From: Michael Cree <mcree@orcon.net.nz>
To: linux-alpha@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Subject: Kernel 2.6.30.1 Oops on Alpha Architecture when starting Xserver
Date: Wed, 15 Jul 2009 22:41:07 +1200 [thread overview]
Message-ID: <4A5DB243.2000100@orcon.net.nz> (raw)
Kernel Oops on Alpha Architecture when starting the Xserver.
Whenever I start the Xserver, version 1.6.2 from Debain Unstable, I get a
kernel oops report and the computer crashes hard; no ping response, hitting
the reset button to return to SRM fails. Has caused corruption on disc
partitions on some crashes. This occurs with kernels 2.6.30, 2.6.30.1 and
also a patched version of 2.6.29.x (patched so that I get PCI resource files
under sysfs).
The kernel oops is:
Unable to handle kernel paging request at virtual address 000000000000000c
Xorg(1940): Oops 0
pc = [<fffffc000031e634>] ra = [<fffffc000031570c>] ps = 0007 Not
tainted
pc is at cia_machine_check+0x84/0x570
ra is at do_entInt+0x16c/0x1d0
v0 = 0000000000000001 t0 = 0000000000000001 t1 = fffffc000071a250
t2 = 0000000000000001 t3 = 0000000000000031 t4 = 3a00000000000000
t5 = 0000000000000004 t6 = 000000000000000f t7 = fffffc0021c0c000
s0 = fffffc00006ed2d8 s1 = 0000000000000000 s2 = fffffc0021c0fee8
s3 = 000000011ff016fc s4 = 000000011ff016f4 s5 = fffffc0000006068
s6 = 0000000000000660
a0 = 0000000000000001 a1 = 0000000000000000 a2 = fffffc0000006068
a3 = 0000000000000000 a4 = 0000000100000010 a5 = 000000012029c0a0
t8 = 0000000000000010 t9 = 00000001200c0b98 t10= 0000000000000000
t11= 000000000000000a pv = fffffc000031e5b0 at = 0000000000000006
gp = fffffc00007192f0 sp = fffffc0021c0fe88
Disabling lock debugging due to kernel taint
Trace:
[<fffffc000031570c>] do_entInt+0x16c/0x1d0
[<fffffc0000310c80>] ret_from_sys_call+0x0/0x10
[<fffffc0000310720>] entInt+0x0/0x80
Code: 207f0660 41e305a3 2a620000 426015a1 44230001 e420000f
<a031000c> 47ff0413
On one crash there was a trace of the Xorg.log file left intact ending with
the following lines:
(II) RADEON(0): Attempting to read un-POSTed bios
(II) RADEON(0): ATOM BIOS detected
(II) RADEON(0): ATOM BIOS Rom:
SubsystemVendorID: 0x2232 SubsystemID: 0x1787
IOBaseAddress: 0x0000
Filename: 72319EAA.QEA
BIOS Bootup Message: HD2400 GDDR2_32MX16 64BIT 256MB
72319EAA.QEA
(II) RADEON(0): Framebuffer space used by Firmware (kb): 0
(WW) RADEON(0): rhdAtomGetFbBaseAndSize: AtomBIOS specified VRAM scratch
space size invalid
(II) RADEON(0): default to: 20480
(II) RADEON(0): Cannot get VRAM scratch space. Allocating in main memory
instead
(II) RADEON(0): Default Engine Clock: 525000
(II) RADEON(0): Default Memory Clock: 400000
(II) RADEON(0): Maximum Pixel ClockPLL Frequency Output: 1200000
(II) RADEON(0): Minimum Pixel ClockPLL Frequency Output: 0
(II) RADEON(0): Maximum Pixel ClockPLL Frequency Input: 13500
(II) RADEON(0): Minimum Pixel ClockPLL Frequency Input: 1000
(II) RADEON(0): Maximum Pixel Clock: 400000
(II) RADEON(0): Reference Clock: 27000
(II) RADEON(0): Default Engine Clock: 525000
(II) RADEON(0): Default Memory Clock: 400000
(II) RADEON(0): Calling ASIC Init
[Xorg.log ends here]
Other machine info follows:
aleph:~# cat /proc/version
Linux version 2.6.30.1-miata (mjc@alpha) (gcc version 4.2.4 (Debian
4.2.4-6)) #1 Fri Jul 3 22:54:36 NZST 2009
aleph:~# cat /proc/cpuinfo
cpu : Alpha
cpu model : EV56
cpu variation : 7
cpu revision : 0
cpu serial number :
system type : Miata
system variation : 0
system revision : 0
system serial number :
cycle frequency [Hz] : 600000000
timer frequency [Hz] : 1024.00
