Use non-ndis mcp_slot (eg, 4 bytes total,
+ * no toeplitz hash value returned. Older firmware will
+ * not understand this command, but will use the correct
+ * sized mcp_slot, so we ignore error returns
+ */
+ cmd.data0 = MXGEFW_RSS_MCP_SLOT_TYPE_MIN;
+ (void)myri10ge_send_cmd(mgp, MXGEFW_CMD_SET_RSS_MCP_SLOT_TYPE, &cmd, 0);
/* Now exchange information about interrupts */
- bytes = mgp->max_intr_slots * sizeof(*mgp->ss.rx_done.entry);
- memset(mgp->ss.rx_done.entry, 0, bytes);
+ bytes = mgp->max_intr_slots * sizeof(*mgp->ss[0].rx_done.entry);
cmd.data0 = (u32) bytes;
status = myri10ge_send_cmd(mgp, MXGEFW_CMD_SET_INTRQ_SIZE, &cmd, 0);
- cmd.data0 = MYRI10GE_LOWPART_TO_U32(mgp->ss.rx_done.bus);
- cmd.data1 = MYRI10GE_HIGHPART_TO_U32(mgp->ss.rx_done.bus);
- status |= myri10ge_send_cmd(mgp, MXGEFW_CMD_SET_INTRQ_DMA, &cmd, 0);
+
+ /*
+ * Even though we already know how many slices are supported
+ * via myri10ge_probe_slices() MXGEFW_CMD_GET_MAX_RSS_QUEUES
+ * has magic side effects, and must be called after a reset.
+ * It must be called prior to calling any RSS related cmds,
+ * including assigning an interrupt queue for anything but
+ * slice 0. It must also be called *after*
+ * MXGEFW_CMD_SET_INTRQ_SIZE, since the intrq size is used by
+ * the firmware to compute offsets.
+ */
+
+ if (mgp->num_slices > 1) {
+
+ /* ask the maximum number of slices it supports */
+ status = myri10ge_send_cmd(mgp, MXGEFW_CMD_GET_MAX_RSS_QUEUES,
+ &cmd, 0);
+ if (status != 0) {
+ dev_err(&mgp->pdev->dev,
+ "failed to get number of slices\n");
+ }
+
+ /*
+ * MXGEFW_CMD_ENABLE_RSS_QUEUES must be called prior
+ * to setting up the interrupt queue DMA
+ */
+
+ cmd.data0 = mgp->num_slices;
+ cmd.data1 = 1; /* use MSI-X */
+ status = myri10ge_send_cmd(mgp, MXGEFW_CMD_ENABLE_RSS_QUEUES,
+ &cmd, 0);
+ if (status != 0) {
+ dev_err(&mgp->pdev->dev,
+ "failed to set number of slices\n");
+
+ return status;
+ }
+ }
+ for (i = 0; i < mgp->num_slices; i++) {
+ ss = &mgp->ss[i];
+ cmd.data0 = MYRI10GE_LOWPART_TO_U32(ss->rx_done.bus);
+ cmd.data1 = MYRI10GE_HIGHPART_TO_U32(ss->rx_done.bus);
+ cmd.data2 = i;
+ status |= myri10ge_send_cmd(mgp, MXGEFW_CMD_SET_INTRQ_DMA,
+ &cmd, 0);
+ };
status |=
myri10ge_send_cmd(mgp, MXGEFW_CMD_GET_IRQ_ACK_OFFSET, &cmd, 0);
- mgp->ss.irq_claim = (__iomem __be32 *) (mgp->sram + cmd.data0);
+ for (i = 0; i < mgp->num_slices; i++) {
+ ss = &mgp->ss[i];
+ ss->irq_claim =
+ (__iomem __be32 *) (mgp->sram + cmd.data0 + 8 * i);
+ }
status |= myri10ge_send_cmd(mgp, MXGEFW_CMD_GET_IRQ_DEASSERT_OFFSET,
&cmd, 0);
mgp->irq_deassert = (__iomem __be32 *) (mgp->sram + cmd.data0);
@@ -899,18 +970,25 @@
}
put_be32(htonl(mgp->intr_coal_delay), mgp->intr_coal_delay_ptr);
- memset(mgp->ss.rx_done.entry, 0, bytes);
-
/* reset mcp/driver shared state back to 0 */
- mgp->ss.tx.req = 0;
- mgp->ss.tx.done = 0;
- mgp->ss.tx.pkt_start = 0;
- mgp->ss.tx.pkt_done = 0;
- mgp->ss.rx_big.cnt = 0;
- mgp->ss.rx_small.cnt = 0;
- mgp->ss.rx_done.idx = 0;
- mgp->ss.rx_done.cnt = 0;
+
mgp->link_changes = 0;
+ for (i = 0; i < mgp->num_slices; i++) {
+ ss = &mgp->ss[i];
+
+ memset(ss->rx_done.entry, 0, bytes);
+ ss->tx.req = 0;
+ ss->tx.done = 0;
+ ss->tx.pkt_start = 0;
+ ss->tx.pkt_done = 0;
+ ss->rx_big.cnt = 0;
+ ss->rx_small.cnt = 0;
+ ss->rx_done.idx = 0;
+ ss->rx_done.cnt = 0;
+ ss->tx.wake_queue = 0;
+ ss->tx.stop_queue = 0;
+ }
+
status = myri10ge_update_mac_address(mgp, mgp->dev->dev_addr);
myri10ge_change_pause(mgp, mgp->pause);
myri10ge_set_multicast_list(mgp->dev);
@@ -1095,9 +1173,10 @@
rx_frags[0].size -= MXGEFW_PAD;
len -= MXGEFW_PAD;
lro_receive_frags(&ss->rx_done.lro_mgr, rx_frags,
- len, len,
/* opaque, will come back in get_frag_header */
+ len, len,
(void *)(__force unsigned long)csum, csum);
+
return 1;
}
@@ -1236,7 +1315,7 @@
static inline void myri10ge_check_statblock(struct myri10ge_priv *mgp)
{
- struct mcp_irq_data *stats = mgp->ss.fw_stats;
+ struct mcp_irq_data *stats = mgp->ss[0].fw_stats;
if (unlikely(stats->stats_updated)) {
unsigned link_up = ntohl(stats->link_up);
