Re: [PATCH] cs89x0: add support for i.MX31ADS ARM board

[Jeff Garzik <jeff@garzik.org>]

Gilles Chanteperdrix wrote:
> Signed-off-by: Gilles Chanteperdrix <gilles.chanteperdrix@xenomai.org>
> ---
> diff --git a/drivers/net/cs89x0.c b/drivers/net/cs89x0.c
> index ea6144a..875a43d 100644
> --- a/drivers/net/cs89x0.c
> +++ b/drivers/net/cs89x0.c
> @@ -194,6 +194,12 @@ static unsigned int cs8900_irq_map[] = {IRQ_IXDP2X01_CS8900, 0, 0, 0};
>  #define CIRRUS_DEFAULT_IRQ	VH_INTC_INT_NUM_CASCADED_INTERRUPT_1 /* Event inputs bank 1 - ID 35/bit 3 */
>  static unsigned int netcard_portlist[] __used __initdata = {CIRRUS_DEFAULT_BASE, 0};
>  static unsigned int cs8900_irq_map[] = {CIRRUS_DEFAULT_IRQ, 0, 0, 0};
> +#elif defined(CONFIG_MACH_MX31ADS)
> +#include <mach/board-mx31ads.h>
> +static unsigned int netcard_portlist[] __used __initdata = {
> +	PBC_BASE_ADDRESS + PBC_CS8900A_IOBASE + 0x300, 0
> +};
> +static unsigned cs8900_irq_map[] = {EXPIO_INT_ENET_INT, 0, 0, 0};
>  #else
>  static unsigned int netcard_portlist[] __used __initdata =
>     { 0x300, 0x320, 0x340, 0x360, 0x200, 0x220, 0x240, 0x260, 0x280, 0x2a0, 0x2c0, 0x2e0, 0};
> @@ -802,7 +808,7 @@ cs89x0_probe1(struct net_device *dev, int ioaddr, int modular)
>  	} else {
>  		i = lp->isa_config & INT_NO_MASK;
>  		if (lp->chip_type == CS8900) {
> -#if defined(CONFIG_MACH_IXDP2351) || defined(CONFIG_ARCH_IXDP2X01) || defined(CONFIG_ARCH_PNX010X)
> +#if defined(CONFIG_MACH_IXDP2351) || defined(CONFIG_ARCH_IXDP2X01) || defined(CONFIG_ARCH_PNX010X) || defined(CONFIG_MACH_MX31ADS)
>  		        i = cs8900_irq_map[0];
>  #else
>  			/* Translate the IRQ using the IRQ mapping table. */
> @@ -1029,6 +1035,7 @@ skip_this_frame:
>  
>  void  __init reset_chip(struct net_device *dev)
>  {
> +#if !defined(CONFIG_MACH_MX31ADS)
>  #if !defined(CONFIG_MACH_IXDP2351) && !defined(CONFIG_ARCH_IXDP2X01)
>  	struct net_local *lp = netdev_priv(dev);
>  	int ioaddr = dev->base_addr;
> @@ -1057,6 +1064,7 @@ void  __init reset_chip(struct net_device *dev)
>  	reset_start_time = jiffies;
>  	while( (readreg(dev, PP_SelfST) & INIT_DONE) == 0 && jiffies - reset_start_time < 2)
>  		;
> +#endif /* !CONFIG_MACH_MX31ADS */
>  }
>  
>  
> @@ -1304,7 +1312,7 @@ net_open(struct net_device *dev)
>  	else
>  #endif
>  	{
> -#if !defined(CONFIG_MACH_IXDP2351) && !defined(CONFIG_ARCH_IXDP2X01) && !defined(CONFIG_ARCH_PNX010X)
> +#if !defined(CONFIG_MACH_IXDP2351) && !defined(CONFIG_ARCH_IXDP2X01) && !defined(CONFIG_ARCH_PNX010X) && !defined(CONFIG_MACH_MX31ADS)
>  		if (((1 << dev->irq) & lp->irq_map) == 0) {
>  			printk(KERN_ERR "%s: IRQ %d is not in our map of allowable IRQs, which is %x\n",

I don't know enough about the arch to be able to ACK or NAK...  pass 
this through the appropriate arch maintainer tree please?