From: RONETIX - Ilko Iliev <iliev@ronetix.at>
To: u-boot@lists.denx.de
Subject: [U-Boot] [PATCH 1/1] at91: add support for the PM9263 board of Ronetix
Date: Tue, 31 Mar 2009 16:16:46 +0200 [thread overview]
Message-ID: <49D225CE.1080203@ronetix.at> (raw)
The PM9263 board is based on the AT91SAM9263-EK board.
Here is the page on Ronetix website:
http://www.ronetix.at/starter_kit_9263.html
Signed-off-by: Ilko Iliev <iliev@ronetix.at>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
---
MAINTAINERS | 4 +
MAKEALL | 1 +
Makefile | 4 +
board/ronetix/pm9263/Makefile | 61 +++
board/ronetix/pm9263/config.mk | 1 +
.../lowlevel_init.S => board/ronetix/pm9263/led.c | 32 +-
board/ronetix/pm9263/lowlevel_init.S | 279 +++++++++++++
board/ronetix/pm9263/partition.c | 47 +++
board/ronetix/pm9263/pm9263.c | 413
++++++++++++++++++++
cpu/arm926ejs/at91/Makefile | 5 +-
cpu/arm926ejs/at91/config.mk | 2 +-
cpu/arm926ejs/at91/lowlevel_init.S | 2 +
cpu/arm926ejs/at91/{u-boot.lds => u-boot.lds.S} | 9 +-
include/asm-arm/arch-at91/at91sam9263.h | 1 +
include/asm-arm/arch-at91/at91sam9_sdramc.h | 87 ++++
include/asm-arm/arch-at91/hardware.h | 17 +
include/configs/pm9263.h | 367 +++++++++++++++++
tools/Makefile | 3 +
tools/logos/ronetix.bmp | Bin 0 -> 5638 bytes
19 files changed, 1315 insertions(+), 20 deletions(-)
create mode 100644 board/ronetix/pm9263/Makefile
create mode 100644 board/ronetix/pm9263/config.mk
copy cpu/arm926ejs/at91/lowlevel_init.S => board/ronetix/pm9263/led.c (65%)
create mode 100644 board/ronetix/pm9263/lowlevel_init.S
create mode 100644 board/ronetix/pm9263/partition.c
create mode 100644 board/ronetix/pm9263/pm9263.c
rename cpu/arm926ejs/at91/{u-boot.lds => u-boot.lds.S} (90%)
create mode 100644 include/asm-arm/arch-at91/at91sam9_sdramc.h
create mode 100644 include/configs/pm9263.h
create mode 100644 tools/logos/ronetix.bmp
diff --git a/MAINTAINERS b/MAINTAINERS
index 25b28d6..efd04f0 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -204,6 +204,10 @@ Klaus Heydeck <heydeck@kieback-peter.de>
KUP4K MPC855
KUP4X MPC859
+Ilko Iliev <iliev@ronetix.at>
+
+ PM9263 AT91SAM9263
+
Gary Jennejohn <garyj@denx.de>
quad100hd PPC405EP
diff --git a/MAKEALL b/MAKEALL
index 89f1c55..2cde057 100755
--- a/MAKEALL
+++ b/MAKEALL
@@ -581,6 +581,7 @@ LIST_at91=" \
kb9202 \
mp2usb \
m501sk \
+ pm9263 \
"
#########################################################################
diff --git a/Makefile b/Makefile
index a9f25c9..51cb69d 100644
--- a/Makefile
+++ b/Makefile
@@ -2743,6 +2743,9 @@ at91sam9rlek_config : unconfig
fi;
@$(MKCONFIG) -a at91sam9rlek arm arm926ejs at91sam9rlek atmel at91
+pm9263_config : unconfig
+ @$(MKCONFIG) $(@:_config=) arm arm926ejs pm9263 ronetix at91
+
########################################################################
## ARM Integrator boards - see doc/README-integrator for more info.
integratorap_config \
@@ -3511,6 +3514,7 @@ clean:
$(obj)board/trab/trab_fkt $(obj)board/voiceblue/eeprom \
$(obj)board/armltd/{integratorap,integratorcp}/u-boot.lds \
$(obj)board/{bf533-ezkit,bf533-stamp,bf537-stamp,bf561-ezkit}/u-boot.lds \
+ $(obj)cpu/arm926ejs/at91/u-boot.lds \
$(obj)cpu/blackfin/bootrom-asm-offsets.[chs]
@rm -f $(obj)include/bmp_logo.h
@rm -f $(obj)nand_spl/{u-boot-spl,u-boot-spl.map,System.map}
diff --git a/board/ronetix/pm9263/Makefile b/board/ronetix/pm9263/Makefile
new file mode 100644
index 0000000..270abd8
--- /dev/null
+++ b/board/ronetix/pm9263/Makefile
@@ -0,0 +1,61 @@
+#
+# (C) Copyright 2003-2008
+# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
+#
+# (C) Copyright 2008
+# Stelian Pop <stelian.pop@leadtechdesign.com>
+# Lead Tech Design <www.leadtechdesign.com>
+# Ilko Iliev <www.ronetix.at>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB = $(obj)lib$(BOARD).a
+
+COBJS-y += pm9263.o
+COBJS-y += led.o
+COBJS-$(CONFIG_HAS_DATAFLASH) += partition.o
+
+ifndef CONFIG_SKIP_LOWLEVEL_INIT
+SOBJS-y := lowlevel_init.o
+endif
+
+SRCS := $(SOBJS-y:.o=.S) $(COBJS-y:.o=.c)
+OBJS := $(addprefix $(obj),$(COBJS-y) $(SOBJS-y))
+SOBJS := $(addprefix $(obj),$(SOBJS-y))
+
+$(LIB): $(obj).depend $(OBJS) $(SOBJS)
+ $(AR) $(ARFLAGS) $@ $(OBJS)
+
+clean:
+ rm -f $(SOBJS) $(OBJS)
+
+distclean: clean
+ rm -f $(LIB) core *.bak $(obj).depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/board/ronetix/pm9263/config.mk b/board/ronetix/pm9263/config.mk
new file mode 100644
index 0000000..ff2cfd1
--- /dev/null
+++ b/board/ronetix/pm9263/config.mk
@@ -0,0 +1 @@
+TEXT_BASE = 0x23f00000
diff --git a/cpu/arm926ejs/at91/lowlevel_init.S b/board/ronetix/pm9263/led.c
similarity index 65%
copy from cpu/arm926ejs/at91/lowlevel_init.S
copy to board/ronetix/pm9263/led.c
index ec6ad5d..fe1a1d2 100644
--- a/cpu/arm926ejs/at91/lowlevel_init.S
+++ b/board/ronetix/pm9263/led.c
@@ -1,9 +1,8 @@
/*
- * AT91CAP9/SAM9 setup stuff
- *
* (C) Copyright 2007-2008
* Stelian Pop <stelian.pop@leadtechdesign.com>
* Lead Tech Design <www.leadtechdesign.com>
+ * Ilko Iliev <www.ronetix.at>
*
* See file CREDITS for list of people who contributed to this
* project.
@@ -24,20 +23,21 @@
* MA 02111-1307 USA
*/
-#include <config.h>
-#include <version.h>
-
-#ifndef CONFIG_SKIP_LOWLEVEL_INIT
-
-.globl lowlevel_init
-lowlevel_init:
+#include <common.h>
+#include <asm/arch/at91sam9263.h>
+#include <asm/arch/at91_pmc.h>
+#include <asm/arch/gpio.h>
+#include <asm/arch/io.h>
- /*
- * Clocks/SDRAM initialization is handled by at91bootstrap,
- * no need to do it here...
- */
- mov pc, lr
+void coloured_LED_init(void)
+{
+ /* Enable clock */
+ at91_sys_write(AT91_PMC_PCER, 1 << AT91SAM9263_ID_PIOB |
+ 1 << AT91SAM9263_ID_PIOCDE);
- .ltorg
+ at91_set_gpio_output(CONFIG_RED_LED, 1);
+ at91_set_gpio_output(CONFIG_GREEN_LED, 1);
-#endif /* CONFIG_SKIP_LOWLEVEL_INIT */
+ at91_set_gpio_value(CONFIG_RED_LED, 0);
+ at91_set_gpio_value(CONFIG_GREEN_LED, 1);
+}
diff --git a/board/ronetix/pm9263/lowlevel_init.S
b/board/ronetix/pm9263/lowlevel_init.S
new file mode 100644
index 0000000..7b506ae
--- /dev/null
+++ b/board/ronetix/pm9263/lowlevel_init.S
@@ -0,0 +1,279 @@
+/*
+ * Memory Setup stuff - taken from blob memsetup.S
+ *
+ * Copyright (C) 1999 2000 2001 Erik Mouw (J.A.K.Mouw at its.tudelft.nl) and
+ * Jan-Derk Bakker (J.D.Bakker at its.tudelft.nl)
+ *
+ * Copyright (C) 2008 Ronetix Ilko Iliev (www.ronetix.at)
+ * Copyright (C) 2009 Jean-Christopher PLAGNIOL-VILLARD
<plagnioj@jcrosoft.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <config.h>
+#include <version.h>
+#include <asm/arch/hardware.h>
+#include <asm/arch/at91_pmc.h>
+#include <asm/arch/at91_pio.h>
+#include <asm/arch/at91_rstc.h>
+#include <asm/arch/at91_wdt.h>
+#include <asm/arch/at91sam9_sdramc.h>
+#include <asm/arch/at91sam9_smc.h>
+#include <asm/arch/at91sam9263_matrix.h>
+
+_TEXT_BASE:
+ .word TEXT_BASE
+
+.globl lowlevel_init
+.type lowlevel_init,function
+lowlevel_init:
+
+ mov r5, pc /* r5 = POS1 + 4 current */
+POS1:
+ ldr r0, =POS1 /* r0 = POS1 compile */
+ ldr r2, _TEXT_BASE
+ sub r0, r0, r2 /* r0 = POS1-_TEXT_BASE (POS1 relative) */
+ sub r5, r5, r0 /* r0 = TEXT_BASE-1 */
+ sub r5, r5, #4 /* r1 = text base - current */
+
+ /* memory control configuration 1 */
+ ldr r0, =SMRDATA
+ ldr r2, =SMRDATA1
+ ldr r1, _TEXT_BASE
+ sub r0, r0, r1
+ sub r2, r2, r1
+ add r0, r0, r5
+ add r2, r2, r5
+0:
+ /* the address */
+ ldr r1, [r0], #4
+ /* the value */
+ ldr r3, [r0], #4
+ str r3, [r1]
+ cmp r2, r0
+ bne 0b
+
+/*
----------------------------------------------------------------------------
+ * PMC Init Step 1.
