[U-Boot] [PATCH 5/5 v3] ARM:OMAP3:SDP3430: initial support

[Dirk Behme <dirk.behme@googlemail.com>]

Nishanth Menon wrote:
> From: David Brownell <david-b@pacbell.net>
> 
> ----
> Sandeep pointed me to:
> http://lists.denx.de/pipermail/u-boot/2009-October/062086.html
> so the v3 of patch with size fixes
> ----
> Start of support of
> Texas Instruments Software Development Platform(SDP)
> for OMAP3430 - SDP3430

Having this in u-boot-ti/next and building omap3_sdp3430 gives

eth.c:497:2: warning: #warning Ethernet driver is deprecated. Please 
update to use CONFIG_NET_MULTI

Please fix.

Thanks

Dirk

> Highlights of this platform are:
> Flash Memory devices:
> 	Sibley NOR, Micron 8bit NAND and OneNAND
> Connectivity:
> 	3 UARTs and expanded 4 UART ports + IrDA
> 	Ethernet, USB
> Other peripherals:
> 	TWL5030 PMIC+Audio+Keypad
> 	VGA display
> Expansion ports:
> 	Memory devices plugin boards (PISMO)
> 	Connectivity board for GPS,WLAN etc..
> Completely configurable boot sequence and device mapping
> etc..
> For more details, please refer:
> http://focus.ti.com/general/docs/wtbu/wtbugencontent.tsp?templateId=6123&navigationId=12013&contentId=28741
> 
> Support default jumpering and:
>  - UART1/ttyS0 console(legacy sdp3430 u-boot)
>  - UART3/ttyS2 console (matching other boards,
> 		 and SDP HW docs)
>  - Ethernet
>  - mmc0
>  - NOR boot
> 
> TODO:
>  - mmc1
>  - NAND (boot or 128M storage)
>  - OneNAND (boot or 256M storage)
>  - Fix NOR env variable load
>  - Review SDRC timing configuration/DPLL
> 	configuration
>  - Dynamically read FPGA dip switch settings and
>  	map NOR/NAND/ONENAND devices to right
> 	chipselects
> 
> Currently the UART1 is enabled by default.  for
> compatibility with other OMAP3 u-boot platforms,
> enable the #define of CONSOLE_J9.
> 
> Signed-off-by: David Brownell <david-b@pacbell.net>
> Signed-off-by: Nishanth Menon <nm@ti.com>
> Cc: Vikram Pandita <vikram.pandita@ti.com>
> Cc: Richard Woodruff <r-woodruff2@ti.com>
> Cc: Sandeep Paulraj <s-paulraj@ti.com>
> Cc: Tom Rix <tom.rix@windriver.com>
> Cc: Dirk Behme <dirk.behme@googlemail.com>
> ---
>  MAINTAINERS                     |    1 +
>  MAKEALL                         |    1 +
>  Makefile                        |    3 +
>  board/ti/sdp3430/Makefile       |   49 +++++
>  board/ti/sdp3430/config.mk      |   33 +++
>  board/ti/sdp3430/sdp.c          |  204 +++++++++++++++++++
>  board/ti/sdp3430/sdp.h          |  417 +++++++++++++++++++++++++++++++++++++++
>  include/configs/omap3_sdp3430.h |  369 ++++++++++++++++++++++++++++++++++
>  8 files changed, 1077 insertions(+), 0 deletions(-)
>  create mode 100644 board/ti/sdp3430/Makefile
>  create mode 100644 board/ti/sdp3430/config.mk
>  create mode 100644 board/ti/sdp3430/sdp.c
>  create mode 100644 board/ti/sdp3430/sdp.h
>  create mode 100644 include/configs/omap3_sdp3430.h
> 
> diff --git a/MAINTAINERS b/MAINTAINERS
> index 2297651..5742782 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -628,6 +628,7 @@ Guennadi Liakhovetski <g.liakhovetski@gmx.de>
>  
>  Nishanth Menon <nm@ti.com>
>  
> +	omap3_sdp3430	ARM CORTEX-A8 (OMAP3xx SoC)
>  	omap3_zoom1	ARM CORTEX-A8 (OMAP3xx SoC)
>  
>  David M?ller <d.mueller@elsoft.ch>
> diff --git a/MAKEALL b/MAKEALL
> index 38cd076..9bf75e8 100755
> --- a/MAKEALL
> +++ b/MAKEALL
> @@ -603,6 +603,7 @@ LIST_ARM_CORTEX_A8="		\
>  	omap3_overo		\
>  	omap3_evm		\
>  	omap3_pandora		\
> +	omap3_sdp3430		\
>  	omap3_zoom1		\
>  	omap3_zoom2		\
>  "
> diff --git a/Makefile b/Makefile
> index 9637643..8dbe552 100644
> --- a/Makefile
> +++ b/Makefile
> @@ -3144,6 +3144,9 @@ omap3_zoom1_config :	unconfig
>  omap3_zoom2_config :	unconfig
>  	@$(MKCONFIG) $(@:_config=) arm arm_cortexa8 zoom2 logicpd omap3
>  
> +omap3_sdp3430_config :	unconfig
> +	@$(MKCONFIG) $(@:_config=) arm arm_cortexa8 sdp3430 ti omap3
> +
>  #########################################################################
>  ## XScale Systems
>  #########################################################################
> diff --git a/board/ti/sdp3430/Makefile b/board/ti/sdp3430/Makefile
> new file mode 100644
> index 0000000..2554c7b
> --- /dev/null
> +++ b/board/ti/sdp3430/Makefile
> @@ -0,0 +1,49 @@
> +#
> +# (C) Copyright 2000, 2001, 2002
> +# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
> +#
> +# See file CREDITS for list of people who contributed to this
> +# project.
> +#
> +# This program is free software; you can redistribute it and/or
> +# modify it under the terms of the GNU General Public License as
> +# published by the Free Software Foundation; either version 2 of
> +# the License, or (at your option) any later version.
> +#
> +# This program is distributed in the hope that it will be useful,
> +# but WITHOUT ANY WARRANTY; without even the implied warranty of
> +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> +# GNU General Public License for more details.
> +#
> +# You should have received a copy of the GNU General Public License
> +# along with this program; if not, write to the Free Software
> +# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
> +# MA 02111-1307 USA
> +#
> +
> +include $(TOPDIR)/config.mk
> +
> +LIB	= $(obj)lib$(BOARD).a
> +
> +COBJS	:= sdp.o
> +
> +SRCS	:= $(COBJS:.o=.c)
> +OBJS	:= $(addprefix $(obj),$(COBJS))
> +
> +$(LIB):	$(obj).depend $(OBJS)
> +	$(AR) $(ARFLAGS) $@ $(OBJS)
> +
> +clean:
> +	rm -f $(OBJS)
> +
> +distclean:	clean
> +	rm -f $(LIB) core *.bak $(obj).depend
> +
> +#########################################################################
> +
> +# defines $(obj).depend target
> +include $(SRCTREE)/rules.mk
> +
> +sinclude $(obj).depend
> +
> +#########################################################################
> diff --git a/board/ti/sdp3430/config.mk b/board/ti/sdp3430/config.mk
> new file mode 100644
> index 0000000..18e4761
> --- /dev/null
> +++ b/board/ti/sdp3430/config.mk
> @@ -0,0 +1,33 @@
> +#
> +# (C) Copyright 2006-2009
> +# Texas Instruments Incorporated, <www.ti.com>
> +#
> +# OMAP 3430 SDP uses OMAP3 (ARM-CortexA8) cpu
> +# see http://www.ti.com/ for more information on Texas Instruments
> +#
> +# See file CREDITS for list of people who contributed to this
> +# project.
> +#
> +# This program is free software; you can redistribute it and/or
> +# modify it under the terms of the GNU General Public License as
> +# published by the Free Software Foundation; either version 2 of
> +# the License, or (at your option) any later version.
> +#
> +# This program is distributed in the hope that it will be useful,
> +# but WITHOUT ANY WARRANTY; without even the implied warranty of
> +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> +# GNU General Public License for more details.
> +#
> +# You should have received a copy of the GNU General Public License
> +# along with this program; if not, write to the Free Software
> +# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
> +# MA 02111-1307 USA
> +#
> +# Physical Address:
> +# 8000'0000 (bank0)
> +# A000/0000 (bank1)
> +# Linux-Kernel is expected to be at 8000'8000, entry 8000'8000
> +# (mem base + reserved)
> +
> +# For use with external or internal boots.
