From: "Mathieu Bérard" <Mathieu.Berard@crans.org>
To: Tejun Heo <htejun@gmail.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>,
linux-kernel@vger.kernel.org, linux-ide@vger.kernel.org,
ACPI Devel Maling List <linux-acpi@vger.kernel.org>,
Andrew Morton <akpm@linux-foundation.org>,
Andi Kleen <andi@firstfloor.org>, Jeff Garzik <jeff@garzik.org>
Subject: Re: 2.6.25 to 2.6.26-rc8 regression (related to ahci and acpi _GTF)
Date: Wed, 02 Jul 2008 11:04:16 +0200 [thread overview]
Message-ID: <486B4490.7080904@crans.org> (raw)
In-Reply-To: <486AEE29.2010506@gmail.com>
[-- Attachment #1: Type: text/plain, Size: 1511 bytes --]
Tejun Heo a écrit :
> Rafael J. Wysocki wrote:
>
>> [Adding CCs.]
>>
>> On Tuesday, 1 of July 2008, Mathieu Bérard wrote:
>>
>>> Hi,
>>> I have a laptop with an ICH6M SATA Controller and a Hitachi hard drive.
>>> While it worked well using the ahci module and Linux 2.6.25,
>>> it get randomly 'stuck' for several seconds to several minutes with 2.6.26-rc8.
>>> Successive errors progressively reduce the ATA link speed.
>>>
>>> Passing the libata.noacpi parameter is an effective workaround.
>>>
>>> Please note that it's not the first time i have this kind of issue, see:
>>> http://marc.info/?l=linux-ide&m=117305595312399&w=2
>>> This was found to be a bad interaction between my _GTF taskfile, which enable the
>>> "Enable Device-Initiated Interface Power State Transitions" feature, and NCQ.
>>> The driver was later NCQ blacklisted to correct the problem.
>>>
>
> Can you please post the result of "hdparm -I /dev/sda" and full kernel
> boot log? 0xca is not a NCQ command so the it's not related to NCQ at
> all. It seems we'll need to filter out DIPM commands from _GTF.
>
>
Hi,
hdparm and dmesg output attached.
I was not expecting anything related to NCQ as my drive is blacklisted,
I was just mentioning previous issue with that hardware.
Do you know what has changed in this version that is now causing failure
with DIPM ? I could bisect to try to find out, but this will be painful
as the
device hang may only appears after several minutes of disk activity.
--
Mathieu
[-- Attachment #2: hdparm_2.6.26-rc8 --]
[-- Type: text/plain, Size: 2423 bytes --]
/dev/sda:
ATA device, with non-removable media
Model Number: HTS541010G9SA00
Serial Number: MP2ZM4X0GSWJKR
Firmware Revision: MBZOC60D
Standards:
Used: ATA/ATAPI-7 T13 1532D revision 1
Supported: 7 6 5 4
Configuration:
Logical max current
cylinders 16383 16383
heads 16 16
sectors/track 63 63
--
CHS current addressable sectors: 16514064
LBA user addressable sectors: 195371568
LBA48 user addressable sectors: 195371568
device size with M = 1024*1024: 95396 MBytes
device size with M = 1000*1000: 100030 MBytes (100 GB)
Capabilities:
LBA, IORDY(can be disabled)
Queue depth: 32
Standby timer values: spec'd by Vendor, no device specific minimum
R/W multiple sector transfer: Max = 16 Current = 0
Advanced power management level: 128
Recommended acoustic management value: 128, current value: 254
DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5
Cycle time: min=120ns recommended=120ns
PIO: pio0 pio1 pio2 pio3 pio4
Cycle time: no flow control=240ns IORDY flow control=120ns
Commands/features:
Enabled Supported:
* SMART feature set
Security Mode feature set
* Power Management feature set
* Write cache
* Look-ahead
* Host Protected Area feature set
* WRITE_BUFFER command
* READ_BUFFER command
* NOP cmd
* DOWNLOAD_MICROCODE
* Advanced Power Management feature set
Power-Up In Standby feature set
* SET_FEATURES required to spinup after power up
SET_MAX security extension
Automatic Acoustic Management feature set
* 48-bit Address feature set
* Device Configuration Overlay feature set
* Mandatory FLUSH_CACHE
* FLUSH_CACHE_EXT
* SMART error logging
* SMART self-test
* General Purpose Logging feature set
* WRITE_{DMA|MULTIPLE}_FUA_EXT
* IDLE_IMMEDIATE with UNLOAD
* SATA-I signaling speed (1.5Gb/s)
* Native Command Queueing (NCQ)
* Host-initiated interface power management
Non-Zero buffer offsets in DMA Setup FIS
DMA Setup Auto-Activate optimization
Device-initiated interface power management
In-order data delivery
* Software settings preservation
Security:
Master password revision code = 65534
supported
not enabled
not locked
not frozen
not expired: security count
not supported: enhanced erase
64min for SECURITY ERASE UNIT.
Checksum: correct
[-- Attachment #3: dmesg_2.6.26-rc8 --]
[-- Type: text/plain, Size: 49172 bytes --]
[ 0.000000] Linux version 2.6.26-rc8 (mathieu@manwe) (gcc version 4.3.1 (Ubuntu 4.3.1-3ubuntu1) ) #1 PREEMPT Mon Jun 30 01:12:00 CEST 2008
[ 0.000000] PAT disabled. Not yet verified on this CPU type.
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
[ 0.000000] BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000d2000 - 00000000000d4000 (reserved)
[ 0.000000] BIOS-e820: 00000000000dc000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000003fee0000 (usable)
[ 0.000000] BIOS-e820: 000000003fee0000 - 000000003feea000 (ACPI data)
[ 0.000000] BIOS-e820: 000000003feea000 - 000000003ff00000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000003ff00000 - 0000000040000000 (reserved)
[ 0.000000] BIOS-e820: 00000000e0000000 - 00000000f0006000 (reserved)
[ 0.000000] BIOS-e820: 00000000f0008000 - 00000000f000c000 (reserved)
[ 0.000000] BIOS-e820: 00000000fed20000 - 00000000fed90000 (reserved)
[ 0.000000] BIOS-e820: 00000000ff000000 - 0000000100000000 (reserved)
[ 0.000000] 126MB HIGHMEM available.
[ 0.000000] 896MB LOWMEM available.
