From: Alexander Clausen <alex@gc-web.de>
To: Mikael Pettersson <mikpe@it.uu.se>
Cc: linux-ide@vger.kernel.org
Subject: Re: Suspend w/ sata_promise
Date: Sat, 22 Nov 2008 19:59:40 +0100 [thread overview]
Message-ID: <4928569C.9080805@gc-web.de> (raw)
In-Reply-To: <18728.13696.418178.143954@harpo.it.uu.se>
[-- Attachment #1: Type: text/plain, Size: 949 bytes --]
Mikael Pettersson wrote:
> >
> > Based on several other libata sata drivers I think handling suspend in
> > sata_promise may be as simple as hooking ata_pci_device_{suspend,resume},
> > which is what the patch below does. If this doesn't work then the most
> > likely solution is to augment the ->resume op with a Promise-specific
> > controller reset (again similar to several other sata drivers).
> >
> > Care to give it a try? The patch is against 2.6.28-rc5 but should also
> > work in 2.6.27.
>
> Alexander, have you had a chance to test this? Preferably together
> with Tejun's hardreset improvement patch posted recently.
> <http://marc.info/?l=linux-ide&m=122724338905689&w=2>
>
> With both this and Tejun's hardreset patch applied my Promise test
> machine survives several suspend/resume cycles without problems.
Did not work here. I applied both patches to 2.6.27.6, seems to behave exactly as before.
dmesg attached.
Alex
[-- Attachment #2: gu-dmesg-with-patch --]
[-- Type: text/plain, Size: 30986 bytes --]
nds
[ 251.267347] EXT3 FS on sdb1, internal journal
[ 251.267432] EXT3-fs: mounted filesystem with ordered data mode.
[ 284.935327] PM: Syncing filesystems ... done.
[ 284.942293] PM: Preparing system for mem sleep
[ 284.943220] Freezing user space processes ... (elapsed 0.00 seconds) done.
[ 284.943612] Freezing remaining freezable tasks ... (elapsed 0.00 seconds) done.
[ 284.943776] PM: Entering mem sleep
[ 284.943793] agpgart-amd64 0000:00:00.0: preparing suspend
[ 284.943795] pci 0000:00:01.0: preparing suspend
[ 284.943797] sata_via 0000:00:08.0: preparing suspend
[ 284.943799] r8169 0000:00:0b.0: preparing suspend
[ 284.943801] sata_promise 0000:00:0d.0: preparing suspend
[ 284.943803] pci 0000:00:0e.0: preparing suspend
[ 284.943805] sata_via 0000:00:0f.0: preparing suspend
[ 284.943807] VIA_IDE 0000:00:0f.1: preparing suspend
[ 284.943809] uhci_hcd 0000:00:10.0: preparing suspend
[ 284.943811] uhci_hcd 0000:00:10.1: preparing suspend
[ 284.943813] uhci_hcd 0000:00:10.2: preparing suspend
[ 284.943815] uhci_hcd 0000:00:10.3: preparing suspend
[ 284.943817] ehci_hcd 0000:00:10.4: preparing suspend
[ 284.943819] pci 0000:00:11.0: preparing suspend
[ 284.943821] VIA 82xx Audio 0000:00:11.5: preparing suspend
[ 284.943823] pci 0000:00:18.0: preparing suspend
[ 284.943825] pci 0000:00:18.1: preparing suspend
[ 284.943827] pci 0000:00:18.2: preparing suspend
[ 284.943829] k8temp 0000:00:18.3: preparing suspend
[ 284.943831] nvidia 0000:01:00.0: preparing suspend
[ 284.943839] pcspkr pcspkr: preparing suspend
[ 284.943842] platform vesafb.0: preparing suspend
[ 284.943860] serial8250 serial8250: preparing suspend
[ 284.943881] usb usb1: preparing type suspend, may wakeup
[ 284.943885] usb usb2: preparing type suspend, may wakeup
[ 284.943888] usb usb3: preparing type suspend, may wakeup
[ 284.943891] usb usb4: preparing type suspend, may wakeup
[ 284.943894] usb usb5: preparing type suspend, may wakeup
[ 284.943896] usb 3-2: preparing type suspend, may wakeup
[ 284.943900] i8042 i8042: preparing suspend
[ 284.943907] platform floppy.0: preparing suspend
[ 284.943918] usb 1-2: preparing type suspend
[ 284.943924] sd 8:0:0:0: legacy suspend
[ 284.943929] usb 1-2: type suspend
[ 284.956032] rtc rtc0: legacy class suspend
[ 284.956061] platform floppy.0: suspend
[ 284.956064] ac97 0-0:ALC655: legacy suspend
[ 284.956067] psmouse serio1: legacy suspend
[ 285.419357] atkbd serio0: legacy suspend
[ 285.964022] i8042 i8042: suspend
[ 285.964032] usb 3-2: type suspend, may wakeup
[ 285.980027] usb usb5: type suspend, may wakeup
[ 285.980030] usb usb4: type suspend, may wakeup
[ 285.980032] usb usb3: type suspend, may wakeup
[ 285.980046] usb usb2: type suspend, may wakeup
[ 285.980048] usb usb1: type suspend, may wakeup
[ 285.980067] sd 1:0:0:0: legacy suspend
[ 285.980070] sd 1:0:0:0: [sda] Synchronizing SCSI cache
[ 285.980284] sd 1:0:0:0: [sda] Stopping disk
[ 286.292755] serial8250 serial8250: suspend
[ 286.292767] platform vesafb.0: suspend
[ 286.292769] pcspkr pcspkr: suspend
[ 286.292777] i8042 kbd 00:0a: legacy suspend
[ 286.292795] i8042 aux 00:09: legacy suspend
[ 286.292799] pnp 00:08: legacy suspend
[ 286.292801] pnp 00:07: legacy suspend
[ 286.292803] rtc_cmos 00:06: legacy suspend, may wakeup
[ 286.292810] pnp 00:05: legacy suspend
[ 286.292812] system 00:04: legacy suspend
[ 286.292816] pnp 00:03: legacy suspend
[ 286.292818] serial 00:02: legacy suspend
[ 286.292972] serial 00:02: disabled
[ 286.293038] pnp 00:01: legacy suspend
[ 286.293040] pnp 00:00: legacy suspend
[ 286.293042] nvidia 0000:01:00.0: suspend
[ 286.293046] ACPI handle has no context!