@@ -1302,6 +1381,13 @@
u32 send_done_count;
int i;
+ /* an interrupt on a non-zero slice is implicitly valid
+ * since MSI-X irqs are not shared */
+ if (ss != mgp->ss) {
+ netif_rx_schedule(ss->dev, &ss->napi);
+ return (IRQ_HANDLED);
+ }
+
/* make sure it is our IRQ, and that the DMA has finished */
if (unlikely(!stats->valid))
return (IRQ_NONE);
@@ -1311,7 +1397,7 @@
if (stats->valid & 1)
netif_rx_schedule(ss->dev, &ss->napi);
- if (!mgp->msi_enabled) {
+ if (!mgp->msi_enabled && !mgp->msix_enabled) {
put_be32(0, mgp->irq_deassert);
if (!myri10ge_deassert_wait)
stats->valid = 0;
@@ -1446,10 +1532,10 @@
{
struct myri10ge_priv *mgp = netdev_priv(netdev);
- ring->rx_mini_max_pending = mgp->ss.rx_small.mask + 1;
- ring->rx_max_pending = mgp->ss.rx_big.mask + 1;
+ ring->rx_mini_max_pending = mgp->ss[0].rx_small.mask + 1;
+ ring->rx_max_pending = mgp->ss[0].rx_big.mask + 1;
ring->rx_jumbo_max_pending = 0;
- ring->tx_max_pending = mgp->ss.rx_small.mask + 1;
+ ring->tx_max_pending = mgp->ss[0].rx_small.mask + 1;
ring->rx_mini_pending = ring->rx_mini_max_pending;
ring->rx_pending = ring->rx_max_pending;
ring->rx_jumbo_pending = ring->rx_jumbo_max_pending;
@@ -1497,7 +1583,7 @@
"tx_aborted_errors", "tx_carrier_errors", "tx_fifo_errors",
"tx_heartbeat_errors", "tx_window_errors",
/* device-specific stats */
- "tx_boundary", "WC", "irq", "MSI",
+ "tx_boundary", "WC", "irq", "MSI", "MSIX",
"read_dma_bw_MBs", "write_dma_bw_MBs", "read_write_dma_bw_MBs",
"serial_number", "watchdog_resets",
"link_changes", "link_up", "dropped_link_overflow",
@@ -1524,23 +1610,31 @@
static void
myri10ge_get_strings(struct net_device *netdev, u32 stringset, u8 * data)
{
+ struct myri10ge_priv *mgp = netdev_priv(netdev);
+ int i;
+
switch (stringset) {
case ETH_SS_STATS:
memcpy(data, *myri10ge_gstrings_main_stats,
sizeof(myri10ge_gstrings_main_stats));
data += sizeof(myri10ge_gstrings_main_stats);
- memcpy(data, *myri10ge_gstrings_slice_stats,
- sizeof(myri10ge_gstrings_slice_stats));
- data += sizeof(myri10ge_gstrings_slice_stats);
+ for (i = 0; i < mgp->num_slices; i++) {
+ memcpy(data, *myri10ge_gstrings_slice_stats,
+ sizeof(myri10ge_gstrings_slice_stats));
+ data += sizeof(myri10ge_gstrings_slice_stats);
+ }
break;
}
}
static int myri10ge_get_sset_count(struct net_device *netdev, int sset)
{
+ struct myri10ge_priv *mgp = netdev_priv(netdev);
+
switch (sset) {
case ETH_SS_STATS:
- return MYRI10GE_MAIN_STATS_LEN + MYRI10GE_SLICE_STATS_LEN;
+ return MYRI10GE_MAIN_STATS_LEN +
+ mgp->num_slices * MYRI10GE_SLICE_STATS_LEN;
default:
return -EOPNOTSUPP;
}
@@ -1552,6 +1646,7 @@
{
struct myri10ge_priv *mgp = netdev_priv(netdev);
struct myri10ge_slice_state *ss;
+ int slice;
int i;
for (i = 0; i < MYRI10GE_NET_STATS_LEN; i++)
@@ -1561,6 +1656,7 @@
data[i++] = (unsigned int)mgp->wc_enabled;
data[i++] = (unsigned int)mgp->pdev->irq;
data[i++] = (unsigned int)mgp->msi_enabled;
+ data[i++] = (unsigned int)mgp->msix_enabled;
data[i++] = (unsigned int)mgp->read_dma;
data[i++] = (unsigned int)mgp->write_dma;
data[i++] = (unsigned int)mgp->read_write_dma;
@@ -1569,7 +1665,7 @@
data[i++] = (unsigned int)mgp->link_changes;
/* firmware stats are useful only in the first slice */
- ss = &mgp->ss;
+ ss = &mgp->ss[0];
data[i++] = (unsigned int)ntohl(ss->fw_stats->link_up);
data[i++] = (unsigned int)ntohl(ss->fw_stats->dropped_link_overflow);
data[i++] =
@@ -1585,24 +1681,27 @@
data[i++] = (unsigned int)ntohl(ss->fw_stats->dropped_no_small_buffer);
data[i++] = (unsigned int)ntohl(ss->fw_stats->dropped_no_big_buffer);
- data[i++] = 0;
- data[i++] = (unsigned int)ss->tx.pkt_start;
- data[i++] = (unsigned int)ss->tx.pkt_done;
- data[i++] = (unsigned int)ss->tx.req;
- data[i++] = (unsigned int)ss->tx.done;
- data[i++] = (unsigned int)ss->rx_small.cnt;
- data[i++] = (unsigned int)ss->rx_big.cnt;
- data[i++] = (unsigned int)ss->tx.wake_queue;
- data[i++] = (unsigned int)ss->tx.stop_queue;
- data[i++] = (unsigned int)ss->tx.linearized;
- data[i++] = ss->rx_done.lro_mgr.stats.aggregated;
