Re: early exception error

[Yinghai Lu <yinghai@kernel.org>]

david@lang.hm wrote:
> On Mon, 5 Jan 2009, Yinghai Lu wrote:
> 
>> Can you send out boot log with working kernel before 2.6.28?
>>
>> need to look at the e820 table.
> 
> 
> here is the 32 bit kernel I'm running now (from dmesg )
> 
> Linux version 2.6.25.14 (root@dlang) (gcc version 3.3.6) #1 SMP PREEMPT
> Mon Aug 4 18:22:50 PDT 2008
> BIOS-provided physical RAM map:
>  BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
>  BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
>  BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
>  BIOS-e820: 0000000000100000 - 000000004cff0000 (usable)
>  BIOS-e820: 000000004cff0000 - 000000004cfff000 (ACPI data)
>  BIOS-e820: 000000004cfff000 - 000000004d000000 (ACPI NVS)
>  BIOS-e820: 00000000ff780000 - 0000000100000000 (reserved)
>  BIOS-e820: 0000000100000000 - 0000000180000000 (usable)
> Warning only 4GB will be used.
> Use a HIGHMEM64G enabled kernel.
> 3200MB HIGHMEM available.
> 896MB LOWMEM available.
> Scan SMP from c0000000 for 1024 bytes.
> Scan SMP from c009fc00 for 1024 bytes.
> Scan SMP from c00f0000 for 65536 bytes.
> found SMP MP-table at [c00ff780] 000ff780
> Entering add_active_range(0, 0, 1048576) 0 entries of 256 used
> Zone PFN ranges:
>   DMA             0 ->     4096
>   Normal       4096 ->   229376
>   HighMem    229376 ->  1048576
> Movable zone start PFN for each node
> early_node_map[1] active PFN ranges
>     0:        0 ->  1048576
> On node 0 totalpages: 1048576
>   DMA zone: 32 pages used for memmap
>   DMA zone: 0 pages reserved
>   DMA zone: 4064 pages, LIFO batch:0
>   Normal zone: 1760 pages used for memmap
>   Normal zone: 223520 pages, LIFO batch:31
>   HighMem zone: 6400 pages used for memmap
>   HighMem zone: 812800 pages, LIFO batch:31
>   Movable zone: 0 pages used for memmap


BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
 BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000004cff0000 (usable)
 BIOS-e820: 000000004cff0000 - 000000004cfff000 (ACPI data)
 BIOS-e820: 000000004cfff000 - 000000004d000000 (ACPI NVS)
 BIOS-e820: 00000000ff780000 - 0000000100000000 (reserved)
 BIOS-e820: 0000000100000000 - 0000000180000000 (usable)

and for pci mem route: node0 [0, 2g), node1 is [4g, 6g)

and e820 said only 3g can be used... [0, 1g), and [4g, 6g)

please check if you can change HW memhole setup to 3g instead 2g.

YH