[ 0.000000] NX (Execute Disable) protection: active
[ 0.000000] Entering add_active_range(0, 0, 261856) 0 entries of 256 used
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0 -> 4096
[ 0.000000] Normal 4096 -> 229376
[ 0.000000] HighMem 229376 -> 261856
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0 -> 261856
[ 0.000000] On node 0 totalpages: 261856
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 4064 pages, LIFO batch:0
[ 0.000000] Normal zone: 1760 pages used for memmap
[ 0.000000] Normal zone: 223520 pages, LIFO batch:31
[ 0.000000] HighMem zone: 254 pages used for memmap
[ 0.000000] HighMem zone: 32226 pages, LIFO batch:7
[ 0.000000] Movable zone: 0 pages used for memmap
[ 0.000000] DMI present.
[ 0.000000] ACPI: RSDP 000F6950, 0014 (r0 TOSCPL)
[ 0.000000] ACPI: RSDT 3FEE1FCA, 0044 (r1 TOSCPL RSDT 6040000 LTP 0)
[ 0.000000] ACPI: APIC 3FEE9E88, 0068 (r1 INTEL ALVISO 6040000 LOHR 5F)
[ 0.000000] ACPI: FACP 3FEE9EF0, 0074 (r1 TOSCPL ALVISO 6040000 LOHR 32)
[ 0.000000] ACPI: DSDT 3FEE2A72, 7416 (r1 TOSCPL ALVISO 6040000 MSFT 3000000)
[ 0.000000] ACPI: FACS 3FEFAFC0, 0040
[ 0.000000] ACPI: BOOT 3FEE9FD8, 0028 (r1 PTLTD $SBFTBL$ 6040000 LTP 1)
[ 0.000000] ACPI: MCFG 3FEE9F9C, 003C (r1 INTEL ALVISO 6040000 LOHR 5F)
[ 0.000000] ACPI: SSDT 3FEE2840, 022E (r1 SataRe SataAhci 1000 INTL 20030224)
[ 0.000000] ACPI: SSDT 3FEE2405, 022B (r1 PmRef Cpu0Ist 3000 INTL 20030224)
[ 0.000000] ACPI: SSDT 3FEE2227, 01DE (r1 PmRef Cpu0Cst 3001 INTL 20030224)
[ 0.000000] ACPI: SSDT 3FEE200E, 0219 (r1 PmRef CpuPm 3000 INTL 20030224)
[ 0.000000] ACPI: DMI detected: Toshiba
[ 0.000000] ACPI: PM-Timer IO Port: 0x1008
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] disabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] Allocating PCI resources starting at 50000000 (gap: 40000000:a0000000)
[ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000d2000
[ 0.000000] PM: Registered nosave memory: 00000000000d2000 - 00000000000d4000
[ 0.000000] PM: Registered nosave memory: 00000000000d4000 - 00000000000dc000
[ 0.000000] PM: Registered nosave memory: 00000000000dc000 - 0000000000100000
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 259810
[ 0.000000] Kernel command line: root=UUID=8aa84942-b9a7-4622-a512-c180ce3095db ro savedefault single
[ 0.000000] mapped APIC to ffffb000 (fee00000)
[ 0.000000] mapped IOAPIC to ffffa000 (fec00000)
[ 0.000000] Enabling fast FPU save and restore... done.
[ 0.000000] Enabling unmasked SIMD FPU exception support... done.
[ 0.000000] Initializing CPU#0
[ 0.000000] Preemptible RCU implementation.
[ 0.000000] CPU 0 irqstacks, hard=c03b8000 soft=c03b7000
[ 0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes)
[ 0.000000] Detected 1729.103 MHz processor.
[ 0.000999] Console: colour VGA+ 80x25
[ 0.000999] console [tty0] enabled
[ 0.000999] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000999] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000999] Memory: 1030072k/1047424k available (1773k kernel code, 16608k reserved, 799k data, 188k init, 129920k highmem)
[ 0.000999] virtual kernel memory layout:
[ 0.000999] fixmap : 0xfffa8000 - 0xfffff000 ( 348 kB)
[ 0.000999] pkmap : 0xffa00000 - 0xffc00000 (2048 kB)
[ 0.000999] vmalloc : 0xf8800000 - 0xff9fe000 ( 113 MB)
[ 0.000999] lowmem : 0xc0000000 - 0xf8000000 ( 896 MB)
[ 0.000999] .init : 0xc0385000 - 0xc03b4000 ( 188 kB)
[ 0.000999] .data : 0xc02bb5f8 - 0xc0383538 ( 799 kB)
[ 0.000999] .text : 0xc0100000 - 0xc02bb5f8 (1773 kB)
[ 0.000999] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[ 0.000999] CPA: page pool initialized 1 of 1 pages preallocated
[ 0.000999] SLUB: Genslabs=12, HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.061050] Calibrating delay using timer specific routine.. 3460.32 BogoMIPS (lpj=1730163)
[ 0.061163] Mount-cache hash table entries: 512
[ 0.061341] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 0.061427] CPU: L2 cache: 2048K
[ 0.061476] Intel machine check architecture supported.
[ 0.061529] Intel machine check reporting enabled on CPU#0.
[ 0.061586] CPU: Intel(R) Pentium(R) M processor 1.73GHz stepping 08
[ 0.061711] Checking 'hlt' instruction... OK.