- data[i++] = ss->rx_done.lro_mgr.stats.flushed;
- if (ss->rx_done.lro_mgr.stats.flushed)
- data[i++] = ss->rx_done.lro_mgr.stats.aggregated /
- ss->rx_done.lro_mgr.stats.flushed;
- else
- data[i++] = 0;
- data[i++] = ss->rx_done.lro_mgr.stats.no_desc;
+ for (slice = 0; slice < mgp->num_slices; slice++) {
+ ss = &mgp->ss[slice];
+ data[i++] = slice;
+ data[i++] = (unsigned int)ss->tx.pkt_start;
+ data[i++] = (unsigned int)ss->tx.pkt_done;
+ data[i++] = (unsigned int)ss->tx.req;
+ data[i++] = (unsigned int)ss->tx.done;
+ data[i++] = (unsigned int)ss->rx_small.cnt;
+ data[i++] = (unsigned int)ss->rx_big.cnt;
+ data[i++] = (unsigned int)ss->tx.wake_queue;
+ data[i++] = (unsigned int)ss->tx.stop_queue;
+ data[i++] = (unsigned int)ss->tx.linearized;
+ data[i++] = ss->rx_done.lro_mgr.stats.aggregated;
+ data[i++] = ss->rx_done.lro_mgr.stats.flushed;
+ if (ss->rx_done.lro_mgr.stats.flushed)
+ data[i++] = ss->rx_done.lro_mgr.stats.aggregated /
+ ss->rx_done.lro_mgr.stats.flushed;
+ else
+ data[i++] = 0;
+ data[i++] = ss->rx_done.lro_mgr.stats.no_desc;
+ }
}
static void myri10ge_set_msglevel(struct net_device *netdev, u32 value)
@@ -1645,12 +1744,15 @@
struct net_device *dev = mgp->dev;
int tx_ring_size, rx_ring_size;
int tx_ring_entries, rx_ring_entries;
- int i, status;
+ int i, slice, status;
size_t bytes;
/* get ring sizes */
+ slice = ss - mgp->ss;
+ cmd.data0 = slice;
status = myri10ge_send_cmd(mgp, MXGEFW_CMD_GET_SEND_RING_SIZE, &cmd, 0);
tx_ring_size = cmd.data0;
+ cmd.data0 = slice;
status |= myri10ge_send_cmd(mgp, MXGEFW_CMD_GET_RX_RING_SIZE, &cmd, 0);
if (status != 0)
return status;
@@ -1715,15 +1817,17 @@
mgp->small_bytes + MXGEFW_PAD, 0);
if (ss->rx_small.fill_cnt < ss->rx_small.mask + 1) {
- printk(KERN_ERR "myri10ge: %s: alloced only %d small bufs\n",
- dev->name, ss->rx_small.fill_cnt);
+ printk(KERN_ERR
+ "myri10ge: %s:slice-%d: alloced only %d small bufs\n",
+ dev->name, slice, ss->rx_small.fill_cnt);
goto abort_with_rx_small_ring;
}
myri10ge_alloc_rx_pages(mgp, &ss->rx_big, mgp->big_bytes, 0);
if (ss->rx_big.fill_cnt < ss->rx_big.mask + 1) {
- printk(KERN_ERR "myri10ge: %s: alloced only %d big bufs\n",
- dev->name, ss->rx_big.fill_cnt);
+ printk(KERN_ERR
+ "myri10ge: %s:slice-%d: alloced only %d big bufs\n",
+ dev->name, slice, ss->rx_big.fill_cnt);
goto abort_with_rx_big_ring;
}
@@ -1775,6 +1879,10 @@
struct myri10ge_tx_buf *tx;
int i, len, idx;
+ /* If not allocated, skip it */
+ if (ss->tx.req_list == NULL)
+ return;
+
for (i = ss->rx_big.cnt; i < ss->rx_big.fill_cnt; i++) {
idx = i & ss->rx_big.mask;
if (i == ss->rx_big.fill_cnt - 1)
@@ -1837,25 +1945,67 @@
static int myri10ge_request_irq(struct myri10ge_priv *mgp)
{
struct pci_dev *pdev = mgp->pdev;
+ struct myri10ge_slice_state *ss;
+ struct net_device *netdev = mgp->dev;
+ int i;
int status;
+ mgp->msi_enabled = 0;
+ mgp->msix_enabled = 0;
+ status = 0;
if (myri10ge_msi) {
- status = pci_enable_msi(pdev);
- if (status != 0)
- dev_err(&pdev->dev,
- "Error %d setting up MSI; falling back to xPIC\n",
- status);
- else
- mgp->msi_enabled = 1;
- } else {
- mgp->msi_enabled = 0;
+ if (mgp->num_slices > 1) {
+ status =
+ pci_enable_msix(pdev, mgp->msix_vectors,
+ mgp->num_slices);
+ if (status == 0) {
+ mgp->msix_enabled = 1;
+ } else {
+ dev_err(&pdev->dev,
+ "Error %d setting up MSI-X\n", status);
+ return status;
+ }
+ }
+ if (mgp->msix_enabled == 0) {
+ status = pci_enable_msi(pdev);
+ if (status != 0) {
+ dev_err(&pdev->dev,
+ "Error %d setting up MSI; falling back to xPIC\n",
+ status);
+ } else {
+ mgp->msi_enabled = 1;
+ }
+ }
}
- status = request_irq(pdev->irq, myri10ge_intr, IRQF_SHARED,
- mgp->dev->name, mgp);
- if (status != 0) {
- dev_err(&pdev->dev, "failed to allocate IRQ\n");
- if (mgp->msi_enabled)
- pci_disable_msi(pdev);
+ if (mgp->msix_enabled) {
+ for (i = 0; i < mgp->num_slices; i++) {
+ ss = &mgp->ss[i];
+ snprintf(ss->irq_desc, sizeof(ss->irq_desc),
+ "%s:slice-%d", netdev->name, i);
+ status = request_irq(mgp->msix_vectors[i].vector,
