All of lore.kernel.org
 help / color / mirror / Atom feed
From: David Greaves <david@dgreaves.com>
To: Smartmontools Mailing List
	<smartmontools-support@lists.sourceforge.net>,
	linux-kernel@vger.kernel.org, linux-ide@vger.kernel.org
Subject: SMART to USB/sata dock in 2.6.27-rc5 doesn't work
Date: Thu, 09 Oct 2008 22:56:26 +0100	[thread overview]
Message-ID: <48EE7E0A.8040701@dgreaves.com> (raw)

Hi

I just bought a usb/sata adapter like this:
  http://www.thinkgeek.com/computing/drives/a7ea/?cpg=ab
lsusb -v is below

Works OK as a hot-plug SATA disk so I can check what's on that old disk in the
corner; but smartctl doesn't work so I can't see if it has any errors, run
selftests etc.

Kernel is 2.6.27-rc5 (I've also tried older kernels)

I plugged a previously zeroed drive in and...

root@ash:~ # smartctl -a /dev/sde
smartctl version 5.38 [i686-pc-linux-gnu] Copyright (C) 2002-8 Bruce Allen
Home page is http://smartmontools.sourceforge.net/

Device: ST332062 0AS              Version:
Device type: disk
Local Time is: Thu Oct  9 21:38:16 2008 BST
Device supports SMART and is Enabled
Temperature Warning Disabled or Not Supported
SMART Health Status: OK

Error Counter logging not supported
Device does not support Self Test logging


I've tried -dscsi and -dsat but they don't work.

More info below.

David


dmesg tail:
Initializing USB Mass Storage driver...
scsi8 : SCSI emulation for USB Mass Storage devices
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
scsi 8:0:0:0: Direct-Access     ST332062 0AS                   PQ: 0 ANSI: 2
sd 8:0:0:0: [sde] 625134827 512-byte hardware sectors (320069 MB)
sd 8:0:0:0: [sde] Write Protect is off
sd 8:0:0:0: [sde] Mode Sense: 38 00 00 00
sd 8:0:0:0: [sde] Assuming drive cache: write through
sd 8:0:0:0: [sde] 625134827 512-byte hardware sectors (320069 MB)
sd 8:0:0:0: [sde] Write Protect is off
sd 8:0:0:0: [sde] Mode Sense: 38 00 00 00
sd 8:0:0:0: [sde] Assuming drive cache: write through
 sde: unknown partition table
sd 8:0:0:0: [sde] Attached SCSI disk
sd 8:0:0:0: Attached scsi generic sg6 type 0

root@ash:~ # lsusb -v -s3:3

Bus 003 Device 003: ID 04fc:0c25 Sunplus Technology Co., Ltd
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               2.00
  bDeviceClass            0 (Defined at Interface level)
  bDeviceSubClass         0
  bDeviceProtocol         0
  bMaxPacketSize0        64
  idVendor           0x04fc Sunplus Technology Co., Ltd
  idProduct          0x0c25
  bcdDevice            1.03
  iManufacturer           2 Sunplus Technology Inc.
  iProduct                3 USB to Serial-ATA bridge
  iSerial                 1 SAMSUNG HD472712CQ696126
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           32
    bNumInterfaces          1
    bConfigurationValue     1
    iConfiguration          4 Bulk Only Configuration
    bmAttributes         0xc0
      Self Powered
    MaxPower                2mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           2
      bInterfaceClass         8 Mass Storage
      bInterfaceSubClass      6 SCSI
      bInterfaceProtocol     80 Bulk (Zip)
      iInterface              5 Bulk Only Interface
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0200  1x 512 bytes
        bInterval               0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x02  EP 2 OUT
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0200  1x 512 bytes
        bInterval               0
Device Qualifier (for other device speed):
  bLength                10
  bDescriptorType         6
  bcdUSB               2.00
  bDeviceClass            0 (Defined at Interface level)
  bDeviceSubClass         0
  bDeviceProtocol         0
  bMaxPacketSize0        64
  bNumConfigurations      1
Device Status:     0x0001
  Self Powered



-- 
"Don't worry, you'll be fine; I saw it work in a cartoon once..."

             reply	other threads:[~2008-10-09 21:56 UTC|newest]

Thread overview: 11+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2008-10-09 21:56 David Greaves [this message]
2008-10-10  8:09 ` SMART to USB/sata dock in 2.6.27-rc5 doesn't work : hardware limitation David Greaves
2008-10-14  2:18 ` SMART to USB/sata dock in 2.6.27-rc5 doesn't work Tejun Heo
2008-10-15 19:16   ` [smartmontools-support] " matthieu castet
2008-10-23 16:04     ` Mark Lord
2008-10-23 18:58       ` matthieu castet
2008-10-23 20:21         ` Mark Lord
2008-10-23 20:36           ` Mark Lord
2008-10-24 18:54             ` matthieu castet
2008-10-25 12:46               ` Mark Lord
2008-10-23 16:01   ` Mark Lord

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=48EE7E0A.8040701@dgreaves.com \
    --to=david@dgreaves.com \
    --cc=linux-ide@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=smartmontools-support@lists.sourceforge.net \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.