> +TEXT_BASE = 0x80e80000
> diff --git a/board/ti/sdp3430/sdp.c b/board/ti/sdp3430/sdp.c
> new file mode 100644
> index 0000000..40cf26f
> --- /dev/null
> +++ b/board/ti/sdp3430/sdp.c
> @@ -0,0 +1,204 @@
> +/*
> + * (C) Copyright 2004-2009
> + * Texas Instruments Incorporated, <www.ti.com>
> + * Richard Woodruff <r-woodruff2@ti.com>
> + *
> + * See file CREDITS for list of people who contributed to this
> + * project.
> + *
> + * This program is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation; either version 2 of
> + * the License, or (at your option) any later version.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * You should have received a copy of the GNU General Public License
> + * along with this program; if not, write to the Free Software
> + * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
> + * MA 02111-1307 USA
> + */
> +#include <common.h>
> +#include <twl4030.h>
> +#include <asm/io.h>
> +#include <asm/arch/mux.h>
> +#include <asm/arch/mem.h>
> +#include <asm/arch/sys_proto.h>
> +#include <asm/mach-types.h>
> +#include "sdp.h"
> +
> +const omap3_sysinfo sysinfo = {
> +	DDR_DISCRETE,
> +	"OMAP3 SDP3430 board",
> +#if defined(CONFIG_ENV_IS_IN_ONENAND)
> +	"OneNAND",
> +#elif defined(CONFIG_ENV_IS_IN_NAND)
> +	"NAND",
> +#else
> +	"NOR",
> +#endif
> +};
> +
> +/* Timing definitions for GPMC controller for Sibley NOR */
> +static const u32 gpmc_sdp_nor[] = {
> +    SDP3430_NOR_GPMC_CONF1,
> +    SDP3430_NOR_GPMC_CONF2,
> +    SDP3430_NOR_GPMC_CONF3,
> +    SDP3430_NOR_GPMC_CONF4,
> +    SDP3430_NOR_GPMC_CONF5,
> +    SDP3430_NOR_GPMC_CONF6,
> +    /*CONF7- computed as params */
> +};
> +
> +/*
> + * Timing definitions for GPMC controller for Debug Board
> + * Debug board contains access to ethernet and DIP Switch setting
> + * information etc.
> + */
> +static const u32 gpmc_sdp_debug[] = {
> +    SDP3430_DEBUG_GPMC_CONF1,
> +    SDP3430_DEBUG_GPMC_CONF2,
> +    SDP3430_DEBUG_GPMC_CONF3,
> +    SDP3430_DEBUG_GPMC_CONF4,
> +    SDP3430_DEBUG_GPMC_CONF5,
> +    SDP3430_DEBUG_GPMC_CONF6,
> +    /*CONF7- computed as params */
> +};
> +
> +/* Timing defintions for GPMC OneNAND */
> +static const u32 gpmc_sdp_onenand[] = {
> +    SDP3430_ONENAND_GPMC_CONF1,
> +    SDP3430_ONENAND_GPMC_CONF2,
> +    SDP3430_ONENAND_GPMC_CONF3,
> +    SDP3430_ONENAND_GPMC_CONF4,
> +    SDP3430_ONENAND_GPMC_CONF5,
> +    SDP3430_ONENAND_GPMC_CONF6,
> +    /*CONF7- computed as params */
> +};
> +
> +/* GPMC definitions for GPMC NAND */
> +static const u32 gpmc_sdp_nand[] = {
> +    SDP3430_NAND_GPMC_CONF1,
> +    SDP3430_NAND_GPMC_CONF2,
> +    SDP3430_NAND_GPMC_CONF3,
> +    SDP3430_NAND_GPMC_CONF4,
> +    SDP3430_NAND_GPMC_CONF5,
> +    SDP3430_NAND_GPMC_CONF6,
> +    /*CONF7- computed as params */
> +};
> +
> +/* gpmc_cfg is initialized by gpmc_init and we use it here */
> +extern struct gpmc *gpmc_cfg;
> +
> +/**
> + * @brief board_init - gpmc and basic setup as phase1 of boot sequence
> + *
> + * @return 0
> + */
> +int board_init(void)
> +{
> +	DECLARE_GLOBAL_DATA_PTR;
> +
> +	gpmc_init(); /* in SRAM or SDRAM, finish GPMC */
> +	/* TODO: Dynamically pop out CS mapping and program accordingly */
> +	/* Configure devices for default ON ON ON settings */
> +	enable_gpmc_cs_config(gpmc_sdp_nor, &gpmc_cfg->cs[0],
> +			CONFIG_SYS_FLASH_BASE, GPMC_SIZE_128M);
> +	enable_gpmc_cs_config(gpmc_sdp_nand, &gpmc_cfg->cs[1], 0x28000000,
> +			GPMC_SIZE_16M);
> +	enable_gpmc_cs_config(gpmc_sdp_onenand, &gpmc_cfg->cs[2], 0x20000000,
> +			GPMC_SIZE_16M);
> +	enable_gpmc_cs_config(gpmc_sdp_debug, &gpmc_cfg->cs[3], DEBUG_BASE,
> +			GPMC_SIZE_16M);
> +	/* board id for Linux */
> +	gd->bd->bi_arch_number = MACH_TYPE_OMAP_3430SDP;
> +	/* boot param addr */
> +	gd->bd->bi_boot_params = (OMAP34XX_SDRC_CS0 + 0x100);
> +
> +	return 0;
> +}
> +
> +#define LAN_RESET_REGISTER	(CONFIG_LAN91C96_BASE + 0x01c)
> +#define ETH_CONTROL_REG		(CONFIG_LAN91C96_BASE + 0x30b)
> +
> +/**
> + * @brief ether_init Take the Ethernet controller out of reset and wait
> + * for the EEPROM load to complete.
> + */
> +static void ether_init(void)
> +{
> +#ifdef CONFIG_DRIVER_LAN91C96
> +	int cnt = 20;
> +
> +	writew(0x0, LAN_RESET_REGISTER);
> +	do {
> +		writew(0x1, LAN_RESET_REGISTER);
> +		udelay(100);
> +		if (cnt == 0)
> +			goto reset_err_out;
> +		--cnt;
> +	} while (readw(LAN_RESET_REGISTER) != 0x1);
> +
> +	cnt = 20;
> +
> +	do {
> +		writew(0x0, LAN_RESET_REGISTER);
> +		udelay(100);
> +		if (cnt == 0)
> +			goto reset_err_out;
> +		--cnt;
> +	} while (readw(LAN_RESET_REGISTER) != 0x0000);
> +	udelay(1000);
> +
> +	writeb(readb(ETH_CONTROL_REG) & ~0x1, ETH_CONTROL_REG);
> +	udelay(1000);
> +reset_err_out:
> +	return;
> +
> +#endif
> +}
> +
> +/**
> + * @brief misc_init_r - Configure SDP board specific configurations
> + * such as power configurations, ethernet initialization as phase2 of
> + * boot sequence
> + *
> + * @return 0
> + */
> +int misc_init_r(void)
> +{
> +	/* Partial setup:
> +	 *   VAUX3 - 2.8V for DVI
> +	 *   VPLL1 - 1.8V
> +	 *   VDAC  - 1.8V
> +	 * and turns on LEDA/LEDB (not needed ... NOP?)
> +	 */
> +	twl4030_power_init();
> +
> +	/* FIXME finish setup:
> +	 *   VAUX1 - 2.8V for mainboard I/O
> +	 *   VAUX2 - 2.8V for camera
> +	 *   VAUX4 - 1.8V for OMAP3 CSI
> +	 *   VMMC1 - 3.15V (init, variable) for MMC1
> +	 *   VMMC2 - 1.85V for MMC2
> +	 *   VSIM  - off (init, variable) for MMC1.DAT[3..7], SIM
> +	 *   VPLL2 - 1.8V
> +	 */
> +	ether_init();
> +
> +	return 0;
> +}
> +
> +/**
> + * @brief set_muxconf_regs Setting up the configuration Mux registers
> + * specific to the hardware. Many pins need to be moved from protect
> + * to primary mode.
> + */
> +void set_muxconf_regs(void)
> +{
> +	/* platform specific muxes */
> +	MUX_SDP3430();
> +}
> diff --git a/board/ti/sdp3430/sdp.h b/board/ti/sdp3430/sdp.h
> new file mode 100644
> index 0000000..3526e94
> --- /dev/null
> +++ b/board/ti/sdp3430/sdp.h
> @@ -0,0 +1,417 @@
> +/*
> + * (C) Copyright 2004-2009
> + * Texas Instruments Incorporated
> + * Richard Woodruff <r-woodruff2@ti.com>
> + *
> + * See file CREDITS for list of people who contributed to this
> + * project.