+ *
----------------------------------------------------------------------------
+ * - Check if the PLL is already initialized
+ *
----------------------------------------------------------------------------
+ */
+ ldr r1, =(AT91_BASE_SYS + AT91_PMC_MCKR)
+ ldr r0, [r1]
+ and r0, r0, #3
+ cmp r0, #0
+ bne PLL_setup_end
+
+/*
---------------------------------------------------------------------------
+ * - Enable the Main Oscillator
+ *
---------------------------------------------------------------------------
+ */
+ ldr r1, =(AT91_BASE_SYS + AT91_CKGR_MOR)
+ ldr r2, =(AT91_BASE_SYS + AT91_PMC_SR)
+ ldr r0, =0x0000FF01
+ str r0, [r1] /* Enable main oscillator, OSCOUNT = 0xFF */
+
+ /* Reading the PMC Status to detect when the Main Oscillator is
enabled */
+ mov r4, #AT91_PMC_MOSCS
+MOSCS_Loop:
+ ldr r3, [r2]
+ and r3, r4, r3
+ cmp r3, #AT91_PMC_MOSCS
+ bne MOSCS_Loop
+
+/*
----------------------------------------------------------------------------
+ * PMC Init Step 2.
+ *
----------------------------------------------------------------------------
+ * Setup PLLA
+ *
----------------------------------------------------------------------------
+ */
+ ldr r1, =(AT91_BASE_SYS + AT91_CKGR_PLLAR)
+ ldr r0, =CONFIG_SYS_PLLAR_VAL
+ str r0, [r1]
+
+ /* Reading the PMC Status register to detect when the PLLA is locked */
+ mov r4, #AT91_PMC_LOCKA
+MOSCS_Loop1:
+ ldr r3, [r2]
+ and r3, r4, r3
+ cmp r3, #AT91_PMC_LOCKA
+ bne MOSCS_Loop1
+
+/*
----------------------------------------------------------------------------
+ * PMC Init Step 3.
+ *
----------------------------------------------------------------------------
+ * - Switch on the Main Oscillator 18.432 MHz
+ *
----------------------------------------------------------------------------
+ */
+ ldr r1, =(AT91_BASE_SYS + AT91_PMC_MCKR)
+
+ /* -Master Clock Controller register PMC_MCKR */
+ ldr r0, =CONFIG_SYS_MCKR1_VAL
+ str r0, [r1]
+
+ /* Reading the PMC Status to detect when the Master clock is ready */
+ mov r4, #AT91_PMC_MCKRDY
+MCKRDY_Loop:
+ ldr r3, [r2]
+ and r3, r4, r3
+ cmp r3, #AT91_PMC_MCKRDY
+ bne MCKRDY_Loop
+
+ ldr r0, =CONFIG_SYS_MCKR2_VAL
+ str r0, [r1]
+
+ /* Reading the PMC Status to detect when the Master clock is ready */
+ mov r4, #AT91_PMC_MCKRDY
+MCKRDY_Loop1:
+ ldr r3, [r2]
+ and r3, r4, r3
+ cmp r3, #AT91_PMC_MCKRDY
+ bne MCKRDY_Loop1
+
+PLL_setup_end:
+
+/*
----------------------------------------------------------------------------
+ * - memory control configuration 2
+ *
----------------------------------------------------------------------------
+ */
+ ldr r0, =(AT91_BASE_SYS + AT91_SDRAMC_TR)
+ ldr r1, [r0]
+ cmp r1, #0
+ bne SDRAM_setup_end
+
+ ldr r0, =SMRDATA1
+ ldr r2, =SMRDATA2
+ ldr r1, _TEXT_BASE
+ sub r0, r0, r1
+ sub r2, r2, r1
+ add r0, r0, r5
+ add r2, r2, r5
+
+2:
+ /* the address */
+ ldr r1, [r0], #4
+ /* the value */
+ ldr r3, [r0], #4
+ str r3, [r1]
+ cmp r2, r0
+ bne 2b
+
+SDRAM_setup_end:
+ /* everything is fine now */
+ mov pc, lr
+
+ .ltorg
+
+SMRDATA:
+ .word (AT91_BASE_SYS + AT91_WDT_MR)
+ .word CONFIG_SYS_WDTC_WDMR_VAL
+
+ .word (AT91_BASE_SYS + AT91_PIOD + PIO_PDR)
+ .word CONFIG_SYS_PIOD_PDR_VAL1
+ .word (AT91_BASE_SYS + AT91_PIOD + PIO_PUDR)
+ .word CONFIG_SYS_PIOD_PPUDR_VAL
+ .word (AT91_BASE_SYS + AT91_PIOD + PIO_ASR)
+ .word CONFIG_SYS_PIOD_PPUDR_VAL
+
+ .word (AT91_BASE_SYS + AT91_MATRIX_EBI0CSA)
+ .word CONFIG_SYS_MATRIX_EBI0CSA_VAL
+ .word (AT91_BASE_SYS + AT91_MATRIX_EBI1CSA)
+ .word CONFIG_SYS_MATRIX_EBI1CSA_VAL
+
+ /* flash */
+ .word (AT91_BASE_SYS + AT91_SMC_MODE(0))
+ .word CONFIG_SYS_SMC0_CTRL0_VAL
+
+ .word (AT91_BASE_SYS + AT91_SMC_CYCLE(0))
+ .word CONFIG_SYS_SMC0_CYCLE0_VAL
+
+ .word (AT91_BASE_SYS + AT91_SMC_PULSE(0))
+ .word CONFIG_SYS_SMC0_PULSE0_VAL
+
+ .word (AT91_BASE_SYS + AT91_SMC_SETUP(0))
+ .word CONFIG_SYS_SMC0_SETUP0_VAL
+
+ /* PSRAM */
+ .word (AT91_BASE_SYS + AT91_SMC1_MODE(0))
+ .word CONFIG_SYS_SMC1_CTRL0_VAL
+
+ .word (AT91_BASE_SYS + AT91_SMC1_CYCLE(0))
+ .word CONFIG_SYS_SMC1_CYCLE0_VAL
+
+ .word (AT91_BASE_SYS + AT91_SMC1_PULSE(0))
+ .word CONFIG_SYS_SMC1_PULSE0_VAL
+
+ .word (AT91_BASE_SYS + AT91_SMC1_SETUP(0))
+ .word CONFIG_SYS_SMC1_SETUP0_VAL
+
+SMRDATA1:
+ .word (AT91_BASE_SYS + AT91_SDRAMC_MR)
+ .word CONFIG_SYS_SDRC_MR_VAL1
+ .word (AT91_BASE_SYS + AT91_SDRAMC_TR)
+ .word CONFIG_SYS_SDRC_TR_VAL1
+ .word (AT91_BASE_SYS + AT91_SDRAMC_CR)
+ .word CONFIG_SYS_SDRC_CR_VAL
+ .word (AT91_BASE_SYS + AT91_SDRAMC_MDR)
+ .word CONFIG_SYS_SDRC_MDR_VAL
+ .word (AT91_BASE_SYS + AT91_SDRAMC_MR)
+ .word CONFIG_SYS_SDRC_MR_VAL2
+ .word AT91_SDRAM_BASE
+ .word CONFIG_SYS_SDRAM_VAL1
+ .word (AT91_BASE_SYS + AT91_SDRAMC_MR)
+ .word CONFIG_SYS_SDRC_MR_VAL3
+ .word AT91_SDRAM_BASE
+ .word CONFIG_SYS_SDRAM_VAL2
+ .word AT91_SDRAM_BASE
+ .word CONFIG_SYS_SDRAM_VAL3
+ .word AT91_SDRAM_BASE
+ .word CONFIG_SYS_SDRAM_VAL4
+ .word AT91_SDRAM_BASE
+ .word CONFIG_SYS_SDRAM_VAL5
+ .word AT91_SDRAM_BASE
+ .word CONFIG_SYS_SDRAM_VAL6
+ .word AT91_SDRAM_BASE
+ .word CONFIG_SYS_SDRAM_VAL7
+ .word AT91_SDRAM_BASE
+ .word CONFIG_SYS_SDRAM_VAL8
+ .word AT91_SDRAM_BASE
+ .word CONFIG_SYS_SDRAM_VAL9
+ .word (AT91_BASE_SYS + AT91_SDRAMC_MR)
+ .word CONFIG_SYS_SDRC_MR_VAL4
+ .word AT91_SDRAM_BASE
+ .word CONFIG_SYS_SDRAM_VAL10
+ .word (AT91_BASE_SYS + AT91_SDRAMC_MR)
+ .word CONFIG_SYS_SDRC_MR_VAL5
+ .word AT91_SDRAM_BASE
+ .word CONFIG_SYS_SDRAM_VAL11
+ .word (AT91_BASE_SYS + AT91_SDRAMC_TR)
+ .word CONFIG_SYS_SDRC_TR_VAL2
+ .word AT91_SDRAM_BASE
+ .word CONFIG_SYS_SDRAM_VAL12
+ /* User reset enable*/
+ .word (AT91_BASE_SYS + AT91_RSTC_MR)
+ .word CONFIG_SYS_RSTC_RMR_VAL