[ 286.293057] NVRM: RmPowerManagement: 4
[ 286.368257] k8temp 0000:00:18.3: suspend
[ 286.368265] pci 0000:00:18.2: suspend
[ 286.368270] pci 0000:00:18.1: suspend
[ 286.368275] pci 0000:00:18.0: suspend
[ 286.368281] VIA 82xx Audio 0000:00:11.5: suspend
[ 286.369014] VIA 82xx Audio 0000:00:11.5: PCI INT C disabled
[ 286.384028] pci 0000:00:11.0: suspend
[ 286.384051] ehci_hcd 0000:00:10.4: suspend
[ 286.384079] ehci_hcd 0000:00:10.4: PCI INT C disabled
[ 286.400024] uhci_hcd 0000:00:10.3: suspend
[ 286.400052] uhci_hcd 0000:00:10.3: PCI INT B disabled
[ 286.416023] uhci_hcd 0000:00:10.2: suspend
[ 286.416050] uhci_hcd 0000:00:10.2: PCI INT B disabled
[ 286.432023] uhci_hcd 0000:00:10.1: suspend
[ 286.432051] uhci_hcd 0000:00:10.1: PCI INT A disabled
[ 286.448022] uhci_hcd 0000:00:10.0: suspend
[ 286.448050] uhci_hcd 0000:00:10.0: PCI INT A disabled
[ 286.464023] VIA_IDE 0000:00:0f.1: suspend
[ 286.464047] sata_via 0000:00:0f.0: suspend
[ 286.824051] sata_via 0000:00:0f.0: PCI INT B disabled
[ 286.840027] pci 0000:00:0e.0: suspend
[ 286.840050] sata_promise 0000:00:0d.0: suspend
[ 286.840718] sata_promise 0000:00:0d.0: PCI INT A disabled
[ 286.856027] r8169 0000:00:0b.0: suspend
[ 286.856055] ACPI handle has no context!
[ 286.856059] ACPI handle has no context!
[ 286.872026] sata_via 0000:00:08.0: suspend
[ 286.872090] sata_via 0000:00:08.0: PCI INT A disabled
[ 286.888027] pci 0000:00:01.0: suspend
[ 286.888046] agpgart-amd64 0000:00:00.0: suspend
[ 286.888078] ACPI handle has no context!
[ 286.904027] acpi LNXTHERM:00: legacy suspend
[ 286.904029] button PNP0C0E:00: legacy suspend
[ 286.904031] pci_link PNP0C0F:07: legacy suspend
[ 286.904033] pci_link PNP0C0F:06: legacy suspend
[ 286.904035] pci_link PNP0C0F:05: legacy suspend
[ 286.904037] pci_link PNP0C0F:04: legacy suspend
[ 286.904039] pci_link PNP0C0F:03: legacy suspend
[ 286.904041] pci_link PNP0C0F:02: legacy suspend
[ 286.904043] pci_link PNP0C0F:01: legacy suspend
[ 286.904045] pci_link PNP0C0F:00: legacy suspend
[ 286.904046] acpi device:13: legacy suspend
[ 286.904048] acpi device:12: legacy suspend
[ 286.904050] acpi device:11: legacy suspend
[ 286.904052] acpi device:10: legacy suspend
[ 286.904054] acpi device:0f: legacy suspend
[ 286.904056] acpi device:0e: legacy suspend
[ 286.904057] acpi device:0d: legacy suspend
[ 286.904059] acpi device:0c: legacy suspend
[ 286.904061] acpi device:0b: legacy suspend
[ 286.904063] acpi device:0a: legacy suspend
[ 286.904065] acpi device:09: legacy suspend
[ 286.904066] acpi device:08: legacy suspend
[ 286.904068] acpi PNP0303:00: legacy suspend
[ 286.904070] acpi PNP0F13:00: legacy suspend
[ 286.904072] acpi PNP0C04:00: legacy suspend
[ 286.904074] acpi PNP0800:00: legacy suspend
[ 286.904076] acpi PNP0B00:00: legacy suspend
[ 286.904077] acpi PNP0100:00: legacy suspend
[ 286.904079] acpi PNP0200:00: legacy suspend
[ 286.904081] acpi PNP0C02:00: legacy suspend
[ 286.904083] acpi device:07: legacy suspend
[ 286.904085] acpi device:06: legacy suspend
[ 286.904087] acpi device:05: legacy suspend
[ 286.904089] acpi device:04: legacy suspend
[ 286.904090] acpi device:03: legacy suspend
[ 286.904092] acpi device:02: legacy suspend
[ 286.904094] acpi device:01: legacy suspend
[ 286.904096] power LNXPOWER:03: legacy suspend
[ 286.904098] power LNXPOWER:02: legacy suspend
[ 286.904100] power LNXPOWER:01: legacy suspend
[ 286.904102] power LNXPOWER:00: legacy suspend
[ 286.904104] acpi PNP0401:00: legacy suspend
[ 286.904106] acpi PNP0501:00: legacy suspend
[ 286.904107] acpi PNP0700:00: legacy suspend
[ 286.904109] pci_root PNP0A03:00: legacy suspend
[ 286.904111] button PNP0C0C:00: legacy suspend
[ 286.904113] acpi device:00: legacy suspend
[ 286.904115] processor ACPI0007:00: legacy suspend
