From: Manu Abraham <abraham.manu@gmail.com>
To: Carl Oscar Ejwertz <oscarmax3@gmail.com>
Cc: linux-media@vger.kernel.org, linux-dvb@linuxtv.org
Subject: Re: [linux-dvb] Mantis Update was Re: Twinhan DTV Ter-CI (3030 Mantis) ???
Date: Sat, 14 Feb 2009 13:40:22 +0400 [thread overview]
Message-ID: <49969186.8030009@gmail.com> (raw)
In-Reply-To: <49968351.50703@gmail.com>
Carl Oscar Ejwertz wrote:
> Sad to say that I still get the same error after a fresh clone and compile. Is
> there any info that I can supply that can help getting this card working?
>
What's the error that you see ?
Did a quick test on the following cards:
VP-1041, VP-2033, VP-3030 The logs look as follows, do you see any
different ?
Regards,
Manu
found a VP-1041 PCI DSS/DVB-S/DVB-S2 device on (04:04.0),
ACPI: PCI Interrupt 0000:04:04.0[A] -> GSI 22 (level, low) -> IRQ 22
Mantis Rev 1 [1822:0031], irq: 22, latency: 32
memory: 0x0, mmio: 0xf93aa000
mantis_stream_control (0): Set stream to HIF
mantis_i2c_init (0): Initializing I2C ..
mantis_i2c_init (0): Disabling I2C interrupt
mantis_i2c_xfer (0): Messages:2
mantis_i2c_write: Address=[0x50] <W>[ 08 ]
mantis_i2c_read: Address=[0x50] <R>[ 00 08 ca 1c 42 c9 ]
MAC Address=[00:08:ca:1c:42:c9]
mantis_dma_init (0): Mantis DMA init
mantis_alloc_buffers (0): DMA=0x325c0000 cpu=0xf25c0000 size=65536
mantis_alloc_buffers (0): RISC=0x32463000 cpu=0xf2463000 size=1000
mantis_calc_lines (0): Mantis RISC block bytes=[4096], line
bytes=[2048], line count=[32]
mantis_dvb_init (0): dvb_register_adapter
DVB: registering new adapter (Mantis DVB adapter)
mantis_dvb_init (0): dvb_dmx_init
mantis_dvb_init (0): dvb_dmxdev_init
mantis_frontend_power (0): Power ON
gpio_set_bits (0): Set Bit <12> to <1>
gpio_set_bits (0): GPIO Value <1000>
gpio_set_bits (0): Set Bit <12> to <1>
gpio_set_bits (0): GPIO Value <1000>
mantis_frontend_soft_reset (0): Frontend RESET
gpio_set_bits (0): Set Bit <13> to <0>
gpio_set_bits (0): GPIO Value <1000>
gpio_set_bits (0): Set Bit <13> to <0>
gpio_set_bits (0): GPIO Value <1000>
gpio_set_bits (0): Set Bit <13> to <1>
gpio_set_bits (0): GPIO Value <3000>
gpio_set_bits (0): Set Bit <13> to <1>
gpio_set_bits (0): GPIO Value <3000>
stb0899_write_regs [0xf1b6]: 02
mantis_i2c_xfer (0): Messages:1
mantis_i2c_write: Address=[0x68] <W>[ f1 b6 02 ]
stb0899_write_regs [0xf1c2]: 00
mantis_i2c_xfer (0): Messages:1
mantis_i2c_write: Address=[0x68] <W>[ f1 c2 00 ]
stb0899_write_regs [0xf1c3]: 00
mantis_i2c_xfer (0): Messages:1
mantis_i2c_write: Address=[0x68] <W>[ f1 c3 00 ]
mantis_i2c_xfer (0): Messages:2
mantis_i2c_write: Address=[0x68] <W>[ f0 00 ]
