From: "Jerry Quinn (ibm)" <jlquinn@optonline.net>
To: "John W. Linville" <linville@tuxdriver.com>
Cc: linux-wireless@vger.kernel.org, mcgrof@gmail.com, mickflemm@gmail.com
Subject: Re: ath5k can't connect on 5424
Date: Thu, 29 May 2008 11:10:10 -0400 [thread overview]
Message-ID: <483EC752.1040609@optonline.net> (raw)
In-Reply-To: <20080528002814.GF7779@tuxdriver.com>
John W. Linville wrote:
> On Sat, May 24, 2008 at 07:27:35PM -0400, Jerry Quinn wrote:
>
>> Hi. I just installed compat-wireless 2008-05-24.
>>
>> The good news is that ath5k now loads into the kernel and can talk to the
>> chip. However, beyond that, the device doesn't do anything. During
>> modprobe ath5k, I get
>>
>>
>> ACPI: PCI Interrupt 0000:03:00.0[A] -> GSI 17 (level, low) -> IRQ 17
>> PCI: Setting latency timer of device 0000:03:00.0 to 64
>> ath5k_pci 0000:03:00.0: registered as 'phy1'
>> phy1: Selected rate control algorithm 'pid'
>> ath5k phy1: Atheros AR5424 chip found (MAC: 0xa3, PHY: 0x61)
>> udev: renamed network interface wlan0 to ath0
>>
>> The pci id for the chip is 168c:1014 (rev 01). This is an IBM Thinkpad
>> T60p, running Debian testing with kernel 2.6.25-2-686, the latest dist
>> kernel available.
>>
>> When I try to bring up the interface I just get a link is not ready message
>> in the kernel log with no other info. Also, iwlist ath0 scan gives me no
>> results either (I did ifconfig ath0 up beforehand).
>>
>> Let me know if there's any further diagnosis I can provide to help out.
>>
>
> You might wish to post the results of running the ath_info tool
> available from the madwifi project (sorry, I don't have the URL handy).
>
> John
>
Mike, thanks for pointing me to the updated ath_info.
Here's the dump from my chip:
naga:~/ath_info# ./ath_info -v 0xedf00000
#DBG main: sleep_ctl reg 00000000 reset_ctl reg 00000000
-==Device Information==-
MAC Version: 2424 (0xa0)
MAC Revision: 5424 (0xa3)
Warning: Invalid EEPROM Magic number!
Device type: 3
5GHz PHY Revision: SChip (0xa2)
2GHz PHY Revision: SChip (0xa2)
/============== EEPROM Information =============\
| EEPROM Version: 5.3 | EEPROM Size: 4 kbit |
| EEMAP: 2 | Reg. Domain: 0x62 |
|================= Capabilities ================|
| 802.11a Support: yes | Turbo-A disabled: yes |
| 802.11b Support: yes | Turbo-G disabled: yes |
| 802.11g Support: yes | 2GHz XR disabled: no |
| RFKill Support: yes | 5GHz XR disabled: no |
| 32kHz Crystal: no | |
\===============================================/
/=========================================================\
| Calibration data common for all modes |
|=========================================================|
| CCK/OFDM gain delta: 1 |
| CCK/OFDM power delta: 5 |
| Scaled CCK delta: 5 |
| 2GHz Antenna gain: 0 |
| 5GHz Antenna gain: 0 |
| Turbo 2W maximum dBm: 38 |
| Target power start: 0x1bd |
| EAR Start: 0x21f |
\=========================================================/
/=========================================================\
| Calibration data for 802.11a operation |
|=========================================================|
| I power: 0x08 | Q power: 0x1f |
| Use fixed bias: 0x00 | Max turbo power: 0x26 |
| Max XR power: 0x18 | Switch Settling Time: 0x2d |
| Tx/Rx attenuation: 0x2e | TX end to XLNA On: 0x02 |
| TX end to XPA Off: 0x00 | TX end to XPA On: 0x0e |
| 62db Threshold: 0x0f | XLNA gain: 0x0d |
| XPD: 0x01 | XPD gain: 0x0a |
| I gain: 0x00 | Tx/Rx margin: 0x13 |
| False detect backoff: 0x00 | Noise Floor Threshold: -54 |
| ADC desired size: -32 | PGA desired size: -80 |
|=========================================================|
| Antenna control 0: 0x00 | Antenna control 1: 0x01 |
| Antenna control 2: 0x26 | Antenna control 3: 0x26 |
| Antenna control 4: 0x06 | Antenna control 5: 0x06 |
| Antenna control 6: 0x02 | Antenna control 7: 0x25 |
| Antenna control 8: 0x25 | Antenna control 9: 0x05 |
| Antenna control 10: 0x05 | Antenna control 11: 0x00 |
|=========================================================|
| Octave Band 0: 5 | db 0: 5 |
| Octave Band 1: 5 | db 1: 5 |
| Octave Band 2: 5 | db 2: 5 |
