From: Armando VISCONTI <armando.visconti@st.com>
To: u-boot@lists.denx.de
Subject: [U-Boot] [PATCH v5 00/18] Network support for spear platforms and SPEAr1300
Date: Wed, 30 Jun 2010 15:35:45 +0200 [thread overview]
Message-ID: <4C2B4831.9070008@st.com> (raw)
In-Reply-To: <1277789026-6802-1-git-send-email-vipin.kumar@st.com>
Tom, Wolfgang,
THis time everything should be ok.
Thks for your attention,
Arm
Vipin KUMAR wrote:
> Dear Wolfgang, Tom,
>
> The following set of patches is the fifth iteration of patches for the following
> changes
> -> Network device driver for synopsys designware peripheral
> -> SPEAr1300 SoC support
> -> A few other misc changes and bugfixes
>
> These also include the feedbacks given by Tom and Ben
> These set of patches are rebased on e5ed138a23923ebe61843244748d98d3dbc04777
>
> Please include these changes in the mainline u-boot
>
> Regards
> Vipin
>
> Vipin KUMAR (18):
> change_bit routine defined
> SPEAr : SMI erase and write timeouts increased
> SPEAr : Placing ethaddr write and read within CONFIG_CMD_NET
> SPEAr : Reducing the max RAM size to 128MB
> SPEAr : Basic arch related support added for SPEAr SoCs
> SPEAr : Network driver support added
> SPEAr : Network support configured for spear SoCs
> SPEAr : macb driver support added for spear310 and spear320
> SPEAr : FSMC driver support added
> SPEAr : Configuring FSMC driver for NAND interface
> SPEAr : i2c driver moved completely into drivers/i2c
> SPEAr : smi driver moved completely into drivers/mtd
> SPEAr : USB Device Controller driver support added
> SPEAr : Supporting various configurations for spear3xx and spear6xx
> boards
> SPEAr : Basic spear1300 architecture support added
> SPEAr : spear1300 SoC support added
> SPEAr : Removing extraneous code
> SPEAr : USB device controller bugfixes
>
> MAINTAINERS | 1 +
> MAKEALL | 1 +
> Makefile | 28 +-
> arch/arm/cpu/arm926ejs/spear/Makefile | 3 +-
> arch/arm/cpu/arm926ejs/spear/cpu.c | 78 +++
> arch/arm/cpu/arm_cortexa8/spear13xx/Makefile | 52 ++
> arch/arm/cpu/arm_cortexa8/spear13xx/cache.S | 114 +++++
> arch/arm/cpu/arm_cortexa8/spear13xx/cpu.c | 96 ++++
> .../arm_cortexa8/spear13xx/reset.c} | 52 +--
> arch/arm/cpu/arm_cortexa8/spear13xx/timer.c | 138 +++++
> .../arm/include/asm/arch-spear/clk.h | 26 +-
> arch/arm/include/asm/arch-spear/hardware.h | 16 +-
> arch/arm/include/asm/arch-spear/spr_misc.h | 5 +
> .../arm/include/asm/arch-spear13xx/hardware.h | 33 +-
> arch/arm/include/asm/arch-spear13xx/spr_gpt.h | 85 ++++
> arch/arm/include/asm/arch-spear13xx/spr_misc.h | 317 ++++++++++++
> .../arm/include/asm/arch-spear13xx/sys_proto.h | 29 +-
> arch/arm/include/asm/bitops.h | 11 +-
> board/spear/common/Makefile | 10 +-
> board/spear/common/spr_misc.c | 32 +-
> board/spear/spear1300/Makefile | 51 ++
> board/spear/spear1300/config.mk | 28 +
> board/spear/spear1300/spear1300.c | 88 ++++
> .../spear/spear1300/spr_lowlevel_init.S | 35 +-
> board/spear/spear300/config.mk | 11 -