> + *
> + * This program is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation; either version 2 of
> + * the License, or (at your option) any later version.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * You should have received a copy of the GNU General Public License
> + * along with this program; if not, write to the Free Software
> + * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
> + * MA 02111-1307 USA
> + */
> +#ifndef _BOARD_SDP_H_
> +#define _BOARD_SDP_H_
> +
> +#define OFF_IN_PD	0
> +#define OFF_OUT_PD	0
> +
> +/*
> + * IEN	- Input Enable
> + * IDIS	- Input Disable
> + * PTD	- Pull type Down
> + * PTU	- Pull type Up
> + * DIS	- Pull type selection is inactive
> + * EN	- Pull type selection is active
> + * M0	- Mode 0
> + * The commented string gives the final mux configuration for that pin
> + */
> +#define MUX_SDP3430()\
> +	/*SDRC*/\
> +	MUX_VAL(CP(SDRC_D0), (IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(SDRC_D1), (IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(SDRC_D2), (IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(SDRC_D3), (IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(SDRC_D4), (IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(SDRC_D5), (IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(SDRC_D6), (IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(SDRC_D7), (IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(SDRC_D8), (IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(SDRC_D9), (IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(SDRC_D10), (IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(SDRC_D11), (IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(SDRC_D12), (IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(SDRC_D13), (IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(SDRC_D14), (IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(SDRC_D15), (IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(SDRC_D16), (IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(SDRC_D17), (IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(SDRC_D18), (IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(SDRC_D19), (IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(SDRC_D20), (IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(SDRC_D21), (IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(SDRC_D22), (IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(SDRC_D23), (IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(SDRC_D24), (IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(SDRC_D25), (IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(SDRC_D26), (IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(SDRC_D27), (IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(SDRC_D28), (IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(SDRC_D29), (IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(SDRC_D30), (IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(SDRC_D31), (IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(SDRC_CLK), (IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(SDRC_DQS0), (IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(SDRC_DQS1), (IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(SDRC_DQS2), (IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(SDRC_DQS3), (IEN | PTD | DIS | M0))\
> +	/*GPMC*/\
> +	MUX_VAL(CP(GPMC_A1), (OFF_OUT_PD | IDIS | PTD | DIS | M0))\
> +	MUX_VAL(CP(GPMC_A2), (OFF_OUT_PD | IDIS | PTD | DIS | M0))\
> +	MUX_VAL(CP(GPMC_A3), (OFF_OUT_PD | IDIS | PTD | DIS | M0))\
> +	MUX_VAL(CP(GPMC_A4), (OFF_OUT_PD | IDIS | PTD | DIS | M0))\
> +	MUX_VAL(CP(GPMC_A5), (OFF_OUT_PD | IDIS | PTD | DIS | M0))\
> +	MUX_VAL(CP(GPMC_A6), (OFF_OUT_PD | IDIS | PTD | DIS | M0))\
> +	MUX_VAL(CP(GPMC_A7), (OFF_OUT_PD | IDIS | PTD | DIS | M0))\
> +	MUX_VAL(CP(GPMC_A8), (OFF_OUT_PD | IDIS | PTD | DIS | M0))\
> +	MUX_VAL(CP(GPMC_A9), (OFF_OUT_PD | IDIS | PTD | DIS | M0))\
> +	MUX_VAL(CP(GPMC_A10), (OFF_OUT_PD | IDIS | PTD | DIS | M0))\
> +	MUX_VAL(CP(GPMC_D0), (OFF_IN_PD | IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(GPMC_D1), (OFF_IN_PD | IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(GPMC_D2), (OFF_IN_PD | IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(GPMC_D3), (OFF_IN_PD | IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(GPMC_D4), (OFF_IN_PD | IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(GPMC_D5), (OFF_IN_PD | IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(GPMC_D6), (OFF_IN_PD | IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(GPMC_D7), (OFF_IN_PD | IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(GPMC_D8), (OFF_IN_PD | IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(GPMC_D9), (OFF_IN_PD | IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(GPMC_D10), (OFF_IN_PD | IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(GPMC_D11), (OFF_IN_PD | IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(GPMC_D12), (OFF_IN_PD | IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(GPMC_D13), (OFF_IN_PD | IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(GPMC_D14), (OFF_IN_PD | IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(GPMC_D15), (OFF_IN_PD | IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(GPMC_NCS0), (OFF_OUT_PD | IDIS | PTU | EN | M0))\
> +	MUX_VAL(CP(GPMC_NCS1), (OFF_OUT_PD | IDIS | PTU | EN | M0))\
> +	MUX_VAL(CP(GPMC_NCS2), (OFF_OUT_PD | IDIS | PTU | EN | M0))\
> +	MUX_VAL(CP(GPMC_NCS3), (OFF_OUT_PD | IDIS | PTU | EN | M0))\
> +	MUX_VAL(CP(GPMC_NCS4), (OFF_IN_PD | IEN | PTU | EN | M4)) /*G55-F_DIS*/\
> +	MUX_VAL(CP(GPMC_NCS5), (OFF_OUT_PD | IDIS | PTD | DIS | M4))/*G56T_EN*/\
> +	MUX_VAL(CP(GPMC_NCS6), (OFF_IN_PD | IEN | PTD | DIS | M4))/*G57-AGPSP*/\
> +	MUX_VAL(CP(GPMC_NCS7), (OFF_IN_PD | IEN | PTU | EN | M4))/*G58-WLNIQ*/\
> +	MUX_VAL(CP(GPMC_CLK), (OFF_OUT_PD | IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(GPMC_NADV_ALE), (OFF_OUT_PD | IDIS | PTD | DIS | M0))\
> +	MUX_VAL(CP(GPMC_NOE), (OFF_OUT_PD | IDIS | PTD | DIS | M0))\
> +	MUX_VAL(CP(GPMC_NWE), (OFF_OUT_PD | IDIS | PTD | DIS | M0))\
> +	MUX_VAL(CP(GPMC_NBE0_CLE), (OFF_OUT_PD | IDIS | PTD | DIS | M0))\
> +	MUX_VAL(CP(GPMC_NBE1), (OFF_IN_PD | IEN | PTD | DIS | M4)) /*G61-BTST*/\
> +	MUX_VAL(CP(GPMC_NWP), (OFF_IN_PD | IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(GPMC_WAIT0), (OFF_IN_PD | IEN | PTU | EN | M0))\