| Octave Band 3: 5 | db 3: 5 |
\=========================================================/
/============== Per rate power calibration ===========\
| Freq | 6-24Mbit/s | 36Mbit/s | 48Mbit/s | 54Mbit/s |
|======|============|==========|===========|==========|
| 4920 | 12.00 | 12.00 | 12.00 | 8.00 |
|======|============|==========|===========|==========|
| 5080 | 12.00 | 12.00 | 12.00 | 8.00 |
|======|============|==========|===========|==========|
| 5170 | 16.00 | 16.00 | 14.00 | 13.00 |
|======|============|==========|===========|==========|
| 5240 | 16.00 | 16.00 | 14.00 | 13.00 |
|======|============|==========|===========|==========|
| 5260 | 17.00 | 16.00 | 14.00 | 13.00 |
|======|============|==========|===========|==========|
| 5700 | 17.00 | 16.00 | 14.00 | 13.00 |
|======|============|==========|===========|==========|
| 5745 | 16.00 | 15.00 | 14.00 | 11.00 |
|======|============|==========|===========|==========|
| 5825 | 16.00 | 15.00 | 14.00 | 11.00 |
|======|============|==========|===========|==========|
| 5360 | 18.00 | 18.00 | 18.00 | 18.00 |
|======|============|==========|===========|==========|
| 5720 | 18.00 | 18.00 | 18.00 | 18.00 |
\=====================================================/
/=================== Per channel power calibration ====================\
| Freq | pwr_0 | pwr_1 | pwr_2 | pwr_3 |pwrx3_0|pwrx3_1|pwrx3_2|max_pwr|
| | pcdac | pcdac | pcdac | pcdac | pcdac | pcdac | pcdac | |
|======|=======|=======|=======|=======|=======|=======|=======|=======|
| 5045 | 11.01 | 18.01 | 20.00 | 31.03 | 0.01 | 3.02 | 11.01 | 31.03 |
| | [25] | [44] | [48] | [63] | [20] | [35] | [63] | |
|======|=======|=======|=======|=======|=======|=======|=======|=======|
| 5185 | 5.00 | 18.02 | 21.02 | 25.00 | 42.02 | 46.01 | 51.01 | 25.00 |
| | [0] | [24] | [27] | [30] | [20] | [35] | [63] | |
|======|=======|=======|=======|=======|=======|=======|=======|=======|
| 5220 | 8.00 | 32.00 | 17.00 | 18.02 | 1.00 | 10.02 | 26.01 | 18.02 |
| | [153] | [178] | [198] | [208] | [20] | [35] | [63] | |
|======|=======|=======|=======|=======|=======|=======|=======|=======|
| 5435 | 21.01 | 6.03 | 32.00 | 32.00 | 34.01 | 42.02 | 1.02 | 32.00 |
| | [50] | [54] | [72] | [103] | [20] | [35] | [63] | |
|======|=======|=======|=======|=======|=======|=======|=======|=======|
| 5535 | 22.00 | 55.01 | 17.03 | 4.01 | 18.01 | 24.02 | 2.01 | 4.01 |
| | [171] | [171] | [173] | [177] | [20] | [35] | [63] | |
|======|=======|=======|=======|=======|=======|=======|=======|=======|
| 5100 | 1.01 | 12.02 | 10.00 | 54.01 | 24.00 | 36.00 | 18.02 | 54.01 |
| | [98] | [119] | [145] | [150] | [20] | [35] | [63] | |
|======|=======|=======|=======|=======|=======|=======|=======|=======|
| 4825 | 54.01 | 42.02 | 1.01 | 11.02 | 25.01 | 6.03 | 32.00 | 11.02 |
| | [144] | [167] | [175] | [197] | [20] | [35] | [63] | |
|======|=======|=======|=======|=======|=======|=======|=======|=======|
| 4890 | 18.02 | 28.02 | 34.01 | 10.02 | 13.03 | 55.01 | 21.02 | 10.02 |
| | [22] | [28] | [44] | [54] | [20] | [35] | [63] | |
|======|=======|=======|=======|=======|=======|=======|=======|=======|
| 5045 | 24.00 | 32.00 | 18.02 | 28.02 | 1.02 | 11.02 | 5.03 | 28.02 |
| | [161] | [186] | [205] | [215] | [20] | [35] | [63] | |
|======|=======|=======|=======|=======|=======|=======|=======|=======|
| 4925 | 17.03 | 5.03 | 16.00 | 36.00 | 26.01 | 42.02 | 1.02 | 36.00 |
| | [46] | [60] | [78] | [107] | [20] | [35] | [63] | |
\======================================================================/
/=========================================================\
| Calibration data for 802.11b operation |
|=========================================================|
| I power: 0x00 | Q power: 0x00 |
| Use fixed bias: 0x00 | Max turbo power: 0x00 |
| Max XR power: 0x00 | Switch Settling Time: 0x28 |
| Tx/Rx attenuation: 0x1c | TX end to XLNA On: 0x02 |
| TX end to XPA Off: 0x00 | TX end to XPA On: 0x07 |
| 62db Threshold: 0x1c | XLNA gain: 0x0d |
| XPD: 0x01 | XPD gain: 0x0a |
| I gain: 0x00 | Tx/Rx margin: 0x14 |