[ 0.065337] Freeing SMP alternatives: 0k freed
[ 0.065387] ACPI: Core revision 20080321
[ 0.077988] ENABLING IO-APIC IRQs
[ 0.077988] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.087986] net_namespace: 480 bytes
[ 0.087986] NET: Registered protocol family 16
[ 0.087986] ACPI: bus type pci registered
[ 0.087986] PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255
[ 0.087986] PCI: MCFG area at e0000000 reserved in E820
[ 0.087986] PCI: Using MMCONFIG for extended config space
[ 0.087986] PCI: Using configuration type 1 for base access
[ 0.087986] Setting up standard PCI resources
[ 0.092423] ACPI: EC: Look up EC in DSDT
[ 0.095508] ACPI: Interpreter enabled
[ 0.095558] ACPI: (supports S0 S3 S4 S5)
[ 0.095759] ACPI: Using IOAPIC for interrupt routing
[ 0.140766] ACPI: EC: GPE = 0x1d, I/O: command/status = 0x66, data = 0x62
[ 0.140822] ACPI: EC: driver started in poll mode
[ 0.140891] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 0.141686] pci 0000:00:1f.0: Force enabled HPET at 0xfed00000
[ 0.141693] pci 0000:00:1f.0: quirk: region 1000-107f claimed by ICH6 ACPI/GPIO/TCO
[ 0.141757] pci 0000:00:1f.0: quirk: region 1180-11bf claimed by ICH6 GPIO
[ 0.142803] PCI: Transparent bridge - 0000:00:1e.0
[ 0.142908] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.143252] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEGP._PRT]
[ 0.143413] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP01._PRT]
[ 0.143566] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP02._PRT]
[ 0.143730] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT]
[ 0.150741] ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 *10 12 14 15)
[ 0.151338] ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 11 12 14 15) *10
[ 0.151970] ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 10 12 14 15) *11
[ 0.152604] ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 *11 12 14 15)
[ 0.153196] ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 5 6 7 10 12 14 15) *11
[ 0.153830] ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 7 *11 12 14 15)
[ 0.154422] ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 4 5 6 7 10 12 14 15) *11
[ 0.154976] ACPI: PCI Interrupt Link [LNKH] (IRQs 1 3 4 5 6 7 *11 12 14 15)
[ 0.155634] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 0.155696] pnp: PnP ACPI init
[ 0.155747] ACPI: bus type pnp registered
[ 0.178303] pnp: PnP ACPI: found 9 devices
[ 0.178353] ACPI: ACPI bus type pnp unregistered
[ 0.178449] PCI: Using ACPI for IRQ routing
[ 0.182234] hpet clockevent registered
[ 0.182241] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[ 0.182433] hpet0: 3 64-bit timers, 14318180 Hz
[ 0.189107] system 00:01: ioport range 0xfe00-0xfe7f has been reserved
[ 0.189163] system 00:01: ioport range 0xfe80-0xfeff has been reserved
[ 0.189217] system 00:01: ioport range 0xff00-0xff7f has been reserved
[ 0.189272] system 00:01: iomem range 0xe0000000-0xefffffff could not be reserved
[ 0.189334] system 00:01: iomem range 0xf0000000-0xf0003fff could not be reserved
[ 0.189395] system 00:01: iomem range 0xf0004000-0xf0004fff could not be reserved
[ 0.189457] system 00:01: iomem range 0xf0005000-0xf0005fff could not be reserved
[ 0.189519] system 00:01: iomem range 0xf0008000-0xf000bfff could not be reserved
[ 0.189581] system 00:01: iomem range 0xfed20000-0xfed8ffff could not be reserved
[ 0.189651] system 00:05: ioport range 0x800-0x80f has been reserved
[ 0.189705] system 00:05: ioport range 0x1000-0x107f has been reserved
[ 0.189758] system 00:05: ioport range 0x1180-0x11bf has been reserved
[ 0.189812] system 00:05: ioport range 0x1640-0x164f has been reserved
[ 0.219963] PCI: region 0000:06:04.0/9 too large: 0x0000000000000000-0x0000000003ffffff
[ 0.220032] PCI: Bridge: 0000:00:01.0
[ 0.220080] IO window: 3000-3fff
[ 0.220129] MEM window: 0xb8100000-0xb81fffff
[ 0.220181] PREFETCH window: 0x00000000c8000000-0x00000000cfffffff
[ 0.220236] PCI: Bridge: 0000:00:1c.0
[ 0.220285] IO window: 4000-4fff
[ 0.220336] MEM window: 0xbc000000-0xbfffffff
[ 0.220389] PREFETCH window: 0x00000000d0000000-0x00000000d3ffffff
[ 0.220447] PCI: Bridge: 0000:00:1c.1
[ 0.220496] IO window: 5000-5fff
[ 0.220547] MEM window: 0xc0000000-0xc3ffffff
[ 0.220600] PREFETCH window: 0x00000000d4000000-0x00000000d7ffffff
[ 0.220661] PCI: Bus 7, cardbus bridge: 0000:06:04.0
[ 0.220711] IO window: 0x00006400-0x000064ff
[ 0.220763] IO window: 0x00006800-0x000068ff
[ 0.220816] MEM window: 0x50000000-0x53ffffff
[ 0.220869] PCI: Bridge: 0000:00:1e.0
[ 0.220918] IO window: 6000-6fff
[ 0.220970] MEM window: 0xc4000000-0xc40fffff
[ 0.221023] PREFETCH window: disabled.
[ 0.221086] ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 0.221185] PCI: Setting latency timer of device 0000:00:01.0 to 64
[ 0.221205] ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 17 (level, low) -> IRQ 17
[ 0.221305] PCI: Setting latency timer of device 0000:00:1c.0 to 64
[ 0.221326] ACPI: PCI Interrupt 0000:00:1c.1[B] -> GSI 16 (level, low) -> IRQ 16
[ 0.221425] PCI: Setting latency timer of device 0000:00:1c.1 to 64
[ 0.221438] PCI: Setting latency timer of device 0000:00:1e.0 to 64
[ 0.221454] ACPI: PCI Interrupt 0000:06:04.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 0.221559] NET: Registered protocol family 2
[ 0.239044] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.239958] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.240787] TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.241114] TCP: Hash tables configured (established 131072 bind 65536)
[ 0.241169] TCP reno registered
[ 0.247066] NET: Registered protocol family 1
[ 0.247241] Unpacking initramfs... done
[ 0.479151] Freeing initrd memory: 4484k freed
[ 0.479252] Simple Boot Flag at 0x36 set to 0x1
[ 0.479684] highmem bounce pool size: 64 pages
[ 0.479743] Total HugeTLB memory allocated, 0
[ 0.480987] msgmni has been set to 1767
[ 0.481151] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
[ 0.481214] io scheduler noop registered
[ 0.481270] io scheduler cfq registered (default)
[ 0.481425] pci 0000:01:00.0: Boot video device
[ 0.481507] PCI: Setting latency timer of device 0000:00:01.0 to 64
[ 0.481535] assign_interrupt_mode Found MSI capability
[ 0.481610] Allocate Port Service[0000:00:01.0:pcie00]
[ 0.481628] Allocate Port Service[0000:00:01.0:pcie03]
[ 0.481675] PCI: Setting latency timer of device 0000:00:1c.0 to 64
[ 0.481716] assign_interrupt_mode Found MSI capability
[ 0.481806] Allocate Port Service[0000:00:1c.0:pcie00]
[ 0.481820] Allocate Port Service[0000:00:1c.0:pcie02]
[ 0.481833] Allocate Port Service[0000:00:1c.0:pcie03]
[ 0.481915] PCI: Setting latency timer of device 0000:00:1c.1 to 64
[ 0.481956] assign_interrupt_mode Found MSI capability
[ 0.482045] Allocate Port Service[0000:00:1c.1:pcie00]
[ 0.482060] Allocate Port Service[0000:00:1c.1:pcie02]
[ 0.482073] Allocate Port Service[0000:00:1c.1:pcie03]
[ 0.483062] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[ 0.483403] i8042.c: Detected active multiplexing controller, rev 1.1.
[ 0.483522] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 0.483575] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[ 0.483627] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[ 0.483678] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[ 0.483730] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[ 0.483796] mice: PS/2 mouse device common for all mice
[ 0.483867] cpuidle: using governor ladder
[ 0.483919] cpuidle: using governor menu
[ 0.484282] TCP cubic registered
[ 0.484331] Using IPI Shortcut mode
[ 0.484418] registered taskstats version 1
[ 0.484726] Freeing unused kernel memory: 188k freed
[ 0.487357] input: AT Translated Set 2 keyboard as /class/input/input0
[ 0.552083] No dock devices found.
