Re: 2.6.28-rc2 hates my e1000e

[Robert Hancock <hancockr@shaw.ca>]

Jonathan Corbet wrote:
> I tried booting -rc2 on my desktop system today.  All seems well until
> I try to access the net; eth0 doesn't exist anymore.  dmesg tells me:
> 
> Oct 30 17:29:38 bike kernel: e1000e: Intel(R) PRO/1000 Network Driver - 0.3.3.3-k6
> Oct 30 17:29:38 bike kernel: e1000e: Copyright (c) 1999-2008 Intel Corporation.
> Oct 30 17:29:38 bike kernel: e1000e 0000:00:19.0: PCI INT A -> GSI 21 (level, low) -> IRQ 21
> Oct 30 17:29:38 bike kernel: e1000e 0000:00:19.0: BAR 0: can't reserve mem region [0xfe9e0000-0xfe9fffff]
> Oct 30 17:29:38 bike kernel: e1000e 0000:00:19.0: PCI INT A disabled
> Oct 30 17:29:38 bike kernel: e1000e: probe of 0000:00:19.0 failed with error -16
> 
> Here's what lspci thinks of my device:
> 
> 00:19.0 Ethernet controller: Intel Corporation 82566DM-2 Gigabit Network Connection (rev 02)
> 	Subsystem: Dell OptiPlex 755
> 	Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
> 	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> 	Interrupt: pin A routed to IRQ 21
> 	Region 0: Memory at fe9e0000 (32-bit, non-prefetchable) [size=128K]
> 	Region 1: Memory at fe9db000 (32-bit, non-prefetchable) [size=4K]
> 	Region 2: I/O ports at ecc0 [size=32]
> 	Capabilities: [c8] Power Management version 2
> 		Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
> 		Status: D0 PME-Enable- DSel=0 DScale=1 PME-
> 	Capabilities: [d0] Message Signalled Interrupts: Mask- 64bit+ Count=1/1 Enable-
> 		Address: 0000000000000000  Data: 0000
> 	Capabilities: [e0] PCIe advanced features <?>
> 	Kernel modules: e1000e
> 
> Interestingly, under 2.6.27 it reads thus:
> 
> 00:19.0 Ethernet controller: Intel Corporation 82566DM-2 Gigabit Network Connection (rev 02)
> 	Subsystem: Dell OptiPlex 755
> 	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
> 	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> 	Latency: 0
> 	Interrupt: pin A routed to IRQ 4350
> 	Region 0: Memory at d4200000 (32-bit, non-prefetchable) [size=128K]
> 	Region 1: Memory at d4225000 (32-bit, non-prefetchable) [size=4K]
> 	Region 2: I/O ports at ecc0 [size=32]
> 	Capabilities: [c8] Power Management version 2
> 		Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
> 		Status: D0 PME-Enable- DSel=0 DScale=1 PME-
> 	Capabilities: [d0] Message Signalled Interrupts: Mask- 64bit+ Count=1/1 Enable+
> 		Address: 00000000fee0200c  Data: 4181
> 	Capabilities: [e0] PCIe advanced features <?>
> 	Kernel driver in use: e1000e
> 
> The I/O memory has moved, I have no idea why.  I assume that's a feature?
> 
> So...what else can I do to help track this one down?

What's in /proc/iomem? Full dmesg output from boot would also be useful.