From: Julian Picht <julian@summer06.de>
To: linux-dvb@linuxtv.org
Subject: [linux-dvb] Terratec Cinergy S PCI
Date: Thu, 03 Jul 2008 11:21:54 +0200 [thread overview]
Message-ID: <486C9A32.3010904@summer06.de> (raw)
Hi List.
I recently bought a Terratec Cinergy S PCI which uses a Conexant CX2388x
chip as it's PCI Interface and a Fujitsu MB86A16 as it's frontend.
I modified the cx88 files to recognize this card. Now I need a some
pointers how to attach the MB86A16 frontend (which is included in mantis
source, i think) to the cx88 and how to obtain the right i2c adresses etc.
Is there any documentation on how to do that?
I would be very happy to contribute to the great work you do and already
did.
--------------------------------------
# lspci -vvnn
04:01.0 Multimedia video controller [0400]: Conexant CX23880/1/2/3 PCI
Video and Audio Decoder [14f1:8800] (rev 05)
Subsystem: TERRATEC Electronic GmbH Device [153b:117a]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (5000ns min, 13750ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 22
Region 0: Memory at fb000000 (32-bit, non-prefetchable) [size=16M]
Capabilities: <access denied>
Kernel driver in use: cx8800
Kernel modules: cx8800
04:01.2 Multimedia controller [0480]: Conexant CX23880/1/2/3 PCI Video
and Audio Decoder [MPEG Port] [14f1:8802] (rev 05)
Subsystem: TERRATEC Electronic GmbH Device [153b:117a]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (1500ns min, 22000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 5
Region 0: Memory at fc000000 (32-bit, non-prefetchable) [size=16M]
Capabilities: <access denied>
Kernel modules: cx8802
04:01.4 Multimedia controller [0480]: Conexant CX23880/1/2/3 PCI Video
and Audio Decoder [IR Port] [14f1:8804] (rev 05)
Subsystem: TERRATEC Electronic GmbH Device [153b:117a]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (1500ns min, 63750ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 5
Region 0: Memory at fd000000 (32-bit, non-prefetchable) [size=16M]
Capabilities: <access denied>
--------------------------------------
# i2cdetect -l
i2c-0 smbus SMBus I801 adapter at 0400 SMBus adapter
i2c-1 i2c cx88[0] I2C adapter
# i2cdetect 1
WARNING! This program can confuse your I2C bus, cause data loss and worse!
I will probe file /dev/i2c-1.
I will probe address range 0x03-0x77.
Continue? [Y/n]
0 1 2 3 4 5 6 7 8 9 a b c d e f
00: -- -- -- -- -- 08 -- -- -- -- -- -- --
10: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
20: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
30: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
40: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
50: UU -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
60: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
70: -- -- -- -- -- -- -- --
--------------------------------------
Thanks in advance! Any help appreciated!
Julian Picht
_______________________________________________
linux-dvb mailing list
linux-dvb@linuxtv.org
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
next reply other threads:[~2008-07-03 9:22 UTC|newest]
Thread overview: 3+ messages / expand[flat|nested] mbox.gz Atom feed top
2008-07-03 9:21 Julian Picht [this message]
2008-07-13 13:52 ` [linux-dvb] Terratec Cinergy S PCI Julian Picht
-- strict thread matches above, loose matches on Subject: below --
2008-12-16 20:54 Stefan Ubben
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=486C9A32.3010904@summer06.de \
--to=julian@summer06.de \
--cc=linux-dvb@linuxtv.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.