[ 0.558425] SCSI subsystem initialized
[ 0.566002] libata version 3.00 loaded.
[ 0.567684] ahci 0000:00:1f.2: version 3.0
[ 0.567713] ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 19
[ 0.682859] Switched to high resolution mode on CPU 0
[ 1.568027] ahci 0000:00:1f.2: AHCI 0001.0000 32 slots 4 ports 1.5 Gbps 0x5 impl IDE mode
[ 1.568091] ahci 0000:00:1f.2: flags: 64bit ncq pm led slum part
[ 1.568146] PCI: Setting latency timer of device 0000:00:1f.2 to 64
[ 1.568283] scsi0 : ahci
[ 1.568398] scsi1 : ahci
[ 1.568482] scsi2 : ahci
[ 1.568568] scsi3 : ahci
[ 1.568695] ata1: SATA max UDMA/133 abar m1024@0xb8000c00 port 0xb8000d00 irq 19
[ 1.568756] ata2: DUMMY
[ 1.568803] ata3: SATA max UDMA/133 abar m1024@0xb8000c00 port 0xb8000e00 irq 19
[ 1.568864] ata4: DUMMY
[ 1.873016] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 1.874045] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded
[ 1.875000] ata1.00: ATA-7: HTS541010G9SA00, MBZOC60D, max UDMA/100
[ 1.875000] ata1.00: 195371568 sectors, multi 0: LBA48 NCQ (not used)
[ 1.875000] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded
[ 1.875000] ata1.00: configured for UDMA/100
[ 2.205015] ata3: SATA link down (SStatus 0 SControl 300)
[ 2.227086] scsi 0:0:0:0: Direct-Access ATA HTS541010G9SA00 MBZO PQ: 0 ANSI: 5
[ 2.233881] fuse init (API version 7.9)
[ 2.252219] device-mapper: uevent: version 1.0.3
[ 2.252347] device-mapper: ioctl: 4.13.0-ioctl (2007-10-18) initialised: dm-devel@redhat.com
[ 2.520087] usbcore: registered new interface driver usbfs
[ 2.520163] usbcore: registered new interface driver hub
[ 2.520470] usbcore: registered new device driver usb
[ 2.521427] USB Universal Host Controller Interface driver v3.0
[ 2.521525] ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 23
[ 2.521630] PCI: Setting latency timer of device 0000:00:1d.0 to 64
[ 2.521634] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 2.521771] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
[ 2.521863] uhci_hcd 0000:00:1d.0: irq 23, io base 0x00001800
[ 2.521984] usb usb1: configuration #1 chosen from 1 choice
[ 2.522064] hub 1-0:1.0: USB hub found
[ 2.522116] hub 1-0:1.0: 2 ports detected
[ 2.562082] 8139too Fast Ethernet driver 0.9.28
[ 2.623248] ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 23
[ 2.623368] PCI: Setting latency timer of device 0000:00:1d.7 to 64
[ 2.623372] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 2.623444] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2
[ 2.627410] ehci_hcd 0000:00:1d.7: debug port 1
[ 2.627465] PCI: cache line size of 32 is not supported by device 0000:00:1d.7
[ 2.627472] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xb8000000
[ 2.637010] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 2.637157] usb usb2: configuration #1 chosen from 1 choice
[ 2.637237] hub 2-0:1.0: USB hub found
[ 2.637291] hub 2-0:1.0: 8 ports detected
[ 2.738128] ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 19
[ 2.738240] PCI: Setting latency timer of device 0000:00:1d.1 to 64
[ 2.738244] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 2.738317] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
[ 2.738406] uhci_hcd 0000:00:1d.1: irq 19, io base 0x00001820
[ 2.738536] usb usb3: configuration #1 chosen from 1 choice
[ 2.738614] hub 3-0:1.0: USB hub found
[ 2.738667] hub 3-0:1.0: 2 ports detected
[ 2.815997] ata_piix 0000:00:1f.1: version 2.12
[ 2.815997] ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 18
[ 2.815997] PCI: Setting latency timer of device 0000:00:1f.1 to 64
[ 2.815997] scsi4 : ata_piix
[ 2.815997] scsi5 : ata_piix
[ 2.840100] ata5: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x18c0 irq 14
[ 2.840157] ata6: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x18c8 irq 15
[ 2.994584] ata5.00: ATAPI: MATSHITADVD-RAM UJ-841S, 1.50, max UDMA/33
[ 3.000504] ata5.00: configured for UDMA/33
[ 3.000582] ata6: port disabled. ignoring.