[ 286.904118] button LNXPWRBN:00: legacy suspend
[ 286.904120] acpi LNXSYSTM:00: legacy suspend
[ 286.904333] ACPI: Preparing to enter system sleep state S3
[ 286.904729] platform floppy.0: LATE suspend
[ 286.904733] i8042 i8042: LATE suspend
[ 286.904745] serial8250 serial8250: LATE suspend
[ 286.904753] platform vesafb.0: LATE suspend
[ 286.904755] pcspkr pcspkr: LATE suspend
[ 286.904759] nvidia 0000:01:00.0: LATE suspend
[ 286.904762] k8temp 0000:00:18.3: LATE suspend
[ 286.904764] pci 0000:00:18.2: LATE suspend
[ 286.904765] pci 0000:00:18.1: LATE suspend
[ 286.904767] pci 0000:00:18.0: LATE suspend
[ 286.904769] VIA 82xx Audio 0000:00:11.5: LATE suspend
[ 286.904771] pci 0000:00:11.0: LATE suspend
[ 286.904773] ehci_hcd 0000:00:10.4: LATE suspend
[ 286.904775] uhci_hcd 0000:00:10.3: LATE suspend
[ 286.904776] uhci_hcd 0000:00:10.2: LATE suspend
[ 286.904778] uhci_hcd 0000:00:10.1: LATE suspend
[ 286.904780] uhci_hcd 0000:00:10.0: LATE suspend
[ 286.904782] VIA_IDE 0000:00:0f.1: LATE suspend
[ 286.904784] sata_via 0000:00:0f.0: LATE suspend
[ 286.904785] pci 0000:00:0e.0: LATE suspend
[ 286.904787] sata_promise 0000:00:0d.0: LATE suspend
[ 286.904789] r8169 0000:00:0b.0: LATE suspend
[ 286.904791] sata_via 0000:00:08.0: LATE suspend
[ 286.904793] pci 0000:00:01.0: LATE suspend
[ 286.904795] agpgart-amd64 0000:00:00.0: LATE suspend
[ 286.908011] hwsleep-0311 [00] enter_sleep_state : Entering sleep state [S3]
[ 286.908011] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[ 286.908011] Intel machine check architecture supported.
[ 286.908011] Intel machine check reporting enabled on CPU#0.
[ 286.908011] evxfevnt-0079 [00] enable : System is already in ACPI mode
[ 286.908011] Back to C!
[ 286.908011] agpgart-amd64 0000:00:00.0: EARLY resume
[ 286.908011] pci 0000:00:01.0: EARLY resume
[ 286.908011] sata_via 0000:00:08.0: EARLY resume
[ 286.908011] r8169 0000:00:0b.0: EARLY resume
[ 286.908011] sata_promise 0000:00:0d.0: EARLY resume
[ 286.908011] pci 0000:00:0e.0: EARLY resume
[ 286.908011] sata_via 0000:00:0f.0: EARLY resume
[ 286.908011] VIA_IDE 0000:00:0f.1: EARLY resume
[ 286.908011] uhci_hcd 0000:00:10.0: EARLY resume
[ 286.908011] uhci_hcd 0000:00:10.1: EARLY resume
[ 286.908011] uhci_hcd 0000:00:10.2: EARLY resume
[ 286.908011] uhci_hcd 0000:00:10.3: EARLY resume
[ 286.908011] ehci_hcd 0000:00:10.4: EARLY resume
[ 286.908011] pci 0000:00:11.0: EARLY resume
[ 286.908011] VIA 82xx Audio 0000:00:11.5: EARLY resume
[ 286.908011] pci 0000:00:18.0: EARLY resume
[ 286.908011] pci 0000:00:18.1: EARLY resume
[ 286.908011] pci 0000:00:18.2: EARLY resume
[ 286.908011] k8temp 0000:00:18.3: EARLY resume
[ 286.908011] nvidia 0000:01:00.0: EARLY resume
[ 286.908011] pcspkr pcspkr: EARLY resume
[ 286.908011] platform vesafb.0: EARLY resume
[ 286.908011] serial8250 serial8250: EARLY resume
[ 286.908011] i8042 i8042: EARLY resume
[ 286.908011] platform floppy.0: EARLY resume
[ 286.908011] ACPI: Waking up from system sleep state S3
[ 287.564153] acpi LNXSYSTM:00: legacy resume
[ 287.564155] button LNXPWRBN:00: legacy resume
[ 287.564157] processor ACPI0007:00: legacy resume
[ 287.564160] acpi device:00: legacy resume
[ 287.564161] button PNP0C0C:00: legacy resume
[ 287.564163] pci_root PNP0A03:00: legacy resume
[ 287.564165] acpi PNP0700:00: legacy resume
[ 287.564167] acpi PNP0501:00: legacy resume
[ 287.564169] acpi PNP0401:00: legacy resume
[ 287.564171] power LNXPOWER:00: legacy resume
[ 287.564196] power LNXPOWER:01: legacy resume
[ 287.564220] power LNXPOWER:02: legacy resume
[ 287.564243] power LNXPOWER:03: legacy resume
[ 287.564267] acpi device:01: legacy resume
[ 287.564268] acpi device:02: legacy resume
[ 287.564270] acpi device:03: legacy resume
[ 287.564272] acpi device:04: legacy resume
[ 287.564274] acpi device:05: legacy resume