+ myri10ge_intr, 0, ss->irq_desc,
+ ss);
+ if (status != 0) {
+ dev_err(&pdev->dev,
+ "slice %d failed to allocate IRQ\n", i);
+ i--;
+ while (i >= 0) {
+ free_irq(mgp->msix_vectors[i].vector,
+ &mgp->ss[i]);
+ i--;
+ }
+ pci_disable_msix(pdev);
+ return status;
+ }
+ }
+ } else {
+ status = request_irq(pdev->irq, myri10ge_intr, IRQF_SHARED,
+ mgp->dev->name, &mgp->ss[0]);
+ if (status != 0) {
+ dev_err(&pdev->dev, "failed to allocate IRQ\n");
+ if (mgp->msi_enabled)
+ pci_disable_msi(pdev);
+ }
}
return status;
}
@@ -1863,10 +2013,18 @@
static void myri10ge_free_irq(struct myri10ge_priv *mgp)
{
struct pci_dev *pdev = mgp->pdev;
+ int i;
- free_irq(pdev->irq, mgp);
+ if (mgp->msix_enabled) {
+ for (i = 0; i < mgp->num_slices; i++)
+ free_irq(mgp->msix_vectors[i].vector, &mgp->ss[i]);
+ } else {
+ free_irq(pdev->irq, &mgp->ss[0]);
+ }
if (mgp->msi_enabled)
pci_disable_msi(pdev);
+ if (mgp->msix_enabled)
+ pci_disable_msix(pdev);
}
static int
@@ -1928,7 +2086,6 @@
return 0;
}
-#if 0
static int myri10ge_get_txrx(struct myri10ge_priv *mgp, int slice)
{
struct myri10ge_cmd cmd;
@@ -1996,14 +2153,15 @@
}
return 0;
}
-#endif
static int myri10ge_open(struct net_device *dev)
{
+ struct myri10ge_slice_state *ss;
struct myri10ge_priv *mgp = netdev_priv(dev);
struct myri10ge_cmd cmd;
+ int i, status, big_pow2, slice;
+ u8 *itable;
struct net_lro_mgr *lro_mgr;
- int status, big_pow2;
if (mgp->running != MYRI10GE_ETH_STOPPED)
return -EBUSY;
@@ -2015,6 +2173,48 @@
goto abort_with_nothing;
}
+ if (mgp->num_slices > 1) {
+ cmd.data0 = mgp->num_slices;
+ cmd.data1 = 1; /* use MSI-X */
+ status = myri10ge_send_cmd(mgp, MXGEFW_CMD_ENABLE_RSS_QUEUES,
+ &cmd, 0);
+ if (status != 0) {
+ printk(KERN_ERR
+ "myri10ge: %s: failed to set number of slices\n",
+ dev->name);
+ goto abort_with_nothing;
+ }
+ /* setup the indirection table */
+ cmd.data0 = mgp->num_slices;
+ status = myri10ge_send_cmd(mgp, MXGEFW_CMD_SET_RSS_TABLE_SIZE,
+ &cmd, 0);
+
+ status |= myri10ge_send_cmd(mgp,
+ MXGEFW_CMD_GET_RSS_TABLE_OFFSET,
+ &cmd, 0);
+ if (status != 0) {
+ printk(KERN_ERR
+ "myri10ge: %s: failed to setup rss tables\n",
+ dev->name);
+ }
+
+ /* just enable an identity mapping */
+ itable = mgp->sram + cmd.data0;
+ for (i = 0; i < mgp->num_slices; i++)
+ __raw_writeb(i, &itable[i]);
+
+ cmd.data0 = 1;
+ cmd.data1 = myri10ge_rss_hash;
+ status = myri10ge_send_cmd(mgp, MXGEFW_CMD_SET_RSS_ENABLE,
+ &cmd, 0);
+ if (status != 0) {
+ printk(KERN_ERR
+ "myri10ge: %s: failed to enable slices\n",
+ dev->name);
+ goto abort_with_nothing;
+ }
+ }
+
status = myri10ge_request_irq(mgp);
if (status != 0)
goto abort_with_nothing;
@@ -2038,41 +2238,6 @@
if (myri10ge_small_bytes > 0)
mgp->small_bytes = myri10ge_small_bytes;
- /* get the lanai pointers to the send and receive rings */
-
- status |= myri10ge_send_cmd(mgp, MXGEFW_CMD_GET_SEND_OFFSET, &cmd, 0);
- mgp->ss.tx.lanai =
- (struct mcp_kreq_ether_send __iomem *)(mgp->sram + cmd.data0);
-
- status |=
- myri10ge_send_cmd(mgp, MXGEFW_CMD_GET_SMALL_RX_OFFSET, &cmd, 0);
- mgp->ss.rx_small.lanai =
- (struct mcp_kreq_ether_recv __iomem *)(mgp->sram + cmd.data0);
-
- status |= myri10ge_send_cmd(mgp, MXGEFW_CMD_GET_BIG_RX_OFFSET, &cmd, 0);
- mgp->ss.rx_big.lanai =
- (struct mcp_kreq_ether_recv __iomem *)(mgp->sram + cmd.data0);
-
- if (status != 0) {
- printk(KERN_ERR
- "myri10ge: %s: failed to get ring sizes or locations\n",
- dev->name);
- mgp->running = MYRI10GE_ETH_STOPPED;
- goto abort_with_irq;
- }
-
- if (myri10ge_wcfifo && mgp->wc_enabled) {
- mgp->ss.tx.wc_fifo = (u8 __iomem *) mgp->sram + MXGEFW_ETH_SEND_4;
- mgp->ss.rx_small.wc_fifo =
- (u8 __iomem *) mgp->sram + MXGEFW_ETH_RECV_SMALL;
- mgp->ss.rx_big.wc_fifo =
- (u8 __iomem *) mgp->sram + MXGEFW_ETH_RECV_BIG;
- } else {
- mgp->ss.tx.wc_fifo = NULL;
- mgp->ss.rx_small.wc_fifo = NULL;
- mgp->ss.rx_big.wc_fifo = NULL;
- }
-
/* Firmware needs the big buff size as a power of 2. Lie and
* tell him the buffer is larger, because we only use 1
* buffer/pkt, and the mtu will prevent overruns.
