[PATCH] MIPS: Alchemy: fix hang with high-frequency edge interrupts

[Manuel Lauss <manuel.lauss@googlemail.com>]

The handle_edge_irq() flowhandler disables edge int sources which occur
too fast (i.e. another edge comes in before the irq handler function
had a chance to finish).  Currently, the mask_ack() callback does not
ack the edges in hardware, leading to an endless loop in the flowhandler
where it tries to shut up the irq source.

When I rewrote the alchemy IRQ code  I wrongly assumed the mask_ack()
callback was only used by the level flowhandler, hence it omitted the
(at the time pointless) edge acks.  Turned out I was wrong; so here
is a complete mask_ack implementation for Alchemy IC, which fixes
the above mentioned problem.

Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
---
Can be easily triggered with a simple not-debounced switch attached to
an edge-triggered gpio.

 arch/mips/alchemy/common/irq.c |   34 ++++++++++++++++++++++++++--------
 1 files changed, 26 insertions(+), 8 deletions(-)

diff --git a/arch/mips/alchemy/common/irq.c b/arch/mips/alchemy/common/irq.c
index c88c821..d670928 100644
--- a/arch/mips/alchemy/common/irq.c
+++ b/arch/mips/alchemy/common/irq.c
@@ -354,6 +354,28 @@ static void au1x_ic1_ack(unsigned int irq_nr)
 	au_sync();
 }

+static void au1x_ic0_maskack(unsigned int irq_nr)
+{
+	unsigned int bit = irq_nr - AU1000_INTC0_INT_BASE;
+
+	au_writel(1 << bit, IC0_WAKECLR);
+	au_writel(1 << bit, IC0_MASKCLR);
+	au_writel(1 << bit, IC0_RISINGCLR);
+	au_writel(1 << bit, IC0_FALLINGCLR);
+	au_sync();
+}
+
+static void au1x_ic1_maskack(unsigned int irq_nr)
+{
+	unsigned int bit = irq_nr - AU1000_INTC1_INT_BASE;
+
+	au_writel(1 << bit, IC1_WAKECLR);
+	au_writel(1 << bit, IC1_MASKCLR);
+	au_writel(1 << bit, IC1_RISINGCLR);
+	au_writel(1 << bit, IC1_FALLINGCLR);
+	au_sync();
+}
+
 static int au1x_ic1_setwake(unsigned int irq, unsigned int on)
 {
 	unsigned int bit = irq - AU1000_INTC1_INT_BASE;
@@ -379,25 +401,21 @@ static int au1x_ic1_setwake(unsigned int irq, unsigned int on)
 /*
  * irq_chips for both ICs; this way the mask handlers can be
  * as short as possible.
- *
- * NOTE: the ->ack() callback is used by the handle_edge_irq
- *	 flowhandler only, the ->mask_ack() one by handle_level_irq,
- *	 so no need for an irq_chip for each type of irq (level/edge).
  */
 static struct irq_chip au1x_ic0_chip = {
 	.name		= "Alchemy-IC0",
-	.ack		= au1x_ic0_ack,		/* edge */
+	.ack		= au1x_ic0_ack,
 	.mask		= au1x_ic0_mask,
-	.mask_ack	= au1x_ic0_mask,	/* level */
+	.mask_ack	= au1x_ic0_maskack,
 	.unmask		= au1x_ic0_unmask,
 	.set_type	= au1x_ic_settype,
 };

 static struct irq_chip au1x_ic1_chip = {
 	.name		= "Alchemy-IC1",
-	.ack		= au1x_ic1_ack,		/* edge */
+	.ack		= au1x_ic1_ack,
 	.mask		= au1x_ic1_mask,
-	.mask_ack	= au1x_ic1_mask,	/* level */
+	.mask_ack	= au1x_ic1_maskack,
 	.unmask		= au1x_ic1_unmask,
 	.set_type	= au1x_ic_settype,
 	.set_wake	= au1x_ic1_setwake,
-- 
1.6.5