[ 287.564276] acpi device:06: legacy resume
[ 287.564278] acpi device:07: legacy resume
[ 287.564279] acpi PNP0C02:00: legacy resume
[ 287.564281] acpi PNP0200:00: legacy resume
[ 287.564283] acpi PNP0100:00: legacy resume
[ 287.564285] acpi PNP0B00:00: legacy resume
[ 287.564286] acpi PNP0800:00: legacy resume
[ 287.564288] acpi PNP0C04:00: legacy resume
[ 287.564290] acpi PNP0F13:00: legacy resume
[ 287.564292] acpi PNP0303:00: legacy resume
[ 287.564294] acpi device:08: legacy resume
[ 287.564295] acpi device:09: legacy resume
[ 287.564297] acpi device:0a: legacy resume
[ 287.564299] acpi device:0b: legacy resume
[ 287.564301] acpi device:0c: legacy resume
[ 287.564303] acpi device:0d: legacy resume
[ 287.564304] acpi device:0e: legacy resume
[ 287.564306] acpi device:0f: legacy resume
[ 287.564308] acpi device:10: legacy resume
[ 287.564310] acpi device:11: legacy resume
[ 287.564311] acpi device:12: legacy resume
[ 287.564313] acpi device:13: legacy resume
[ 287.564315] pci_link PNP0C0F:00: legacy resume
[ 287.564317] pci_link PNP0C0F:01: legacy resume
[ 287.564319] pci_link PNP0C0F:02: legacy resume
[ 287.564321] pci_link PNP0C0F:03: legacy resume
[ 287.564323] pci_link PNP0C0F:04: legacy resume
[ 287.564325] pci_link PNP0C0F:05: legacy resume
[ 287.564326] pci_link PNP0C0F:06: legacy resume
[ 287.564328] pci_link PNP0C0F:07: legacy resume
[ 287.564330] button PNP0C0E:00: legacy resume
[ 287.564332] acpi LNXTHERM:00: legacy resume
[ 287.564334] agpgart-amd64 0000:00:00.0: resume
[ 287.580056] pci 0000:00:01.0: resume
[ 287.580080] pci 0000:00:01.0: setting latency timer to 64
[ 287.580083] sata_via 0000:00:08.0: resume
[ 287.596053] sata_via 0000:00:08.0: PCI INT A -> Link[LNKD] -> GSI 10 (level, low) -> IRQ 10
[ 287.596244] r8169 0000:00:0b.0: resume
[ 287.612042] r8169 0000:00:0b.0: restoring config space at offset 0x3 (was 0x2008, writing 0x4008)
[ 287.612057] sata_promise 0000:00:0d.0: resume
[ 287.628039] r8169: eth1: link up
[ 287.628128] sata_promise 0000:00:0d.0: PCI INT A -> Link[LNKB] -> GSI 5 (level, low) -> IRQ 5
[ 287.628594] pci 0000:00:0e.0: resume
[ 287.628617] sata_via 0000:00:0f.0: resume
[ 287.644051] sata_via 0000:00:0f.0: PCI INT B -> Link[LNKB] -> GSI 5 (level, low) -> IRQ 5
[ 287.644119] VIA_IDE 0000:00:0f.1: resume
[ 287.644125] VIA_IDE 0000:00:0f.1: restoring config space at offset 0xf (was 0x1ff, writing 0x10b)
[ 287.644150] VIA_IDE 0000:00:0f.1: PCI INT A -> Link[LNKA] -> GSI 11 (level, low) -> IRQ 11
[ 287.644211] uhci_hcd 0000:00:10.0: resume
[ 287.660028] uhci_hcd 0000:00:10.0: PCI INT A -> Link[LNKA] -> GSI 11 (level, low) -> IRQ 11
[ 287.660126] usb usb2: root hub lost power or was reset
[ 287.660182] uhci_hcd 0000:00:10.1: resume
[ 287.676028] uhci_hcd 0000:00:10.1: PCI INT A -> Link[LNKA] -> GSI 11 (level, low) -> IRQ 11
[ 287.676128] usb usb3: root hub lost power or was reset
[ 287.676183] uhci_hcd 0000:00:10.2: resume
[ 287.692028] uhci_hcd 0000:00:10.2: PCI INT B -> Link[LNKB] -> GSI 5 (level, low) -> IRQ 5
[ 287.692122] usb usb4: root hub lost power or was reset
[ 287.692178] uhci_hcd 0000:00:10.3: resume
[ 287.708028] uhci_hcd 0000:00:10.3: PCI INT B -> Link[LNKB] -> GSI 5 (level, low) -> IRQ 5
[ 287.708124] usb usb5: root hub lost power or was reset
[ 287.708180] ehci_hcd 0000:00:10.4: resume
[ 287.724028] ehci_hcd 0000:00:10.4: PCI INT C -> Link[LNKC] -> GSI 3 (level, low) -> IRQ 3
[ 287.724105] ehci_hcd 0000:00:10.4: restoring config space at offset 0x3 (was 0x802008, writing 0x802010)
[ 287.724116] pci 0000:00:11.0: resume
[ 287.724141] VIA 82xx Audio 0000:00:11.5: resume
[ 287.740050] VIA 82xx Audio 0000:00:11.5: PCI INT C -> Link[LNKC] -> GSI 3 (level, low) -> IRQ 3
[ 287.740119] VIA 82xx Audio 0000:00:11.5: setting latency timer to 64
[ 287.743062] pci 0000:00:18.0: resume
