From: Stuart Johnson <stuart@stu.org.uk>
To: linux-dvb@linuxtv.org
Subject: [linux-dvb] FATAL: Error inserting cx88_dvb
Date: Fri, 26 Sep 2008 15:19:25 +0100 [thread overview]
Message-ID: <48DCEF6D.6030407@stu.org.uk> (raw)
[-- Attachment #1.1: Type: text/plain, Size: 4491 bytes --]
I have 2 x WinTV-HS-S2 DVB-S & a Nebula DVB-T PCI adaptors.
I am only getting the frontend on the DVB-T
#modprobe -i cx88-dvb
FATAL: Error inserting cx88_dvb
(/lib/modules/2.6.26.1/kernel/drivers/media/video/cx88/cx88-dvb.ko):
Unknown symbol in module, or unknown parameter (see dmesg)
#dmesg
Linux video capture interface: v2.00
cx88/0: cx2388x v4l2 driver version 0.0.6 loaded
cx88/2: cx2388x MPEG-TS Driver Manager version 0.0.6 loaded
bttv: driver version 0.9.17 loaded
bttv: using 8 buffers with 2080k (520 pages) each for capture
PCI: Disallowing DAC for device 0000:00:0a.0
eth0: Tigon3 [partno(284685-003) rev 0105 PHY(5701)] (PCI:33MHz:32-bit)
10/100/1000Base-T Ethernet 00:0f:20:d7:1d:2c
eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] WireSpeed[1] TSOcap[0]
eth0: dma_rwctrl[76ff000f] dma_mask[32-bit]
bttv: Bt8xx card found (0).
bttv0: Bt878 (rev 17) at 0000:00:09.0, irq: 3, latency: 32, mmio: 0xf9000000
bttv0: detected: Nebula Electronics DigiTV [card=104], PCI subsystem ID
is 0071:0101
bttv0: using: Nebula Electronics DigiTV [card=104,autodetected]
bttv0: gpio: en=00000000, out=00000000 in=00ff00cb [init]
bttv0: tuner absent
bttv0: registered device video0
bttv0: registered device vbi0
bttv0: PLL: 28636363 => 35468950 .. ok
bttv0: add subdevice "dvb0"
input: bttv IR (card=104) as /devices/pci0000:00/0000:00:09.0/input/input1
cx88[0]: subsystem: 0070:6906, board: Hauppauge WinTV-HVR4000(Lite)
DVB-S/S2 [card=69,autodetected]
cx88[0]: TV tuner type -1, Radio tuner type -1
bt878: gave up waiting for init of module bttv.
bt878: Unknown symbol bttv_read_gpio
bt878: gave up waiting for init of module bttv.
bt878: Unknown symbol bttv_write_gpio
Filesystem "md4": Disabling barriers, not supported by the underlying device
XFS mounting filesystem md4
Ending clean XFS mount for filesystem: md4
XFS mounting filesystem hde1
Ending clean XFS mount for filesystem: hde1
XFS mounting filesystem hdg1
Ending clean XFS mount for filesystem: hdg1
Adding 240888k swap on /dev/md2. Priority:-1 extents:1 across:240888k
hda: UDMA/100 mode selected
hdc: UDMA/100 mode selected
hde: UDMA/100 mode selected
hdg: UDMA/100 mode selected
bt878: gave up waiting for init of module bttv.
bt878: Unknown symbol bttv_gpio_enable
tveeprom 2-0050: Hauppauge model 69100, rev B2C3, serial# 3247319
tveeprom 2-0050: MAC address is 00-0D-FE-31-8C-D7
tveeprom 2-0050: tuner model is Conexant CX24118A (idx 123, type 4)
tveeprom 2-0050: TV standards ATSC/DVB Digital (eeprom 0x80)
tveeprom 2-0050: audio processor is None (idx 0)
tveeprom 2-0050: decoder processor is CX882 (idx 25)
tveeprom 2-0050: has no radio, has IR receiver, has no IR transmitter
cx88[0]: hauppauge eeprom: model=69100
input: cx88 IR (Hauppauge WinTV-HVR400 as
/devices/pci0000:00/0000:00:0b.0/input/input2
cx88[0]/0: found at 0000:00:0b.0, rev: 5, irq: 10, latency: 32, mmio:
0xf5000000
cx88[0]/0: registered device video1 [v4l2]
cx88[0]/0: registered device vbi1
cx88[0]/2: cx2388x 8802 Driver Manager
cx88[0]/2: found at 0000:00:0b.2, rev: 5, irq: 10, latency: 32, mmio:
0xf3000000
udev: renamed network interface eth0 to eth1
cx88[1]: subsystem: 0070:6906, board: Hauppauge WinTV-HVR4000(Lite)
DVB-S/S2 [card=69,autodetected]
cx88[1]: TV tuner type -1, Radio tuner type -1
tveeprom 3-0050: Hauppauge model 69100, rev B2C3, serial# 3247400
tveeprom 3-0050: MAC address is 00-0D-FE-31-8D-28
tveeprom 3-0050: tuner model is Conexant CX24118A (idx 123, type 4)
tveeprom 3-0050: TV standards ATSC/DVB Digital (eeprom 0x80)
tveeprom 3-0050: audio processor is None (idx 0)
tveeprom 3-0050: decoder processor is CX882 (idx 25)
tveeprom 3-0050: has no radio, has IR receiver, has no IR transmitter
cx88[1]: hauppauge eeprom: model=69100
input: cx88 IR (Hauppauge WinTV-HVR400 as
/devices/pci0000:00/0000:00:0d.0/input/input3
cx88[1]/0: found at 0000:00:0d.0, rev: 5, irq: 3, latency: 32, mmio:
0xf0000000
cx88[1]/0: registered device video2 [v4l2]
cx88[1]/0: registered device vbi2
cx88[1]/2: cx2388x 8802 Driver Manager
cx88[1]/2: found at 0000:00:0d.2, rev: 5, irq: 3, latency: 32, mmio:
0xee000000
bt878: AUDIO driver version 0.0.0 loaded
bt878: Bt878 AUDIO function found (0).
bt878_probe: card id=[0x1010071],[ Nebula Electronics DigiTV ] has DVB
functions.
bt878(0): Bt878 (rev 17) at 00:09.1, irq: 3, latency: 32, memory: 0xf8800000
DVB: registering new adapter (bttv0)
cx88_dvb: Unknown parameter `frontend'
DVB: registering frontend 0 (NxtWave NXT6000 DVB-T)...
cx88_dvb: Unknown parameter `frontend'
[-- Attachment #1.2: Type: text/html, Size: 5021 bytes --]
[-- Attachment #2: Type: text/plain, Size: 150 bytes --]
_______________________________________________
linux-dvb mailing list
linux-dvb@linuxtv.org
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
reply other threads:[~2008-09-26 14:19 UTC|newest]
Thread overview: [no followups] expand[flat|nested] mbox.gz Atom feed
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=48DCEF6D.6030407@stu.org.uk \
--to=stuart@stu.org.uk \
--cc=linux-dvb@linuxtv.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.