mantis_i2c_read: Address=[0x68] <R>[ 82 ]
_stb0899_read_reg: Reg=[0xf000], data=82
stb0899_get_dev_id: ID reg=[0x82]
stb0899_get_dev_id: Device ID=[8], Release=[2]
mantis_i2c_xfer (0): Messages:1
mantis_i2c_write: Address=[0x68] <W>[ f3 fc 00 04 00 00 ]
mantis_i2c_xfer (0): Messages:1
mantis_i2c_write: Address=[0x68] <W>[ f3 34 ]
mantis_i2c_xfer (0): Messages:1
mantis_i2c_read: Address=[0x68] <R>[ 31 44 4d 44 ]
mantis_i2c_xfer (0): Messages:1
mantis_i2c_write: Address=[0x68] <W>[ f3 34 ]
mantis_i2c_xfer (0): Messages:1
mantis_i2c_read: Address=[0x68] <R>[ 31 44 4d 44 ]
_stb0899_read_s2reg Device=[0xf3fc], Base address=[0x00000400],
Offset=[0xf334], Data=[0x444d4431]
mantis_i2c_xfer (0): Messages:1
mantis_i2c_write: Address=[0x68] <W>[ f3 fc 00 04 00 00 ]
mantis_i2c_xfer (0): Messages:1
mantis_i2c_write: Address=[0x68] <W>[ f3 00 ]
mantis_i2c_xfer (0): Messages:1
mantis_i2c_read: Address=[0x68] <R>[ 01 00 00 00 ]
mantis_i2c_xfer (0): Messages:1
mantis_i2c_write: Address=[0x68] <W>[ f3 3c ]
mantis_i2c_xfer (0): Messages:1
mantis_i2c_read: Address=[0x68] <R>[ 01 00 00 00 ]
_stb0899_read_s2reg Device=[0xf3fc], Base address=[0x00000400],
Offset=[0xf33c], Data=[0x00000001]
stb0899_get_dev_id: Demodulator Core ID=[DMD1], Version=[1]
mantis_i2c_xfer (0): Messages:1
mantis_i2c_write: Address=[0x68] <W>[ fa fc 00 08 00 00 ]
mantis_i2c_xfer (0): Messages:1
mantis_i2c_write: Address=[0x68] <W>[ fa 00 ]
mantis_i2c_xfer (0): Messages:1
mantis_i2c_read: Address=[0x68] <R>[ 4c 00 00 00 ]
mantis_i2c_xfer (0): Messages:1
mantis_i2c_write: Address=[0x68] <W>[ fa 2c ]
mantis_i2c_xfer (0): Messages:1
mantis_i2c_read: Address=[0x68] <R>[ 31 43 45 46 ]
_stb0899_read_s2reg Device=[0xfafc], Base address=[0x00000800],
Offset=[0xfa2c], Data=[0x46454331]
mantis_i2c_xfer (0): Messages:1
mantis_i2c_write: Address=[0x68] <W>[ fa fc 00 08 00 00 ]
mantis_i2c_xfer (0): Messages:1
mantis_i2c_write: Address=[0x68] <W>[ fa 34 ]
mantis_i2c_xfer (0): Messages:1
mantis_i2c_read: Address=[0x68] <R>[ 01 00 00 00 ]
mantis_i2c_xfer (0): Messages:1
mantis_i2c_write: Address=[0x68] <W>[ fa 34 ]
mantis_i2c_xfer (0): Messages:1
mantis_i2c_read: Address=[0x68] <R>[ 01 00 00 00 ]
_stb0899_read_s2reg Device=[0xfafc], Base address=[0x00000800],
Offset=[0xfa34], Data=[0x00000001]
stb0899_get_dev_id: FEC Core ID=[FEC1], Version=[1]
stb0899_attach: Attaching STB0899
vp1041_frontend_init (0): found STB0899 DVB-S/DVB-S2 frontend @0x68
stb6100_attach: Attaching STB6100
mantis_i2c_xfer (0): Messages:1
mantis_i2c_write: Address=[0x08] <W>[ 40 ]
vp1041_frontend_init (0): Done!