[ 287.743069] pci 0000:00:18.1: resume
[ 287.743074] pci 0000:00:18.2: resume
[ 287.743080] k8temp 0000:00:18.3: resume
[ 287.743085] nvidia 0000:01:00.0: resume
[ 287.743100] NVRM: RmPowerManagement: 5
[ 287.937261] ata5: SATA link down (SStatus 0 SControl 310)
[ 287.937332] ata4: SATA link down (SStatus 0 SControl 310)
[ 287.948092] ata1: SATA link down (SStatus 0 SControl 300)
[ 288.104053] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 288.120510] ata2.00: configured for UDMA/133
[ 288.120798] sd 1:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB)
[ 288.120858] sd 1:0:0:0: [sda] Write Protect is off
[ 288.120906] sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 288.120922] sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 288.623918] pnp 00:00: legacy resume
[ 288.623923] pnp 00:01: legacy resume
[ 288.623925] serial 00:02: legacy resume
[ 288.624705] serial 00:02: activated
[ 288.624756] pnp 00:03: legacy resume
[ 288.624758] system 00:04: legacy resume
[ 288.624760] pnp 00:05: legacy resume
[ 288.624762] rtc_cmos 00:06: legacy resume
[ 288.624765] pnp 00:07: legacy resume
[ 288.624766] pnp 00:08: legacy resume
[ 288.624768] i8042 aux 00:09: legacy resume
[ 288.624771] i8042 kbd 00:0a: legacy resume
[ 288.624775] pcspkr pcspkr: resume
[ 288.624778] platform vesafb.0: resume
[ 288.624793] serial8250 serial8250: resume
[ 288.624809] sd 1:0:0:0: legacy resume
[ 288.624812] sd 1:0:0:0: [sda] Starting disk
[ 288.630209] usb usb1: type resume
[ 288.696044] usb usb2: type resume
[ 288.696047] usb usb3: type resume
[ 288.944027] usb usb4: type resume
[ 288.944030] usb usb5: type resume
[ 288.944032] usb 3-2: type resume
[ 289.056029] usb 3-2: reset full speed USB device using uhci_hcd and address 2
[ 289.202941] i8042 i8042: resume
[ 289.202966] atkbd serio0: legacy resume
[ 289.202969] psmouse serio1: legacy resume
[ 289.202973] ac97 0-0:ALC655: legacy resume
[ 289.202977] platform floppy.0: resume
[ 289.202982] rtc rtc0: legacy class resume
[ 289.203020] usb 1-2: type resume
[ 289.248174] sd 8:0:0:0: legacy resume
[ 289.248180] usb 1-2: completing type resume
[ 289.248185] platform floppy.0: completing resume
[ 289.248188] i8042 i8042: completing resume
[ 289.248191] usb 3-2: completing type resume
[ 289.248193] usb usb5: completing type resume
[ 289.248195] usb usb4: completing type resume
[ 289.248197] usb usb3: completing type resume
[ 289.248199] usb usb2: completing type resume
[ 289.248201] usb usb1: completing type resume
[ 289.248212] serial8250 serial8250: completing resume
[ 289.248220] platform vesafb.0: completing resume
[ 289.248222] pcspkr pcspkr: completing resume
[ 289.248227] nvidia 0000:01:00.0: completing resume
[ 289.248229] k8temp 0000:00:18.3: completing resume
[ 289.248231] pci 0000:00:18.2: completing resume
[ 289.248233] pci 0000:00:18.1: completing resume
[ 289.248234] pci 0000:00:18.0: completing resume
[ 289.248237] VIA 82xx Audio 0000:00:11.5: completing resume
[ 289.248239] pci 0000:00:11.0: completing resume
[ 289.248241] ehci_hcd 0000:00:10.4: completing resume
[ 289.248242] uhci_hcd 0000:00:10.3: completing resume
[ 289.248244] uhci_hcd 0000:00:10.2: completing resume
[ 289.248246] uhci_hcd 0000:00:10.1: completing resume
[ 289.248248] uhci_hcd 0000:00:10.0: completing resume
[ 289.248250] VIA_IDE 0000:00:0f.1: completing resume
[ 289.248252] sata_via 0000:00:0f.0: completing resume
[ 289.248254] pci 0000:00:0e.0: completing resume
[ 289.248256] sata_promise 0000:00:0d.0: completing resume
[ 289.248258] r8169 0000:00:0b.0: completing resume
[ 289.248260] sata_via 0000:00:08.0: completing resume
[ 289.248262] pci 0000:00:01.0: completing resume
[ 289.248264] agpgart-amd64 0000:00:00.0: completing resume
[ 289.248277] PM: Finishing wakeup.