@@ -2087,9 +2252,44 @@
mgp->big_bytes = big_pow2;
}
- status = myri10ge_allocate_rings(&mgp->ss);
- if (status != 0)
- goto abort_with_irq;
+ /* setup the per-slice data structures */
+ for (slice = 0; slice < mgp->num_slices; slice++) {
+ ss = &mgp->ss[slice];
+
+ status = myri10ge_get_txrx(mgp, slice);
+ if (status != 0) {
+ printk(KERN_ERR
+ "myri10ge: %s: failed to get ring sizes or locations\n",
+ dev->name);
+ goto abort_with_rings;
+ }
+ status = myri10ge_allocate_rings(ss);
+ if (status != 0)
+ goto abort_with_rings;
+ if (slice == 0)
+ status = myri10ge_set_stats(mgp, slice);
+ if (status) {
+ printk(KERN_ERR
+ "myri10ge: %s: Couldn't set stats DMA\n",
+ dev->name);
+ goto abort_with_rings;
+ }
+
+ lro_mgr = &ss->rx_done.lro_mgr;
+ lro_mgr->dev = dev;
+ lro_mgr->features = LRO_F_NAPI;
+ lro_mgr->ip_summed = CHECKSUM_COMPLETE;
+ lro_mgr->ip_summed_aggr = CHECKSUM_UNNECESSARY;
+ lro_mgr->max_desc = MYRI10GE_MAX_LRO_DESCRIPTORS;
+ lro_mgr->lro_arr = ss->rx_done.lro_desc;
+ lro_mgr->get_frag_header = myri10ge_get_frag_header;
+ lro_mgr->max_aggr = myri10ge_lro_max_pkts;
+ if (lro_mgr->max_aggr > MAX_SKB_FRAGS)
+ lro_mgr->max_aggr = MAX_SKB_FRAGS;
+
+ /* must happen prior to any irq */
+ napi_enable(&(ss)->napi);
+ }
/* now give firmware buffers sizes, and MTU */
cmd.data0 = dev->mtu + ETH_HLEN + VLAN_HLEN;
@@ -2106,25 +2306,15 @@
goto abort_with_rings;
}
- cmd.data0 = MYRI10GE_LOWPART_TO_U32(mgp->ss.fw_stats_bus);
- cmd.data1 = MYRI10GE_HIGHPART_TO_U32(mgp->ss.fw_stats_bus);
- cmd.data2 = sizeof(struct mcp_irq_data);
- status = myri10ge_send_cmd(mgp, MXGEFW_CMD_SET_STATS_DMA_V2, &cmd, 0);
- if (status == -ENOSYS) {
- dma_addr_t bus = mgp->ss.fw_stats_bus;
- bus += offsetof(struct mcp_irq_data, send_done_count);
- cmd.data0 = MYRI10GE_LOWPART_TO_U32(bus);
- cmd.data1 = MYRI10GE_HIGHPART_TO_U32(bus);
- status = myri10ge_send_cmd(mgp,
- MXGEFW_CMD_SET_STATS_DMA_OBSOLETE,
- &cmd, 0);
- /* Firmware cannot support multicast without STATS_DMA_V2 */
- mgp->fw_multicast_support = 0;
- } else {
- mgp->fw_multicast_support = 1;
- }
- if (status) {
- printk(KERN_ERR "myri10ge: %s: Couldn't set stats DMA\n",
+ /*
+ * Set Linux style TSO mode; this is needed only on newer
+ * firmware versions. Older versions default to Linux
+ * style TSO
+ */
+ cmd.data0 = 0;
+ status = myri10ge_send_cmd(mgp, MXGEFW_CMD_SET_TSO_MODE, &cmd, 0);
+ if (status && status != -ENOSYS) {
+ printk(KERN_ERR "myri10ge: %s: Couldn't set TSO mode\n",
dev->name);
goto abort_with_rings;
}
@@ -2132,21 +2322,6 @@
mgp->link_state = ~0U;
mgp->rdma_tags_available = 15;
- lro_mgr = &mgp->ss.rx_done.lro_mgr;
- lro_mgr->dev = dev;
- lro_mgr->features = LRO_F_NAPI;
- lro_mgr->ip_summed = CHECKSUM_COMPLETE;
- lro_mgr->ip_summed_aggr = CHECKSUM_UNNECESSARY;
- lro_mgr->max_desc = MYRI10GE_MAX_LRO_DESCRIPTORS;
- lro_mgr->lro_arr = mgp->ss.rx_done.lro_desc;
- lro_mgr->get_frag_header = myri10ge_get_frag_header;
- lro_mgr->max_aggr = myri10ge_lro_max_pkts;
- lro_mgr->frag_align_pad = 2;
- if (lro_mgr->max_aggr > MAX_SKB_FRAGS)
- lro_mgr->max_aggr = MAX_SKB_FRAGS;
-
- napi_enable(&mgp->ss.napi); /* must happen prior to any irq */
-
status = myri10ge_send_cmd(mgp, MXGEFW_CMD_ETHERNET_UP, &cmd, 0);
if (status) {
printk(KERN_ERR "myri10ge: %s: Couldn't bring up link\n",
@@ -2154,8 +2329,6 @@
goto abort_with_rings;
}
- mgp->ss.tx.wake_queue = 0;
- mgp->ss.tx.stop_queue = 0;
mgp->running = MYRI10GE_ETH_RUNNING;
mgp->watchdog_timer.expires = jiffies + myri10ge_watchdog_timeout * HZ;
add_timer(&mgp->watchdog_timer);
@@ -2163,9 +2336,9 @@
return 0;
abort_with_rings:
- myri10ge_free_rings(&mgp->ss);
+ for (i = 0; i < mgp->num_slices; i++)
+ myri10ge_free_rings(&mgp->ss[i]);
-abort_with_irq:
myri10ge_free_irq(mgp);
abort_with_nothing:
@@ -2178,16 +2351,19 @@
struct myri10ge_priv *mgp = netdev_priv(dev);
struct myri10ge_cmd cmd;
int status, old_down_cnt;
+ int i;
if (mgp->running != MYRI10GE_ETH_RUNNING)
return 0;
- if (mgp->ss.tx.req_bytes == NULL)
+ if (mgp->ss[0].tx.req_bytes == NULL)
return 0;
del_timer_sync(&mgp->watchdog_timer);
mgp->running = MYRI10GE_ETH_STOPPING;
- napi_disable(&mgp->ss.napi);
+ for (i = 0; i < mgp->num_slices; i++) {