page size [bytes] : 8192
phys. address bits : 40
max. addr. space # : 127
BogoMIPS : 1187.96
kernel unaligned acc : 0 (pc=0,va=0)
user unaligned acc : 0 (pc=0,va=0)
platform string : Digital Personal WorkStation 600au
cpus detected : 1
L1 Icache : 8K, 1-way, 32b line
L1 Dcache : 8K, 1-way, 32b line
L2 cache : 96K, 3-way, 64b line
L3 cache : 2048K, 1-way, 64b line
aleph:~# cat /proc/modules
ipv6 331224 22 - Live 0xfffffffc008c2000
loop 18872 0 - Live 0xfffffffc00812000
snd_es18xx 40484 0 - Live 0xfffffffc007f0000
ohci_hcd 26048 0 - Live 0xfffffffc00788000
ehci_hcd 40004 0 - Live 0xfffffffc00764000
ide_cd_mod 36336 0 - Live 0xfffffffc0073c000
cdrom 44000 1 ide_cd_mod, Live 0xfffffffc006fc000
snd_hda_codec_atihdmi 4616 1 - Live 0xfffffffc006d8000
snd_hda_intel 31184 0 - Live 0xfffffffc006be000
snd_cmipci 42152 0 - Live 0xfffffffc00696000
snd_opl3_lib 13288 2 snd_es18xx,snd_cmipci, Live 0xfffffffc00672000
snd_hwdep 9760 1 snd_opl3_lib, Live 0xfffffffc0065a000
snd_mpu401_uart 9488 2 snd_es18xx,snd_cmipci, Live 0xfffffffc00642000
snd_seq_midi 8768 0 - Live 0xfffffffc0062a000
snd_seq_midi_event 8032 1 snd_seq_midi, Live 0xfffffffc00614000
sata_sil 11328 0 - Live 0xfffffffc005fe000
snd_hda_codec 72498 2 snd_hda_codec_atihdmi,snd_hda_intel, Live
0xfffffffc005de000
snd_rawmidi 26657 2 snd_mpu401_uart,snd_seq_midi, Live 0xfffffffc005a6000
snd_pcm 77689 4 snd_es18xx,snd_hda_intel,snd_cmipci,snd_hda_codec, Live
0xfffffffc00576000
snd_seq 67568 2 snd_seq_midi,snd_seq_midi_event, Live 0xfffffffc00534000
snd_timer 25064 3 snd_opl3_lib,snd_pcm,snd_seq, Live 0xfffffffc004fe000
snd_seq_device 8808 4 snd_opl3_lib,snd_seq_midi,snd_rawmidi,snd_seq,
Live 0xfffffffc004de000
snd 72216 12
snd_es18xx,snd_hda_intel,snd_cmipci,snd_opl3_lib,snd_hwdep,snd_mpu401_uart,snd_hda_codec,snd_rawmidi,snd_pcm,snd_seq,snd_timer,snd_seq_device,
Live 0xfffffffc004b8000
snd_page_alloc 11200 2 snd_hda_intel,snd_pcm, Live 0xfffffffc00484000
soundcore 7712 1 snd, Live 0xfffffffc0046e000
libata 191292 1 sata_sil, Live 0xfffffffc0042a000
evdev 12896 1 - Live 0xfffffffc003b6000
pcspkr 3088 0 - Live 0xfffffffc0039e000
usbcore 168612 3 ohci_hcd,ehci_hcd, Live 0xfffffffc00364000
cy82c693 4552 0 - Live 0xfffffffc002f0000
tulip 56856 0 - Live 0xfffffffc002d0000
ide_pci_generic 5132 0 - Live 0xfffffffc002a6000
aleph:~# cat /proc/ioports
0000-001f : dma1
0020-003f : pic1
0040-005f : timer
0060-006f : keyboard
0070-0080 : rtc
00a0-00bf : pic2
00c0-00df : dma2
0170-0177 : 0000:00:07.2
0170-0177 : cy82c693
01f0-01f7 : 0000:00:07.1
01f0-01f7 : cy82c693
0220-022f : ES18xx
02f8-02ff : serial
0330-0331 : MPU401 UART
0376-0376 : 0000:00:07.2
0376-0376 : cy82c693
03c0-03df : vga+
03f2-03f2 : floppy
03f4-03f5 : floppy
03f6-03f6 : 0000:00:07.1
03f6-03f6 : cy82c693
03f7-03f7 : floppy
03f8-03ff : serial
8000-8fff : PCI Bus 0000:01
8000-80ff : 0000:01:00.0
9000-9fff : PCI Bus 0000:02
9000-90ff : 0000:02:04.0
9400-94ff : 0000:02:0a.0
9400-94ff : CMI8738-MC6
9800-980f : 0000:02:08.0
9810-9817 : 0000:02:08.0
9818-981f : 0000:02:08.0
9820-9823 : 0000:02:08.0
9824-9827 : 0000:02:08.0
a000-a07f : 0000:00:03.0
a000-a07f : tulip
a080-a08f : 0000:00:07.1
a080-a08f : cy82c693
aleph:~# car /proc/iomem
09000000-090fffff : PCI Bus 0000:01
09000000-0900ffff : 0000:01:00.0
09010000-09013fff : 0000:01:00.1
09010000-09013fff : ICH HD audio
09100000-091fffff : PCI Bus 0000:02
09100000-09100fff : 0000:02:04.0
09101000-091011ff : 0000:02:08.0
09101000-091011ff : sata_sil
09200000-092fffff : PCI Bus 0000:02
09200000-0927ffff : 0000:02:08.0
09280000-0928ffff : 0000:02:04.0