> board/spear/spear300/spear300.c | 18 +-
> board/spear/spear310/config.mk | 11 -
> board/spear/spear310/spear310.c | 35 ++-
> board/spear/spear320/config.mk | 11 -
> board/spear/spear320/spear320.c | 23 +-
> board/spear/spear600/config.mk | 11 -
> board/spear/spear600/spear600.c | 18 +-
> doc/README.designware_eth | 25 +
> doc/README.spear | 46 ++-
> drivers/i2c/Makefile | 2 +-
> drivers/i2c/{spr_i2c.c => designware_i2c.c} | 4 +-
> .../spr_i2c.h => drivers/i2c/designware_i2c.h | 6 +-
> drivers/mtd/Makefile | 2 +-
> drivers/mtd/nand/Makefile | 2 +-
> drivers/mtd/nand/fsmc_nand.c | 366 ++++++++++++++
> drivers/mtd/nand/spr_nand.c | 124 -----
> drivers/mtd/{spr_smi.c => st_smi.c} | 59 ++-
> .../arch-spear/spr_smi.h => drivers/mtd/st_smi.h | 8 +-
> drivers/net/Makefile | 1 +
> drivers/net/designware.c | 531 ++++++++++++++++++++
> drivers/net/designware.h | 264 ++++++++++
> drivers/serial/usbtty.h | 4 +-
> drivers/usb/gadget/Makefile | 2 +-
> drivers/usb/gadget/{spr_udc.c => designware_udc.c} | 116 +++--
> include/configs/spear-common.h | 33 +-
> include/configs/spear13xx_evb.h | 202 ++++++++
> include/configs/{spear3xx.h => spear3xx_evb.h} | 30 ++
> include/configs/{spear6xx.h => spear6xx_evb.h} | 13 +
> include/linux/mtd/fsmc_nand.h | 104 ++++
> include/netdev.h | 1 +
> include/usb/{spr_udc.h => designware_udc.h} | 6 +-
> 56 files changed, 2997 insertions(+), 421 deletions(-)
> create mode 100644 arch/arm/cpu/arm926ejs/spear/cpu.c
> create mode 100644 arch/arm/cpu/arm_cortexa8/spear13xx/Makefile
> create mode 100644 arch/arm/cpu/arm_cortexa8/spear13xx/cache.S
> create mode 100644 arch/arm/cpu/arm_cortexa8/spear13xx/cpu.c
> rename arch/arm/{include/asm/arch-spear/spr_nand.h => cpu/arm_cortexa8/spear13xx/reset.c} (50%)
> mode change 100644 => 100755
> create mode 100644 arch/arm/cpu/arm_cortexa8/spear13xx/timer.c
> copy include/configs/spear6xx.h => arch/arm/include/asm/arch-spear/clk.h (64%)
> copy include/configs/spear6xx.h => arch/arm/include/asm/arch-spear13xx/hardware.h (58%)
> create mode 100644 arch/arm/include/asm/arch-spear13xx/spr_gpt.h
> create mode 100644 arch/arm/include/asm/arch-spear13xx/spr_misc.h
> copy include/configs/spear6xx.h => arch/arm/include/asm/arch-spear13xx/sys_proto.h (64%)
> create mode 100644 board/spear/spear1300/Makefile
> create mode 100644 board/spear/spear1300/config.mk
> create mode 100644 board/spear/spear1300/spear1300.c
> copy include/configs/spear6xx.h => board/spear/spear1300/spr_lowlevel_init.S (56%)
> create mode 100644 doc/README.designware_eth
> rename drivers/i2c/{spr_i2c.c => designware_i2c.c} (98%)
> rename arch/arm/include/asm/arch-spear/spr_i2c.h => drivers/i2c/designware_i2c.h (98%)
> create mode 100644 drivers/mtd/nand/fsmc_nand.c
> delete mode 100644 drivers/mtd/nand/spr_nand.c
> rename drivers/mtd/{spr_smi.c => st_smi.c} (94%)
> rename arch/arm/include/asm/arch-spear/spr_smi.h => drivers/mtd/st_smi.h (96%)
> create mode 100644 drivers/net/designware.c
> create mode 100644 drivers/net/designware.h