+#ifdef CONFIG_SYS_MATRIX_MCFG_REMAP
+ /* MATRIX_MCFG - REMAP all masters */
+ .word (AT91_BASE_SYS + AT91_MATRIX_MCFG0)
+ .word 0x1FF
+#endif
+
+SMRDATA2:
+ .word 0
diff --git a/board/ronetix/pm9263/partition.c
b/board/ronetix/pm9263/partition.c
new file mode 100644
index 0000000..95ac398
--- /dev/null
+++ b/board/ronetix/pm9263/partition.c
@@ -0,0 +1,47 @@
+/*
+ * (C) Copyright 2008
+ * Ulf Samuelsson <ulf@atmel.com>
+ * Ilko Iliev <www.ronetix.at>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ *
+ */
+#include <common.h>
+#include <config.h>
+#include <asm/hardware.h>
+#include <dataflash.h>
+
+AT91S_DATAFLASH_INFO dataflash_info[CONFIG_SYS_MAX_DATAFLASH_BANKS];
+
+struct dataflash_addr cs[CONFIG_SYS_MAX_DATAFLASH_BANKS] = {
+ {CONFIG_SYS_DATAFLASH_LOGIC_ADDR_CS0, 0}, /* Logical adress, CS */
+};
+
+/*define the area offsets*/
+#ifdef CONFIG_SYS_USE_DATAFLASH
+dataflash_protect_t area_list[NB_DATAFLASH_AREA] = {
+ {0x00000000, 0x000041FF, FLAG_PROTECT_SET, 0, "Bootstrap"},
+ {0x00004200, 0x000083FF, FLAG_PROTECT_CLEAR, 0, "Environment"},
+ {0x00008400, 0x00041FFF, FLAG_PROTECT_SET, 0, "U-Boot"},
+ {0x00042000, 0x00251FFF, FLAG_PROTECT_CLEAR, 0, "Kernel"},
+ {0x00252000, 0xFFFFFFFF, FLAG_PROTECT_CLEAR, 0, "FS"},
+};
+#else
+dataflash_protect_t area_list[NB_DATAFLASH_AREA] = {
+ {0x00000000, 0xFFFFFFFF, FLAG_PROTECT_CLEAR, 0, ""},
+};
+
+#endif
diff --git a/board/ronetix/pm9263/pm9263.c b/board/ronetix/pm9263/pm9263.c
new file mode 100644
index 0000000..801b268
--- /dev/null
+++ b/board/ronetix/pm9263/pm9263.c
@@ -0,0 +1,413 @@
+/*
+ * (C) Copyright 2007-2008
+ * Stelian Pop <stelian.pop@leadtechdesign.com>
+ * Lead Tech Design <www.leadtechdesign.com>
+ * Copyright (C) 2008 Ronetix Ilko Iliev (www.ronetix.at)
+ * Copyright (C) 2009 Jean-Christopher PLAGNIOL-VILLARD
<plagnioj@jcrosoft.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/sizes.h>
+#include <asm/arch/at91sam9263.h>
+#include <asm/arch/at91sam9263_matrix.h>
+#include <asm/arch/at91sam9_smc.h>
+#include <asm/arch/at91_common.h>
+#include <asm/arch/at91_pmc.h>
+#include <asm/arch/at91_rstc.h>
+#include <asm/arch/clk.h>
+#include <asm/arch/gpio.h>
+#include <asm/arch/io.h>
+#include <asm/arch/hardware.h>
+#include <lcd.h>
+#include <atmel_lcdc.h>
+#include <dataflash.h>
+#if defined(CONFIG_RESET_PHY_R) && defined(CONFIG_MACB)
+#include <net.h>
+#endif
+#include <netdev.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+/*
------------------------------------------------------------------------- */
+/*
+ * Miscelaneous platform dependent initialisations
+ */
+
+#ifdef CONFIG_CMD_NAND
+static void pm9263_nand_hw_init(void)
+{
+ unsigned long csa;
+
+ /* Enable CS3 */
+ csa = at91_sys_read(AT91_MATRIX_EBI0CSA);
+ at91_sys_write(AT91_MATRIX_EBI0CSA,
+ csa | AT91_MATRIX_EBI0_CS3A_SMC_SMARTMEDIA);
+
+ /* Configure SMC CS3 for NAND/SmartMedia */
+ at91_sys_write(AT91_SMC_SETUP(3),
+ AT91_SMC_NWESETUP_(1) | AT91_SMC_NCS_WRSETUP_(1) |
+ AT91_SMC_NRDSETUP_(1) | AT91_SMC_NCS_RDSETUP_(1));
+ at91_sys_write(AT91_SMC_PULSE(3),
+ AT91_SMC_NWEPULSE_(3) | AT91_SMC_NCS_WRPULSE_(3) |
+ AT91_SMC_NRDPULSE_(3) | AT91_SMC_NCS_RDPULSE_(3));
+ at91_sys_write(AT91_SMC_CYCLE(3),
+ AT91_SMC_NWECYCLE_(5) | AT91_SMC_NRDCYCLE_(5));
+ at91_sys_write(AT91_SMC_MODE(3),
+ AT91_SMC_READMODE | AT91_SMC_WRITEMODE |
+ AT91_SMC_EXNWMODE_DISABLE |
+#ifdef CONFIG_SYS_NAND_DBW_16
+ AT91_SMC_DBW_16 |
+#else /* CONFIG_SYS_NAND_DBW_8 */
+ AT91_SMC_DBW_8 |
+#endif
+ AT91_SMC_TDF_(2));
+
+ /* Configure RDY/BSY */
+ at91_set_gpio_input(CONFIG_SYS_NAND_READY_PIN, 1);
+
+ /* Enable NandFlash */
+ at91_set_gpio_output(CONFIG_SYS_NAND_ENABLE_PIN, 1);
+}
+#endif
+
+#ifdef CONFIG_MACB
+static void pm9263_macb_hw_init(void)
+{
+ /*
+ * PB27 enables the 50MHz oscillator for Ethernet PHY
+ * 1 - enable
+ * 0 - disable
+ */
+ at91_set_gpio_output(AT91_PIN_PB27, 1);
+ at91_set_gpio_value(AT91_PIN_PB27, 1); /* 1- enable, 0 - disable */
+
+ /* Enable clock */
+ at91_sys_write(AT91_PMC_PCER, 1 << AT91SAM9263_ID_EMAC);
+
+ /*
+ * Disable pull-up on:
+ * RXDV (PC25) => PHY normal mode (not Test mode)
+ * ERX0 (PE25) => PHY ADDR0
+ * ERX1 (PE26) => PHY ADDR1 => PHYADDR = 0x0
+ *
+ * PHY has internal pull-down
+ */
+ writel(pin_to_mask(AT91_PIN_PC25),
+ pin_to_controller(AT91_PIN_PC0) + PIO_PUDR);
+ writel(pin_to_mask(AT91_PIN_PE25) |
+ pin_to_mask(AT91_PIN_PE26),
+ pin_to_controller(AT91_PIN_PE0) + PIO_PUDR);
+
+
+ /* Re-enable pull-up */
+ writel(pin_to_mask(AT91_PIN_PC25),
+ pin_to_controller(AT91_PIN_PC0) + PIO_PUER);
+ writel(pin_to_mask(AT91_PIN_PE25) |
+ pin_to_mask(AT91_PIN_PE26),
+ pin_to_controller(AT91_PIN_PE0) + PIO_PUER);
+
+ at91_macb_hw_init();
+}
+#endif
+
+#ifdef CONFIG_LCD
+vidinfo_t panel_info = {
+ vl_col: 240,
+ vl_row: 320,
+ vl_clk: 4965000,
+ vl_sync: ATMEL_LCDC_INVLINE_INVERTED |
+ ATMEL_LCDC_INVFRAME_INVERTED,
+ vl_bpix: 3,
+ vl_tft: 1,
+ vl_hsync_len: 5,
+ vl_left_margin: 1,
+ vl_right_margin:33,
+ vl_vsync_len: 1,
+ vl_upper_margin:1,
+ vl_lower_margin:0,
+ mmio: AT91SAM9263_LCDC_BASE,
+};
+
+void lcd_enable(void)
+{
+ at91_set_gpio_value(AT91_PIN_PA22, 1); /* power up */
+}
+
+void lcd_disable(void)
+{
+ at91_set_gpio_value(AT91_PIN_PA22, 0); /* power down */
+}
+
+#ifdef CONFIG_LCD_IN_PSRAM
+
+#define PSRAM_CRE_PIN AT91_PIN_PB29
+#define PSRAM_CTRL_REG (PHYS_PSRAM + PHYS_PSRAM_SIZE - 2)
+
+/* Initialize the PSRAM memory */
+static int pm9263_lcd_hw_psram_init(void)
+{
+ volatile uint16_t x;
+
+ /* setup PB29 as output */
+ at91_set_gpio_output(PSRAM_CRE_PIN, 1);
+
+ at91_set_gpio_value(PSRAM_CRE_PIN, 0); /* set PSRAM_CRE_PIN to
'0' */
+
+ /* PSRAM: write BCR */
