Re: saa7134 (not very) new board 5168:0307

["tomlohave@gmail.com" <tomlohave@gmail.com>]

Hi hermann,

we are this results :

with

&tda827x_cfg_0, &tda827x_cfg_1 or &tda827x_cfg_2

we have a perfect image without sound on the analogic part (test with mplayer),
a partial result with dvb-t : we need to initialize first with analogic (with cold boot, the card doesn't work on dvb)
but only for few seconds(sound and image are ok) 
then re-initialize with analogic, work for few seconds on dvb and then nothing
maybe i am wrong but, the sound part for analogic is a problem of redirection, isn't it  ?

here are our configuration for this card :

in saa7134-dvb.c

static struct tda1004x_config tda827x_flydvbtduo_medion_config = {
	.demod_address = 0x08,
	.invert        = 1,
	.invert_oclk   = 0,
	.xtal_freq     = TDA10046_XTAL_16M,
	.agc_config    = TDA10046_AGC_TDA827X,
	.gpio_config   = TDA10046_GP01_I,
	.if_freq       = TDA10046_FREQ_045,
	.i2c_gate      = 0x4b,
	.tuner_address = 0x61,
	.antenna_switch = 2,
	.request_firmware = philips_tda1004x_request_firmware
};

case SAA7134_BOARD_FLYDVBTDUO_MEDION:
		if (configure_tda827x_fe(dev, &tda827x_flydvbtduo_medion_config,
					 &tda827x_cfg_2) < 0)
			goto dettach_frontend;
		break;
	default:
		wprintk("Huh? unknown DVB card?\n");
		break;


in saa7134-cards.c

    [SAA7134_BOARD_FLYDVBTDUO_MEDION] = {
        .name           = "LifeView FlyDVB-T DUO Medion",
        .audio_clock    = 0x00187de7,
        .tuner_type     = TUNER_PHILIPS_TDA8290,
        .radio_type     = UNSET,
        .tuner_addr    = ADDR_UNSET,
        .radio_addr    = ADDR_UNSET,
        .gpiomask    = 0x00200000,
        .mpeg           = SAA7134_MPEG_DVB,
        .inputs         = {{
            .name = name_tv,
            .vmux = 1,
            .amux = TV,
            .gpio = 0x200000,     /* GPIO21=High for TV input */
            .tv   = 1,
        },{
            .name = name_comp1,    /* Composite signal on S-Video input */
            .vmux = 3,
            .amux = LINE1,
        },{
            .name = name_svideo,    /* S-Video signal on S-Video input */
            .vmux = 8,
            .amux = LINE1,
        }},
        .radio = {
            .name = name_radio,
            .amux = TV,
            .gpio = 0x000000,    /* GPIO21=Low for FM radio antenna */
        },


.vendor       = PCI_VENDOR_ID_PHILIPS,
        .device       = PCI_DEVICE_ID_PHILIPS_SAA7133,
        .subvendor    = 0x5168,        
        .subdevice    = 0x0307,  /* LR307-N */      
        .driver_data  = SAA7134_BOARD_FLYDVBTDUO_MEDION,

case SAA7134_BOARD_FLYDVBTDUO_MEDION:
    {
        /* this is a hybrid board, initialize to analog mode
         * and configure firmware eeprom address
         */
        u8 data[] = { 0x3c, 0x33, 0x60};
        struct i2c_msg msg = {.addr=0x08, .flags=0, .buf=data, .len = 
sizeof(data)};
        i2c_transfer(&dev->i2c_adap, &msg, 1);
        break;




What can we do to have dvb fully supported ?

thanks in advance,

Cheers,

Thomas