| False detect backoff: 0x00 | Noise Floor Threshold: -1 |
| ADC desired size: -62 | PGA desired size: -104 |
|=========================================================|
| Antenna control 0: 0x00 | Antenna control 1: 0x0d |
| Antenna control 2: 0x2a | Antenna control 3: 0x2a |
| Antenna control 4: 0x22 | Antenna control 5: 0x22 |
| Antenna control 6: 0x0e | Antenna control 7: 0x29 |
| Antenna control 8: 0x29 | Antenna control 9: 0x21 |
| Antenna control 10: 0x21 | Antenna control 11: 0x00 |
|=========================================================|
| Octave Band 0: 5 | db 0: 5 |
| Octave Band 1: 5 | db 1: 5 |
| Octave Band 2: 0 | db 2: 0 |
| Octave Band 3: 0 | db 3: 0 |
\=========================================================/
/=================== Per channel power calibration ====================\
| Freq | pwr_0 | pwr_1 | pwr_2 | pwr_3 |pwrx3_0|pwrx3_1|pwrx3_2|max_pwr|
| | pcdac | pcdac | pcdac | pcdac | pcdac | pcdac | pcdac | |
|======|=======|=======|=======|=======|=======|=======|=======|=======|
| 2412 | 6.00 | 22.01 | 21.02 | 6.03 | 18.01 | 31.02 | 30.01 | 6.03 |
| | [170] | [170] | [174] | [178] | [20] | [35] | [63] | |
\======================================================================/
/=========================================================\
| Calibration data for 802.11g operation |
|=========================================================|
| I power: 0x00 | Q power: 0x10 |
| Use fixed bias: 0x01 | Max turbo power: 0x26 |
| Max XR power: 0x24 | Switch Settling Time: 0x28 |
| Tx/Rx attenuation: 0x1c | TX end to XLNA On: 0x02 |
| TX end to XPA Off: 0x00 | TX end to XPA On: 0x0e |
| 62db Threshold: 0x1c | XLNA gain: 0x0d |
| XPD: 0x01 | XPD gain: 0x0a |
| I gain: 0x00 | Tx/Rx margin: 0x14 |
| False detect backoff: 0x00 | Noise Floor Threshold: -1 |
| ADC desired size: -40 | PGA desired size: -105 |
|=========================================================|
| Antenna control 0: 0x00 | Antenna control 1: 0x0d |
| Antenna control 2: 0x2a | Antenna control 3: 0x2a |
| Antenna control 4: 0x22 | Antenna control 5: 0x22 |
| Antenna control 6: 0x0e | Antenna control 7: 0x29 |
| Antenna control 8: 0x29 | Antenna control 9: 0x21 |
| Antenna control 10: 0x21 | Antenna control 11: 0x05 |
|=========================================================|
| Octave Band 0: 5 | db 0: 5 |
| Octave Band 1: 5 | db 1: 5 |
| Octave Band 2: 0 | db 2: 0 |
| Octave Band 3: 0 | db 3: 0 |
\=========================================================/
/=================== Per channel power calibration ====================\
| Freq | pwr_0 | pwr_1 | pwr_2 | pwr_3 |pwrx3_0|pwrx3_1|pwrx3_2|max_pwr|
| | pcdac | pcdac | pcdac | pcdac | pcdac | pcdac | pcdac | |
|======|=======|=======|=======|=======|=======|=======|=======|=======|
| 2412 | 1.02 | 11.02 | 61.03 | 23.00 | 32.00 | 36.00 | 17.02 | 23.00 |
| | [98] | [121] | [123] | [129] | [20] | [35] | [63] | |
\======================================================================/
GPIO registers: CR 0x00018003, DO 0x00000001, DI 0x0000000b
STA_ID0: 00:16:cf:23:6f:9e
STA_ID1: 0x1b809e6f, AP: 0, IBSS: 0, KeyCache Disable: 0
TIMER0: 0x00000030, TBTT: 48, TU: 0x00070030
TIMER1: 0x0007ffff, DMAb: 65535, TU: 0x0006ffff (-49)
TIMER2: 0x01ffffff, SWBA: 65535, TU: 0x003fffff (+3735503)
TIMER3: 0x00000031, ATIM: 49, TU: 0x00070031 (+1)
TSF: 0x000000001a8bf0f6, TSFTU: 41724, TU: 0x0006a2fc
BEACON: 0x00000000
LAST_TSTP: 0x007fe01f
next prev parent reply other threads:[~2008-05-29 15:10 UTC|newest]
Thread overview: 6+ messages / expand[flat|nested] mbox.gz Atom feed top
2008-05-24 23:27 ath5k can't connect on 5424 Jerry Quinn
2008-05-28 0:28 ` John W. Linville
2008-05-29 4:57 ` Michael Renzmann
2008-05-29 15:10 ` Jerry Quinn (ibm) [this message]
2008-05-29 18:52 ` Pavel Roskin
2008-05-29 19:18 ` Bob Copeland
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=483EC752.1040609@optonline.net \
--to=jlquinn@optonline.net \
--cc=linux-wireless@vger.kernel.org \
--cc=linville@tuxdriver.com \
--cc=mcgrof@gmail.com \
--cc=mickflemm@gmail.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.