From mboxrd@z Thu Jan 1 00:00:00 1970 From: Bill Gatliff Subject: Re: Anyone using an ISP1505? Date: Fri, 18 Dec 2009 13:13:59 -0600 Message-ID: <4B2BD477.4080105@billgatliff.com> References: <4B2A7FFB.6090909@billgatliff.com> <20091217191005.GA30191@nokia.com> Mime-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: QUOTED-PRINTABLE Return-path: Received: from mail-gx0-f211.google.com ([209.85.217.211]:59904 "EHLO mail-gx0-f211.google.com" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S1753908AbZLRTNu (ORCPT ); Fri, 18 Dec 2009 14:13:50 -0500 Received: by gxk3 with SMTP id 3so2336827gxk.1 for ; Fri, 18 Dec 2009 11:13:49 -0800 (PST) In-Reply-To: <20091217191005.GA30191@nokia.com> Sender: linux-omap-owner@vger.kernel.org List-Id: linux-omap@vger.kernel.org To: felipe.balbi@nokia.com Cc: "linux-omap@vger.kernel.org" , "beagleboard@googlegroups.com" =46elipe Balbi wrote: > > is this with musb ? if it's musb, you need the nop transceiver. Do yo= u > have any boot logs which you could share ? Without information on the > board, is a bit difficult :-( Of course. Here is an excerpt from my dmesg output: Linux version 2.6.33-rc1-06888-g7fa9fb6-dirty (bgat@mercury) (gcc version 4.3.2 (Debian 4.3.2-1.1) ) #22 Fri Dec 18 18:58:00 UTC 2009 =20 CPU: ARMv7 Processor [411fc083] revision 3 (ARMv7), cr=3D10c53c7f =20 CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache =20 Machine: TBD Memory policy: ECC disabled, Data cache writeback =20 On node 0 totalpages: 32768 = =20 free_area_init_node: node 0, pgdat c0467a3c, node_mem_map c0485000 =20 Normal zone: 256 pages used for memmap =20 Normal zone: 0 pages reserved = =20 Normal zone: 32512 pages, LIFO batch:7 =20 OMAP3430/3530 ES3.0 (l2cache iva sgx neon isp ) =20 SRAM: Mapped pa 0x40200000 to va 0xfe400000 size: 0x100000 =20 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512 =20 Kernel command line: root=3Dnfs nfsroot=3D192.168.2.10:/exports/tbd rw ip=3D192.168.2.168:192.168.2.10:192.168.2.1:255.255.255.0:tbd:eth0:off console=3DttyS1,115200n8 =20 PID hash table entries: 512 (order: -1, 2048 bytes) =20 Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) =20 Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) =20 Memory: 128MB =3D 128MB total = =20 Memory: 125168KB available (3992K code, 310K data, 164K init, 0K highmem) =20 Hierarchical RCU implementation. = =20 RCU-based detection of stalled CPUs is enabled. =20 NR_IRQS:388 = =20 Clocking rate (Crystal/Core/MPU): 19.2/332/545 MHz =20 Reprogramming SDRC clock to 332000000 Hz =20 GPMC revision 5.0 = =20 IRQ: Found an INTC at 0xfa200000 (revision 4.0) with 96 interrupts =20 Total of 96 interrupts on 1 active controller =20 OMAP GPIO hardware version 2.5 = =20 OMAP clockevent source: GPTIMER12 at 32768 Hz =20 Console: colour dummy device 80x30 =20 Calibrating delay loop... 524.12 BogoMIPS (lpj=3D2048000) =20 Mount-cache hash table entries: 512 =20 CPU: Testing write buffer coherency: ok =20 NET: Registered protocol family 16 =20 mux: Setting signal mcbsp_clks.mcbsp_clks 0x0100 -> 0x0100 =20 mux: Setting signal mcbsp2_fsx.mcbsp2_fsx 0x0018 -> 0x0100 =20 mux: Setting signal mcbsp2_clkx.mcbsp2_clkx 0x0018 -> 0x0100 =20 mux: Setting signal mcbsp2_dx.mcbsp2_dx 0x0018 -> 0x0000 =20 mux: Setting signal mcbsp2_dr.mcbsp2_dr 0x0100 -> 0x0100 =20 mux: Setting signal i2c1_scl.i2c1_scl 0x0118 -> 0x0118 =20 mux: Setting signal i2c1_sda.i2c1_sda 0x0118 -> 0x0118 =20 mux: Setting signal sys_clkout1.sys_clkout1 0x0100 -> 0x0000 =20 mux: Setting signal hsusb0_clk.hsusb0_clk 0x0100 -> 0x0000 =20 mux: Setting signal hsusb0_stp.hsusb0_stp 0x0018 -> 0x0000 =20 mux: Setting signal hsusb0_dir.hsusb0_dir 0x0100 -> 0x0100 =20 mux: Setting signal hsusb0_nxt.hsusb0_nxt 0x0100 -> 0x0100 =20 mux: Setting signal hsusb0_data0.hsusb0_data0 0x0100 -> 0x0100 =20 mux: Setting signal hsusb0_data1.hsusb0_data1 0x0100 -> 0x0100 =20 mux: Setting signal hsusb0_data2.hsusb0_data2 0x0100 -> 0x0100 =20 mux: Setting signal hsusb0_data3.hsusb0_data3 0x0100 -> 0x0100 =20 mux: Setting signal hsusb0_data4.hsusb0_data4 0x0100 -> 0x0100 =20 mux: Setting signal hsusb0_data5.hsusb0_data5 0x0100 -> 0x0100 =20 mux: Setting signal hsusb0_data6.hsusb0_data6 0x0100 -> 0x0100 =20 mux: Setting signal hsusb0_data7.hsusb0_data7 0x0100 -> 0x0100 =20 mux: Setting signal mcbsp3_dx.gpio140 0x0004 -> 0x0004 =20 mux: Setting signal etk_clk.hsusb1_stp 0x0018 -> 0x0003 =20 mux: Setting signal etk_ctl.hsusb1_clk 0x0000 -> 0x0003 =20 mux: Setting signal etk_d8.hsusb1_dir 0x0100 -> 0x010b =20 mux: Setting signal etk_d9.hsusb1_nxt 0x0100 -> 0x010b =20 mux: Setting signal etk_d0.hsusb1_data0 0x0100 -> 0x010b =20 mux: Setting signal etk_d1.hsusb1_data1 0x0100 -> 0x010b =20 mux: Setting signal etk_d2.hsusb1_data2 0x0108 -> 0x010b =20 mux: Setting signal etk_d7.hsusb1_data3 0x0100 -> 0x010b =20 mux: Setting signal etk_d4.hsusb1_data4 0x0100 -> 0x010b =20 mux: Setting signal etk_d5.hsusb1_data5 0x0100 -> 0x010b =20 mux: Setting signal etk_d6.hsusb1_data6 0x0100 -> 0x010b =20 mux: Setting signal etk_d3.hsusb1_data7 0x0100 -> 0x010b =20 mux: Setting signal etk_d11.hsusb2_stp 0x0100 -> 0x0003 =20 mux: Setting signal etk_d10.hsusb2_clk 0x0100 -> 0x0003 =20 mux: Setting signal etk_d12.hsusb2_dir 0x0100 -> 0x010b =20 mux: Setting signal etk_d13.hsusb2_nxt 0x0100 -> 0x010b =20 mux: Setting signal etk_d14.hsusb2_data0 0x0100 -> 0x010b =20 mux: Setting signal etk_d15.hsusb2_data1 0x0100 -> 0x010b =20 mux: Setting signal mcspi1_cs3.hsusb2_data2 0x011f -> 0x010b =20 mux: Setting signal mcspi2_cs1.hsusb2_data3 0x011c -> 0x010b =20 mux: Setting signal mcspi2_simo.hsusb2_data4 0x010f -> 0x010b =20 mux: Setting signal mcspi2_somi.hsusb2_data5 0x010f -> 0x010b =20 mux: Setting signal mcspi2_cs0.hsusb2_data6 0x011f -> 0x010b =20 mux: Setting signal mcspi2_clk.hsusb2_data7 0x010f -> 0x010b =20 OMAP DMA hardware revision 4.0 = =20 bio: create slab at 0 =20 SCSI subsystem initialized = =20 omap2_mcspi omap2_mcspi.1: registered master spi1 =20 omap2_mcspi omap2_mcspi.2: registered master spi2 =20 omap2_mcspi omap2_mcspi.3: registered master spi3 =20 omap2_mcspi omap2_mcspi.4: registered master spi4 =20 usbcore: registered new interface driver usbfs =20 usbcore: registered new interface driver hub =20 usbcore: registered new device driver usb =20 i2c_omap i2c_omap.1: bus 1 rev3.12 at 100 kHz =20 Switching to clocksource 32k_counter = =20 musb_hdrc: version 6.0, musb-dma, host, debug=3D0 =20 musb_hdrc: ConfigData=3D0xde (UTMI-8, dyn FIFOs, bulk combine (X), bulk split (X), HB-ISO Rx, HB-ISO Tx, SoftConn) = =20 musb_hdrc: MHDRC RTL version 1.400 =20 musb_hdrc: setup