All of lore.kernel.org
 help / color / mirror / Atom feed
From: Patrick Boisvenue <patrbois@magma.ca>
To: linux-dvb@linuxtv.org
Subject: [linux-dvb] HVR-1500Q eeprom not being parsed correctly
Date: Tue, 09 Sep 2008 07:11:01 -0400	[thread overview]
Message-ID: <48C659C5.8000902@magma.ca> (raw)

I cannot get my new HVR-1500Q to work at all even though it's recognized 
as such.  The best I was able to figure out was it does not like the 
eeprom.  After enabling the debug mode on tveeprom, I got the following 
when loading cx23885:

cx23885 driver version 0.0.1 loaded
cx23885 0000:05:00.0: enabling device (0000 -> 0002)
ACPI: PCI Interrupt 0000:05:00.0[A] -> GSI 19 (level, low) -> IRQ 19
CORE cx23885[0]: subsystem: 0070:7790, board: Hauppauge WinTV-HVR1500Q 
[card=5,autodetected]
cx23885[0]: i2c bus 0 registered
cx23885[0]: i2c bus 1 registered
cx23885[0]: i2c bus 2 registered
tveeprom 1-0050: full 256-byte eeprom dump:
tveeprom 1-0050: 00: 20 00 13 00 00 00 00 00 2c 00 05 00 70 00 90 77
tveeprom 1-0050: 10: 50 03 05 00 04 80 00 08 0c 03 05 80 0e 01 00 00
tveeprom 1-0050: 20: 78 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
tveeprom 1-0050: 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
tveeprom 1-0050: 40: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
tveeprom 1-0050: 50: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
tveeprom 1-0050: 60: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
tveeprom 1-0050: 70: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
tveeprom 1-0050: 80: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
tveeprom 1-0050: 90: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
tveeprom 1-0050: a0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
tveeprom 1-0050: b0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
tveeprom 1-0050: c0: 84 09 00 04 20 77 00 40 ec 66 25 f0 73 05 27 00
tveeprom 1-0050: d0: 84 08 00 06 fb 2c 01 00 90 29 95 72 07 70 73 09
tveeprom 1-0050: e0: 21 7f 73 0a 88 96 72 0b 13 72 10 01 72 11 ff 79
tveeprom 1-0050: f0: dc 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
tveeprom 1-0050: Encountered bad packet header [ff]. Corrupt or not a 
Hauppauge eeprom.
cx23885[0]: warning: unknown hauppauge model #0
cx23885[0]: hauppauge eeprom: model=0
cx23885[0]: cx23885 based dvb card
xc5000: Successfully identified at address 0x61
xc5000: Firmware has not been loaded previously
DVB: registering new adapter (cx23885[0])
DVB: registering frontend 0 (Samsung S5H1409 QAM/8VSB Frontend)...
cx23885_dev_checkrevision() Hardware revision = 0xb0
cx23885[0]/0: found at 0000:05:00.0, rev: 2, irq: 19, latency: 0, mmio: 
0xd4000000
PCI: Setting latency timer of device 0000:05:00.0 to 64

Did a hg pull -u http://linuxtv.org/hg/v4l-dvb earlier today so running 
off recent codebase.

Any suggestions,
...Patrick


_______________________________________________
linux-dvb mailing list
linux-dvb@linuxtv.org
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb

             reply	other threads:[~2008-09-09 11:11 UTC|newest]

Thread overview: 22+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2008-09-09 11:11 Patrick Boisvenue [this message]
2008-09-09 14:52 ` [linux-dvb] HVR-1500Q eeprom not being parsed correctly Steven Toth
2008-09-10  2:30   ` Patrick Boisvenue
2008-09-10  2:37     ` Steven Toth
2008-09-10  3:56       ` barry bouwsma
2008-09-10 11:45       ` Patrick Boisvenue
2008-09-10 18:34         ` Steven Toth
2008-09-10 22:55       ` Andy Walls
2008-09-11  0:37         ` Patrick Boisvenue
2008-09-11  1:10           ` Andy Walls
2008-09-12 18:24             ` Patrick Boisvenue
2008-09-12 18:41               ` Michael Krufky
2008-09-12 19:12                 ` Patrick Boisvenue
2008-09-12 19:16                   ` Patrick Boisvenue
2008-09-13  1:25                     ` Andy Walls
2008-09-15 16:35                       ` Markus Rechberger
2008-09-16 12:05                         ` Patrick Boisvenue
2008-09-16 23:35                           ` Andy Walls
2008-10-23 10:21                             ` Oldrich Jedlicka
2008-09-15 16:30                   ` Michael Krufky
2008-09-10 23:46     ` Steven Toth
  -- strict thread matches above, loose matches on Subject: below --
2008-09-09 21:01 Tim Lucas

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=48C659C5.8000902@magma.ca \
    --to=patrbois@magma.ca \
    --cc=linux-dvb@linuxtv.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body. 
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.