+ x = readw(PSRAM_CTRL_REG);
+ x = readw(PSRAM_CTRL_REG);
+ writew(1, PSRAM_CTRL_REG); /* 0 - RCR,1 - BCR */
+ writew(0x9d4f, PSRAM_CTRL_REG); /* write the BCR */
+
+ /* write RCR of the PSRAM */
+ x = readw(PSRAM_CTRL_REG);
+ x = readw(PSRAM_CTRL_REG);
+ writew(0, PSRAM_CTRL_REG); /* 0 - RCR,1 - BCR */
+ /* set RCR; 0x10-async mode,0x90-page mode */
+ writew(0x90, PSRAM_CTRL_REG);
+
+ /*
+ * test to see if the PSRAM is MT45W2M16A or MT45W2M16B
+ * MT45W2M16B - CRE must be 0
+ * MT45W2M16A - CRE must be 1
+ */
+ writew(0x1234, PHYS_PSRAM);
+ writew(0x5678, PHYS_PSRAM + 2);
+
+ /* test if the chip is MT45W2M16B */
+ if ((readw(PHYS_PSRAM) != 0x1234) || (readw(PHYS_PSRAM+2) != 0x5678)) {
+ /* try with CRE=1 (MT45W2M16A) */
+ at91_set_gpio_value(PSRAM_CRE_PIN, 1); /* set PSRAM_CRE_PIN to
'1' */
+
+ /* write RCR of the PSRAM */
+ x = readw(PSRAM_CTRL_REG);
+ x = readw(PSRAM_CTRL_REG);
+ writew(0, PSRAM_CTRL_REG); /* 0 - RCR,1 - BCR */
+ /* set RCR;0x10-async mode,0x90-page mode */
+ writew(0x90, PSRAM_CTRL_REG);
+
+
+ writew(0x1234, PHYS_PSRAM);
+ writew(0x5678, PHYS_PSRAM+2);
+ if ((readw(PHYS_PSRAM) != 0x1234)
+ || (readw(PHYS_PSRAM + 2) != 0x5678))
+ return 1;
+
+ }
+
+ /* Bus matrix */
+ at91_sys_write( AT91_MATRIX_PRAS5, AT91_MATRIX_M5PR );
+ at91_sys_write( AT91_MATRIX_SCFG5, AT91_MATRIX_ARBT_FIXED_PRIORITY |
+ (AT91_MATRIX_FIXED_DEFMSTR & (5 << 18)) |
+ AT91_MATRIX_DEFMSTR_TYPE_FIXED |
+ (AT91_MATRIX_SLOT_CYCLE & (0x80 << 0)));
+
+ return 0;
+}
+#endif
+
+static void pm9263_lcd_hw_init(void)
+{
+ at91_set_A_periph(AT91_PIN_PC0, 0); /* LCDVSYNC */
+ at91_set_A_periph(AT91_PIN_PC1, 0); /* LCDHSYNC */
+ at91_set_A_periph(AT91_PIN_PC2, 0); /* LCDDOTCK */
+ at91_set_A_periph(AT91_PIN_PC3, 0); /* LCDDEN */
+ at91_set_B_periph(AT91_PIN_PB9, 0); /* LCDCC */
+ at91_set_A_periph(AT91_PIN_PC6, 0); /* LCDD2 */
+ at91_set_A_periph(AT91_PIN_PC7, 0); /* LCDD3 */
+ at91_set_A_periph(AT91_PIN_PC8, 0); /* LCDD4 */
+ at91_set_A_periph(AT91_PIN_PC9, 0); /* LCDD5 */
+ at91_set_A_periph(AT91_PIN_PC10, 0); /* LCDD6 */
+ at91_set_A_periph(AT91_PIN_PC11, 0); /* LCDD7 */
+ at91_set_A_periph(AT91_PIN_PC14, 0); /* LCDD10 */
+ at91_set_A_periph(AT91_PIN_PC15, 0); /* LCDD11 */
+ at91_set_A_periph(AT91_PIN_PC16, 0); /* LCDD12 */
+ at91_set_B_periph(AT91_PIN_PC12, 0); /* LCDD13 */
+ at91_set_A_periph(AT91_PIN_PC18, 0); /* LCDD14 */
+ at91_set_A_periph(AT91_PIN_PC19, 0); /* LCDD15 */
+ at91_set_A_periph(AT91_PIN_PC22, 0); /* LCDD18 */
+ at91_set_A_periph(AT91_PIN_PC23, 0); /* LCDD19 */
+ at91_set_A_periph(AT91_PIN_PC24, 0); /* LCDD20 */
+ at91_set_B_periph(AT91_PIN_PC17, 0); /* LCDD21 */
+ at91_set_A_periph(AT91_PIN_PC26, 0); /* LCDD22 */
+ at91_set_A_periph(AT91_PIN_PC27, 0); /* LCDD23 */
+
+ at91_sys_write(AT91_PMC_PCER, 1 << AT91SAM9263_ID_LCDC);
+
+ /* Power Control */
+ at91_set_gpio_output(AT91_PIN_PA22, 1);
+ at91_set_gpio_value(AT91_PIN_PA22, 0); /* power down */
+
+#ifdef CONFIG_LCD_IN_PSRAM
+ /* initialize te PSRAM */
+ int stat = pm9263_lcd_hw_psram_init();
+
+ gd->fb_base = (stat == 0) ? PHYS_PSRAM : AT91SAM9263_SRAM0_BASE;
+#else
+ gd->fb_base = AT91SAM9263_SRAM0_BASE;
+#endif
+
+}
+
+#ifdef CONFIG_LCD_INFO
+#include <nand.h>
+#include <version.h>
+
+extern flash_info_t flash_info[];
+
+void lcd_show_board_info(void)
+{
+ ulong dram_size, nand_size, flash_size, dataflash_size;
+ int i;
+ char temp[32];
+
+ lcd_printf ("%s\n", U_BOOT_VERSION);
+ lcd_printf ("(C) 2009 Ronetix GmbH\n");
+ lcd_printf ("support at ronetix.at\n");
+ lcd_printf ("%s CPU at %s MHz",
+ AT91_CPU_NAME,
+ strmhz(temp, get_cpu_clk_rate()));
+
+ dram_size = 0;
+ for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++)
+ dram_size += gd->bd->bi_dram[i].size;
+
+ nand_size = 0;
+ for (i = 0; i < CONFIG_SYS_MAX_NAND_DEVICE; i++)
+ nand_size += nand_info[i].size;
+
+ flash_size = 0;
+ for (i = 0; i < CONFIG_SYS_MAX_FLASH_BANKS; i++)
+ flash_size += flash_info[i].size;
+
+ dataflash_size = 0;
+ for (i = 0; i < CONFIG_SYS_MAX_DATAFLASH_BANKS; i++)
+ dataflash_size += (unsigned int)
dataflash_info[i].Device.pages_number *
+ dataflash_info[i].Device.pages_size;
+
+ lcd_printf ("%ld MB SDRAM, %ld MB NAND\n%ld MB NOR Flash\n"
+ "4 MB PSRAM, %ld MB DataFlash\n",
+ dram_size >> 20,
+ nand_size >> 20,
+ flash_size >> 20,
+ dataflash_size >> 20);
+}
+#endif /* CONFIG_LCD_INFO */
+
+#endif /* CONFIG_LCD */
+
+int board_init(void)
+{
+ /* Enable Ctrlc */
+ console_init_f();
+
+ at91_sys_write(AT91_PMC_PCER,
+ (1 << AT91SAM9263_ID_PIOA) |
+ (1 << AT91SAM9263_ID_PIOCDE) |
+ (1 << AT91SAM9263_ID_PIOB));
+
+ /* arch number of AT91SAM9263EK-Board */
+ gd->bd->bi_arch_number = MACH_TYPE_PM9263;
+
+ /* adress of boot parameters */
+ gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
+
+ at91_serial_hw_init();
+#ifdef CONFIG_CMD_NAND
+ pm9263_nand_hw_init();
+#endif
+#ifdef CONFIG_HAS_DATAFLASH
+ at91_spi0_hw_init(1 << 0);
+#endif
+#ifdef CONFIG_MACB
+ pm9263_macb_hw_init();
+#endif
+#ifdef CONFIG_USB_OHCI_NEW
+ at91_uhp_hw_init();
+#endif
+#ifdef CONFIG_LCD
+ pm9263_lcd_hw_init();
+#endif
+ return 0;
+}
+
+int dram_init(void)
+{
+ gd->bd->bi_dram[0].start = PHYS_SDRAM;
+ gd->bd->bi_dram[0].size = PHYS_SDRAM_SIZE;
+ return 0;
+}
+
+#ifdef CONFIG_RESET_PHY_R
+void reset_phy(void)
+{
+#ifdef CONFIG_MACB
+ /*
+ * Initialize ethernet HW addr prior to starting Linux,
+ * needed for nfsroot
+ */
+ eth_init(gd->bd);
+#endif
+}
+#endif
+
+int board_eth_init(bd_t *bis)
+{
+ int rc = 0;
+#ifdef CONFIG_MACB
+ rc = macb_eth_initialize(0, (void *)AT91SAM9263_BASE_EMAC, 0x01);
+#endif
+ return rc;
+}
+
+#ifdef CONFIG_DISPLAY_BOARDINFO
+int checkboard (void)
+{
+ char *ss;