+ napi_disable(&mgp->ss[i].napi);
+ }
netif_carrier_off(dev);
netif_stop_queue(dev);
old_down_cnt = mgp->down_cnt;
@@ -2203,7 +2379,8 @@
netif_tx_disable(dev);
myri10ge_free_irq(mgp);
- myri10ge_free_rings(&mgp->ss);
+ for (i = 0; i < mgp->num_slices; i++)
+ myri10ge_free_rings(&mgp->ss[i]);
mgp->running = MYRI10GE_ETH_STOPPED;
return 0;
@@ -2324,7 +2501,7 @@
u8 flags, odd_flag;
/* always transmit through slot 0 */
- ss = &mgp->ss;
+ ss = mgp->ss;
tx = &ss->tx;
again:
req = tx->req_list;
@@ -2629,7 +2806,21 @@
static struct net_device_stats *myri10ge_get_stats(struct net_device *dev)
{
struct myri10ge_priv *mgp = netdev_priv(dev);
- return &mgp->stats;
+ struct myri10ge_slice_netstats *slice_stats;
+ struct net_device_stats *stats = &mgp->stats;
+ int i;
+
+ memset(stats, 0, sizeof(*stats));
+ for (i = 0; i < mgp->num_slices; i++) {
+ slice_stats = &mgp->ss[i].stats;
+ stats->rx_packets += slice_stats->rx_packets;
+ stats->tx_packets += slice_stats->tx_packets;
+ stats->rx_bytes += slice_stats->rx_bytes;
+ stats->tx_bytes += slice_stats->tx_bytes;
+ stats->rx_dropped += slice_stats->rx_dropped;
+ stats->tx_dropped += slice_stats->tx_dropped;
+ }
+ return stats;
}
static void myri10ge_set_multicast_list(struct net_device *dev)
@@ -2840,10 +3031,10 @@
*
* If the driver can neither enable ECRC nor verify that it has
* already been enabled, then it must use a firmware image which works
- * around unaligned completion packets (myri10ge_ethp_z8e.dat), and it
+ * around unaligned completion packets (myri10ge_rss_ethp_z8e.dat), and it
* should also ensure that it never gives the device a Read-DMA which is
* larger than 2KB by setting the tx_boundary to 2KB. If ECRC is
- * enabled, then the driver should use the aligned (myri10ge_eth_z8e.dat)
+ * enabled, then the driver should use the aligned (myri10ge_rss_eth_z8e.dat)
* firmware image, and set tx_boundary to 4KB.
*/
@@ -2872,7 +3063,7 @@
* completions) in order to see if it works on this host.
*/
mgp->fw_name = myri10ge_fw_aligned;
- status = myri10ge_load_firmware(mgp);
+ status = myri10ge_load_firmware(mgp, 1);
if (status != 0) {
goto abort;
}
@@ -3053,6 +3244,7 @@
struct myri10ge_tx_buf *tx;
u32 reboot;
int status;
+ int i;
u16 cmd, vendor;
mgp->watchdog_resets++;
@@ -3100,20 +3292,26 @@
printk(KERN_ERR "myri10ge: %s: device timeout, resetting\n",
mgp->dev->name);
- tx = &mgp->ss.tx;
- printk(KERN_INFO "myri10ge: %s: %d %d %d %d %d\n",
- mgp->dev->name, tx->req, tx->done,
- tx->pkt_start, tx->pkt_done,
- (int)ntohl(mgp->ss.fw_stats->send_done_count));
- msleep(2000);
- printk(KERN_INFO "myri10ge: %s: %d %d %d %d %d\n",
- mgp->dev->name, tx->req, tx->done,
- tx->pkt_start, tx->pkt_done,
- (int)ntohl(mgp->ss.fw_stats->send_done_count));
+ for (i = 0; i < mgp->num_slices; i++) {
+ tx = &mgp->ss[i].tx;
+ printk(KERN_INFO
+ "myri10ge: %s: (%d): %d %d %d %d %d\n",
+ mgp->dev->name, i, tx->req, tx->done,
+ tx->pkt_start, tx->pkt_done,
+ (int)ntohl(mgp->ss[i].fw_stats->
+ send_done_count));
+ msleep(2000);
+ printk(KERN_INFO
+ "myri10ge: %s: (%d): %d %d %d %d %d\n",
+ mgp->dev->name, i, tx->req, tx->done,
+ tx->pkt_start, tx->pkt_done,
+ (int)ntohl(mgp->ss[i].fw_stats->
+ send_done_count));
+ }
}
rtnl_lock();
myri10ge_close(mgp->dev);
- status = myri10ge_load_firmware(mgp);
+ status = myri10ge_load_firmware(mgp, 1);
if (status != 0)
printk(KERN_ERR "myri10ge: %s: failed to load firmware\n",
mgp->dev->name);
@@ -3133,50 +3331,59 @@
{
struct myri10ge_priv *mgp;
struct myri10ge_slice_state *ss;
+ int i, reset_needed;
u32 rx_pause_cnt;
mgp = (struct myri10ge_priv *)arg;
- rx_pause_cnt = ntohl(mgp->ss.fw_stats->dropped_pause);
+ rx_pause_cnt = ntohl(mgp->ss[0].fw_stats->dropped_pause);
+ for (i = 0, reset_needed = 0;
+ i < mgp->num_slices && reset_needed == 0; ++i) {
- ss = &mgp->ss;
- if (ss->rx_small.watchdog_needed) {
- myri10ge_alloc_rx_pages(mgp, &ss->rx_small,
- mgp->small_bytes + MXGEFW_PAD, 1);
- if (ss->rx_small.fill_cnt - ss->rx_small.cnt >=
- myri10ge_fill_thresh)
- ss->rx_small.watchdog_needed = 0;
- }
- if (ss->rx_big.watchdog_needed) {
- myri10ge_alloc_rx_pages(mgp, &ss->rx_big, mgp->big_bytes, 1);