DVB: registering frontend 0 (STB0899 Multistandard)...
found a VP-3030 PCI DVB-T device on (04:04.0),
ACPI: PCI Interrupt 0000:04:04.0[A] -> GSI 22 (level, low) -> IRQ 22
Mantis Rev 1 [1822:0024], irq: 22, latency: 32
memory: 0x0, mmio: 0xf93a8000
mantis_stream_control (0): Set stream to HIF
mantis_i2c_init (0): Initializing I2C ..
mantis_i2c_init (0): Disabling I2C interrupt
mantis_i2c_xfer (0): Messages:2
mantis_i2c_write: Address=[0x50] <W>[ 08 ]
mantis_i2c_read: Address=[0x50] <R>[ 00 08 ca 1a 4d de ]
MAC Address=[00:08:ca:1a:4d:de]
mantis_dma_init (0): Mantis DMA init
mantis_alloc_buffers (0): DMA=0x33450000 cpu=0xf3450000 size=65536
mantis_alloc_buffers (0): RISC=0x334ad000 cpu=0xf34ad000 size=1000
mantis_calc_lines (0): Mantis RISC block bytes=[4096], line
bytes=[2048], line count=[32]
mantis_dvb_init (0): dvb_register_adapter
DVB: registering new adapter (Mantis DVB adapter)
mantis_dvb_init (0): dvb_dmx_init
mantis_dvb_init (0): dvb_dmxdev_init
gpio_set_bits (0): Set Bit <13> to <0>
gpio_set_bits (0): GPIO Value <00>
mantis_frontend_power (0): Power ON
gpio_set_bits (0): Set Bit <12> to <1>
gpio_set_bits (0): GPIO Value <1000>
gpio_set_bits (0): Set Bit <12> to <1>
gpio_set_bits (0): GPIO Value <1000>
gpio_set_bits (0): Set Bit <13> to <1>
gpio_set_bits (0): GPIO Value <3000>
vp3030_frontend_init (0): Probing for 10353 (DVB-T)
mantis_i2c_xfer (0): Messages:2
Byte MODE:
Byte <0> RXD=0x1f7f1480 [14]
tda665x_attach: Attaching TDA665x (ENV57H12D5 (ET-50DT)) tuner
vp3030_frontend_init (0): Done!
DVB: registering frontend 0 (Zarlink ZL10353 DVB-T)...
found a VP-2033 PCI DVB-C device on (04:04.0),
ACPI: PCI Interrupt 0000:04:04.0[A] -> GSI 22 (level, low) -> IRQ 22
Mantis Rev 1 [1822:0008], irq: 22, latency: 32
memory: 0x0, mmio: 0xf93aa000
mantis_stream_control (0): Set stream to HIF
mantis_i2c_init (0): Initializing I2C ..