[ 3.002000] scsi 4:0:0:0: CD-ROM MATSHITA DVD-RAM UJ-841S 1.50 PQ: 0 ANSI: 5
[ 3.002001] ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18
[ 3.002001] PCI: Setting latency timer of device 0000:00:1d.2 to 64
[ 3.002001] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 3.002001] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
[ 3.002001] uhci_hcd 0000:00:1d.2: irq 18, io base 0x00001840
[ 3.003055] usb usb4: configuration #1 chosen from 1 choice
[ 3.003132] hub 4-0:1.0: USB hub found
[ 3.003184] hub 4-0:1.0: 2 ports detected
[ 3.103998] ACPI: PCI Interrupt 0000:06:04.2[C] -> GSI 18 (level, low) -> IRQ 18
[ 3.103998] ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 16 (level, low) -> IRQ 16
[ 3.103998] PCI: Setting latency timer of device 0000:00:1d.3 to 64
[ 3.103998] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[ 3.103998] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
[ 3.103998] uhci_hcd 0000:00:1d.3: irq 16, io base 0x00001860
[ 3.103998] usb usb5: configuration #1 chosen from 1 choice
[ 3.105031] hub 5-0:1.0: USB hub found
[ 3.105084] hub 5-0:1.0: 2 ports detected
[ 3.160006] usb 1-1: new low speed USB device using uhci_hcd and address 2
[ 3.161007] firewire_ohci: Added fw-ohci device 0000:06:04.2, OHCI version 1.10
[ 3.161120] ACPI: PCI Interrupt 0000:06:01.0[A] -> GSI 21 (level, low) -> IRQ 21
[ 3.161820] eth0: RealTek RTL8139 at 0xf88da000, 00:0f:b0:a5:9a:81, IRQ 21
[ 3.161874] eth0: Identified 8139 chip type 'RTL-8100B/8139D'
[ 3.211688] Driver 'sd' needs updating - please use bus_type methods
[ 3.211834] sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors (100030 MB)
[ 3.211901] sd 0:0:0:0: [sda] Write Protect is off
[ 3.211952] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 3.211973] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 3.212086] sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors (100030 MB)
[ 3.212154] sd 0:0:0:0: [sda] Write Protect is off
[ 3.212206] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 3.212228] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 3.212295] sda:<4>Driver 'sr' needs updating - please use bus_type methods
[ 3.300999] usb 1-1: configuration #1 chosen from 1 choice
[ 3.343274] usbcore: registered new interface driver hiddev
[ 3.358385] input: Logitech USB Receiver as /class/input/input1
[ 3.363033] input,hidraw0: USB HID v1.11 Mouse [Logitech USB Receiver] on usb-0000:00:1d.0-1
[ 3.393030] input: Logitech USB Receiver as /class/input/input2
[ 3.398051] input,hiddev0,hidraw1: USB HID v1.11 Device [Logitech USB Receiver] on usb-0000:00:1d.0-1
[ 3.398339] usbcore: registered new interface driver usbhid
[ 3.398392] usbhid: v2.6:USB HID core driver
[ 3.591462] sda1 sda2 < sda5 sda6 > sda3
[ 3.608998] sd 0:0:0:0: [sda] Attached SCSI disk
[ 3.629031] sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
[ 3.629031] Uniform CD-ROM driver Revision: 3.20
[ 3.629031] sr 4:0:0:0: Attached scsi CD-ROM sr0
[ 3.632962] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 3.633040] sr 4:0:0:0: Attached scsi generic sg1 type 5
[ 3.661086] firewire_core: created device fw0: GUID 00023f5b8140757f, S400
[ 4.122469] PM: Starting manual resume from disk
[ 4.130170] SGI XFS with ACLs, security attributes, realtime, no debug enabled
[ 4.132481] Filesystem "dm-0": Disabling barriers, not supported by the underlying device
[ 4.132729] XFS mounting filesystem dm-0
[ 4.214681] Ending clean XFS mount for filesystem: dm-0
[ 8.611728] Linux agpgart interface v0.103
[ 8.626735] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.03 (30-Apr-2008)
[ 8.626874] iTCO_wdt: Found a ICH6-M TCO device (Version=2, TCOBASE=0x1060)
[ 8.626957] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 8.709000] ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3] C4[C3])
[ 8.709262] ACPI: ACPI0007:00 is registered as cooling_device0
[ 8.709317] ACPI: Processor [CPU0] (supports 8 throttling states)
[ 8.725918] input: Power Button (FF) as /class/input/input3
[ 8.752060] ACPI: Power Button (FF) [PWRF]
[ 8.752177] input: Lid Switch as /class/input/input4
[ 8.764121] ACPI: Lid Switch [LID0]
[ 8.764225] input: Power Button (CM) as /class/input/input5
[ 8.788047] ACPI: Power Button (CM) [PWRB]
[ 9.173654] ieee80211_crypt: registered algorithm 'NULL'
[ 9.270000] Marking TSC unstable due to: TSC halts in idle.
[ 9.414207] ACPI: AC Adapter [ACAD] (on-line)
[ 9.667778] ACPI: Battery Slot [BAT1] (battery present)
[ 9.689219] sdhci: Secure Digital Host Controller Interface driver
[ 9.689279] sdhci: Copyright(c) Pierre Ossman
[ 9.689359] sdhci: SDHCI controller found at 0000:06:04.4 [104c:8034] (rev 0)
[ 9.689432] ACPI: PCI Interrupt 0000:06:04.4[D] -> GSI 19 (level, low) -> IRQ 19
[ 9.689551] mmc0: Will use DMA mode even though HW doesn't fully claim to support it.
[ 9.689712] mmc0: SDHCI at 0xc4009400 irq 19 DMA
[ 9.689772] mmc1: Will use DMA mode even though HW doesn't fully claim to support it.
[ 9.689862] mmc1: SDHCI at 0xc4009000 irq 19 DMA
[ 9.689921] mmc2: Will use DMA mode even though HW doesn't fully claim to support it.
[ 9.690021] mmc2: SDHCI at 0xc4006400 irq 19 DMA
[ 9.744484] input: PC Speaker as /class/input/input6
[ 9.751333] Real Time Clock Driver v1.12ac
[ 9.769279] ACPI: PCI Interrupt 0000:06:04.3[B] -> GSI 17 (level, low) -> IRQ 17
[ 9.782047] input: Video Bus as /class/input/input7
[ 9.800258] Yenta: CardBus bridge found at 0000:06:04.0 [1179:ff00]
[ 9.800339] PCI: Bus 7, cardbus bridge: 0000:06:04.0
[ 9.800390] IO window: 0x00006400-0x000064ff
[ 9.800443] IO window: 0x00006800-0x000068ff
[ 9.800496] PREFETCH window: 0x54000000-0x543fffff
[ 9.800550] MEM window: 0x50000000-0x53ffffff
[ 9.800605] Yenta: Enabling burst memory read transactions
[ 9.800660] Yenta: Using CSCINT to route CSC interrupts to PCI
[ 9.800712] Yenta: Routing CardBus interrupts to PCI
[ 9.800766] Yenta TI: socket 0000:06:04.0, mfunc 0x10aa1b22, devctl 0x66
[ 9.805070] ACPI: Video Device [VGA] (multi-head: yes rom: no post: no)
[ 9.805445] input: Video Bus as /class/input/input8
[ 9.816499] ieee80211: 802.11 data/management/control stack, git-1.1.13
[ 9.816558] ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com>
[ 9.829066] ACPI: Video Device [GFX0] (multi-head: yes rom: yes post: no)
[ 9.840479] ipw2200: Intel(R) PRO/Wireless 2200/2915 Network Driver, 1.2.2kmprq
[ 9.840547] ipw2200: Copyright(c) 2003-2006 Intel Corporation
[ 10.023833] Yenta: ISA IRQ mask 0x0cf8, PCI irq 16
[ 10.023892] Socket status: 30000006
[ 10.023942] Yenta: Raising subordinate bus# of parent bus (#06) from #07 to #0a
[ 10.024005] pcmcia: parent PCI bridge I/O window: 0x6000 - 0x6fff
[ 10.024072] pcmcia: parent PCI bridge Memory window: 0xc4000000 - 0xc40fffff
[ 10.031338] input: PS/2 Mouse as /class/input/input9
[ 10.034886] ACPI: PCI Interrupt 0000:06:02.0[A] -> GSI 22 (level, low) -> IRQ 22
[ 10.044815] ipw2200: Detected Intel PRO/Wireless 2200BG Network Connection
[ 10.044913] firmware: requesting ipw2200-bss.fw
[ 10.067714] input: AlpsPS/2 ALPS GlidePoint as /class/input/input10
[ 10.534594] ipw2200: Radio Frequency Kill Switch is On:
[ 10.534597] Kill switch must be turned off for wireless networking to work.
