From: Oleg Kravchenko <oleg@kaa.org.ua>
To: Marcel Holtmann <marcel@holtmann.org>
Cc: linux-bluetooth@vger.kernel.org
Subject: Re: BCM2045B2
Date: Thu, 27 Nov 2008 22:02:36 +0200 [thread overview]
Message-ID: <492EFCDC.1050504@kaa.org.ua> (raw)
In-Reply-To: <FE93A0F6-15DB-4F0D-BF59-B719C497E4F3@holtmann.org>
Marcel Holtmann написав(ла):
> Hi Oleg,
>
>> Asus P535 details on http://www.kaa.org.ua/asus-p535/hardware.html
>> Bluetooth chip BCM2045B2 connected to the pxa internal usb host.
>>
>> I think this chip need firmware, because it is can only search
>> How I can upload firmware to the this chip?
>
> no, the chip needs a HCI Reset call. Load btusb with reset=1. And send
> the output of /proc/bus/usb/devices for this dongle.
>
> Regards
>
> Marcel
>
> --
> To unsubscribe from this list: send the line "unsubscribe
> linux-bluetooth" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
I am load modprobe btusb reset=1
Content of /proc/bus/usb/devices:
T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 3
B: Alloc= 22/900 us ( 2%), #Int= 1, #Iso= 0
D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1d6b ProdID=0001 Rev= 2.06
S: Manufacturer=Linux 2.6.27 ohci_hcd
S: Product=PXA27x OHCI
S: SerialNumber=pxa27x
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=255ms
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=12 MxCh= 0
D: Ver= 2.00 Cls=e0(unk. ) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0a5c ProdID=2045 Rev= 1.12
S: Manufacturer=Broadcom Corp
S: Product=BCM2045A
S: SerialNumber=000000000000
C:* #Ifs= 4 Cfg#= 1 Atr=a0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(unk. ) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(unk. ) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(unk. ) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(unk. ) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(unk. ) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(unk. ) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(unk. ) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=84(I) Atr=02(Bulk) MxPS= 32 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 32 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=00 Driver=(none)
When I try establish bnep connection:
localhost ~ # ifconfig bnep0 10.9.0.2
SIOCSIFFLAGS: Cannot assign requested address
So when I enable bluetooth in Windows Mobile
localhost ~ # ifconfig bnep0 10.9.0.2
work's fine :)
This is a Windows bluetooth log:
15:16:55:512 RadioInitPreLoad Start
15:16:55:553 Using USB, no PreLoad code
15:16:55:579 RadioInitPreLoad End
15:16:56:351 RadioInitPostLoad Start
15:16:56:365 BRCM_PostLoad TOP
15:16:56:385 Send_HCI_Read_BDaddr was successful
15:16:56:399 BRCM2045CFG2RAMmain(USB) TOP
15:16:56:412 Sending HCI_DOWNLOAD_MINIDRIVER
15:16:57:946 Writing config binary image through HCI_WRITE_RAM commands
15:16:57:971 Loaded config data file
\Windows\BCM2045B2_002.002.011.0131.0001.hcd, length=9459 bytes
15:16:57:985 Using USB, and using an external .hcd config file
15:16:57:000 target_ram_addr = 0x00:08:5c:70
15:16:57:014 launch_ram_addr = 0x00:08:8b:d8
15:16:57:039 HCIVSWriteRAM(addr=0x70:0x5c:0x08:0x00, nbytes=139)
15:16:57:067 HCIVSWriteRAM(addr=0xf7:0x5c:0x08:0x00, nbytes=255)
15:16:57:106 HCIVSWriteRAM(addr=0xf2:0x5d:0x08:0x00, nbytes=255)
15:16:57:136 HCIVSWriteRAM(addr=0xed:0x5e:0x08:0x00, nbytes=255)
15:16:57:165 HCIVSWriteRAM(addr=0xe8:0x5f:0x08:0x00, nbytes=255)
15:16:57:195 HCIVSWriteRAM(addr=0xe3:0x60:0x08:0x00, nbytes=255)
15:16:57:226 HCIVSWriteRAM(addr=0xde:0x61:0x08:0x00, nbytes=255)
15:16:57:257 HCIVSWriteRAM(addr=0xd9:0x62:0x08:0x00, nbytes=255)
15:16:57:287 HCIVSWriteRAM(addr=0xd4:0x63:0x08:0x00, nbytes=255)