> +	MUX_VAL(CP(GPMC_WAIT1), (OFF_IN_PD | IEN | PTU | EN | M0))\
> +	MUX_VAL(CP(GPMC_WAIT2), (OFF_IN_PD | IEN | PTU | EN | M4)) /*GPIO_64*/\
> +	MUX_VAL(CP(GPMC_WAIT3), (OFF_IN_PD | IEN | PTU | EN | M4)) /*GPIO_65*/\
> +	/*DSS*/\
> +	MUX_VAL(CP(DSS_PCLK), (OFF_OUT_PD | IDIS | PTD | DIS | M0))\
> +	MUX_VAL(CP(DSS_HSYNC), (OFF_OUT_PD | IDIS | PTD | DIS | M0))\
> +	MUX_VAL(CP(DSS_VSYNC), (OFF_OUT_PD | IDIS | PTD | DIS | M0))\
> +	MUX_VAL(CP(DSS_ACBIAS), (OFF_OUT_PD | IDIS | PTD | DIS | M0))\
> +	MUX_VAL(CP(DSS_DATA0), (OFF_OUT_PD | IDIS | PTD | DIS | M0))\
> +	MUX_VAL(CP(DSS_DATA1), (OFF_OUT_PD | IDIS | PTD | DIS | M0))\
> +	MUX_VAL(CP(DSS_DATA2), (OFF_OUT_PD | IDIS | PTD | DIS | M0))\
> +	MUX_VAL(CP(DSS_DATA3), (OFF_OUT_PD | IDIS | PTD | DIS | M0))\
> +	MUX_VAL(CP(DSS_DATA4), (OFF_OUT_PD | IDIS | PTD | DIS | M0))\
> +	MUX_VAL(CP(DSS_DATA5), (OFF_OUT_PD | IDIS | PTD | DIS | M0))\
> +	MUX_VAL(CP(DSS_DATA6), (OFF_OUT_PD | IDIS | PTD | DIS | M0))\
> +	MUX_VAL(CP(DSS_DATA7), (OFF_OUT_PD | IDIS | PTD | DIS | M0))\
> +	MUX_VAL(CP(DSS_DATA8), (OFF_OUT_PD | IDIS | PTD | DIS | M0))\
> +	MUX_VAL(CP(DSS_DATA9), (OFF_OUT_PD | IDIS | PTD | DIS | M0))\
> +	MUX_VAL(CP(DSS_DATA10), (OFF_OUT_PD | IDIS | PTD | DIS | M0))\
> +	MUX_VAL(CP(DSS_DATA11), (OFF_OUT_PD | IDIS | PTD | DIS | M0))\
> +	MUX_VAL(CP(DSS_DATA12), (OFF_OUT_PD | IDIS | PTD | DIS | M0))\
> +	MUX_VAL(CP(DSS_DATA13), (OFF_OUT_PD | IDIS | PTD | DIS | M0))\
> +	MUX_VAL(CP(DSS_DATA14), (OFF_OUT_PD | IDIS | PTD | DIS | M0))\
> +	MUX_VAL(CP(DSS_DATA15), (OFF_OUT_PD | IDIS | PTD | DIS | M0))\
> +	MUX_VAL(CP(DSS_DATA16), (OFF_OUT_PD | IDIS | PTD | DIS | M0))\
> +	MUX_VAL(CP(DSS_DATA17), (OFF_OUT_PD | IDIS | PTD | DIS | M0))\
> +	MUX_VAL(CP(DSS_DATA18), (OFF_OUT_PD | IDIS | PTD | DIS | M0))\
> +	MUX_VAL(CP(DSS_DATA19), (OFF_OUT_PD | IDIS | PTD | DIS | M0))\
> +	MUX_VAL(CP(DSS_DATA20), (OFF_OUT_PD | IDIS | PTD | DIS | M0))\
> +	MUX_VAL(CP(DSS_DATA21), (OFF_OUT_PD | IDIS | PTD | DIS | M0))\
> +	MUX_VAL(CP(DSS_DATA22), (OFF_OUT_PD | IDIS | PTD | DIS | M0))\
> +	MUX_VAL(CP(DSS_DATA23), (OFF_OUT_PD | IDIS | PTD | DIS | M0))\
> +	/*CAMERA*/\
> +	MUX_VAL(CP(CAM_HS), (OFF_IN_PD | IEN | PTU | EN | M0))\
> +	MUX_VAL(CP(CAM_VS), (OFF_IN_PD | IEN | PTU | EN | M0))\
> +	MUX_VAL(CP(CAM_XCLKA), (OFF_OUT_PD | IDIS | PTD | DIS | M0))\
> +	MUX_VAL(CP(CAM_PCLK), (OFF_IN_PD | IEN | PTU | EN | M0))\
> +	MUX_VAL(CP(CAM_FLD), (OFF_OUT_PD | IDIS | PTD | DIS | M4))/*G98-C_RST*/\
> +	MUX_VAL(CP(CAM_D0), (OFF_IN_PD | IEN | PTD | DIS | M2)) /*CAM_D0 */\
> +	MUX_VAL(CP(CAM_D1), (OFF_IN_PD | IEN | PTD | DIS | M2)) /*CAM_D1 */\
> +	MUX_VAL(CP(CAM_D2), (OFF_IN_PD | IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(CAM_D3), (OFF_IN_PD | IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(CAM_D4), (OFF_IN_PD | IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(CAM_D5), (OFF_IN_PD | IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(CAM_D6), (OFF_IN_PD | IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(CAM_D7), (OFF_IN_PD | IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(CAM_D8), (OFF_IN_PD | IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(CAM_D9), (OFF_IN_PD | IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(CAM_D10), (OFF_IN_PD | IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(CAM_D11), (OFF_IN_PD | IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(CAM_XCLKB), (OFF_OUT_PD | IDIS | PTD | DIS | M0))\
> +	MUX_VAL(CP(CAM_WEN), (OFF_IN_PD | IEN | PTD | DIS | M4)) /*GPIO_167*/\
> +	MUX_VAL(CP(CAM_STROBE), (OFF_OUT_PD | IDIS | PTD | DIS | M0))\
> +	MUX_VAL(CP(CSI2_DX0), (OFF_IN_PD | IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(CSI2_DY0), (OFF_IN_PD | IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(CSI2_DX1), (OFF_IN_PD | IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(CSI2_DY1), (OFF_IN_PD | IEN | PTD | DIS | M0))\
> +	/*Audio InterfACe */\
> +	MUX_VAL(CP(MCBSP2_FSX), (OFF_IN_PD | IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(MCBSP2_CLKX), (OFF_IN_PD | IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(MCBSP2_DR), (OFF_IN_PD | IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(MCBSP2_DX), (OFF_OUT_PD | IDIS | PTD | DIS | M0))\
> +	/*Expansion Card */\
> +	MUX_VAL(CP(MMC1_CLK), (OFF_OUT_PD | IDIS | PTU | EN | M0))\
> +	MUX_VAL(CP(MMC1_CMD), (OFF_IN_PD | IEN | PTU | EN | M0))\
> +	MUX_VAL(CP(MMC1_DAT0), (OFF_IN_PD | IEN | PTU | EN | M0))\
> +	MUX_VAL(CP(MMC1_DAT1), (OFF_IN_PD | IEN | PTU | EN | M0))\
> +	MUX_VAL(CP(MMC1_DAT2), (OFF_IN_PD | IEN | PTU | EN | M0))\
> +	MUX_VAL(CP(MMC1_DAT3), (OFF_IN_PD | IEN | PTU | EN | M0))\
> +	MUX_VAL(CP(MMC1_DAT4), (OFF_IN_PD | IEN | PTU | EN | M0))\
> +	MUX_VAL(CP(MMC1_DAT5), (OFF_IN_PD | IEN | PTU | EN | M0))\
> +	MUX_VAL(CP(MMC1_DAT6), (OFF_IN_PD | IEN | PTU | EN | M0))\
> +	MUX_VAL(CP(MMC1_DAT7), (OFF_IN_PD | IEN | PTU | EN | M0))\
> +	/*Wireless LAN */\
> +	MUX_VAL(CP(MMC2_CLK), (OFF_IN_PD | IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(MMC2_CMD), (OFF_IN_PD | IEN | PTU | EN | M0))\
> +	MUX_VAL(CP(MMC2_DAT0), (OFF_IN_PD | IEN | PTU | EN | M0))\
> +	MUX_VAL(CP(MMC2_DAT1), (OFF_IN_PD | IEN | PTU | EN | M0))\
> +	MUX_VAL(CP(MMC2_DAT2), (OFF_IN_PD | IEN | PTU | EN | M0))\
> +	MUX_VAL(CP(MMC2_DAT3), (OFF_IN_PD | IEN | PTU | EN | M0))\
> +	MUX_VAL(CP(MMC2_DAT4), (OFF_OUT_PD | IDIS | PTD | DIS | M1))/*DRD0*/\
> +	MUX_VAL(CP(MMC2_DAT5), (OFF_OUT_PD | IDIS | PTD | DIS | M1))/*DRD1*/\
> +	MUX_VAL(CP(MMC2_DAT6), (OFF_OUT_PD | IDIS | PTD | DIS | M1))/*DCMD*/\
> +	MUX_VAL(CP(MMC2_DAT7), (OFF_IN_PD | IEN | PTU | EN | M1))/*CLKIN*/\
> +	/*Bluetooth*/\
> +	MUX_VAL(CP(MCBSP3_DX), (OFF_OUT_PD | IDIS | PTD | DIS | M0))\
> +	MUX_VAL(CP(MCBSP3_DR), (OFF_IN_PD | IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(MCBSP3_CLKX), (OFF_IN_PD | IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(MCBSP3_FSX), (OFF_IN_PD | IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(UART2_CTS), (OFF_IN_PD | IEN | PTU | EN | M0))\
> +	MUX_VAL(CP(UART2_RTS), (OFF_OUT_PD | IDIS | PTD | DIS | M0))\
> +	MUX_VAL(CP(UART2_TX), (OFF_OUT_PD | IDIS | PTD | DIS | M0))\
> +	MUX_VAL(CP(UART2_RX), (OFF_IN_PD | IEN | PTD | DIS | M0))\
> +	/*Modem Interface */\
> +	MUX_VAL(CP(UART1_TX), (OFF_OUT_PD | IDIS | PTD | DIS | M0))\
> +	MUX_VAL(CP(UART1_RTS), (OFF_OUT_PD | IDIS | PTD | DIS | M0))\
> +	MUX_VAL(CP(UART1_CTS), (OFF_IN_PD | IEN | PTU | DIS | M0))\
