From: Damazy <damazy@gmail.com>
To: Tejun Heo <tj@kernel.org>
Cc: jgarzik@pobox.com, linux-ide@vger.kernel.org
Subject: Re: sata_sil for 3512A chip on kernel 2.6.26.3
Date: Wed, 15 Oct 2008 08:37:50 +0200 [thread overview]
Message-ID: <48F58FBE.909@gmail.com> (raw)
In-Reply-To: <48F54E4C.1020704@kernel.org>
[-- Attachment #1: Type: text/plain, Size: 11047 bytes --]
Tejun Heo wrote:
>
> The commands are either being timed out or aborted by the device. Can
> you post the result of "smartctl -a" of the drive?
>
This is output of smartctl -a /dev/sda1
smartctl version 5.38 [i686-pc-linux-gnu] Copyright (C) 2002-8 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Device Model: SAMSUNG HD502IJ
Serial Number: S13TJ90Q641644
Firmware Version: 1AA01112
User Capacity: 500,106,780,160 bytes
Device is: In smartctl database [for details use: -P show]
ATA Version is: 8
ATA Standard is: ATA-8-ACS revision 3b
Local Time is: Wed Oct 15 08:32:29 2008 CEST
==> WARNING: May need -F samsung or -F samsung2 enabled; see manual for
details.
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection:
Disabled.
Self-test execution status: ( 0) The previous self-test routine
completed
without error or no self-test
has ever
been run.
Total time to complete Offline
data collection: (7461) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection
on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 125) minutes.
Conveyance self-test routine
recommended polling time: ( 14) minutes.
SCT capabilities: (0x003f) SCT Status supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE
UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 100 100 051 Pre-fail
Always - 0
3 Spin_Up_Time 0x0007 087 087 011 Pre-fail
Always - 4870
4 Start_Stop_Count 0x0032 100 100 000 Old_age
Always - 47
5 Reallocated_Sector_Ct 0x0033 100 100 010 Pre-fail
Always - 0
7 Seek_Error_Rate 0x000f 253 253 051 Pre-fail
Always - 0
8 Seek_Time_Performance 0x0025 100 100 015 Pre-fail
Offline - 9770
9 Power_On_Hours 0x0032 100 100 000 Old_age
Always - 1178
10 Spin_Retry_Count 0x0033 100 100 051 Pre-fail
Always - 0
11 Calibration_Retry_Count 0x0012 100 100 000 Old_age
Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age
Always - 46
13 Read_Soft_Error_Rate 0x000e 100 100 000 Old_age
Always - 0
183 Unknown_Attribute 0x0032 100 100 000 Old_age Always
- 0
184 Unknown_Attribute 0x0033 100 100 099 Pre-fail Always
- 0
187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always
- 0
188 Unknown_Attribute 0x0032 100 100 000 Old_age Always
- 0
190 Airflow_Temperature_Cel 0x0022 063 060 000 Old_age Always
- 37 (Lifetime Min/Max 35/40)
194 Temperature_Celsius 0x0022 063 059 000 Old_age Always
- 37 (Lifetime Min/Max 35/41)
195 Hardware_ECC_Recovered 0x001a 100 100 000 Old_age Always
- 115423
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always
- 0
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always
- 0
198 Offline_Uncorrectable 0x0030 100 100 000 Old_age
Offline - 0
199 UDMA_CRC_Error_Count 0x003e 099 099 000 Old_age Always
- 311
200 Multi_Zone_Error_Rate 0x000a 100 100 000 Old_age Always
- 0
201 Soft_Read_Error_Rate 0x000a 253 253 000 Old_age Always
- 0
SMART Error Log Version: 1
ATA Error Count: 190 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 190 occurred at disk power-on lifetime: 0 hours (0 days + 0 hours)
When the command that caused the error occurred, the device was
active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 3f 00 ee 1d e0 Error: ICRC, ABRT 63 sectors at LBA =
0x001dee00 = 1961472
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 00 3f ed 1d e0 00 00:50:52.250 READ DMA
c8 00 00 3f ec 1d e0 00 00:50:52.250 READ DMA