> rename drivers/usb/gadget/{spr_udc.c => designware_udc.c} (91%)
> create mode 100644 include/configs/spear13xx_evb.h
> rename include/configs/{spear3xx.h => spear3xx_evb.h} (85%)
> rename include/configs/{spear6xx.h => spear6xx_evb.h} (82%)
> create mode 100644 include/linux/mtd/fsmc_nand.h
> rename include/usb/{spr_udc.h => designware_udc.h} (98%)
>
>
>
prev parent reply other threads:[~2010-06-30 13:35 UTC|newest]
Thread overview: 23+ messages / expand[flat|nested] mbox.gz Atom feed top
2010-06-29 5:23 [U-Boot] [PATCH v5 00/18] Network support for spear platforms and SPEAr1300 Vipin KUMAR
2010-06-29 5:23 ` [U-Boot] [PATCH v5 01/18] change_bit routine defined Vipin KUMAR
2010-06-29 5:23 ` [U-Boot] [PATCH v5 02/18] SPEAr : SMI erase and write timeouts increased Vipin KUMAR
2010-06-29 5:23 ` [U-Boot] [PATCH v5 03/18] SPEAr : Placing ethaddr write and read within CONFIG_CMD_NET Vipin KUMAR
2010-06-29 5:23 ` [U-Boot] [PATCH v5 04/18] SPEAr : Reducing the max RAM size to 128MB Vipin KUMAR
2010-06-29 5:23 ` [U-Boot] [PATCH v5 05/18] SPEAr : Basic arch related support added for SPEAr SoCs Vipin KUMAR
2010-06-29 5:23 ` [U-Boot] [PATCH v5 06/18] SPEAr : Network driver support added Vipin KUMAR
2010-06-29 5:23 ` [U-Boot] [PATCH v5 07/18] SPEAr : Network support configured for spear SoCs Vipin KUMAR
2010-06-29 5:23 ` [U-Boot] [PATCH v5 08/18] SPEAr : macb driver support added for spear310 and spear320 Vipin KUMAR
2010-06-29 5:23 ` [U-Boot] [PATCH v5 09/18] SPEAr : FSMC driver support added Vipin KUMAR
2010-06-29 5:23 ` [U-Boot] [PATCH v5 10/18] SPEAr : Configuring FSMC driver for NAND interface Vipin KUMAR
2010-06-29 5:23 ` [U-Boot] [PATCH v5 11/18] SPEAr : i2c driver moved completely into drivers/i2c Vipin KUMAR
2010-06-29 5:23 ` [U-Boot] [PATCH v5 12/18] SPEAr : smi driver moved completely into drivers/mtd Vipin KUMAR
2010-06-29 5:23 ` [U-Boot] [PATCH v5 13/18] SPEAr : USB Device Controller driver support added Vipin KUMAR
2010-06-29 5:23 ` [U-Boot] [PATCH v5 14/18] SPEAr : Supporting various configurations for spear3xx and spear6xx boards Vipin KUMAR
2010-06-29 5:23 ` [U-Boot] [PATCH v5 15/18] SPEAr : Basic spear1300 architecture support added Vipin KUMAR
2010-06-29 5:23 ` [U-Boot] [PATCH v5 16/18] SPEAr : spear1300 SoC " Vipin KUMAR
2010-06-29 5:23 ` [U-Boot] [PATCH v5 17/18] SPEAr : Removing extraneous code Vipin KUMAR
2010-06-29 5:23 ` [U-Boot] [PATCH v5 18/18] SPEAr : USB device controller bugfixes Vipin KUMAR
2010-06-29 18:36 ` [U-Boot] [PATCH v5 10/18] SPEAr : Configuring FSMC driver for NAND interface Scott Wood
2010-06-29 18:35 ` [U-Boot] [PATCH v5 09/18] SPEAr : FSMC driver support added Scott Wood
2010-07-12 7:07 ` [U-Boot] [PATCH v5 06/18] SPEAr : Network " Ben Warren
2010-06-30 13:35 ` Armando VISCONTI [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=4C2B4831.9070008@st.com \
--to=armando.visconti@st.com \
--cc=u-boot@lists.denx.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.