mantis_i2c_init (0): Disabling I2C interrupt
mantis_i2c_xfer (0): Messages:2
mantis_i2c_write: Address=[0x50] <W>[ 08 I2CDONE: trials=0
I2CRACK: trials=0
]
mantis_i2c_read: Address=[0x50] <R>[ I2CDONE: trials=0
I2CRACK: trials=0
00 I2CDONE: trials=0
I2CRACK: trials=0
08 I2CDONE: trials=0
I2CRACK: trials=0
ca I2CDONE: trials=0
I2CRACK: trials=0
19 I2CDONE: trials=0
I2CRACK: trials=0
ea I2CDONE: trials=0
I2CRACK: trials=0
ee ]
MAC Address=[00:08:ca:19:ea:ee]
mantis_dma_init (0): Mantis DMA init
mantis_alloc_buffers (0): DMA=0x2e580000 cpu=0xee580000 size=65536
mantis_alloc_buffers (0): RISC=0x3254b000 cpu=0xf254b000 size=1000
mantis_calc_lines (0): Mantis RISC block bytes=[4096], line
bytes=[2048], line count=[32]
mantis_dvb_init (0): dvb_register_adapter
DVB: registering new adapter (Mantis DVB adapter)
mantis_dvb_init (0): dvb_dmx_init
mantis_dvb_init (0): dvb_dmxdev_init
mantis_frontend_power (0): Power ON
gpio_set_bits (0): Set Bit <12> to <1>
gpio_set_bits (0): GPIO Value <3001>
gpio_set_bits (0): Set Bit <12> to <1>
gpio_set_bits (0): GPIO Value <3001>
mantis_frontend_soft_reset (0): Frontend RESET
gpio_set_bits (0): Set Bit <13> to <0>
gpio_set_bits (0): GPIO Value <1001>
gpio_set_bits (0): Set Bit <13> to <0>
gpio_set_bits (0): GPIO Value <1001>
gpio_set_bits (0): Set Bit <13> to <1>
gpio_set_bits (0): GPIO Value <3001>
gpio_set_bits (0): Set Bit <13> to <1>
gpio_set_bits (0): GPIO Value <3001>
vp2033_frontend_init (0): Probing for CU1216 (DVB-C)
mantis_i2c_xfer (0): Messages:2
mantis_i2c_write: Address=[0x50] <W>[ ff I2CDONE: trials=0
I2CRACK: trials=0
]
mantis_i2c_read: Address=[0x50] <R>[ I2CDONE: trials=0
I2CRACK: trials=0
22 ]
mantis_i2c_xfer (0): Messages:2
mantis_i2c_write: Address=[0x0c] <W>[ 1a I2CDONE: trials=0
I2CRACK: trials=0
]
mantis_i2c_read: Address=[0x0c] <R>[ I2CDONE: trials=0
I2CRACK: trials=0
7c ]
TDA10021: i2c-addr = 0x0c, id = 0x7c
vp2033_frontend_init (0): found Philips CU1216 DVB-C frontend
(TDA10021) @ 0x0c
vp2033_frontend_init (0): Mantis DVB-C Philips CU1216 frontend
attach success
vp2033_frontend_init (0): Done!
DVB: registering frontend 0 (Philips TDA10021 DVB-C)...
next prev parent reply other threads:[~2009-02-14 9:40 UTC|newest]
Thread overview: 16+ messages / expand[flat|nested] mbox.gz Atom feed top
2009-01-31 23:45 [linux-dvb] Twinhan DTV Ter-CI (3030 Mantis) ??? Carl Oscar Ejwertz
2009-02-05 23:41 ` Mantis Update was " Manu Abraham
2009-02-07 20:23 ` [linux-dvb] Mantis Update was " Ruediger Dohmhardt
2009-02-07 21:45 ` Manu Abraham
2009-02-07 22:03 ` [linux-dvb] 2033 not working with changeset 9143 Ruediger Dohmhardt
2009-02-08 8:34 ` Bob Deblier
2009-02-12 19:20 ` Manu Abraham
2009-02-12 19:22 ` [linux-dvb] Mantis Update was Re: Twinhan DTV Ter-CI (3030 Mantis) ??? Manu Abraham
2009-02-13 19:44 ` Bob Deblier
2009-02-08 16:20 ` Carl Oscar Ejwertz
2009-02-12 19:19 ` Manu Abraham
2009-02-14 8:39 ` Carl Oscar Ejwertz
2009-02-14 9:40 ` Manu Abraham [this message]
2009-02-15 20:51 ` Ruediger Dohmhardt
[not found] <mailman.1.1233918001.5267.linux-dvb@linuxtv.org>
2009-02-06 18:11 ` Mårten Gustafsson
2009-02-07 22:07 ` Manu Abraham
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=49969186.8030009@gmail.com \
--to=abraham.manu@gmail.com \
--cc=linux-dvb@linuxtv.org \
--cc=linux-media@vger.kernel.org \
--cc=oscarmax3@gmail.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.