- if (ss->rx_big.fill_cnt - ss->rx_big.cnt >=
- myri10ge_fill_thresh)
- ss->rx_big.watchdog_needed = 0;
- }
-
- if (ss->tx.req != ss->tx.done &&
- ss->tx.done == ss->watchdog_tx_done &&
- ss->watchdog_tx_req != ss->watchdog_tx_done) {
- /* nic seems like it might be stuck.. */
- if (rx_pause_cnt != mgp->watchdog_pause) {
- if (net_ratelimit())
- printk(KERN_WARNING "myri10ge %s:"
- "TX paused, check link partner\n",
- mgp->dev->name);
- } else {
- schedule_work(&mgp->watchdog_work);
- return;
+ ss = &mgp->ss[i];
+ if (ss->rx_small.watchdog_needed) {
+ myri10ge_alloc_rx_pages(mgp, &ss->rx_small,
+ mgp->small_bytes + MXGEFW_PAD,
+ 1);
+ if (ss->rx_small.fill_cnt - ss->rx_small.cnt >=
+ myri10ge_fill_thresh)
+ ss->rx_small.watchdog_needed = 0;
+ }
+ if (ss->rx_big.watchdog_needed) {
+ myri10ge_alloc_rx_pages(mgp, &ss->rx_big,
+ mgp->big_bytes, 1);
+ if (ss->rx_big.fill_cnt - ss->rx_big.cnt >=
+ myri10ge_fill_thresh)
+ ss->rx_big.watchdog_needed = 0;
+ }
+
+ if (ss->tx.req != ss->tx.done &&
+ ss->tx.done == ss->watchdog_tx_done &&
+ ss->watchdog_tx_req != ss->watchdog_tx_done) {
+ /* nic seems like it might be stuck.. */
+ if (rx_pause_cnt != mgp->watchdog_pause) {
+ if (net_ratelimit())
+ printk(KERN_WARNING "myri10ge %s:"
+ "TX paused, check link partner\n",
+ mgp->dev->name);
+ } else {
+ reset_needed = 1;
+ }
}
+ ss->watchdog_tx_done = ss->tx.done;
+ ss->watchdog_tx_req = ss->tx.req;
}
- /* rearm timer */
- mod_timer(&mgp->watchdog_timer,
- jiffies + myri10ge_watchdog_timeout * HZ);
- ss->watchdog_tx_done = ss->tx.done;
- ss->watchdog_tx_req = ss->tx.req;
mgp->watchdog_pause = rx_pause_cnt;
+
+ if (reset_needed) {
+ schedule_work(&mgp->watchdog_work);
+ } else {
+ /* rearm timer */
+ mod_timer(&mgp->watchdog_timer,
+ jiffies + myri10ge_watchdog_timeout * HZ);
+ }
}
-#if 0
static void myri10ge_free_slices(struct myri10ge_priv *mgp)
{
struct myri10ge_slice_state *ss;
@@ -3360,14 +3567,12 @@
mgp->fw_name = old_fw;
myri10ge_load_firmware(mgp, 0);
}
-#endif
static int myri10ge_probe(struct pci_dev *pdev, const struct pci_device_id *ent)
{
struct net_device *netdev;
struct myri10ge_priv *mgp;
struct device *dev = &pdev->dev;
- size_t bytes;
int i;
int status = -ENXIO;
int dac_enabled;
@@ -3382,7 +3587,6 @@
mgp = netdev_priv(netdev);
mgp->dev = netdev;
- netif_napi_add(netdev, &mgp->ss.napi, myri10ge_poll, myri10ge_napi_weight);
mgp->pdev = pdev;
mgp->csum_flag = MXGEFW_FLAGS_CKSUM;
mgp->pause = myri10ge_flow_control;
@@ -3428,11 +3632,6 @@
if (mgp->cmd == NULL)
goto abort_with_netdev;
- mgp->ss.fw_stats = dma_alloc_coherent(&pdev->dev, sizeof(*mgp->ss.fw_stats),
- &mgp->ss.fw_stats_bus, GFP_KERNEL);
- if (mgp->ss.fw_stats == NULL)
- goto abort_with_cmd;
-
mgp->board_span = pci_resource_len(pdev, 0);
mgp->iomem_base = pci_resource_start(pdev, 0);
mgp->mtrr = -1;
@@ -3469,26 +3668,24 @@
for (i = 0; i < ETH_ALEN; i++)
netdev->dev_addr[i] = mgp->mac_addr[i];
- /* allocate rx done ring */
- bytes = mgp->max_intr_slots * sizeof(*mgp->ss.rx_done.entry);
- mgp->ss.rx_done.entry = dma_alloc_coherent(&pdev->dev, bytes,
- &mgp->ss.rx_done.bus, GFP_KERNEL);
- if (mgp->ss.rx_done.entry == NULL)
- goto abort_with_ioremap;
- memset(mgp->ss.rx_done.entry, 0, bytes);
-
myri10ge_select_firmware(mgp);
- status = myri10ge_load_firmware(mgp);
+ status = myri10ge_load_firmware(mgp, 1);
if (status != 0) {
dev_err(&pdev->dev, "failed to load firmware\n");
- goto abort_with_rx_done;
+ goto abort_with_ioremap;
+ }
+ myri10ge_probe_slices(mgp);
+ status = myri10ge_alloc_slices(mgp);
+ if (status != 0) {
+ dev_err(&pdev->dev, "failed to alloc slice state\n");
+ goto abort_with_firmware;
}
status = myri10ge_reset(mgp);
if (status != 0) {
dev_err(&pdev->dev, "failed reset\n");
- goto abort_with_firmware;
+ goto abort_with_slices;
}
pci_set_drvdata(pdev, mgp);
@@ -3533,24 +3730,27 @@
dev_err(&pdev->dev, "register_netdev failed: %d\n", status);
goto abort_with_state;
}
- dev_info(dev, "%s IRQ %d, tx bndry %d, fw %s, WC %s\n",
- (mgp->msi_enabled ? "MSI" : "xPIC"),
- netdev->irq, mgp->tx_boundary, mgp->fw_name,
- (mgp->wc_enabled ? "Enabled" : "Disabled"));
+ if (mgp->msix_enabled)
+ dev_info(dev, "%d MSI-X IRQs, tx bndry %d, fw %s, WC %s\n",