[ 289.248278] Restarting tasks ... done.
[ 325.641151] PM: Syncing filesystems ... done.
[ 325.659966] PM: Preparing system for mem sleep
[ 325.660883] Freezing user space processes ... (elapsed 0.00 seconds) done.
[ 325.661281] Freezing remaining freezable tasks ... (elapsed 0.00 seconds) done.
[ 325.661461] PM: Entering mem sleep
[ 325.661479] agpgart-amd64 0000:00:00.0: preparing suspend
[ 325.661481] pci 0000:00:01.0: preparing suspend
[ 325.661483] sata_via 0000:00:08.0: preparing suspend
[ 325.661485] r8169 0000:00:0b.0: preparing suspend
[ 325.661487] sata_promise 0000:00:0d.0: preparing suspend
[ 325.661489] pci 0000:00:0e.0: preparing suspend
[ 325.661491] sata_via 0000:00:0f.0: preparing suspend
[ 325.661493] VIA_IDE 0000:00:0f.1: preparing suspend
[ 325.661495] uhci_hcd 0000:00:10.0: preparing suspend
[ 325.661497] uhci_hcd 0000:00:10.1: preparing suspend
[ 325.661499] uhci_hcd 0000:00:10.2: preparing suspend
[ 325.661501] uhci_hcd 0000:00:10.3: preparing suspend
[ 325.661503] ehci_hcd 0000:00:10.4: preparing suspend
[ 325.661505] pci 0000:00:11.0: preparing suspend
[ 325.661507] VIA 82xx Audio 0000:00:11.5: preparing suspend
[ 325.661509] pci 0000:00:18.0: preparing suspend
[ 325.661511] pci 0000:00:18.1: preparing suspend
[ 325.661513] pci 0000:00:18.2: preparing suspend
[ 325.661515] k8temp 0000:00:18.3: preparing suspend
[ 325.661517] nvidia 0000:01:00.0: preparing suspend
[ 325.661525] pcspkr pcspkr: preparing suspend
[ 325.661528] platform vesafb.0: preparing suspend
[ 325.661545] serial8250 serial8250: preparing suspend
[ 325.661566] usb usb1: preparing type suspend, may wakeup
[ 325.661570] usb usb2: preparing type suspend, may wakeup
[ 325.661573] usb usb3: preparing type suspend, may wakeup
[ 325.661576] usb usb4: preparing type suspend, may wakeup
[ 325.661579] usb usb5: preparing type suspend, may wakeup
[ 325.661581] usb 3-2: preparing type suspend, may wakeup
[ 325.661585] i8042 i8042: preparing suspend
[ 325.661592] platform floppy.0: preparing suspend
[ 325.661602] usb 1-2: preparing type suspend
[ 325.661608] sd 8:0:0:0: legacy suspend
[ 325.661614] usb 1-2: type suspend
[ 325.676032] rtc rtc0: legacy class suspend
[ 325.676061] platform floppy.0: suspend
[ 325.676064] ac97 0-0:ALC655: legacy suspend
[ 325.676067] psmouse serio1: legacy suspend
[ 326.139718] atkbd serio0: legacy suspend
[ 326.684026] i8042 i8042: suspend
[ 326.684036] usb 3-2: type suspend, may wakeup
[ 326.700028] usb usb5: type suspend, may wakeup
[ 326.700030] usb usb4: type suspend, may wakeup
[ 326.700033] usb usb3: type suspend, may wakeup
[ 326.700047] usb usb2: type suspend, may wakeup
[ 326.700049] usb usb1: type suspend, may wakeup
[ 326.700068] sd 1:0:0:0: legacy suspend
[ 326.700070] sd 1:0:0:0: [sda] Synchronizing SCSI cache
[ 326.700270] sd 1:0:0:0: [sda] Stopping disk
[ 356.700042] ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 356.700097] ata2.00: cmd e0/00:00:00:00:00/00:00:00:00:00/a0 tag 0
[ 356.700098] res 40/00:fe:00:00:00/00:00:00:00:00/40 Emask 0x4 (timeout)
[ 356.700204] ata2.00: status: { DRDY }
[ 356.700259] ata2: hard resetting link
[ 357.020040] ata2: SATA link down (SStatus 100 SControl 300)
[ 357.201056] ata2: hard resetting link
[ 357.676057] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 357.692923] ata2.00: both IDENTIFYs aborted, assuming NODEV
[ 357.692925] ata2.00: revalidation failed (errno=-2)
[ 362.676030] ata2: hard resetting link
[ 363.152055] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 363.168527] ata2.00: configured for UDMA/133
[ 363.168781] ata2: exception Emask 0x10 SAct 0x0 SErr 0x0 action 0x9 t4
[ 363.168832] ata2: hotplug_status 0x2
[ 363.184526] ata2.00: configured for UDMA/133
[ 363.184576] ata2: EH complete
[ 393.184032] ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 393.184085] ata2.00: cmd e0/00:00:00:00:00/00:00:00:00:00/a0 tag 0
[ 393.184086] res 40/00:fe:00:00:00/00:00:00:00:00/40 Emask 0x4 (timeout)
[ 393.184195] ata2.00: status: { DRDY }
[ 393.184247] ata2: hard resetting link
[ 393.504040] ata2: SATA link down (SStatus 100 SControl 300)