+ char buf[32];
+
+ printf ("Board : Ronetix PM9263\n");
+ printf ("Crystal frequency: %8s MHz\n",
+ strmhz(buf, get_main_clk_rate()));
+ printf ("CPU clock : %8s MHz\n",
+ strmhz(buf, get_cpu_clk_rate()));
+ printf ("Master clock : %8s MHz\n",
+ strmhz(buf, get_mck_clk_rate()));
+
+ switch (gd->fb_base) {
+ case PHYS_PSRAM:
+ ss = "(PSRAM)";
+ break;
+
+ case AT91SAM9263_SRAM0_BASE:
+ ss = "(Internal SRAM)";
+ break;
+
+ default:
+ ss = "";
+ break;
+ }
+ printf("Video memory : 0x%08lX %s\n", gd->fb_base, ss );
+
+ printf ("\n");
+ return 0;
+}
+#endif
diff --git a/cpu/arm926ejs/at91/Makefile b/cpu/arm926ejs/at91/Makefile
index 275673c..685cee1 100644
--- a/cpu/arm926ejs/at91/Makefile
+++ b/cpu/arm926ejs/at91/Makefile
@@ -69,11 +69,14 @@ SOBJS = lowlevel_init.o
SRCS := $(SOBJS:.o=.S) $(COBJS-y:.o=.c)
OBJS := $(addprefix $(obj),$(SOBJS) $(COBJS-y))
-all: $(obj).depend $(LIB)
+all: $(obj).depend $(LIB) $(obj)u-boot.lds
$(LIB): $(OBJS)
$(AR) $(ARFLAGS) $@ $(OBJS)
+$(obj)u-boot.lds: u-boot.lds.S
+ $(CPP) $(CPPFLAGS) -D__ASSEMBLY__ -DCONFIG_BOARDDIR=$(BOARDDIR) -P
$^ > $@
+
#########################################################################
# defines $(obj).depend target
diff --git a/cpu/arm926ejs/at91/config.mk b/cpu/arm926ejs/at91/config.mk
index 06177e6..147bd4c 100644
--- a/cpu/arm926ejs/at91/config.mk
+++ b/cpu/arm926ejs/at91/config.mk
@@ -1,2 +1,2 @@
PLATFORM_CPPFLAGS += $(call cc-option,-mtune=arm926ejs,)
-LDSCRIPT := $(SRCTREE)/cpu/arm926ejs/at91/u-boot.lds
+LDSCRIPT := $(OBJTREE)/cpu/arm926ejs/at91/u-boot.lds
diff --git a/cpu/arm926ejs/at91/lowlevel_init.S
b/cpu/arm926ejs/at91/lowlevel_init.S
index ec6ad5d..54b3f3d 100644
--- a/cpu/arm926ejs/at91/lowlevel_init.S
+++ b/cpu/arm926ejs/at91/lowlevel_init.S
@@ -30,6 +30,8 @@
#ifndef CONFIG_SKIP_LOWLEVEL_INIT
.globl lowlevel_init
+.weak lowlevel_init
+.set lowlevel_init,function
lowlevel_init:
/*
diff --git a/cpu/arm926ejs/at91/u-boot.lds b/cpu/arm926ejs/at91/u-boot.lds.S
similarity index 90%
rename from cpu/arm926ejs/at91/u-boot.lds
rename to cpu/arm926ejs/at91/u-boot.lds.S
index ebb1f93..4e82bca 100644
--- a/cpu/arm926ejs/at91/u-boot.lds
+++ b/cpu/arm926ejs/at91/u-boot.lds.S
@@ -21,6 +21,8 @@
* MA 02111-1307 USA
*/
+#include <config.h>
+
OUTPUT_FORMAT("elf32-littlearm", "elf32-littlearm", "elf32-littlearm")
/*OUTPUT_FORMAT("elf32-arm", "elf32-arm", "elf32-arm")*/
OUTPUT_ARCH(arm)
@@ -32,8 +34,11 @@ SECTIONS
. = ALIGN(4);
.text :
{
- cpu/arm926ejs/start.o (.text)
- *(.text)
+ cpu/arm926ejs/start.o (.text)
+#ifndef CONFIG_SKIP_LOWLEVEL_INIT
+ board/CONFIG_BOARDDIR/lowlevel_init.o (.text)
+#endif
+ *(.text)
}
. = ALIGN(4);
diff --git a/include/asm-arm/arch-at91/at91sam9263.h
b/include/asm-arm/arch-at91/at91sam9263.h
index 98251cb..07b265f 100644
--- a/include/asm-arm/arch-at91/at91sam9263.h
+++ b/include/asm-arm/arch-at91/at91sam9263.h
@@ -106,6 +106,7 @@
#define AT91_USART2 AT91SAM9263_BASE_US2
#define AT91_SMC AT91_SMC0
+#define AT91_SDRAMC AT91_SDRAMC0
/*
* Internal Memory.
diff --git a/include/asm-arm/arch-at91/at91sam9_sdramc.h
b/include/asm-arm/arch-at91/at91sam9_sdramc.h
new file mode 100644
index 0000000..5af2b54
--- /dev/null
+++ b/include/asm-arm/arch-at91/at91sam9_sdramc.h
@@ -0,0 +1,87 @@
+/*
+ * [origin: Linux kernel arch/arm/mach-at91/include/mach/at91_wdt.h]
+ *
+ * Copyright (C) 2009 Jean-Christophe PLAGNIOL-VILLARD
<plagnioj@jcrosoft.com>
+ * Copyright (C) 2007 Andrew Victor
+ * Copyright (C) 2007 Atmel Corporation.
+ *
+ * SDRAM Controllers (SDRAMC) - System peripherals registers.
+ * Based on AT91SAM9261 datasheet revision D.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#ifndef AT91SAM9_SDRAMC_H
+#define AT91SAM9_SDRAMC_H
+
+/* SDRAM Controller (SDRAMC) registers */
+#define AT91_SDRAMC_MR (AT91_SDRAMC + 0x00) /* SDRAM
Controller Mode Register */
+#define AT91_SDRAMC_MODE (0xf << 0) /* Command Mode */
+#define AT91_SDRAMC_MODE_NORMAL 0
+#define AT91_SDRAMC_MODE_NOP 1
+#define AT91_SDRAMC_MODE_PRECHARGE 2
+#define AT91_SDRAMC_MODE_LMR 3
+#define AT91_SDRAMC_MODE_REFRESH 4
+#define AT91_SDRAMC_MODE_EXT_LMR 5
+#define AT91_SDRAMC_MODE_DEEP 6
+
+#define AT91_SDRAMC_TR (AT91_SDRAMC + 0x04) /* SDRAM
Controller Refresh Timer Register */
+#define AT91_SDRAMC_COUNT (0xfff << 0) /* Refresh
Timer Counter */
+
+#define AT91_SDRAMC_CR (AT91_SDRAMC + 0x08) /* SDRAM
Controller Configuration Register */
+#define AT91_SDRAMC_NC (3 << 0) /* Number of
Column Bits */
+#define AT91_SDRAMC_NC_8 (0 << 0)
+#define AT91_SDRAMC_NC_9 (1 << 0)
+#define AT91_SDRAMC_NC_10 (2 << 0)
+#define AT91_SDRAMC_NC_11 (3 << 0)
+#define AT91_SDRAMC_NR (3 << 2) /* Number of Row
Bits */
+#define AT91_SDRAMC_NR_11 (0 << 2)
+#define AT91_SDRAMC_NR_12 (1 << 2)
+#define AT91_SDRAMC_NR_13 (2 << 2)
+#define AT91_SDRAMC_NB (1 << 4) /* Number of Banks */
+#define AT91_SDRAMC_NB_2 (0 << 4)
+#define AT91_SDRAMC_NB_4 (1 << 4)
+#define AT91_SDRAMC_CAS (3 << 5) /* CAS Latency */
+#define AT91_SDRAMC_CAS_1 (1 << 5)
+#define AT91_SDRAMC_CAS_2 (2 << 5)
+#define AT91_SDRAMC_CAS_3 (3 << 5)
+#define AT91_SDRAMC_DBW (1 << 7) /* Data Bus Width */
+#define AT91_SDRAMC_DBW_32 (0 << 7)
+#define AT91_SDRAMC_DBW_16 (1 << 7)
+#define AT91_SDRAMC_TWR (0xf << 8) /* Write
Recovery Delay */
+#define AT91_SDRAMC_TRC (0xf << 12) /* Row Cycle
Delay */
+#define AT91_SDRAMC_TRP (0xf << 16) /* Row
Precharge Delay */
+#define AT91_SDRAMC_TRCD (0xf << 20) /* Row to Column
Delay */
+#define AT91_SDRAMC_TRAS (0xf << 24) /* Active to
Precharge Delay */
+#define AT91_SDRAMC_TXSR (0xf << 28) /* Exit Self
Refresh to Active Delay */
+
+#define AT91_SDRAMC_LPR (AT91_SDRAMC + 0x10) /* SDRAM