+ mgp->num_slices, mgp->tx_boundary, mgp->fw_name,
+ (mgp->wc_enabled ? "Enabled" : "Disabled"));
+ else
+ dev_info(dev, "%s IRQ %d, tx bndry %d, fw %s, WC %s\n",
+ mgp->msi_enabled ? "MSI" : "xPIC",
+ netdev->irq, mgp->tx_boundary, mgp->fw_name,
+ (mgp->wc_enabled ? "Enabled" : "Disabled"));
return 0;
abort_with_state:
pci_restore_state(pdev);
+abort_with_slices:
+ myri10ge_free_slices(mgp);
+
abort_with_firmware:
myri10ge_dummy_rdma(mgp, 0);
-abort_with_rx_done:
- bytes = mgp->max_intr_slots * sizeof(*mgp->ss.rx_done.entry);
- dma_free_coherent(&pdev->dev, bytes,
- mgp->ss.rx_done.entry, mgp->ss.rx_done.bus);
-
abort_with_ioremap:
iounmap(mgp->sram);
@@ -3559,10 +3759,6 @@
if (mgp->mtrr >= 0)
mtrr_del(mgp->mtrr, mgp->iomem_base, mgp->board_span);
#endif
- dma_free_coherent(&pdev->dev, sizeof(*mgp->ss.fw_stats),
- mgp->ss.fw_stats, mgp->ss.fw_stats_bus);
-
-abort_with_cmd:
dma_free_coherent(&pdev->dev, sizeof(*mgp->cmd),
mgp->cmd, mgp->cmd_bus);
@@ -3583,7 +3779,6 @@
{
struct myri10ge_priv *mgp;
struct net_device *netdev;
- size_t bytes;
mgp = pci_get_drvdata(pdev);
if (mgp == NULL)
@@ -3598,19 +3793,15 @@
/* avoid a memory leak */
pci_restore_state(pdev);
- bytes = mgp->max_intr_slots * sizeof(*mgp->ss.rx_done.entry);
- dma_free_coherent(&pdev->dev, bytes,
- mgp->ss.rx_done.entry, mgp->ss.rx_done.bus);
-
iounmap(mgp->sram);
#ifdef CONFIG_MTRR
if (mgp->mtrr >= 0)
mtrr_del(mgp->mtrr, mgp->iomem_base, mgp->board_span);
#endif
- dma_free_coherent(&pdev->dev, sizeof(*mgp->ss.fw_stats),
- mgp->ss.fw_stats, mgp->ss.fw_stats_bus);
-
+ myri10ge_free_slices(mgp);
+ if (mgp->msix_vectors != NULL)
+ kfree(mgp->msix_vectors);
dma_free_coherent(&pdev->dev, sizeof(*mgp->cmd),
mgp->cmd, mgp->cmd_bus);
@@ -3643,6 +3834,15 @@
{
printk(KERN_INFO "%s: Version %s\n", myri10ge_driver.name,
MYRI10GE_VERSION_STR);
+
+ if (myri10ge_rss_hash > MXGEFW_RSS_HASH_TYPE_SRC_PORT ||
+ myri10ge_rss_hash < MXGEFW_RSS_HASH_TYPE_IPV4) {
+ printk(KERN_ERR
+ "%s: Illegal rssh hash type %d, defaulting to source port\n",
+ myri10ge_driver.name, myri10ge_rss_hash);
+ myri10ge_rss_hash = MXGEFW_RSS_HASH_TYPE_SRC_PORT;
+ }
+
return pci_register_driver(&myri10ge_driver);
}
next prev parent reply other threads:[~2008-05-09 0:21 UTC|newest]
Thread overview: 21+ messages / expand[flat|nested] mbox.gz Atom feed top
2008-05-09 0:15 [PATCH 0/16] myri10ge updates Brice Goglin
2008-05-09 0:16 ` [PATCH 01/16] myri10ge: update firmware headers Brice Goglin
2008-05-13 5:15 ` Jeff Garzik
2008-05-09 0:16 ` [PATCH 02/16] myri10ge: fix module parameter descriptions Brice Goglin
2008-05-09 0:17 ` [PATCH 03/16] myri10ge: increase and fix handoff timeout Brice Goglin
2008-05-09 0:17 ` [PATCH 04/16] myri10ge: properly align scratch buffers Brice Goglin
2008-05-09 0:17 ` [PATCH 05/16] myri10ge: don't warn on rx page allocation failure Brice Goglin
2008-05-09 0:18 ` [PATCH 06/16] myri10ge: report FIBER in ethtool for XFP based NIC Brice Goglin
2008-05-09 0:18 ` [PATCH 07/16] myri10ge: add barrier in myri10ge_send_cmd Brice Goglin
2008-05-09 0:19 ` [PATCH 08/16] myri10ge: trivial formatting fix Brice Goglin
2008-05-09 0:19 ` [PATCH 09/16] myri10ge: fix potential infinite loop in enable_ecrc Brice Goglin
2008-05-09 0:20 ` [PATCH 10/16] myri10ge: move data structures into a single slice Brice Goglin
2008-05-09 0:20 ` [PATCH 11/16] myri10ge: cleanup retrieving of firmware capabilities Brice Goglin
2008-05-09 0:20 ` [PATCH 12/16] myri10ge: fix the number of interrupt slots Brice Goglin
2008-05-09 0:21 ` [PATCH 13/16] myri10ge: add routines for multislices Brice Goglin
2008-05-13 5:47 ` Jeff Garzik
2008-05-13 18:34 ` Brice Goglin
2008-05-13 18:36 ` [PATCH][MAINTAINERS] Add maintainers for myri10ge driver Brice Goglin
2008-05-09 0:21 ` Brice Goglin [this message]
2008-05-09 0:22 ` [PATCH 15/16] myri10ge: add Direct Cache Access support Brice Goglin
2008-05-09 0:22 ` [PATCH 16/16] myri10ge: update driver version Brice Goglin
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=4823991D.2090906@myri.com \
--to=brice@myri.com \
--cc=jeff@garzik.org \
--cc=netdev@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.