[ 393.685041] ata2: hard resetting link
[ 394.160056] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 394.176527] ata2.00: configured for UDMA/133
[ 394.176780] ata2: limiting SATA link speed to 1.5 Gbps
[ 394.176829] ata2: exception Emask 0x10 SAct 0x0 SErr 0x0 action 0xf t4
[ 394.176880] ata2: hotplug_status 0x2
[ 394.176932] ata2: hard resetting link
[ 395.056056] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 395.072921] ata2.00: both IDENTIFYs aborted, assuming NODEV
[ 395.072924] ata2.00: revalidation failed (errno=-2)
[ 400.056032] ata2: hard resetting link
[ 400.532056] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 400.548527] ata2.00: configured for UDMA/133
[ 400.548576] ata2: EH complete
[ 430.548035] ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 430.548088] ata2.00: cmd e0/00:00:00:00:00/00:00:00:00:00/a0 tag 0
[ 430.548089] res 40/00:fe:00:00:00/00:00:00:00:00/40 Emask 0x4 (timeout)
[ 430.548199] ata2.00: status: { DRDY }
[ 430.548250] ata2: hard resetting link
[ 430.868039] ata2: SATA link down (SStatus 100 SControl 300)
[ 431.049048] ata2: hard resetting link
[ 431.524055] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 431.540528] ata2.00: configured for UDMA/133
[ 431.540780] ata2: exception Emask 0x10 SAct 0x0 SErr 0x0 action 0x9 t4
[ 431.540830] ata2: hotplug_status 0x2
[ 431.556523] ata2.00: configured for UDMA/133
[ 431.556571] ata2: EH complete
[ 461.556034] ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 461.556087] ata2.00: cmd e0/00:00:00:00:00/00:00:00:00:00/a0 tag 0
[ 461.556088] res 40/00:fe:00:00:00/00:00:00:00:00/40 Emask 0x4 (timeout)
[ 461.556196] ata2.00: status: { DRDY }
[ 461.556251] ata2: hard resetting link
[ 461.876041] ata2: SATA link down (SStatus 100 SControl 300)
[ 462.057051] ata2: hard resetting link
[ 462.532056] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 462.548527] ata2.00: configured for UDMA/133
[ 462.548781] ata2.00: limiting speed to UDMA/100:PIO4
[ 462.548829] ata2: exception Emask 0x10 SAct 0x0 SErr 0x0 action 0xf t4
[ 462.548878] ata2: hotplug_status 0x2
[ 462.548930] ata2: hard resetting link
[ 463.428055] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 463.444524] ata2.00: configured for UDMA/100
[ 463.444573] ata2: EH complete
[ 493.444034] ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 493.444090] ata2.00: cmd e0/00:00:00:00:00/00:00:00:00:00/a0 tag 0
[ 493.444091] res 40/00:fe:00:00:00/00:00:00:00:00/40 Emask 0x4 (timeout)
[ 493.444201] ata2.00: status: { DRDY }
[ 493.444256] ata2: hard resetting link
[ 493.764040] ata2: SATA link down (SStatus 100 SControl 300)
[ 493.945059] ata2: hard resetting link
[ 494.420057] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 494.436525] ata2.00: configured for UDMA/100
[ 494.436780] ata2.00: limiting speed to UDMA/33:PIO4
[ 494.436830] ata2: exception Emask 0x10 SAct 0x0 SErr 0x0 action 0xf t4
[ 494.436880] ata2: hotplug_status 0x2
[ 494.436941] ata2: hard resetting link
[ 495.316055] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 495.332525] ata2.00: configured for UDMA/33
[ 495.332579] ata2: EH complete
[ 525.332034] ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 525.332087] ata2.00: cmd e0/00:00:00:00:00/00:00:00:00:00/a0 tag 0
[ 525.332088] res 40/00:fe:00:00:00/00:00:00:00:00/40 Emask 0x4 (timeout)
[ 525.332195] ata2.00: status: { DRDY }
[ 525.332246] ata2: hard resetting link
[ 525.652039] ata2: SATA link down (SStatus 100 SControl 300)
[ 525.833043] ata2: hard resetting link
[ 526.308055] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 526.324527] ata2.00: configured for UDMA/33
[ 526.324780] ata2: exception Emask 0x10 SAct 0x0 SErr 0x0 action 0x9 t4
[ 526.324830] ata2: hotplug_status 0x2
[ 526.340526] ata2.00: configured for UDMA/33
[ 526.340577] sd 1:0:0:0: [sda] START_STOP FAILED
[ 526.340625] sd 1:0:0:0: [sda] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE,SUGGEST_OK
[ 526.340720] sd 1:0:0:0: [sda] Sense Key : Aborted Command [current] [descriptor]
[ 526.340912] sd 1:0:0:0: [sda] Add. Sense: No additional sense information