09300000-0933ffff : 0000:00:03.0
09340000-0934ffff : 0000:00:07.2
09340000-0934ffff : cy82c693
09350000-09350fff : 0000:00:07.3
09350000-09350fff : ohci_hcd
09351000-0935107f : 0000:00:03.0
09351000-0935107f : tulip
10000000-27ffffff : PCI Bus 0000:01
10000000-1fffffff : 0000:01:00.0
20000000-2001ffff : 0000:01:00.0
aleph:~# lspci -vvv
00:03.0 Ethernet controller: Digital Equipment Corporation DECchip
21142/43 (rev 30)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 255 (5000ns min, 10000ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 24
Region 0: I/O ports at a000 [size=128]
Region 1: Memory at 09351000 (32-bit, non-prefetchable) [size=128]
Expansion ROM at 09300000 [disabled] [size=256K]
Kernel driver in use: tulip
Kernel modules: tulip
00:07.0 ISA bridge: Contaq Microsystems 82c693
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Kernel modules: cy82c693
00:07.1 IDE interface: Contaq Microsystems 82c693 (prog-if 80 [Master])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 0
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 4: I/O ports at a080 [size=16]
Kernel driver in use: Cypress_IDE
Kernel modules: cy82c693, ide-pci-generic
00:07.2 IDE interface: Contaq Microsystems 82c693 (prog-if 00 [])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 0
Region 0: I/O ports at 0170 [size=8]
Region 1: I/O ports at 0374 [size=1]
Region 4: Memory at 09340000 (32-bit, non-prefetchable) [disabled]
[size=64K]
Kernel modules: cy82c693, ide-pci-generic
00:07.3 USB Controller: Contaq Microsystems 82c693 (prog-if 10 [OHCI])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 248
Interrupt: pin A routed to IRQ 10
Region 0: Memory at 09350000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
Kernel modules: cy82c693, ohci-hcd
00:0c.0 PCI bridge: PLX Technology, Inc. PEX8112 x1 Lane PCI
Express-to-PCI Bridge (rev aa) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 255, Cache Line Size: 64 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=255
I/O behind bridge: 00008000-00008fff
Memory behind bridge: 09000000-090fffff
Prefetchable memory behind bridge: 10000000-27ffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA
PME(D0+,D1+,D2-,D3hot+,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [60] Express (v1) PCI/PCI-X to PCI-Express Bridge, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns,
L1 <1us
ExtTag- RBE- FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- BrConfRtry-
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr-
TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1,
Latency L0 <1us, L1 <16us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk-
DLActive- BWMgmt- ABWMgmt-
00:14.0 PCI bridge: Digital Equipment Corporation DECchip 21152 (rev 02)
(prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 255, Cache Line Size: 64 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=255
I/O behind bridge: 00009000-00009fff
Memory behind bridge: 09100000-091fffff
Prefetchable memory behind bridge: 0000000009200000-00000000092fffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort+ >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
01:00.0 VGA compatible controller: ATI Technologies Inc RV 610LE PCI
[Radeon HD 2400] (prog-if 00 [VGA controller])
Subsystem: Device 2232:1787
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 32
Region 0: Memory at 10000000 (64-bit, prefetchable) [size=256M]
Region 2: Memory at 09000000 (64-bit, non-prefetchable) [size=64K]
Region 4: I/O ports at 8000 [size=256]
Expansion ROM at 20000000 [disabled] [size=128K]