> +	MUX_VAL(CP(UART1_RX), (OFF_IN_PD | IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(MCBSP4_CLKX), (OFF_IN_PD | IEN | PTD | DIS | M1))/*SSI1DRX*/\
> +	MUX_VAL(CP(MCBSP4_DR), (OFF_IN_PD | IEN | PTD | DIS | M1))/*SSI1FLGRX*/\
> +	MUX_VAL(CP(MCBSP4_DX), (OFF_IN_PD | IEN | PTD | DIS | M1))/*SSI1RDYRX*/\
> +	MUX_VAL(CP(MCBSP4_FSX), (OFF_IN_PD | IEN | PTD | DIS | M1))/*SSI1WAKE*/\
> +	MUX_VAL(CP(MCBSP1_CLKR), (OFF_IN_PD | IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(MCBSP1_FSR), (OFF_OUT_PD | IDIS | PTU | EN | M4))/*G157BWP*/\
> +	MUX_VAL(CP(MCBSP1_DX), (OFF_OUT_PD | IDIS | PTD | DIS | M0))\
> +	MUX_VAL(CP(MCBSP1_DR), (OFF_IN_PD | IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(MCBSP_CLKS), (OFF_IN_PD | IEN | PTU | DIS | M0))\
> +	MUX_VAL(CP(MCBSP1_FSX), (OFF_IN_PD | IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(MCBSP1_CLKX), (OFF_IN_PD | IEN | PTD | DIS | M0))\
> +	/*Serial Interface*/\
> +	MUX_VAL(CP(UART3_CTS_RCTX), (OFF_IN_PD | IEN | PTD | EN | M0))\
> +	MUX_VAL(CP(UART3_RTS_SD), (OFF_OUT_PD | IDIS | PTD | DIS | M0))\
> +	MUX_VAL(CP(UART3_RX_IRRX), (OFF_IN_PD | IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(UART3_TX_IRTX), (OFF_OUT_PD | IDIS | PTD | DIS | M0))\
> +	MUX_VAL(CP(HSUSB0_CLK), (OFF_IN_PD | IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(HSUSB0_STP), (OFF_OUT_PD | IDIS | PTU | EN | M0))\
> +	MUX_VAL(CP(HSUSB0_DIR), (OFF_IN_PD | IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(HSUSB0_NXT), (OFF_IN_PD | IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(HSUSB0_DATA0), (OFF_IN_PD | IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(HSUSB0_DATA1), (OFF_IN_PD | IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(HSUSB0_DATA2), (OFF_IN_PD | IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(HSUSB0_DATA3), (OFF_IN_PD | IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(HSUSB0_DATA4), (OFF_IN_PD | IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(HSUSB0_DATA5), (OFF_IN_PD | IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(HSUSB0_DATA6), (OFF_IN_PD | IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(HSUSB0_DATA7), (OFF_IN_PD | IEN | PTD | DIS | M0))\
> +	/* NOTE db: removed off-mode from I2C 1/2/3 ... external pullups!! */\
> +	MUX_VAL(CP(I2C1_SCL), (IEN | PTU | EN | M0))\
> +	MUX_VAL(CP(I2C1_SDA), (IEN | PTU | EN | M0))\
> +	MUX_VAL(CP(I2C2_SCL), (IEN | PTU | EN | M0))\
> +	MUX_VAL(CP(I2C2_SDA), (IEN | PTU | EN | M0))\
> +	MUX_VAL(CP(I2C3_SCL), (IEN | PTU | EN | M0))\
> +	MUX_VAL(CP(I2C3_SDA), (IEN | PTU | EN | M0))\
> +	MUX_VAL(CP(I2C4_SCL), (IEN | PTU | EN | M0))\
> +	MUX_VAL(CP(I2C4_SDA), (IEN | PTU | EN | M0))\
> +	MUX_VAL(CP(HDQ_SIO), (OFF_IN_PD | IEN | PTU | EN | M0))\
> +	MUX_VAL(CP(MCSPI1_CLK), (OFF_IN_PD | IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(MCSPI1_SIMO), (OFF_IN_PD | IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(MCSPI1_SOMI), (OFF_IN_PD | IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(MCSPI1_CS0), (OFF_IN_PD | IEN | PTD | EN | M0))\
> +	MUX_VAL(CP(MCSPI1_CS1), (OFF_OUT_PD | IDIS | PTD | EN | M0))\
> +	MUX_VAL(CP(MCSPI1_CS2), (OFF_OUT_PD | IDIS | PTD | DIS | M4))/*G176*/\
> +	MUX_VAL(CP(MCSPI1_CS3), (OFF_IN_PD | IEN | PTD | EN | M0))\
> +	MUX_VAL(CP(MCSPI2_CLK), (OFF_IN_PD | IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(MCSPI2_SIMO), (OFF_IN_PD | IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(MCSPI2_SOMI), (OFF_IN_PD | IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(MCSPI2_CS0), (OFF_IN_PD | IEN | PTD | EN | M0))\
> +	MUX_VAL(CP(MCSPI2_CS1), (OFF_IN_PD | IEN | PTD | EN | M0))\
> +	/*Control and debug */\
> +	MUX_VAL(CP(SYS_32K), (IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(SYS_CLKREQ), (IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(SYS_NIRQ), (OFF_IN_PD | IEN | PTU | EN | M0))\
> +	MUX_VAL(CP(SYS_BOOT0), (OFF_OUT_PD | IEN | PTD | DIS | M4))/*G2PENIRQ*/\
> +	MUX_VAL(CP(SYS_BOOT1), (OFF_OUT_PD | IEN | PTD | DIS | M4))/*GPIO_3 */\
> +	MUX_VAL(CP(SYS_BOOT2), (OFF_OUT_PD | IEN | PTD | DIS | M4))/*G4MMC1WP*/\
> +	MUX_VAL(CP(SYS_BOOT3), (OFF_OUT_PD | IEN | PTD | DIS | M4))/*G5LCDENV*/\
> +	MUX_VAL(CP(SYS_BOOT4), (OFF_OUT_PD | IEN | PTD | DIS | M4))/*G6LANINT*/\
> +	MUX_VAL(CP(SYS_BOOT5), (OFF_OUT_PD | IEN | PTD | DIS | M4))/*G7MMC2WP*/\
> +	MUX_VAL(CP(SYS_BOOT6), (OFF_OUT_PD | IDIS | PTD | DIS | M4))/*G8ENBKL*/\
> +	MUX_VAL(CP(SYS_OFF_MODE), (IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(SYS_CLKOUT1), (IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(SYS_CLKOUT2), (OFF_IN_PD | IEN | PTU | EN | M4))/*GPIO_186*/\
> +	MUX_VAL(CP(JTAG_nTRST), (IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(JTAG_TCK), (IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(JTAG_TMS), (IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(JTAG_TDI), (IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(JTAG_EMU0), (OFF_IN_PD | IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(JTAG_EMU1), (OFF_IN_PD | IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(ETK_CLK_ES2), (OFF_OUT_PD | IDIS | PTU | EN | M0))\
> +	MUX_VAL(CP(ETK_CTL_ES2), (OFF_OUT_PD | IDIS | PTD | DIS | M0))\
> +	MUX_VAL(CP(ETK_D0_ES2), (OFF_IN_PD | IEN | PTD | DIS | M1))/*USB1TLD0*/\
> +	MUX_VAL(CP(ETK_D1_ES2), (OFF_IN_PD | IEN | PTD | DIS | M1))/*SPI3_CS0*/\
> +	MUX_VAL(CP(ETK_D2_ES2), (OFF_IN_PD | IEN | PTD | EN | M1))/*USB1TLD2*/\
> +	MUX_VAL(CP(ETK_D3_ES2), (OFF_IN_PD | IEN | PTD | DIS | M1))/*USB1TLD7*/\
> +	MUX_VAL(CP(ETK_D4_ES2), (OFF_IN_PD | IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(ETK_D5_ES2), (OFF_IN_PD | IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(ETK_D6_ES2), (OFF_IN_PD | IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(ETK_D7_ES2), (OFF_IN_PD | IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(ETK_D8_ES2), (OFF_IN_PD | IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(ETK_D9_ES2), (OFF_IN_PD | IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(ETK_D10_ES2), (OFF_IN_PD | IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(ETK_D11_ES2), (OFF_IN_PD | IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(ETK_D12_ES2), (OFF_IN_PD | IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(ETK_D13_ES2), (OFF_IN_PD | IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(ETK_D14_ES2), (OFF_IN_PD | IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(ETK_D15_ES2), (OFF_IN_PD | IEN | PTD | DIS | M0))\
> +	/*Die to Die */\