[ 10.535092] ipw2200: Detected geography ZZM (11 802.11bg channels, 0 802.11a channels)
[ 10.535210] ACPI: PCI Interrupt 0000:00:1e.2[A] -> GSI 17 (level, low) -> IRQ 17
[ 10.535334] PCI: Setting latency timer of device 0000:00:1e.2 to 64
[ 11.182157] Clocksource tsc unstable (delta = -77135590 ns)
[ 11.350030] intel8x0_measure_ac97_clock: measured 50736 usecs
[ 11.350082] intel8x0: clocking to 48000
[ 12.172322] Non-volatile memory driver v1.2
[ 12.185343] BIOS EDD facility v0.16 2004-Jun-25, 6 devices found
[ 12.190783] firmware: requesting intel-ucode/06-0d-08
[ 12.217045] IA-32 Microcode Update Driver: v1.14a <tigran@aivazian.fsnet.co.uk>
[ 12.229021] Machine check exception polling timer started.
[ 12.286418] Adding 1461844k swap on /dev/sda5. Priority:-1 extents:1 across:1461844k
[ 12.523578] Filesystem "dm-0": Disabling barriers, not supported by the underlying device
[ 12.939611] kjournald starting. Commit interval 5 seconds
[ 12.945052] EXT3 FS on sda1, internal journal
[ 12.945052] EXT3-fs: mounted filesystem with ordered data mode.
[ 12.977320] Filesystem "dm-3": Disabling barriers, not supported by the underlying device
[ 12.997772] XFS mounting filesystem dm-3
[ 13.098262] Ending clean XFS mount for filesystem: dm-3
[ 13.143503] Filesystem "dm-1": Disabling barriers, not supported by the underlying device
[ 13.163812] XFS mounting filesystem dm-1
[ 13.237413] Ending clean XFS mount for filesystem: dm-1
[ 13.238065] Filesystem "dm-2": Disabling barriers, not supported by the underlying device
[ 13.238211] XFS mounting filesystem dm-2
[ 13.452498] Ending clean XFS mount for filesystem: dm-2
[ 17.686089] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 23.810166] usb 2-5: new high speed USB device using ehci_hcd and address 3
[ 23.925029] usb 2-5: configuration #1 chosen from 1 choice
[ 23.963473] Initializing USB Mass Storage driver...
[ 23.964288] scsi6 : SCSI emulation for USB Mass Storage devices
[ 23.964454] usbcore: registered new interface driver usb-storage
[ 23.964457] USB Mass Storage support registered.
[ 23.965619] usb-storage: device found at 3
[ 23.965621] usb-storage: waiting for device to settle before scanning
[ 24.565378] NET: Registered protocol family 17
[ 26.130297] atkbd.c: Unknown key pressed (translated set 2, code 0x95 on isa0060/serio0).
[ 26.130297] atkbd.c: Use 'setkeycodes e015 <keycode>' to make it known.
[ 26.130462] atkbd.c: Unknown key released (translated set 2, code 0x95 on isa0060/serio0).
[ 26.130462] atkbd.c: Use 'setkeycodes e015 <keycode>' to make it known.
[ 26.247963] ACPI: EC: non-query interrupt received, switching to interrupt mode
[ 28.965258] usb-storage: device scan complete
[ 28.965597] scsi 6:0:0:0: Direct-Access CBM Flash Disk 5.00 PQ: 0 ANSI: 2
[ 28.978447] sd 6:0:0:0: [sdb] 257792 512-byte hardware sectors (132 MB)
[ 28.982239] sd 6:0:0:0: [sdb] Write Protect is off
[ 28.982243] sd 6:0:0:0: [sdb] Mode Sense: 0b 00 00 08
[ 28.982245] sd 6:0:0:0: [sdb] Assuming drive cache: write through
[ 28.984431] sd 6:0:0:0: [sdb] 257792 512-byte hardware sectors (132 MB)
[ 28.985075] sd 6:0:0:0: [sdb] Write Protect is off
[ 28.985075] sd 6:0:0:0: [sdb] Mode Sense: 0b 00 00 08
[ 28.985075] sd 6:0:0:0: [sdb] Assuming drive cache: write through
[ 28.985075] sdb: sdb1
[ 28.985840] sd 6:0:0:0: [sdb] Attached SCSI removable disk
[ 28.985840] sd 6:0:0:0: Attached scsi generic sg2 type 0
[ 105.379430] tun: Universal TUN/TAP device driver, 1.6
[ 105.379435] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 332.992622] warning: `ntpd' uses 32-bit capabilities (legacy support in use)
[ 499.178040] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 499.178105] ata1.00: cmd ca/00:3e:76:45:81/00:00:00:00:00/e1 tag 0 dma 31744 out
[ 499.178106] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 499.178168] ata1.00: status: { DRDY }
[ 499.178220] ata1: hard resetting link
[ 499.942034] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 499.943540] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded
[ 499.946056] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded
[ 499.947174] ata1.00: configured for UDMA/100
[ 499.947174] ata1: EH complete
[ 499.947443] sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors (100030 MB)
[ 499.947443] sd 0:0:0:0: [sda] Write Protect is off
[ 499.947443] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 499.947443] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 529.963038] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 529.963102] ata1.00: cmd ca/00:18:17:0b:94/00:00:00:00:00/e0 tag 0 dma 12288 out
[ 529.963103] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 529.963166] ata1.00: status: { DRDY }
[ 529.963217] ata1: hard resetting link
[ 530.778173] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 530.779373] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded
[ 530.781865] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded
[ 530.782983] ata1.00: configured for UDMA/100
[ 530.782983] ata1: EH complete
[ 530.784112] sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors (100030 MB)
[ 530.784232] sd 0:0:0:0: [sda] Write Protect is off
[ 530.784235] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 530.784474] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 560.791039] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 560.791104] ata1.00: cmd ca/00:28:1f:7f:99/00:00:00:00:00/e0 tag 0 dma 20480 out
[ 560.791106] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 560.791168] ata1.00: status: { DRDY }
[ 560.791219] ata1: hard resetting link
[ 561.606033] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 561.607234] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded
[ 561.609720] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded
[ 561.610838] ata1.00: configured for UDMA/100
[ 561.610838] ata1: EH complete
[ 561.611190] sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors (100030 MB)
[ 561.611354] sd 0:0:0:0: [sda] Write Protect is off
[ 561.611354] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 561.612087] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 682.780718] ieee80211_crypt: registered algorithm 'CCMP'
[ 683.768096] ieee80211_crypt: registered algorithm 'TKIP'
[ 814.838039] ata1: limiting SATA link speed to 1.5 Gbps
[ 814.838046] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 814.838109] ata1.00: cmd ca/00:10:57:b6:17/00:00:00:00:00/e2 tag 0 dma 8192 out
[ 814.838110] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 814.838172] ata1.00: status: { DRDY }
[ 814.838224] ata1: hard resetting link
[ 815.602032] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 815.603229] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded
[ 815.606466] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded
[ 815.607598] ata1.00: configured for UDMA/100
[ 815.607598] ata1: EH complete
[ 815.607806] sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors (100030 MB)
[ 815.607887] sd 0:0:0:0: [sda] Write Protect is off
[ 815.607887] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 815.608242] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 845.624027] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 845.624087] ata1.00: cmd ca/00:10:df:17:79/00:00:00:00:00/e0 tag 0 dma 8192 out
[ 845.624089] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 845.624150] ata1.00: status: { DRDY }
