From: Ivan Kuten <ivan.kuten@promwad.com>
To: linux-wireless@vger.kernel.org
Cc: "Luis R. Rodriguez" <mcgrof@gmail.com>
Subject: Re: WPA2, compat-wireless-2.6.31-rc3, kernel 2.6.28 - rtl8187 - association works but no ping
Date: Fri, 24 Jul 2009 11:13:39 +0300 [thread overview]
Message-ID: <4A696D33.8050606@promwad.com> (raw)
In-Reply-To: <43e72e890907230917w226c4697v41f907623e5f7d8@mail.gmail.com>
> On Thu, Jul 23, 2009 at 2:22 AM, Ivan Kuten<ivan.kuten@promwad.com> wrote:
>> compat-wireless-2.6.31-rc3
>
> compat-wireless-2.6.31-rc4 is out, please try that.
>
> Luis
>
Here is what I get for compat-wireless-2.6.31-rc4:
<6>cfg80211: Using static regulatory domain info
<6>cfg80211: Regulatory domain: US
<6> (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
<6> (2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm)
<6> (5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
<6> (5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
<6> (5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
<6> (5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
<6> (5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm)
<6>usb 1-1: new high speed USB device using isp1761 and address 2
<6>cfg80211: Calling CRDA for country: US
<6>usbcore: registered new interface driver rtl8187
<6>usb 1-1: configuration #1 chosen from 1 choice
<6>hub 1-1:1.0: USB hub found
<6>hub 1-1:1.0: 3 ports detected
<6>usb 1-1.1: new high speed USB device using isp1761 and address 3
<6>usb 1-1.1: configuration #1 chosen from 1 choice
<7>phy0: Selected rate control algorithm 'minstrel'
<6>phy0: hwaddr 00277080, RTL8187vB (default) V1 + rtl8225z2
<7>phy0: device now idle
<7>phy0: device no longer idle - scanning
<7>phy0: device now idle
<7>phy0: device no longer idle - in use
<7>wlan0: authenticate with AP 01a4b568
<7>wlan0: authenticated
<7>wlan0: associate with AP 01a4b568
<7>wlan0: RX AssocResp from 003e101a (capab=0x411 status=0 aid=2)
<7>wlan0: associated
<7>phy0: Allocated STA 002fbfc4
<7>phy0: Inserted STA 002fbfc4
<7>wlan0: switched to short slot time (BSSID=01a4b568)
iwconfig output:
lo no wireless extensions.
eth0 no wireless extensions.
wmaster0 no wireless extensions.
wlan0 IEEE 802.11bg ESSID:"ACORP"
Mode:Managed Frequency:2.462 GHz Access Point: 00:02:72:74:AC:85
Bit Rate=1 Mb/s Tx-Power=27 dBm
Retry long limit:7 RTS thr:off Fragment thr:off
Encryption key:2BAC-63B9-5D99-CF9A-4D39-079F-BB55-5D39 [2]
Power Management:off
Link Quality=61/70 Signal level=-49 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
ifconfig:
eth0 Link encap:Ethernet HWaddr 02:80:AD:20:31:EB
inet addr:192.168.5.1 Bcast:192.168.5.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:40 errors:0 dropped:0 overruns:0 frame:0
TX packets:188 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:4077 (3.9 KiB) TX bytes:17012 (16.6 KiB)
wlan0 Link encap:Ethernet HWaddr 00:12:0E:98:67:FC
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:2 errors:0 dropped:0 overruns:0 frame:0
TX packets:8 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:304 (304.0 B) TX bytes:3932 (3.8 KiB)
wmaster0 Link encap:UNSPEC HWaddr 00-12-0E-98-67-FC-00-00-00-00-00-00-00-00-00-00
UP RUNNING MTU:0 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
Neither dhcp nor setting static IP for wlan0 - no ping.
Regards,
Ivan
next prev parent reply other threads:[~2009-07-24 8:13 UTC|newest]
Thread overview: 7+ messages / expand[flat|nested] mbox.gz Atom feed top
2009-07-23 9:22 WPA2, compat-wireless-2.6.31-rc3, kernel 2.6.28 - rtl8187 - association works but no ping Ivan Kuten
2009-07-23 16:17 ` Luis R. Rodriguez
2009-07-24 8:13 ` Ivan Kuten [this message]
2009-07-24 15:24 ` Luis R. Rodriguez
2009-07-24 15:52 ` Ivan Kuten
2009-07-24 16:23 ` Luis R. Rodriguez
2009-07-24 16:40 ` Ivan Kuten
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=4A696D33.8050606@promwad.com \
--to=ivan.kuten@promwad.com \
--cc=linux-wireless@vger.kernel.org \
--cc=mcgrof@gmail.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.