15:16:57:317 HCIVSWriteRAM(addr=0xcf:0x64:0x08:0x00, nbytes=255)
15:16:57:347 HCIVSWriteRAM(addr=0xca:0x65:0x08:0x00, nbytes=255)
15:16:57:377 HCIVSWriteRAM(addr=0xc5:0x66:0x08:0x00, nbytes=255)
15:16:57:429 HCIVSWriteRAM(addr=0xc0:0x67:0x08:0x00, nbytes=255)
15:16:57:459 HCIVSWriteRAM(addr=0xbb:0x68:0x08:0x00, nbytes=255)
15:16:57:489 HCIVSWriteRAM(addr=0xb6:0x69:0x08:0x00, nbytes=255)
15:16:57:553 HCIVSWriteRAM(addr=0xb1:0x6a:0x08:0x00, nbytes=255)
15:16:57:654 HCIVSWriteRAM(addr=0xac:0x6b:0x08:0x00, nbytes=255)
15:16:57:729 HCIVSWriteRAM(addr=0xa7:0x6c:0x08:0x00, nbytes=255)
15:16:58:767 HCIVSWriteRAM(addr=0xa2:0x6d:0x08:0x00, nbytes=255)
15:16:58:890 HCIVSWriteRAM(addr=0x9d:0x6e:0x08:0x00, nbytes=255)
15:16:58:973 HCIVSWriteRAM(addr=0x98:0x6f:0x08:0x00, nbytes=255)
15:16:58:208 HCIVSWriteRAM(addr=0x93:0x70:0x08:0x00, nbytes=255)
15:16:58:384 HCIVSWriteRAM(addr=0x8e:0x71:0x08:0x00, nbytes=255)
15:16:58:607 HCIVSWriteRAM(addr=0x89:0x72:0x08:0x00, nbytes=255)
15:16:58:737 HCIVSWriteRAM(addr=0x84:0x73:0x08:0x00, nbytes=255)
15:16:59:972 HCIVSWriteRAM(addr=0x7f:0x74:0x08:0x00, nbytes=255)
15:16:59:025 HCIVSWriteRAM(addr=0x7a:0x75:0x08:0x00, nbytes=255)
15:16:59:126 HCIVSWriteRAM(addr=0x75:0x76:0x08:0x00, nbytes=255)
15:16:59:155 HCIVSWriteRAM(addr=0x70:0x77:0x08:0x00, nbytes=255)
15:16:59:372 HCIVSWriteRAM(addr=0x6b:0x78:0x08:0x00, nbytes=255)
15:16:59:447 HCIVSWriteRAM(addr=0x66:0x79:0x08:0x00, nbytes=255)
15:16:59:590 HCIVSWriteRAM(addr=0x61:0x7a:0x08:0x00, nbytes=255)
15:16:59:621 HCIVSWriteRAM(addr=0x5c:0x7b:0x08:0x00, nbytes=255)
15:16:59:670 HCIVSWriteRAM(addr=0x57:0x7c:0x08:0x00, nbytes=255)
15:16:59:711 HCIVSWriteRAM(addr=0x52:0x7d:0x08:0x00, nbytes=255)
15:16:59:752 HCIVSWriteRAM(addr=0x4d:0x7e:0x08:0x00, nbytes=255)
15:17:00:807 HCIVSWriteRAM(addr=0x48:0x7f:0x08:0x00, nbytes=222)
15:17:00:930 HCIVSWriteRAM(addr=0xd8:0x8b:0x08:0x00, nbytes=52)
15:17:00:949 HCI_WRITE_RAM commands done
15:17:00:964 Sending HCI_LAUNCH_RAM command
15:17:00:984 HCI_LAUNCH_RAM was successful
15:17:00:499 BRCM2045CFG2RAMmain() END, config data downloaded successfully
15:17:00:519 Send_HCI_Read_BDaddr was successful
15:17:00:534 Read BDAddr [00:1a:92:ab:e3:31] from the registry
15:17:00:554 Send_Broadcom_Write_BD_ADDR was successful
15:17:00:574 Send_HCI_Read_BDaddr was successful
15:17:00:599 HCIWriteChannelClassificationMode : bResult=1
15:17:00:614 HCIVSSetSleepModeParam() Mode=USB with
HOST_WAKE,HostIdleThreshold=10, HCIdleThreshold=10, BT_WAKE active HIGH,
HOST_WAKE active HIGH
15:17:00:628 USB AutoSleepOnSuspend=1, USB Resume Timeout = 3
15:17:00:650 HCIVSSetSleepModeParam(mode=5, timeout=3000ms): bResult=1
15:17:00:665 BRCM_PostLoad : RadioInitConfigureAudio set, configuring
2045 audio
15:17:00:686 HCIVSWriteSCOPCMIntParameters(0,2,0,0,0) : bResult=1
15:17:00:705 HCIVSWritePCMDataFormatParameters(0,0,2,3,1) : bResult=1
15:17:00:721 HCIVSWriteSCOTimeSlot(SCO Time Slot=0)
15:17:00:741 HCIVSWriteSCOTimeSlot : bResult=1
15:17:00:754 BRCM_PostLoad : RadioInitEnableCoexistence set, configuring
2045 BT/WLAN coexistence
15:17:01:774 HCIVSWriteCollaborationMode(1,1,0xcb7fbdb0,10) : bResult=1
15:17:01:787 BRCM_PostLoad END
15:17:01:801 RadioInitPostLoad End
next prev parent reply other threads:[~2008-11-27 20:02 UTC|newest]
Thread overview: 4+ messages / expand[flat|nested] mbox.gz Atom feed top
2008-11-16 12:11 BCM2045B2 Oleg Kravchenko
2008-11-24 2:53 ` BCM2045B2 Marcel Holtmann
2008-11-27 20:02 ` Oleg Kravchenko [this message]
2011-01-16 22:51 ` BCM2045B2 Oleg Kravchenko
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=492EFCDC.1050504@kaa.org.ua \
--to=oleg@kaa.org.ua \
--cc=linux-bluetooth@vger.kernel.org \
--cc=marcel@holtmann.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.