[ 845.624199] ata1: hard resetting link
[ 846.439166] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 846.440368] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded
[ 846.442863] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded
[ 846.443980] ata1.00: configured for UDMA/100
[ 846.443980] ata1: EH complete
[ 846.444412] sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors (100030 MB)
[ 846.444783] sd 0:0:0:0: [sda] Write Protect is off
[ 846.444783] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 846.444977] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 876.459037] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 876.459103] ata1.00: cmd ca/00:01:87:08:71/00:00:00:00:00/e3 tag 0 dma 512 out
[ 876.459105] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 876.459166] ata1.00: status: { DRDY }
[ 876.459218] ata1: hard resetting link
[ 877.325032] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 877.326233] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded
[ 877.329234] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded
[ 877.330350] ata1.00: configured for UDMA/100
[ 877.330350] ata1: EH complete
[ 877.334027] sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors (100030 MB)
[ 877.334086] sd 0:0:0:0: [sda] Write Protect is off
[ 877.334089] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 877.334125] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 970.438986] usb 2-5: USB disconnect, address 3
[ 1154.161035] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 1154.161100] ata1.00: cmd ca/00:30:2f:19:f6/00:00:00:00:00/e2 tag 0 dma 24576 out
[ 1154.161102] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 1154.161164] ata1.00: status: { DRDY }
[ 1154.161215] ata1: hard resetting link
[ 1154.772159] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1154.773358] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded
[ 1154.775851] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded
[ 1154.776967] ata1.00: configured for UDMA/100
[ 1154.776967] ata1: EH complete
[ 1154.777379] sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors (100030 MB)
[ 1154.777571] sd 0:0:0:0: [sda] Write Protect is off
[ 1154.777571] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1154.777766] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1186.493044] ata1.00: limiting speed to UDMA/66:PIO4
[ 1186.493050] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 1186.493113] ata1.00: cmd ca/00:10:17:25:f6/00:00:00:00:00/e2 tag 0 dma 8192 out
[ 1186.493115] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 1186.493177] ata1.00: status: { DRDY }
[ 1186.493228] ata1: hard resetting link
[ 1187.155167] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1187.156365] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded
[ 1187.158855] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded
[ 1187.159972] ata1.00: configured for UDMA/66
[ 1187.159972] ata1: EH complete
[ 1187.161154] sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors (100030 MB)
[ 1187.161283] sd 0:0:0:0: [sda] Write Protect is off
[ 1187.161286] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1187.161567] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1217.172036] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 1217.172098] ata1.00: cmd 35/00:00:47:01:f8/00:04:02:00:00/e0 tag 0 dma 524288 out
[ 1217.172100] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 1217.172162] ata1.00: status: { DRDY }
[ 1217.172212] ata1: hard resetting link
[ 1217.936036] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1217.937237] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded
[ 1217.940440] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded
[ 1217.941572] ata1.00: configured for UDMA/66
[ 1217.941572] ata1: EH complete
[ 1217.949939] sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors (100030 MB)
[ 1217.954021] sd 0:0:0:0: [sda] Write Protect is off
[ 1217.954021] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1217.961634] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1315.895050] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 1315.895088] ata1.00: cmd ca/00:20:d7:23:f8/00:00:00:00:00/e2 tag 0 dma 16384 out
[ 1315.895090] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 1315.895119] ata1.00: status: { DRDY }
[ 1315.895138] ata1: hard resetting link
[ 1316.557036] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1316.558237] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded
[ 1316.561473] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded
[ 1316.562606] ata1.00: configured for UDMA/66
[ 1316.562606] ata1: EH complete
[ 1316.562820] sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors (100030 MB)
[ 1316.562820] sd 0:0:0:0: [sda] Write Protect is off
[ 1316.562820] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1316.562820] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1346.570036] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 1346.570064] ata1.00: cmd ca/00:08:57:0a:49/00:00:00:00:00/e0 tag 0 dma 4096 out
[ 1346.570065] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 1346.570095] ata1.00: status: { DRDY }
[ 1346.570112] ata1: hard resetting link
[ 1347.334036] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1347.335237] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded
[ 1347.338409] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded
[ 1347.339542] ata1.00: configured for UDMA/66
[ 1347.339542] ata1: EH complete
[ 1347.339715] sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors (100030 MB)
[ 1347.339793] sd 0:0:0:0: [sda] Write Protect is off
[ 1347.339793] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1347.339976] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1377.351032] ata1.00: limiting speed to UDMA/33:PIO4
[ 1377.351036] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 1377.351063] ata1.00: cmd ca/00:08:cf:09:cd/00:00:00:00:00/e0 tag 0 dma 4096 out
[ 1377.351064] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 1377.351093] ata1.00: status: { DRDY }
[ 1377.351111] ata1: hard resetting link
[ 1378.166173] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1378.167377] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded
[ 1378.170232] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded
[ 1378.171349] ata1.00: configured for UDMA/33
[ 1378.171349] ata1: EH complete
[ 1378.171518] sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors (100030 MB)
[ 1378.171593] sd 0:0:0:0: [sda] Write Protect is off
[ 1378.171593] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1378.171656] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1408.178032] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 1408.178060] ata1.00: cmd ca/00:10:c7:94:f1/00:00:00:00:00/e2 tag 0 dma 8192 out
[ 1408.178061] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 1408.178090] ata1.00: status: { DRDY }
[ 1408.178108] ata1: hard resetting link
[ 1408.993173] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1408.994375] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded
[ 1408.996870] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded
[ 1408.997988] ata1.00: configured for UDMA/33
[ 1408.997988] ata1: EH complete