> +	MUX_VAL(CP(D2D_MCAD0), (OFF_IN_PD | IEN | PTD | EN | M0))\
> +	MUX_VAL(CP(D2D_MCAD1), (OFF_IN_PD | IEN | PTD | EN | M0))\
> +	MUX_VAL(CP(D2D_MCAD2), (OFF_IN_PD | IEN | PTD | EN | M0))\
> +	MUX_VAL(CP(D2D_MCAD3), (OFF_IN_PD | IEN | PTD | EN | M0))\
> +	MUX_VAL(CP(D2D_MCAD4), (OFF_IN_PD | IEN | PTD | EN | M0))\
> +	MUX_VAL(CP(D2D_MCAD5), (OFF_IN_PD | IEN | PTD | EN | M0))\
> +	MUX_VAL(CP(D2D_MCAD6), (OFF_IN_PD | IEN | PTD | EN | M0))\
> +	MUX_VAL(CP(D2D_MCAD7), (OFF_IN_PD | IEN | PTD | EN | M0))\
> +	MUX_VAL(CP(D2D_MCAD8), (OFF_IN_PD | IEN | PTD | EN | M0))\
> +	MUX_VAL(CP(D2D_MCAD9), (OFF_IN_PD | IEN | PTD | EN | M0))\
> +	MUX_VAL(CP(D2D_MCAD10), (OFF_IN_PD | IEN | PTD | EN | M0))\
> +	MUX_VAL(CP(D2D_MCAD11), (OFF_IN_PD | IEN | PTD | EN | M0))\
> +	MUX_VAL(CP(D2D_MCAD12), (OFF_IN_PD | IEN | PTD | EN | M0))\
> +	MUX_VAL(CP(D2D_MCAD13), (OFF_IN_PD | IEN | PTD | EN | M0))\
> +	MUX_VAL(CP(D2D_MCAD14), (OFF_IN_PD | IEN | PTD | EN | M0))\
> +	MUX_VAL(CP(D2D_MCAD15), (OFF_IN_PD | IEN | PTD | EN | M0))\
> +	MUX_VAL(CP(D2D_MCAD16), (OFF_IN_PD | IEN | PTD | EN | M0))\
> +	MUX_VAL(CP(D2D_MCAD17), (OFF_IN_PD | IEN | PTD | EN | M0))\
> +	MUX_VAL(CP(D2D_MCAD18), (OFF_IN_PD | IEN | PTD | EN | M0))\
> +	MUX_VAL(CP(D2D_MCAD19), (OFF_IN_PD | IEN | PTD | EN | M0))\
> +	MUX_VAL(CP(D2D_MCAD20), (OFF_IN_PD | IEN | PTD | EN | M0))\
> +	MUX_VAL(CP(D2D_MCAD21), (OFF_IN_PD | IEN | PTD | EN | M0))\
> +	MUX_VAL(CP(D2D_MCAD22), (OFF_IN_PD | IEN | PTD | EN | M0))\
> +	MUX_VAL(CP(D2D_MCAD23), (OFF_IN_PD | IEN | PTD | EN | M0))\
> +	MUX_VAL(CP(D2D_MCAD24), (OFF_IN_PD | IEN | PTD | EN | M0))\
> +	MUX_VAL(CP(D2D_MCAD25), (OFF_IN_PD | IEN | PTD | EN | M0))\
> +	MUX_VAL(CP(D2D_MCAD26), (OFF_IN_PD | IEN | PTD | EN | M0))\
> +	MUX_VAL(CP(D2D_MCAD27), (OFF_IN_PD | IEN | PTD | EN | M0))\
> +	MUX_VAL(CP(D2D_MCAD28), (OFF_IN_PD | IEN | PTD | EN | M0))\
> +	MUX_VAL(CP(D2D_MCAD29), (OFF_IN_PD | IEN | PTD | EN | M0))\
> +	MUX_VAL(CP(D2D_MCAD30), (OFF_IN_PD | IEN | PTD | EN | M0))\
> +	MUX_VAL(CP(D2D_MCAD31), (OFF_IN_PD | IEN | PTD | EN | M0))\
> +	MUX_VAL(CP(D2D_MCAD32), (OFF_IN_PD | IEN | PTD | EN | M0))\
> +	MUX_VAL(CP(D2D_MCAD33), (OFF_IN_PD | IEN | PTD | EN | M0))\
> +	MUX_VAL(CP(D2D_MCAD34), (OFF_IN_PD | IEN | PTD | EN | M0))\
> +	MUX_VAL(CP(D2D_MCAD35), (OFF_IN_PD | IEN | PTD | EN | M0))\
> +	MUX_VAL(CP(D2D_MCAD36), (OFF_IN_PD | IEN | PTD | EN | M0))\
> +	MUX_VAL(CP(D2D_CLK26MI), (OFF_OUT_PD | IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(D2D_NRESPWRON), (OFF_OUT_PD | IEN | PTD | EN | M0))\
> +	MUX_VAL(CP(D2D_NRESWARM), (OFF_IN_PD | IEN | PTU | EN | M0))\
> +	MUX_VAL(CP(D2D_ARM9NIRQ), (OFF_OUT_PD | IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(D2D_UMA2P6FIQ), (OFF_OUT_PD | IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(D2D_SPINT), (OFF_IN_PD | IEN | PTD | EN | M0))\
> +	MUX_VAL(CP(D2D_FRINT), (OFF_IN_PD | IEN | PTD | EN | M0))\
> +	MUX_VAL(CP(D2D_DMAREQ0), (OFF_OUT_PD | IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(D2D_DMAREQ1), (OFF_OUT_PD | IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(D2D_DMAREQ2), (OFF_OUT_PD | IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(D2D_DMAREQ3), (OFF_OUT_PD | IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(D2D_N3GTRST), (OFF_OUT_PD | IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(D2D_N3GTDI), (OFF_OUT_PD | IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(D2D_N3GTDO), (OFF_IN_PD | IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(D2D_N3GTMS), (OFF_OUT_PD | IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(D2D_N3GTCK), (OFF_OUT_PD | IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(D2D_N3GRTCK), (OFF_IN_PD | IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(D2D_MSTDBY), (OFF_IN_PD | IEN | PTU | EN | M0))\
> +	MUX_VAL(CP(D2D_SWAKEUP), (IEN | PTD | EN | M0))\
> +	MUX_VAL(CP(D2D_IDLEREQ), (OFF_OUT_PD | IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(D2D_IDLEACK), (OFF_IN_PD | IEN | PTU | EN | M0))\
> +	MUX_VAL(CP(D2D_MWRITE), (OFF_IN_PD | IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(D2D_SWRITE), (OFF_IN_PD | IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(D2D_MREAD), (OFF_IN_PD | IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(D2D_SREAD), (OFF_IN_PD | IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(D2D_MBUSFLAG), (OFF_IN_PD | IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(D2D_SBUSFLAG), (OFF_OUT_PD | IEN | PTD | DIS | M0))\
> +	MUX_VAL(CP(SDRC_CKE0), (IDIS | PTU | EN | M0))\
> +	MUX_VAL(CP(SDRC_CKE1), (IDIS | PTD | DIS | M7)) /*SDRC_CKE1 NOT USED*/
> +
> +/*
> + * GPMC Timing definitions for SDP3430
> + * at L3 = 166Mhz
> + */
> +
> +/* Timing definitions for GPMC controller for Sibley NOR */
> +#define SDP3430_NOR_GPMC_CONF1 0x00001200
> +#define SDP3430_NOR_GPMC_CONF2 0x001F1F00
> +#define SDP3430_NOR_GPMC_CONF3 0x00080802
> +#define SDP3430_NOR_GPMC_CONF4 0x1C091C09
> +#define SDP3430_NOR_GPMC_CONF5 0x01131F1F
> +#define SDP3430_NOR_GPMC_CONF6 0x1F0F03C2
> +
> +/*
> + * Timing definitions for GPMC controller for Debug Board
> + * Debug board contains access to ethernet and DIP Switch setting
> + * information etc.
> + */
> +#define SDP3430_DEBUG_GPMC_CONF1 0x00611200
> +#define SDP3430_DEBUG_GPMC_CONF2 0x001F1F01
> +#define SDP3430_DEBUG_GPMC_CONF3 0x00080803
> +#define SDP3430_DEBUG_GPMC_CONF4 0x1D091D09
> +#define SDP3430_DEBUG_GPMC_CONF5 0x041D1F1F
> +#define SDP3430_DEBUG_GPMC_CONF6 0x1D0904C4
> +
> +/* Timing defintions for GPMC OneNAND */
> +#define SDP3430_ONENAND_GPMC_CONF1 0x00001200
> +#define SDP3430_ONENAND_GPMC_CONF2 0x000F0F01
> +#define SDP3430_ONENAND_GPMC_CONF3 0x00030301
> +#define SDP3430_ONENAND_GPMC_CONF4 0x0F040F04
> +#define SDP3430_ONENAND_GPMC_CONF5 0x010F1010
> +#define SDP3430_ONENAND_GPMC_CONF6 0x1F060000
> +
> +/* GPMC definitions for GPMC NAND */
> +#define SDP3430_NAND_GPMC_CONF1 0x00000800
> +#define SDP3430_NAND_GPMC_CONF2 0x00141400
> +#define SDP3430_NAND_GPMC_CONF3 0x00141400
> +#define SDP3430_NAND_GPMC_CONF4 0x0F010F01
> +#define SDP3430_NAND_GPMC_CONF5 0x010C1414
> +#define SDP3430_NAND_GPMC_CONF6 0x1F040A80
> +
> +#endif /* _BOARD_SDP_H_ */
> diff --git a/include/configs/omap3_sdp3430.h b/include/configs/omap3_sdp3430.h
> new file mode 100644
> index 0000000..229dc5e
> --- /dev/null
> +++ b/include/configs/omap3_sdp3430.h
> @@ -0,0 +1,369 @@
> +/*
> + * (C) Copyright 2006-2009
> + * Texas Instruments Incorporated.