Controller Low Power Register */
+#define AT91_SDRAMC_LPCB (3 << 0) /* Low-power
Configurations */
+#define AT91_SDRAMC_LPCB_DISABLE 0
+#define AT91_SDRAMC_LPCB_SELF_REFRESH 1
+#define AT91_SDRAMC_LPCB_POWER_DOWN 2
+#define AT91_SDRAMC_LPCB_DEEP_POWER_DOWN 3
+#define AT91_SDRAMC_PASR (7 << 4) /* Partial Array
Self Refresh */
+#define AT91_SDRAMC_TCSR (3 << 8) /* Temperature
Compensated Self Refresh */
+#define AT91_SDRAMC_DS (3 << 10) /* Drive Strength */
+#define AT91_SDRAMC_TIMEOUT (3 << 12) /* Time to
define when Low Power Mode is enabled */
+#define AT91_SDRAMC_TIMEOUT_0_CLK_CYCLES (0 << 12)
+#define AT91_SDRAMC_TIMEOUT_64_CLK_CYCLES (1 << 12)
+#define AT91_SDRAMC_TIMEOUT_128_CLK_CYCLES (2 << 12)
+
+#define AT91_SDRAMC_IER (AT91_SDRAMC + 0x14) /* SDRAM
Controller Interrupt Enable Register */
+#define AT91_SDRAMC_IDR (AT91_SDRAMC + 0x18) /* SDRAM
Controller Interrupt Disable Register */
+#define AT91_SDRAMC_IMR (AT91_SDRAMC + 0x1C) /* SDRAM
Controller Interrupt Mask Register */
+#define AT91_SDRAMC_ISR (AT91_SDRAMC + 0x20) /* SDRAM
Controller Interrupt Status Register */
+#define AT91_SDRAMC_RES (1 << 0) /* Refresh Error
Status */
+
+#define AT91_SDRAMC_MDR (AT91_SDRAMC + 0x24) /* SDRAM Memory
Device Register */
+#define AT91_SDRAMC_MD (3 << 0) /* Memory Device
Type */
+#define AT91_SDRAMC_MD_SDRAM 0
+#define AT91_SDRAMC_MD_LOW_POWER_SDRAM 1
+
+
+#endif
diff --git a/include/asm-arm/arch-at91/hardware.h
b/include/asm-arm/arch-at91/hardware.h
index 82b4b23..756a242 100644
--- a/include/asm-arm/arch-at91/hardware.h
+++ b/include/asm-arm/arch-at91/hardware.h
@@ -53,6 +53,23 @@
#error "Unsupported AT91 processor"
#endif
+/* External Memory Map */
+#define AT91_CHIPSELECT_0 0x10000000
+#define AT91_CHIPSELECT_1 0x20000000
+#define AT91_CHIPSELECT_2 0x30000000
+#define AT91_CHIPSELECT_3 0x40000000
+#define AT91_CHIPSELECT_4 0x50000000
+#define AT91_CHIPSELECT_5 0x60000000
+#define AT91_CHIPSELECT_6 0x70000000
+#define AT91_CHIPSELECT_7 0x80000000
+
+/* SDRAM */
+#ifdef CONFIG_DRAM_BASE
+#define AT91_SDRAM_BASE CONFIG_DRAM_BASE
+#else
+#define AT91_SDRAM_BASE AT91_CHIPSELECT_1
+#endif
+
/* Clocks */
#define AT91_SLOW_CLOCK 32768 /* slow clock */
diff --git a/include/configs/pm9263.h b/include/configs/pm9263.h
new file mode 100644
index 0000000..9ae737f
--- /dev/null
+++ b/include/configs/pm9263.h
@@ -0,0 +1,367 @@
+/*
+ * (C) Copyright 2007-2008
+ * Stelian Pop <stelian.pop@leadtechdesign.com>
+ * Lead Tech Design <www.leadtechdesign.com>
+ * Ilko Iliev <www.ronetix.at>
+ *
+ * Configuation settings for the RONETIX PM9263 board.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/* ARM asynchronous clock */
+#define AT91_CPU_NAME "AT91SAM9263"
+
+#define CONFIG_DISPLAY_BOARDINFO
+
+#define MASTER_PLL_DIV 15
+#define MASTER_PLL_MUL 162
+#define MAIN_PLL_DIV 2 /* 2 or 4 */
+#define AT91_MAIN_CLOCK 18432000
+
+#define CONFIG_SYS_HZ 1000000
+
+#define CONFIG_ARM926EJS 1 /* This is an ARM926EJS Core */
+#define CONFIG_AT91SAM9263 1 /* It's an Atmel AT91SAM9263 SoC*/
+#define CONFIG_PM9263 1 /* on a Ronetix PM9263 Board */
+#define CONFIG_ARCH_CPU_INIT
+#undef CONFIG_USE_IRQ /* we don't need IRQ/FIQ stuff */
+
+/* clocks */
+#define CONFIG_SYS_MOR_VAL 0x00002001 /* CKGR_MOR - enable main
osc. */
+#define CONFIG_SYS_PLLAR_VAL \
+ (0x2000BF00 | ((MASTER_PLL_MUL - 1) << 16) | (MASTER_PLL_DIV))
+
+#if (MAIN_PLL_DIV == 2)
+/* PCK/2 = MCK Master Clock from PLLA */
+#define CONFIG_SYS_MCKR1_VAL 0x00000100
+/* PCK/2 = MCK Master Clock from PLLA */
+#define CONFIG_SYS_MCKR2_VAL 0x00000102
+#else
+/* PCK/4 = MCK Master Clock from PLLA */
+#define CONFIG_SYS_MCKR1_VAL 0x00000200
+/* PCK/4 = MCK Master Clock from PLLA */
+#define CONFIG_SYS_MCKR2_VAL 0x00000202
+#endif
+/* define PDC[31:16] as DATA[31:16] */
+#define CONFIG_SYS_PIOD_PDR_VAL1 0xFFFF0000
+/* no pull-up for D[31:16] */
+#define CONFIG_SYS_PIOD_PPUDR_VAL 0xFFFF0000
+/* EBI0_CSA, CS1 SDRAM, CS3 NAND Flash, 3.3V memories */
+#define CONFIG_SYS_MATRIX_EBI0CSA_VAL 0x0001010A
+/* EBI1_CSA, 3.3v, no pull-ups */
+#define CONFIG_SYS_MATRIX_EBI1CSA_VAL 0x00010100
+
+/* SDRAM */
+/* SDRAMC_MR Mode register */
+#define CONFIG_SYS_SDRC_MR_VAL1 0
+/* SDRAMC_TR - Refresh Timer register */
+#define CONFIG_SYS_SDRC_TR_VAL1 0x13C
+#define CONFIG_SYS_SDRC_CR_VAL 0x85227279 /*CL3*/
+/* Memory Device Register -> SDRAM */
+#define CONFIG_SYS_SDRC_MDR_VAL 0
+#define CONFIG_SYS_SDRC_MR_VAL2 0x00000002 /* SDRAMC_MR */
+#define CONFIG_SYS_SDRAM_VAL1 0 /* SDRAM_BASE */
+#define CONFIG_SYS_SDRC_MR_VAL3 4 /* SDRC_MR */
+#define CONFIG_SYS_SDRAM_VAL2 0 /* SDRAM_BASE */
+#define CONFIG_SYS_SDRAM_VAL3 0 /* SDRAM_BASE */
+#define CONFIG_SYS_SDRAM_VAL4 0 /* SDRAM_BASE */
+#define CONFIG_SYS_SDRAM_VAL5 0 /* SDRAM_BASE */
+#define CONFIG_SYS_SDRAM_VAL6 0 /* SDRAM_BASE */
+#define CONFIG_SYS_SDRAM_VAL7 0 /* SDRAM_BASE */
+#define CONFIG_SYS_SDRAM_VAL8 0 /* SDRAM_BASE */
+#define CONFIG_SYS_SDRAM_VAL9 0 /* SDRAM_BASE */
+#define CONFIG_SYS_SDRC_MR_VAL4 3 /* SDRC_MR */
+#define CONFIG_SYS_SDRAM_VAL10 0 /* SDRAM_BASE */
+#define CONFIG_SYS_SDRC_MR_VAL5 0 /* SDRC_MR */
+#define CONFIG_SYS_SDRAM_VAL11 0 /* SDRAM_BASE */
+#define CONFIG_SYS_SDRC_TR_VAL2 1200 /* SDRAM_TR */
+#define CONFIG_SYS_SDRAM_VAL12 0 /* SDRAM_BASE */
+
+/* setup SMC0, CS0 (NOR Flash) - 16-bit, 15 WS */
+#define CONFIG_SYS_SMC0_SETUP0_VAL 0x0A0A0A0A /* SMC_SETUP */
+#define CONFIG_SYS_SMC0_PULSE0_VAL 0x0B0B0B0B /* SMC_PULSE */
+#define CONFIG_SYS_SMC0_CYCLE0_VAL 0x00160016 /* SMC_CYCLE */
+#define CONFIG_SYS_SMC0_CTRL0_VAL 0x00161003 /* SMC_MODE */
+
+/* setup SMC1, CS0 (PSRAM) - 16-bit */
+#define CONFIG_SYS_SMC1_SETUP0_VAL 0x00000000 /* SMC_SETUP */