[ 526.341031] suspend_device(): scsi_bus_suspend+0x0/0x3f returns 134217730
[ 526.341154] PM: Device 1:0:0:0 failed to suspend: error 134217730
[ 526.341203] PM: Some devices failed to suspend
[ 526.341280] usb usb1: type resume
[ 526.369089] ata2: EH complete
[ 526.369164] sd 1:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB)
[ 526.369226] sd 1:0:0:0: [sda] Write Protect is off
[ 526.369275] sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 526.369291] sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 526.369369] sd 1:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB)
[ 526.369427] sd 1:0:0:0: [sda] Write Protect is off
[ 526.369476] sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 526.369491] sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 526.408037] usb usb2: type resume
[ 526.408040] usb usb3: type resume
[ 526.448029] usb usb4: type resume
[ 526.448032] usb usb5: type resume
[ 526.448033] usb 3-2: type resume
[ 526.499029] i8042 i8042: resume
[ 526.499053] atkbd serio0: legacy resume
[ 526.499056] psmouse serio1: legacy resume
[ 526.499060] ac97 0-0:ALC655: legacy resume
[ 526.499063] platform floppy.0: resume
[ 526.499067] rtc rtc0: legacy class resume
[ 526.499106] usb 1-2: type resume
[ 526.544154] sd 8:0:0:0: legacy resume
[ 526.544160] usb 1-2: completing type resume
[ 526.544165] platform floppy.0: completing resume
[ 526.544168] i8042 i8042: completing resume
[ 526.544171] usb 3-2: completing type resume
[ 526.544173] usb usb5: completing type resume
[ 526.544175] usb usb4: completing type resume
[ 526.544177] usb usb3: completing type resume
[ 526.544180] usb usb2: completing type resume
[ 526.544182] usb usb1: completing type resume
[ 526.544194] serial8250 serial8250: completing resume
[ 526.544206] platform vesafb.0: completing resume
[ 526.544208] pcspkr pcspkr: completing resume
[ 526.544214] nvidia 0000:01:00.0: completing resume
[ 526.544216] k8temp 0000:00:18.3: completing resume
[ 526.544218] pci 0000:00:18.2: completing resume
[ 526.544220] pci 0000:00:18.1: completing resume
[ 526.544221] pci 0000:00:18.0: completing resume
[ 526.544223] VIA 82xx Audio 0000:00:11.5: completing resume
[ 526.544225] pci 0000:00:11.0: completing resume
[ 526.544227] ehci_hcd 0000:00:10.4: completing resume
[ 526.544229] uhci_hcd 0000:00:10.3: completing resume
[ 526.544231] uhci_hcd 0000:00:10.2: completing resume
[ 526.544233] uhci_hcd 0000:00:10.1: completing resume
[ 526.544234] uhci_hcd 0000:00:10.0: completing resume
[ 526.544236] VIA_IDE 0000:00:0f.1: completing resume
[ 526.544238] sata_via 0000:00:0f.0: completing resume
[ 526.544240] pci 0000:00:0e.0: completing resume
[ 526.544242] sata_promise 0000:00:0d.0: completing resume
[ 526.544244] r8169 0000:00:0b.0: completing resume
[ 526.544246] sata_via 0000:00:08.0: completing resume
[ 526.544248] pci 0000:00:01.0: completing resume
[ 526.544250] agpgart-amd64 0000:00:00.0: completing resume
[ 526.544259] PM: Finishing wakeup.
[ 526.544261] Restarting tasks ... done.
[ 526.628454] PM: Removing info for No Bus:mouse0
[ 526.640035] PM: Removing info for No Bus:event1
[ 526.652039] PM: Removing info for No Bus:input1
next prev parent reply other threads:[~2008-11-22 18:59 UTC|newest]
Thread overview: 15+ messages / expand[flat|nested] mbox.gz Atom feed top
2008-11-16 14:22 Suspend w/ sata_promise Alexander Clausen
2008-11-16 14:24 ` Alexander Clausen
2008-11-16 16:22 ` Mikael Pettersson
2008-11-16 16:43 ` Alexander Clausen
2008-11-16 17:18 ` Mikael Pettersson
2008-11-16 17:24 ` Alexander Clausen
2008-11-16 18:05 ` Alexander Clausen
2008-11-19 8:15 ` Mikael Pettersson
2008-11-22 16:38 ` Mikael Pettersson
2008-11-22 16:49 ` Alexander Clausen
2008-11-22 18:59 ` Alexander Clausen [this message]
2008-11-23 22:07 ` Mikael Pettersson
2008-11-24 12:10 ` Mikael Pettersson
2008-11-24 22:27 ` Alexander Clausen
2008-11-25 21:05 ` Mikael Pettersson
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=4928569C.9080805@gc-web.de \
--to=alex@gc-web.de \
--cc=linux-ide@vger.kernel.org \
--cc=mikpe@it.uu.se \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.