> + * Richard Woodruff <r-woodruff2@ti.com>
> + * Syed Mohammed Khasim <x0khasim@ti.com>
> + * Nishanth Menon <nm@ti.com>
> + *
> + * Configuration settings for the 3430 TI SDP3430 board.
> + *
> + * See file CREDITS for list of people who contributed to this
> + * project.
> + *
> + * This program is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation; either version 2 of
> + * the License, or (at your option) any later version.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
> + * GNU General Public License for more details.
> + *
> + * You should have received a copy of the GNU General Public License
> + * along with this program; if not, write to the Free Software
> + * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
> + * MA 02111-1307 USA
> + */
> +
> +#ifndef __CONFIG_H
> +#define __CONFIG_H
> +
> +/* TODO: REMOVE THE FOLLOWING
> + * Retained the following till size.h is removed in u-boot
> + */
> +#include <asm/sizes.h>
> +/*
> + * High Level Configuration Options
> + */
> +#define CONFIG_ARMCORTEXA8	1	/* This is an ARM V7 CPU core */
> +#define CONFIG_OMAP		1	/* in a TI OMAP core */
> +#define CONFIG_OMAP34XX		1	/* which is a 34XX */
> +#define CONFIG_OMAP3430		1	/* which is in a 3430 */
> +#define CONFIG_OMAP3_3430SDP	1	/* working with SDP Rev2 */
> +
> +#include <asm/arch/cpu.h>		/* get chip and board defs */
> +#include <asm/arch/omap3.h>
> +
> +/*
> + * NOTE:  these #defines presume standard SDP jumper settings.
> + * In particular:
> + *  - 26 MHz clock (not 19.2 or 38.4 MHz)
> + *  - Boot from 128MB NOR, not NAND or OneNAND
> + *
> + * At this writing, OMAP3 U-Boot support doesn't permit concurrent
> + * support for all the flash types the board supports.
> + */
> +#define CONFIG_DISPLAY_CPUINFO		1
> +#define CONFIG_DISPLAY_BOARDINFO	1
> +
> +/* Clock Defines */
> +#define V_OSCK			26000000	/* Clock output from T2 */
> +#define V_SCLK			(V_OSCK >> 1)
> +
> +#undef CONFIG_USE_IRQ			/* no support for IRQs */
> +#define CONFIG_MISC_INIT_R
> +
> +#define CONFIG_CMDLINE_TAG		1	/* enable passing of ATAGs */
> +#define CONFIG_SETUP_MEMORY_TAGS	1
> +#define CONFIG_INITRD_TAG		1
> +#define CONFIG_REVISION_TAG		1
> +
> +/*
> + * Size of malloc() pool
> + * Total Size Environment - 256k
> + * Malloc - add 256k
> + */
> +#define CONFIG_ENV_SIZE			(256 << 10)
> +#define CONFIG_SYS_MALLOC_LEN		(CONFIG_ENV_SIZE + (256 << 10))
> +#define CONFIG_SYS_GBL_DATA_SIZE	128	/* bytes reserved for */
> +						/* initial data */
> +
> +/*--------------------------------------------------------------------------*/
> +
> +/*
> + * Hardware drivers
> + */
> +
> +/*
> + * TWL4030
> + */
> +#define CONFIG_TWL4030_POWER		1
> +
> +/*
> + * serial port - NS16550 compatible
> + */
> +#define V_NS16550_CLK			48000000	/* 48MHz (APLL96/2) */
> +
> +#define CONFIG_SYS_NS16550
> +#define CONFIG_SYS_NS16550_SERIAL
> +#define CONFIG_SYS_NS16550_REG_SIZE	(-4)
> +#define CONFIG_SYS_NS16550_CLK		V_NS16550_CLK
> +
> +/* Original SDP u-boot used UART1 and thus J8 (innermost); that can be
> + * swapped with UART2 via jumpering.  Downsides of using J8:  it doesn't
> + * support UART boot (that's only for UART3); it prevents sharing a Linux
> + * kernel (LL_DEBUG_UART3) or filesystem (getty ttyS2) with most boards.
> + *
> + * UART boot uses UART3 on J9, and the SDP user's guide says to use
> + * that for console.  Downsides of using J9:  you can't use IRDA too;
> + * since UART3 isn't in the CORE power domain, it may be a bit less
> + * usable in certain PM-sensitive debug scenarios.
> + */
> +#undef CONSOLE_J9			/* else J8/UART1 (innermost) */
> +
> +#ifdef CONSOLE_J9
> +#define CONFIG_CONS_INDEX		3
> +#define CONFIG_SYS_NS16550_COM3		OMAP34XX_UART3
> +#define CONFIG_SERIAL3			3	/* UART3 */
> +#else
> +#define CONFIG_CONS_INDEX		1
> +#define CONFIG_SYS_NS16550_COM1		OMAP34XX_UART1
> +#define CONFIG_SERIAL1			1	/* UART1 */
> +#endif
> +
> +#define CONFIG_ENV_OVERWRITE
> +#define CONFIG_BAUDRATE			115200
> +#define CONFIG_SYS_BAUDRATE_TABLE	{4800, 9600, 19200, 38400, 57600,\
> +					115200}
> +
> +/*
> + * I2C for power management setup
> + */
> +#define CONFIG_HARD_I2C			1
> +#define CONFIG_SYS_I2C_SPEED		100000
> +#define CONFIG_SYS_I2C_SLAVE		1
> +#define CONFIG_SYS_I2C_BUS		0
> +#define CONFIG_SYS_I2C_BUS_SELECT	1
> +#define CONFIG_DRIVER_OMAP34XX_I2C	1
> +
> +/* OMITTED:  single 1 Gbit MT29F1G NAND flash */
> +
> +/*
> + * NOR boot support - single 1 Gbit PF48F6000M0 Strataflash
> + */
> +#define CONFIG_SYS_FLASH_BASE		0x10000000
> +#define CONFIG_FLASH_CFI_DRIVER		1	/* Use drivers/cfi_flash.c */
> +#define CONFIG_SYS_FLASH_CFI		1	/* use CFI geometry data */
> +#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1	/* ~10x faster writes */
> +#define CONFIG_SYS_FLASH_PROTECTION	1	/* hardware sector protection */
> +#define CONFIG_SYS_FLASH_EMPTY_INFO	1	/* flinfo 'E' for empty */
> +#define CONFIG_SYS_FLASH_BANKS_LIST     {CONFIG_SYS_FLASH_BASE}
> +#define CONFIG_SYS_MAX_FLASH_BANKS      1	/* max number of flash banks */
> +
> +#define CONFIG_SYS_FLASH_CFI_WIDTH	2
> +#define PHYS_FLASH_SIZE			(128 << 20)
> +#define CONFIG_SYS_MAX_FLASH_SECT	512	/* max sectors on one chip */
> +
> +/* timeout values are in milliseconds */
> +#define CONFIG_SYS_FLASH_ERASE_TOUT	(100 * CONFIG_SYS_HZ)
> +#define CONFIG_SYS_FLASH_WRITE_TOUT	(100 * CONFIG_SYS_HZ)
> +
> +/* OMITTED:  single 2 Gbit KFM2G16 OneNAND flash */
> +
> +#define CONFIG_ENV_IS_IN_FLASH		1
> +#define CONFIG_SYS_ENV_SECT_SIZE	(256 << 10)
> +#define CONFIG_ENV_OFFSET		CONFIG_SYS_ENV_SECT_SIZE
> +#define CONFIG_ENV_ADDR	(CONFIG_SYS_FLASH_BASE + CONFIG_SYS_ENV_SECT_SIZE)
> +/*--------------------------------------------------------------------------*/
> +
> +/* commands to include */
> +#include <config_cmd_default.h>
> +
> +/* Enabled commands */
> +#define CONFIG_CMD_DHCP		/* DHCP Support			*/
> +#define CONFIG_CMD_EXT2		/* EXT2 Support			*/
> +#define CONFIG_CMD_FAT		/* FAT support			*/
> +#define CONFIG_CMD_I2C		/* I2C serial bus support	*/
> +#define CONFIG_CMD_JFFS2	/* JFFS2 Support		*/
> +#define CONFIG_CMD_MMC		/* MMC support			*/
> +#define CONFIG_CMD_NET
> +
> +/* Disabled commands */
> +#undef CONFIG_CMD_FPGA		/* FPGA configuration Support	*/
> +#undef CONFIG_CMD_IMLS		/* List all found images	*/
> +
> +/*--------------------------------------------------------------------------*/
> +/*
> + * MMC boot support
> + */
> +
> +#if defined(CONFIG_CMD_MMC)
> +#define CONFIG_MMC			1
> +#define CONFIG_OMAP3_MMC		1
> +#define CONFIG_DOS_PARTITION		1
> +#endif
> +
> +/*----------------------------------------------------------------------------
> + * SMSC9115 Ethernet from SMSC9118 family
> + *----------------------------------------------------------------------------
> + */
> +#if defined(CONFIG_CMD_NET)
> +
> +#define CONFIG_DRIVER_LAN91C96
> +#define CONFIG_LAN91C96_BASE	DEBUG_BASE
> +#define CONFIG_LAN91C96_EXT_PHY
> +
> +#define CONFIG_BOOTP_SEND_HOSTNAME
> +/*
> + * BOOTP fields
> + */
> +#define CONFIG_BOOTP_SUBNETMASK		0x00000001
> +#define CONFIG_BOOTP_GATEWAY		0x00000002
> +#define CONFIG_BOOTP_HOSTNAME		0x00000004
> +#define CONFIG_BOOTP_BOOTPATH		0x00000010
> +#endif /* (CONFIG_CMD_NET) */
> +
> +/*
> + * Environment setup
> + *
> + * Default boot order:  mmc bootscript, MMC uImage, NOR image.