[ 1408.998203] sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors (100030 MB)
[ 1408.998340] sd 0:0:0:0: [sda] Write Protect is off
[ 1408.998340] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1408.998523] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1439.006036] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 1439.006066] ata1.00: cmd ca/00:10:27:13:91/00:00:00:00:00/e2 tag 0 dma 8192 out
[ 1439.006067] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 1439.006097] ata1.00: status: { DRDY }
[ 1439.006116] ata1: hard resetting link
[ 1439.821174] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1439.822375] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded
[ 1439.824872] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded
[ 1439.825988] ata1.00: configured for UDMA/33
[ 1439.825988] ata1: EH complete
[ 1439.826156] sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors (100030 MB)
[ 1439.826252] sd 0:0:0:0: [sda] Write Protect is off
[ 1439.826252] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1439.826488] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1469.836037] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 1469.836065] ata1.00: cmd ca/00:08:7f:4e:f8/00:00:00:00:00/e2 tag 0 dma 4096 out
[ 1469.836067] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 1469.836096] ata1.00: status: { DRDY }
[ 1469.836114] ata1: hard resetting link
[ 1470.651175] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1470.652376] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded
[ 1470.654877] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded
[ 1470.655994] ata1.00: configured for UDMA/33
[ 1470.655994] ata1: EH complete
[ 1470.656164] sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors (100030 MB)
[ 1470.656240] sd 0:0:0:0: [sda] Write Protect is off
[ 1470.656240] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1470.656398] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1500.664044] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 1500.664071] ata1.00: cmd ca/00:10:2f:72:f8/00:00:00:00:00/e2 tag 0 dma 8192 out
[ 1500.664072] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 1500.664101] ata1.00: status: { DRDY }
[ 1500.664119] ata1: hard resetting link
[ 1501.428036] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1501.429237] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded
[ 1501.432423] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded
[ 1501.433555] ata1.00: configured for UDMA/33
[ 1501.433555] ata1: EH complete
[ 1501.433855] sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors (100030 MB)
[ 1501.433951] sd 0:0:0:0: [sda] Write Protect is off
[ 1501.433951] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1501.434106] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1531.443037] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 1531.443064] ata1.00: cmd ca/00:08:e7:91:f8/00:00:00:00:00/e2 tag 0 dma 4096 out
[ 1531.443066] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 1531.443095] ata1.00: status: { DRDY }
[ 1531.443112] ata1: hard resetting link
[ 1532.207034] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1532.208235] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded
[ 1532.211421] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded
[ 1532.212554] ata1.00: configured for UDMA/33
[ 1532.212554] ata1: EH complete
[ 1532.212758] sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors (100030 MB)
[ 1532.212867] sd 0:0:0:0: [sda] Write Protect is off
[ 1532.212867] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1532.213025] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1562.219036] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 1562.219064] ata1.00: cmd ca/00:08:2f:ac:f8/00:00:00:00:00/e2 tag 0 dma 4096 out
[ 1562.219066] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 1562.219095] ata1.00: status: { DRDY }
[ 1562.219113] ata1: hard resetting link
[ 1562.983062] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1562.984249] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded
[ 1562.987424] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded
[ 1562.988556] ata1.00: configured for UDMA/33
[ 1562.988556] ata1: EH complete
[ 1562.988748] sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors (100030 MB)
[ 1562.988851] sd 0:0:0:0: [sda] Write Protect is off
[ 1562.988851] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1562.989049] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1592.996034] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 1592.996062] ata1.00: cmd ca/00:10:5f:c9:f8/00:00:00:00:00/e2 tag 0 dma 8192 out
[ 1592.996063] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 1592.996093] ata1.00: status: { DRDY }
[ 1592.996110] ata1: hard resetting link
[ 1593.760172] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1593.761372] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded
[ 1593.763862] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded
[ 1593.764977] ata1.00: configured for UDMA/33
[ 1593.764977] ata1: EH complete
[ 1593.765183] sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors (100030 MB)
[ 1593.765206] sd 0:0:0:0: [sda] Write Protect is off
[ 1593.765206] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1593.765206] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1617.738192] usb 2-5: new high speed USB device using ehci_hcd and address 4
[ 1617.852903] usb 2-5: configuration #1 chosen from 1 choice
[ 1617.859032] scsi7 : SCSI emulation for USB Mass Storage devices
[ 1617.862832] usb-storage: device found at 4
[ 1617.862834] usb-storage: waiting for device to settle before scanning
[ 1622.862353] usb-storage: device scan complete
[ 1622.862703] scsi 7:0:0:0: Direct-Access CBM Flash Disk 5.00 PQ: 0 ANSI: 2
[ 1622.864004] sd 7:0:0:0: [sdb] 257792 512-byte hardware sectors (132 MB)
[ 1622.864615] sd 7:0:0:0: [sdb] Write Protect is off
[ 1622.864618] sd 7:0:0:0: [sdb] Mode Sense: 0b 00 00 08
[ 1622.864621] sd 7:0:0:0: [sdb] Assuming drive cache: write through
[ 1622.866735] sd 7:0:0:0: [sdb] 257792 512-byte hardware sectors (132 MB)
[ 1622.867362] sd 7:0:0:0: [sdb] Write Protect is off
[ 1622.867365] sd 7:0:0:0: [sdb] Mode Sense: 0b 00 00 08
[ 1622.867367] sd 7:0:0:0: [sdb] Assuming drive cache: write through
[ 1622.867420] sdb: sdb1
[ 1622.868538] sd 7:0:0:0: [sdb] Attached SCSI removable disk
[ 1622.868580] sd 7:0:0:0: Attached scsi generic sg2 type 0
next prev parent reply other threads:[~2008-07-02 9:04 UTC|newest]
Thread overview: 8+ messages / expand[flat|nested] mbox.gz Atom feed top
2008-07-01 9:39 2.6.25 to 2.6.26-rc8 regression (related to ahci and acpi _GTF) Mathieu Bérard
2008-07-01 14:14 ` Rafael J. Wysocki
2008-07-01 14:14 ` Rafael J. Wysocki
2008-07-02 2:55 ` Tejun Heo
2008-07-02 2:55 ` Tejun Heo
2008-07-02 9:04 ` Mathieu Bérard [this message]
2008-07-04 4:36 ` Tejun Heo
2008-07-04 16:08 ` Mathieu Bérard
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=486B4490.7080904@crans.org \
--to=mathieu.berard@crans.org \
--cc=akpm@linux-foundation.org \
--cc=andi@firstfloor.org \
--cc=htejun@gmail.com \
--cc=jeff@garzik.org \
--cc=linux-acpi@vger.kernel.org \
--cc=linux-ide@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=rjw@sisk.pl \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.