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Express (v1) Legacy Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <4us,
L1 unlimited
ExtTag+ AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr+ FatalErr- UnsuppReq+ AuxPwr-
TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x16, ASPM L0s L1,
Latency L0 <64ns, L1 <1us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+
DLActive- BWMgmt- ABWMgmt-
Capabilities: [a0] MSI: Enable- Count=1/1 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [100] #1002
Capabilities: [aa1] #ffff
01:00.1 Audio device: ATI Technologies Inc RV610 audio device [Radeon HD
2400 PRO]
Subsystem: Device 2232:aa10
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx+
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 33
Region 0: Memory at 09010000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Express (v1) Legacy Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <4us,
L1 unlimited
ExtTag+ AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr+ FatalErr- UnsuppReq+ AuxPwr-
TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x16, ASPM L0s L1,
Latency L0 <64ns, L1 <1us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+
DLActive- BWMgmt- ABWMgmt-
Capabilities: [a0] MSI: Enable- Count=1/1 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [100] #1002
Capabilities: [aa1] #ffff
Kernel driver in use: HDA Intel
Kernel modules: snd-hda-intel
02:04.0 SCSI storage controller: QLogic Corp. ISP1020 Fast-wide SCSI
(rev 05)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 248, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 27
Region 0: I/O ports at 9000 [size=256]
Region 1: Memory at 09100000 (32-bit, non-prefetchable) [size=4K]
Expansion ROM at 09280000 [disabled] [size=64K]
Kernel driver in use: qla1280
02:08.0 RAID bus controller: Silicon Image, Inc. SiI 3112
[SATALink/SATARaid] Serial ATA Controller (rev 02)
Subsystem: Silicon Image, Inc. SiI 3112 SATARaid Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 240, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 36
Region 0: I/O ports at 9810 [size=8]
Region 1: I/O ports at 9820 [size=4]
Region 2: I/O ports at 9818 [size=8]
Region 3: I/O ports at 9824 [size=4]
Region 4: I/O ports at 9800 [size=16]
Region 5: Memory at 09101000 (32-bit, non-prefetchable) [size=512]
Expansion ROM at 09200000 [disabled] [size=512K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=2 PME-
Kernel driver in use: sata_sil
Kernel modules: sata_sil
02:0a.0 Multimedia audio controller: C-Media Electronics Inc CM8738 (rev 10)
Subsystem: C-Media Electronics Inc CMI8738/C3DX PCI Audio Device
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 255 (500ns min, 6000ns max)
Interrupt: pin A routed to IRQ 44
Region 0: I/O ports at 9400 [size=256]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: C-Media PCI
Kernel modules: snd-cmipci
Cheerz
Michael.
next reply other threads:[~2009-07-15 10:41 UTC|newest]
Thread overview: 8+ messages / expand[flat|nested] mbox.gz Atom feed top
2009-07-15 10:41 Michael Cree [this message]
2009-07-16 3:16 ` Kernel 2.6.30.1 Oops on Alpha Architecture when starting Xserver Dave Airlie
2009-07-16 3:16 ` Dave Airlie
2009-07-25 9:21 ` Michael Cree
2009-07-25 22:54 ` Dave Airlie
2009-07-25 22:54 ` Dave Airlie
2009-07-26 0:05 ` Michael Cree
2009-07-26 1:26 ` Dialup Jon Norstog
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=4A5DB243.2000100@orcon.net.nz \
--to=mcree@orcon.net.nz \
--cc=linux-alpha@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.