+#define CONFIG_SYS_SMC1_PULSE0_VAL 0x07020707 /* SMC_PULSE */
+#define CONFIG_SYS_SMC1_CYCLE0_VAL 0x00080008 /* SMC_CYCLE */
+#define CONFIG_SYS_SMC1_CTRL0_VAL 0x31001000 /* SMC_MODE */
+
+#define CONFIG_SYS_RSTC_RMR_VAL 0xA5000301 /* user reset
enable */
+
+/* Watchdog */
+#define CONFIG_SYS_WDTC_WDMR_VAL 0x3fff8fff /* disable watchdog */
+
+/* */
+
+#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */
+#define CONFIG_SETUP_MEMORY_TAGS 1
+#define CONFIG_INITRD_TAG 1
+
+#undef CONFIG_SKIP_LOWLEVEL_INIT
+#undef CONFIG_SKIP_RELOCATE_UBOOT
+#define CONFIG_USER_LOWLEVEL_INIT 1
+
+/*
+ * Hardware drivers
+ */
+#define CONFIG_ATMEL_USART 1
+#undef CONFIG_USART0
+#undef CONFIG_USART1
+#undef CONFIG_USART2
+#define CONFIG_USART3 1 /* USART 3 is DBGU */
+
+/* LCD */
+#define CONFIG_LCD 1
+#define LCD_BPP LCD_COLOR8
+#define CONFIG_LCD_LOGO 1
+#undef LCD_TEST_PATTERN
+#define CONFIG_LCD_INFO 1
+#define CONFIG_LCD_INFO_BELOW_LOGO 1
+#define CONFIG_SYS_WHITE_ON_BLACK 1
+#define CONFIG_ATMEL_LCD 1
+#define CONFIG_ATMEL_LCD_BGR555 1
+#define CONFIG_SYS_CONSOLE_IS_IN_ENV 1
+
+#define CONFIG_LCD_IN_PSRAM 1
+
+/* LED */
+#define CONFIG_AT91_LED
+#define CONFIG_RED_LED AT91_PIN_PB7 /* this is the power
led */
+#define CONFIG_GREEN_LED AT91_PIN_PB8 /* this is the user1 led */
+
+#define CONFIG_BOOTDELAY 3
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE 1
+#define CONFIG_BOOTP_BOOTPATH 1
+#define CONFIG_BOOTP_GATEWAY 1
+#define CONFIG_BOOTP_HOSTNAME 1
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+#undef CONFIG_CMD_BDI
+#undef CONFIG_CMD_IMI
+#undef CONFIG_CMD_AUTOSCRIPT
+#undef CONFIG_CMD_FPGA
+#undef CONFIG_CMD_LOADS
+#undef CONFIG_CMD_IMLS
+
+#define CONFIG_CMD_PING 1
+#define CONFIG_CMD_DHCP 1
+#define CONFIG_CMD_NAND 1
+#define CONFIG_CMD_USB 1
+
+/* SDRAM */
+#define CONFIG_NR_DRAM_BANKS 1
+#define PHYS_SDRAM 0x20000000
+#define PHYS_SDRAM_SIZE 0x04000000 /* 64 megs */
+
+/* DataFlash */
+#define CONFIG_ATMEL_DATAFLASH_SPI
+#define CONFIG_HAS_DATAFLASH 1
+#define CONFIG_SYS_SPI_WRITE_TOUT (5 * CONFIG_SYS_HZ)
+#define CONFIG_SYS_MAX_DATAFLASH_BANKS 1
+#define CONFIG_SYS_DATAFLASH_LOGIC_ADDR_CS0 0xC0000000 /* CS0 */
+#define AT91_SPI_CLK 15000000
+#define DATAFLASH_TCSS (0x1a << 16)
+#define DATAFLASH_TCHS (0x1 << 24)
+
+/* NOR flash, if populated */
+#define CONFIG_SYS_FLASH_CFI 1
+#define CONFIG_FLASH_CFI_DRIVER 1
+#define PHYS_FLASH_1 0x10000000
+#define CONFIG_SYS_FLASH_BASE PHYS_FLASH_1
+#define CONFIG_SYS_MAX_FLASH_SECT 256
+#define CONFIG_SYS_MAX_FLASH_BANKS 1
+
+/* NAND flash */
+#ifdef CONFIG_CMD_NAND
+#define CONFIG_NAND_ATMEL
+#define CONFIG_SYS_NAND_MAX_CHIPS 1
+#define CONFIG_SYS_MAX_NAND_DEVICE 1
+#define CONFIG_SYS_NAND_BASE 0x40000000
+#define CONFIG_SYS_NAND_DBW_8 1
+/* our ALE is AD21 */
+#define CONFIG_SYS_NAND_MASK_ALE (1 << 21)
+/* our CLE is AD22 */
+#define CONFIG_SYS_NAND_MASK_CLE (1 << 22)
+#define CONFIG_SYS_NAND_ENABLE_PIN AT91_PIN_PD15
+#define CONFIG_SYS_NAND_READY_PIN AT91_PIN_PB30
+#endif
+
+#define CONFIG_CMD_JFFS2 1
+#define CONFIG_JFFS2_CMDLINE 1
+#define CONFIG_JFFS2_NAND 1
+#define CONFIG_JFFS2_DEV "nand0" /* NAND device jffs2 lives on */
+#define CONFIG_JFFS2_PART_OFFSET 0 /* start of jffs2 partition */
+#define CONFIG_JFFS2_PART_SIZE (256 * 1024 * 1024) /* partition
size*/
+
+/* PSRAM */
+#define PHYS_PSRAM 0x70000000
+#define PHYS_PSRAM_SIZE 0x00400000 /* 4MB */
+
+/* Ethernet */
+#define CONFIG_MACB 1
+#define CONFIG_RMII 1
+#define CONFIG_NET_MULTI 1
+#define CONFIG_NET_RETRY_COUNT 20
+#define CONFIG_RESET_PHY_R 1
+
+/* USB */
+#define CONFIG_USB_ATMEL
+#define CONFIG_USB_OHCI_NEW 1
+#define CONFIG_DOS_PARTITION 1
+#define CONFIG_SYS_USB_OHCI_CPU_INIT 1
+#define CONFIG_SYS_USB_OHCI_REGS_BASE 0x00a00000 /*
AT91SAM9263_UHP_BASE */
+#define CONFIG_SYS_USB_OHCI_SLOT_NAME "at91sam9263"
+#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 2
+#define CONFIG_USB_STORAGE 1
+
+#define CONFIG_SYS_LOAD_ADDR 0x22000000 /* load address */
+
+#define CONFIG_SYS_MEMTEST_START PHYS_SDRAM
+#define CONFIG_SYS_MEMTEST_END 0x23e00000
+
+#define CONFIG_SYS_USE_FLASH 1
+#undef CONFIG_SYS_USE_DATAFLASH
+#undef CONFIG_SYS_USE_NANDFLASH
+
+#ifdef CONFIG_SYS_USE_DATAFLASH
+
+/* bootstrap + u-boot + env + linux in dataflash on CS0 */
+#define CONFIG_ENV_IS_IN_DATAFLASH
+#define CFG_MONITOR_BASE (CFG_DATAFLASH_LOGIC_ADDR_CS0 + 0x8400)
+#define CONFIG_ENV_OFFSET 0x4200
+#define CONFIG_ENV_ADDR (CFG_DATAFLASH_LOGIC_ADDR_CS0 +
CONFIG_ENV_OFFSET)
+#define CONFIG_ENV_SIZE 0x4200
+#define CONFIG_BOOTCOMMAND "cp.b 0xC0042000 0x22000000 0x210000; bootm"
+#define CONFIG_BOOTARGS "console=ttyS0,115200 " \
+ "root=/dev/mtdblock0 " \
+ "mtdparts=at91_nand:-(root) "\
+ "rw rootfstype=jffs2"
+
+#elif defined(CONFIG_SYS_USE_NANDFLASH) /* CFG_USE_NANDFLASH */
+
+/* bootstrap + u-boot + env + linux in nandflash */
+#define CONFIG_ENV_IS_IN_NAND
+#define CONFIG_ENV_OFFSET 0x60000
+#define CONFIG_ENV_OFFSET_REDUND 0x80000
+#define CONFIG_ENV_SIZE 0x20000 /* 1 sector = 128 kB */
+#define CONFIG_BOOTCOMMAND "nand read 0x22000000 0xA0000 0x200000;
bootm"
+#define CONFIG_BOOTARGS "console=ttyS0,115200 " \
+ "root=/dev/mtdblock5 " \
+ "mtdparts=at91_nand:" \
+ "128k(bootstrap)ro," \
+ "256k(uboot)ro," \
+ "128k(env1)ro," \
+ "128k(env2)ro," \
+ "2M(linux)," \
+ "-(root) " \
+ "rw rootfstype=jffs2"
+
+#elif defined(CONFIG_SYS_USE_FLASH) /* CFG_USE_FLASH */
+
+#define CONFIG_ENV_IS_IN_FLASH 1
+#define CONFIG_ENV_OFFSET 0x40000
+#define CONFIG_ENV_SECT_SIZE 0x10000
+#define CONFIG_ENV_SIZE 0x10000
+#define CONFIG_ENV_OVERWRITE 1
+
+/* JFFS Partition offset set */