c8 00 00 3f eb 1d e0 00 00:50:52.250 READ DMA
c8 00 00 3f ea 1d e0 00 00:50:52.250 READ DMA
c8 00 00 3f e9 1d e0 00 00:50:52.250 READ DMA
Error 189 occurred at disk power-on lifetime: 0 hours (0 days + 0 hours)
When the command that caused the error occurred, the device was
active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 9f 58 db 1c e0 Error: ICRC, ABRT 159 sectors at LBA =
0x001cdb58 = 1891160
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 00 f7 da 1c e0 00 00:50:45.810 READ DMA
c8 00 00 f7 d9 1c e0 00 00:50:45.810 READ DMA
c8 00 00 f7 d8 1c e0 00 00:50:45.810 READ DMA
c8 00 00 f7 d7 1c e0 00 00:50:45.810 READ DMA
c8 00 00 f7 d6 1c e0 00 00:50:45.800 READ DMA
Error 188 occurred at disk power-on lifetime: 0 hours (0 days + 0 hours)
When the command that caused the error occurred, the device was
active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
00 d0 00 00 00 00 a0 at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 00 3f c5 1a e0 00 00:50:38.500 READ DMA
c8 00 00 3f c4 1a e0 00 00:50:38.490 READ DMA
ca 00 08 df d1 e9 ea 00 00:50:38.480 WRITE DMA
ca 00 08 d7 b1 e9 ea 00 00:50:38.480 WRITE DMA
ca 00 08 cf 91 e9 ea 00 00:50:38.480 WRITE DMA
Error 187 occurred at disk power-on lifetime: 0 hours (0 days + 0 hours)
When the command that caused the error occurred, the device was
active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 4f d0 35 1a e0 Error: ICRC, ABRT 79 sectors at LBA =
0x001a35d0 = 1717712
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 00 1f 35 1a e0 00 00:50:32.800 READ DMA
c8 00 80 9f 34 1a e0 00 00:50:32.790 READ DMA
c8 00 88 17 34 1a e0 00 00:50:32.790 READ DMA
c8 00 00 17 33 1a e0 00 00:50:32.790 READ DMA
c8 00 00 17 32 1a e0 00 00:50:32.790 READ DMA
Error 186 occurred at disk power-on lifetime: 0 hours (0 days + 0 hours)
When the command that caused the error occurred, the device was
active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 1f d0 66 16 e0 Error: ICRC, ABRT 31 sectors at LBA =
0x001666d0 = 1468112
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 00 ef 65 16 e0 00 00:50:28.720 READ DMA
c8 00 00 ef 64 16 e0 00 00:50:28.720 READ DMA
c8 00 00 ef 63 16 e0 00 00:50:28.720 READ DMA
c8 00 80 6f 63 16 e0 00 00:50:28.720 READ DMA
c8 00 88 e7 62 16 e0 00 00:50:28.710 READ DMA
SMART Self-test log structure revision number 0
Warning: ATA Specification requires self-test log structure revision
number = 1
Num Test_Description Status Remaining
LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed without error 00% 529
-
# 2 Short offline Aborted by host 00% 458
-
SMART Selective Self-Test Log Data Structure Revision Number (0) should be 1
SMART Selective self-test log data structure revision number 0
Warning: ATA Specification requires selective self-test log data
structure revision number = 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Kind regards.
[-- Attachment #2: S/MIME Cryptographic Signature --]
[-- Type: application/x-pkcs7-signature, Size: 3828 bytes --]
next prev parent reply other threads:[~2008-10-15 6:37 UTC|newest]
Thread overview: 10+ messages / expand[flat|nested] mbox.gz Atom feed top
2008-10-02 8:53 sata_sil for 3512A chip on kernel 2.6.26.3 Damazy
2008-10-04 7:39 ` Tejun Heo
2008-10-14 10:49 ` Damazy
2008-10-15 1:58 ` Tejun Heo
2008-10-15 6:37 ` Damazy [this message]
2008-10-15 6:46 ` Tejun Heo
2008-10-15 7:03 ` Damazy
2008-10-15 7:06 ` Tejun Heo
2008-10-15 7:19 ` Damazy
2008-10-15 7:25 ` Tejun Heo
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=48F58FBE.909@gmail.com \
--to=damazy@gmail.com \
--cc=jgarzik@pobox.com \
--cc=linux-ide@vger.kernel.org \
--cc=tj@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.