fifo_mode 4 = =20 musb_hdrc: 28/31 max ep, 16384/16384 memory =20 musb_hdrc: USB Host mode controller at fa0ab000 using DMA, IRQ 92 =20 musb_hdrc musb_hdrc: MUSB HDRC host driver =20 musb_hdrc musb_hdrc: new USB bus registered, assigned bus number 1 =20 usb usb1: default language 0x0409 = =20 usb usb1: udev 1, busnum 1, minor =3D 0 =20 usb usb1: New USB device found, idVendor=3D1d6b, idProduct=3D0002 =20 usb usb1: New USB device strings: Mfr=3D3, Product=3D2, SerialNumber=3D1 =20 usb usb1: Product: MUSB HDRC host driver =20 usb usb1: Manufacturer: Linux 2.6.33-rc1-06888-g7fa9fb6-dirty musb-hcd =20 usb usb1: SerialNumber: musb_hdrc = =20 usb usb1: uevent = =20 usb usb1: usb_probe_device = =20 usb usb1: configuration #1 chosen from 1 choice =20 usb usb1: adding 1-0:1.0 (config #1, interface 0) =20 usb 1-0:1.0: uevent = =20 hub 1-0:1.0: usb_probe_interface = =20 hub 1-0:1.0: usb_probe_interface - got id =20 hub 1-0:1.0: USB hub found = =20 hub 1-0:1.0: 1 port detected = =20 hub 1-0:1.0: standalone hub = =20 hub 1-0:1.0: individual port power switching =20 hub 1-0:1.0: no over-current protection =20 hub 1-0:1.0: power on to power good time: 10ms =20 hub 1-0:1.0: 100mA bus power budget for each child =20 hub 1-0:1.0: local power source is good =20 hub 1-0:1.0: enabling power on all ports =20 NET: Registered protocol family 2 =20 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) =20 TCP established hash table entries: 4096 (order: 3, 32768 bytes) =20 TCP bind hash table entries: 4096 (order: 2, 16384 bytes) =20 TCP: Hash tables configured (established 4096 bind 4096) =20 TCP reno registered = =20 UDP hash table entries: 256 (order: 0, 4096 bytes) =20 UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) =20 NET: Registered protocol family 1 =20 RPC: Registered udp transport module. =20 RPC: Registered tcp transport module. =20 RPC: Registered tcp NFSv4.1 backchannel transport module. =20 NetWinder Floating Point Emulator V0.97 (double precision) =20 VFS: Disk quotas dquot_6.5.2 = =20 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) =20 JFFS2 version 2.2. (NAND) =A9 2001-2006 Red Hat, Inc. =20 msgmni has been set to 244 = =20 alg: No test for stdrng (krng) = =20 io scheduler noop registered = =20 io scheduler deadline registered = =20 io scheduler cfq registered (default) =20 Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled =20 serial8250.0: ttyS0 at MMIO 0x4806a000 (irq =3D 72) is a ST16654 =20 serial8250.1: ttyS1 at MMIO 0x4806c000 (irq =3D 73) is a ST16654 =20 console [ttyS1] enabled = =20 hub 1-0:1.0: state 7 ports 1 chg 0000 evt 0000 =20 serial8250.2: ttyS2 at MMIO 0x49020000 (irq =3D 74) is a ST16654 =20 brd: module loaded = =20 loop: module loaded = =20 PPP generic driver version 2.4.2 = =20 PPP Deflate Compression module registered =20 PPP BSD Compression module registered = =20 NET: Registered protocol family 24 =20 smsc911x: Driver version 2008-10-21. = =20 smsc911x-mdio: probed = =20 eth0: attached PHY driver [SMSC LAN8700] (mii_bus:phy_addr=3Dffffffff:0= 1, irq=3D-1) =20 net eth0: MAC Address: 46:66:17:ff:76:af = =20 console [netcon0] enabled = =20 netconsole: network logging started =20 ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver =20 ehci_hcd: block sizes: qh 60 qtd 96 itd 160 sitd 96 =20 ehci-omap