+#define CONFIG_SYS_JFFS2_FIRST_BANK 0
+#define CONFIG_SYS_JFFS2_NUM_BANKS 1
+
+/* 512k reserved for u-boot */
+#define CONFIG_SYS_JFFS2_FIRST_SECTOR 11
+
+#define CONFIG_BOOTCOMMAND "run flashboot"
+#define CONFIG_ROOTPATH /ronetix/rootfs
+#define CONFIG_AUTOBOOT_PROMPT "autoboot in %d seconds\n"
+
+#define CONFIG_CON_ROT "fbcon=rotate:3 "
+#define CONFIG_BOOTARGS "root=/dev/mtdblock4 rootfstype=jffs2 "\
+ CONFIG_CON_ROT
+
+#define MTDIDS_DEFAULT "nor0=physmap-flash.0,nand0=nand"
+#define MTDPARTS_DEFAULT \
+ "mtdparts=physmap-flash.0:" \
+ "256k(u-boot)ro," \
+ "64k(u-boot-env)ro," \
+ "1408k(kernel)," \
+ "-(rootfs);" \
+ "nand:-(nand)"
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "mtdids=" MTDIDS_DEFAULT "\0" \
+ "mtdparts=" MTDPARTS_DEFAULT "\0" \
+ "partition=nand0,0\0" \
+ "ramargs=setenv bootargs $(bootargs) $(mtdparts)\0" \
+ "nfsargs=setenv bootargs root=/dev/nfs rw " \
+ CONFIG_CON_ROT \
+ "nfsroot=$(serverip):$(rootpath) $(mtdparts)\0" \
+ "addip=setenv bootargs $(bootargs) " \
+ "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask)"\
+ ":$(hostname):eth0:off\0" \
+ "ramboot=tftpboot 0x22000000 vmImage;" \
+ "run ramargs;run addip;bootm 22000000\0" \
+ "nfsboot=tftpboot 0x22000000 vmImage;" \
+ "run nfsargs;run addip;bootm 22000000\0" \
+ "flashboot=run ramargs;run addip;bootm 0x10050000\0" \
+ ""
+
+#else
+#error "Undefined memory device"
+#endif
+
+#define CONFIG_BAUDRATE 115200
+#define CONFIG_SYS_BAUDRATE_TABLE {115200 , 19200, 38400, 57600, 9600 }
+
+#define CONFIG_SYS_PROMPT "u-boot-pm9263> "
+#define CONFIG_SYS_CBSIZE 256
+#define CONFIG_SYS_MAXARGS 16
+#define CONFIG_SYS_PBSIZE \
+ (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
+#define CONFIG_SYS_LONGHELP 1
+#define CONFIG_CMDLINE_EDITING 1
+
+#define ROUND(A, B) (((A) + (B)) & ~((B) - 1))
+/*
+ * Size of malloc() pool
+ */
+#define CONFIG_SYS_MALLOC_LEN ROUND(3 * CONFIG_ENV_SIZE + 128 *
1024, 0x1000)
+#define CONFIG_SYS_GBL_DATA_SIZE 128 /* 128 bytes for initial data */
+
+#define CONFIG_STACKSIZE (32 * 1024) /* regular stack */
+
+#ifdef CONFIG_USE_IRQ
+#error CONFIG_USE_IRQ not supported
+#endif
+
+#endif
diff --git a/tools/Makefile b/tools/Makefile
index 9e9ee15..fbc64ba 100644
--- a/tools/Makefile
+++ b/tools/Makefile
@@ -47,6 +47,9 @@ endif
ifeq ($(VENDOR),atmel)
LOGO_BMP= logos/atmel.bmp
endif
+ifeq ($(VENDOR),ronetix)
+LOGO_BMP= logos/ronetix.bmp
+endif
#-------------------------------------------------------------------------
diff --git a/tools/logos/ronetix.bmp b/tools/logos/ronetix.bmp
new file mode 100644
index
0000000000000000000000000000000000000000..f956813915c7822ba11a3ab81ad9f48fa2849a5c
GIT binary patch
literal 5638
zcmd6qPgoO26u>9!GQ+G%SPCLU3BjO7DVS2!)VBPyv;owl)Y#NEim_WTHkD<1;K-39
z#~e9w<jB#ZM~*q>m?KAyee-X3!v|>l=~v&!<IT>_y!q{$nKzT!2e=mr!EFeoptJ*;
z01crI_z%(p&tp>mhDWYa;C)92{Mo3(=GupBu6<k+sE=zRff7PfD3MB`R4R>9=`>2G
zGbo+Opp4LIl$oAJ(?YXoI-5mVp?UCgfU@~K$_p)mzXQ-Z$`^~^w~mTni^XN|4dvx!
zv<#X`*TJr$<<(UfqmEX=W`tdXao~Av4XuGrXX{`$U@Wj3VDojf0d`|!6K!m6!Wa#-
z3AQNg7TVm}LR&(&!Dj<)ZEvG((ABjD_-R17hPG=p=-)s!u(jF_s_pEc9ih9>w~2Ok
zchRoUJ+!;GhxR~gwI<kow7<{w4ZLrn{WoCun&=JKJ#OE=MQ=g(_Yc7yKt0%l19Tv?
z4t0m9Ua!M5w+&QpfYuLD18k$&1bc*<+%~xdJv>B*LXXhV(GmKFecD3DKW)CSnf{~!
zBg8l!!D`vjQg$o3*_l?ET`0j9J)fMJnal at 1Z4oNCOcq#mc1o7j|EZaZXgJTSMW>2r
zF*WC?mXqaxC-x|(WTDI=l$tk#FWHN38kTYnrx&8wI4+oux-1(qjL;>&<CJcNMwvtO
zgR-IiDztQ?ZSWkr2*r{q-Vo<55`|DVZ=fWNm9!14aK2VR=QEQiF;dSW7~UTjVl1*n
zc!87JB`Xl3TAAa_3F`;l)3^>T-EQs-Uxs4I;w?ycg<Up88$U*F%9Oo{G2$}8M@<Nb
z5~s)1PR$WECwuD}ZO!B{zH-$24xf+cIADT}+b8ll>{YMqiL(-*l2GFlJjrW#{3tc<
zD!kQh56>87Y(nzsfPxjx@%dIhw@>sUb{Hl@$Ir5Z63w3!KZl1>0OGJ%f-Ai$BACt#
zB*|x9m3&UGhlk;d*|;3{&XSfNZBB^0Tlq$1vuL`*=fmAqHy~?kr|_{HfnJohUw|c8
z(&538B}t_C`1)WFY(1aE<amk?tG2vGOvf?4dHGSs_#|}K at xwj5c~DMRe-J;$Zp%T9
z3@df2@R&Bw5nO_N6**1tF>3NPUrx4#|L%FQ##`c75R0ASh;tL%|9d`HEjeqVQ>|j7
zUw|Lut6ub?ho>ZwoL_t<U&WSQ%`8hm$>R&muXJ`={Md@(YL}~<nn^#~`0=Y=^6}JW
zdY|~Ym*kwlZf64lK5BI;iP|p&;HiA<iQFT68N%GPPk7lRFu(4A#=}J8y$@eTb~Ah6
zn=c0WsNVIM%G2R=J~k)O1fI+*GUOiLsGC$vlXlqtc6j&v&SSCraO4?yY~|Bq66>9O
zY(`Bj#nyese*InJsr`XRZtCb+7iJ$VEj at lAVth7V`xREA!Z9J at oBlIjp;PhUNP(??
z7aRIT142dxA-1KzmWKJnP|F^L2|Jt59I1*U3pT~K!k^~j8=BaK$5IMKxt at aaD?W>a
z)izzw>(A&Zv%kKM4aTqO2&&De!|PEJ+y)E&9ekN78FfP)#ENg7=NUL-j!A&e3G+R#
z`DU;h-srEemtVw&hK6Eef6CrZL`zCcUsPj4OPbGLkS+PyynBHU1ILNHKk4<y+yV0h
zJ|=<<XE(?KU$&CZO=~>!dX+7I&hY^7t91#O=Wj{Zh$mOY5eCCTLX+_$m+xq~9p&`u
z{Gds(I*6r{y^0 at WD>f$fLw$`?c2O)c+?&hYcf_F~_^Mab#w2)xv8RI)Z)h;~gXCkg
zJSo6jdg3TRW0tAp5x4{Lcv0Lh&R<I|Uc9KgdVH(|)8buUbV2lm-q?hIr%Vw)r(fY=
zG6!z{xE2 at T8v?+el-p5*n)3Wr75o?g0lu70I?A;&#)ROLPl5Zl&&P6l(pr0J2T4}#
z!6aNQ+ZxZ3ht%@028<6ql{|3%oyO-T+ptcvp2bGA%;pXCZ1(%vz8|i(hWb4-<6U#T
zj)4MP2H?&ZnbRk(+4)!n=jZsKieUW4OIcUx3Y`)^R{f^Wj<!l?&j{q(MfD@V>hg|q
z#u8Q}Lhq=7uG4d;i$!v53DTIHDQb4hBanA}5YvFMFJDVvW$TJ^DhxkHL12El1TJx^
zC~7NGR{W!!v1+CA>Xi<sTRuyk!)ImHO`aMFl>o$m(`t*rCcY;s7<-sf1#TRb%oShY
z&4(`XJPFCeOzCeD1H8Va0S99b)R0Tbl$NB<FCU+e=SjG0>K_;S^IzW3dt~sMt{VyI
z1g&pj)STBZKbnO+Df3F}2;L_4`P`JgAn=fLA?jMx+VulJm8casoIK}x6A#|-s;d4^
zBSD7)dChC|;S2e~i9XdP4)8IjOC7u-dgso6-?C^=^zsoa?}<GU9}5iOJn`i>=YOSR
NZ2eYzcz8HI_77a#1d{*&
literal 0
HcmV?d00001
--
1.6.1.3
--
With best regards,
Ilko Iliev
Ronetix Development Tools GmbH
CPU Modules, JTAG/BDM Emulators and Flash Programmers
Waidhausenstrasse 13/5, 1140 Vienna, Austria
E-Mail: iliev at ronetix.at; Web: www.ronetix.at
reply other threads:[~2009-03-31 14:16 UTC|newest]
Thread overview: [no followups] expand[flat|nested] mbox.gz Atom feed
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=49D225CE.1080203@ronetix.at \
--to=iliev@ronetix.at \
--cc=u-boot@lists.denx.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.