> + * Network booting environment must be configured at site.
> + */
> +
> +/* allow overwriting serial config and ethaddr */
> +#define CONFIG_ENV_OVERWRITE
> +
> +#define CONFIG_EXTRA_ENV_SETTINGS \
> +	"loadaddr=0x82000000\0" \
> +	"console=ttyS0,115200n8\0" \
> +	"mmcargs=setenv bootargs console=${console} " \
> +		"root=/dev/mmcblk0p2 rw " \
> +		"rootfstype=ext3 rootwait\0" \
> +	"norargs=setenv bootargs console=${console} " \
> +		"root=/dev/mtdblock3 rw " \
> +		"rootfstype=jffs2\0" \
> +	"loadbootscript=fatload mmc 0 ${loadaddr} boot.scr\0" \
> +	"bootscript=echo Running bootscript from MMC/SD ...; " \
> +		"autoscr ${loadaddr}\0" \
> +	"loaduimage=fatload mmc 0 ${loadaddr} uImage\0" \
> +	"mmcboot=echo Booting from MMC/SD ...; " \
> +		"run mmcargs; " \
> +		"bootm ${loadaddr}\0" \
> +	"norboot=echo Booting from NOR ...; " \
> +		"run norargs; " \
> +		"bootm 0x80000\0" \
> +
> +#define CONFIG_BOOTCOMMAND \
> +	"if mmcinit; then " \
> +		"if run loadbootscript; then " \
> +			"run bootscript; " \
> +		"else " \
> +			"if run loaduimage; then " \
> +				"run mmcboot; " \
> +			"else run norboot; " \
> +			"fi; " \
> +		"fi; " \
> +	"else run norboot; fi"
> +
> +#define CONFIG_AUTO_COMPLETE		1
> +
> +/*--------------------------------------------------------------------------*/
> +
> +/*
> + * Miscellaneous configurable options
> + */
> +#define V_PROMPT			"OMAP34XX SDP # "
> +
> +#define CONFIG_SYS_LONGHELP		/* undef to save memory */
> +#define CONFIG_SYS_HUSH_PARSER		/* use "hush" command parser */
> +#define CONFIG_SYS_PROMPT_HUSH_PS2	"> "
> +#define CONFIG_SYS_PROMPT		V_PROMPT
> +#define CONFIG_SYS_CBSIZE		256	/* Console I/O Buffer Size */
> +/* Print Buffer Size */
> +#define CONFIG_SYS_PBSIZE		(CONFIG_SYS_CBSIZE + \
> +					sizeof(CONFIG_SYS_PROMPT) + 16)
> +#define CONFIG_SYS_MAXARGS		16	/* max number of command args */
> +/* Boot Argument Buffer Size */
> +#define CONFIG_SYS_BARGSIZE		(CONFIG_SYS_CBSIZE)
> +
> +/* SDRAM Test range - start at 16 meg boundary -ends at 32Meg -
> + * a basic sanity check ONLY
> + * IF you would like to increase coverage, increase the end address
> + * or run the test with custom options
> + */
> +#define CONFIG_SYS_MEMTEST_START	(OMAP34XX_SDRC_CS0 + 0x01000000)
> +#define CONFIG_SYS_MEMTEST_END		(OMAP34XX_SDRC_CS0 + (32 << 20))
> +
> +/* Default load address */
> +#define CONFIG_SYS_LOAD_ADDR		(OMAP34XX_SDRC_CS0)
> +
> +/*--------------------------------------------------------------------------*/
> +
> +/*
> + * 3430 has 12 GP timers, they can be driven by the SysClk (12/13/19.2) or by
> + * 32KHz clk, or from external sig. This rate is divided by a local divisor.
> + */
> +#define CONFIG_SYS_TIMERBASE		(OMAP34XX_GPT2)
> +#define CONFIG_SYS_PTV			2	/* Divisor: 2^(PTV+1) => 8 */
> +#define CONFIG_SYS_HZ			1000
> +
> +/*
> + * Stack sizes
> + *
> + * The stack sizes are set up in start.S using the settings below
> + */
> +#define CONFIG_STACKSIZE	(128 << 10) /* Regular stack */
> +#ifdef CONFIG_USE_IRQ
> +#define CONFIG_STACKSIZE_IRQ	(4 << 10) /* IRQ stack */
> +#define CONFIG_STACKSIZE_FIQ	(4 << 10) /* FIQ stack */
> +#endif
> +
> +/*
> + * SDRAM Memory Map
> + */
> +#define CONFIG_NR_DRAM_BANKS	2	/* CS1 may or may not be populated */
> +#define PHYS_SDRAM_1		OMAP34XX_SDRC_CS0
> +#define PHYS_SDRAM_1_SIZE	(32 << 20) /*@least 32 meg */
> +#define PHYS_SDRAM_2		OMAP34XX_SDRC_CS1
> +
> +/* SDRAM Bank Allocation method */
> +#define SDRC_R_B_C		1
> +
> +/*--------------------------------------------------------------------------*/
> +
> +/*
> + * NOR FLASH usage ... default nCS0:
> + *  - one 256KB sector for U-Boot
> + *  - one 256KB sector for its parameters (not all used)
> + *  - eight sectors (2 MB) for kernel
> + *  - rest for JFFS2
> + */
> +
> +/* Monitor at start of flash */
> +#define CONFIG_SYS_MONITOR_BASE		CONFIG_SYS_FLASH_BASE
> +#define CONFIG_SYS_MONITOR_LEN		(256 << 10)
> +
> +#define CONFIG_SYS_JFFS2_FIRST_BANK	CONFIG_SYS_MAX_FLASH_BANKS
> +#define CONFIG_SYS_JFFS2_NUM_BANKS	1
> +
> +/*
> + * NAND FLASH usage ... default nCS1:
> + *  - four 128KB sectors for X-Loader
> + *  - four 128KB sectors for U-Boot
> + *  - two 128KB sector for its parameters
> + *  - 32 sectors (4 MB) for kernel
> + *  - rest for filesystem
> + */
> +
> +/*
> + * OneNAND FLASH usage ... default nCS2:
> + *  - four 128KB sectors for X-Loader
> + *  - two 128KB sectors for U-Boot
> + *  - one 128KB sector for its parameters
> + *  - sixteen sectors (2 MB) for kernel
> + *  - rest for filesystem
> + */
> +
> +/*--------------------------------------------------------------------------*/
> +
> +#ifndef __ASSEMBLY__
> +extern struct gpmc *gpmc_cfg;
> +extern unsigned int boot_flash_base;
> +extern volatile unsigned int boot_flash_env_addr;
> +extern unsigned int boot_flash_off;
> +extern unsigned int boot_flash_sec;
> +extern unsigned int boot_flash_type;
> +#endif
> +
> +#endif				/* __CONFIG_H */