ehci-omap.0: starting TI EHCI USB Controller =20 ehci-omap ehci-omap.0: TLL RESET DONE =20 ehci-omap ehci-omap.0: OMAP3 ES version > ES2.1 =20 ehci-omap ehci-omap.0: UHH setup done, uhh_hostconfig=3D31c =20 ehci-omap ehci-omap.0: OMAP-EHCI Host Controller =20 ehci-omap ehci-omap.0: new USB bus registered, assigned bus number 2 =20 ehci-omap ehci-omap.0: park 0 =20 ehci-omap ehci-omap.0: irq 77, io mem 0x48064800 =20 ehci-omap ehci-omap.0: reset command 090b02 park=3D3 ithresh=3D9 period= =3D1024 Reset HALT =20 ehci-omap ehci-omap.0: init command 010009 (park)=3D0 ithresh=3D1 perio= d=3D256 RUN =20 ehci-omap ehci-omap.0: USB 2.0 started, EHCI 1.00 =20 usb usb2: default language 0x0409 = =20 usb usb2: udev 1, busnum 2, minor =3D 128 =20 usb usb2: New USB device found, idVendor=3D1d6b, idProduct=3D0002 =20 usb usb2: New USB device strings: Mfr=3D3, Product=3D2, SerialNumber=3D1 =20 usb usb2: Product: OMAP-EHCI Host Controller =20 usb usb2: Manufacturer: Linux 2.6.33-rc1-06888-g7fa9fb6-dirty ehci_hcd =20 usb usb2: SerialNumber: ehci-omap.0 = =20 usb usb2: uevent = =20 usb usb2: usb_probe_device = =20 usb usb2: configuration #1 chosen from 1 choice =20 usb usb2: adding 2-0:1.0 (config #1, interface 0) =20 usb 2-0:1.0: uevent = =20 hub 2-0:1.0: usb_probe_interface = =20 hub 2-0:1.0: usb_probe_interface - got id =20 hub 2-0:1.0: USB hub found = =20 hub 2-0:1.0: 3 ports detected = =20 hub 2-0:1.0: standalone hub = =20 hub 2-0:1.0: individual port power switching =20 hub 2-0:1.0: individual port over-current protection =20 hub 2-0:1.0: power on to power good time: 20ms =20 hub 2-0:1.0: local power source is good =20 hub 2-0:1.0: enabling power on all ports i2c /dev entries driver OMAP Watchdog Timer Rev 0x31: initial timeout 60 sec Advanced Linux Sound Architecture Driver Version 1.0.21. No device for DAI omap-mcbsp-dai-0 No device for DAI omap-mcbsp-dai-1 No device for DAI omap-mcbsp-dai-2 No device for DAI omap-mcbsp-dai-3 No device for DAI omap-mcbsp-dai-4 asoc: WM8731 <-> omap-mcbsp-dai-0 mapping ok ALSA device list: #0: tbd (WM8731) TCP cubic registered NET: Registered protocol family 17 NET: Registered protocol family 15 Power Management for TI OMAP3. VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 1 drivers/rtc/hctosys.c: unable to open rtc device (rtc0) hub 2-0:1.0: state 7 ports 3 chg 0000 evt 0000 net eth0: SMSC911x/921x identified at 0xc88ae000, IRQ: 222 IP-Config: Complete: device=3Deth0, addr=3D192.168.2.168, mask=3D255.255.255.0, gw=3D19= 2.168.2.1, host=3Dtbd, domain=3D, nis-domain=3D(none), bootserver=3D192.168.2.10, rootserver=3D192.168.2.10, rootpath=3D Looking up port of RPC 100003/2 on 192.168.2.10 hub 1-0:1.0: hub_suspend usb usb1: bus auto-suspend hub 2-0:1.0: hub_suspend usb usb2: bus auto-suspend ehci-omap ehci-omap.0: suspend root hub Looking up port of RPC 100005/1 on 192.168.2.10 VFS: Mounted root (nfs filesystem) on device 0:12. =46reeing init memory: 164K usb usb2: uevent usb 2-0:1.0: uevent usb usb1: uevent usb 1-0:1.0: uevent usb usb1: uevent usb usb2: uevent usb usb2: uevent usb 2-0:1.0: uevent usb usb1: uevent usb 1-0:1.0: uevent --=20 Bill Gatliff bgat@billgatliff.com -- To unsubscribe from this list: send the line "unsubscribe linux-omap" i= n the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html