Re: [PATCH] mvsas: mvs_lu_reset iterates phy num times when releasing task

[Konstantinos Skarlatos <k.skarlatos@gmail.com>]

  On 8/9/2010 1:53 μμ, Konstantinos Skarlatos wrote:
>  On 4/9/2010 1:13 πμ, David Milburn wrote:
>> On Fri, Aug 06, 2010 at 08:21:16PM +0300, Konstantinos Skarlatos wrote:
>>> >    Hello,
>>> > >  Does this patch fix any of the mvs_abort_task:rc= 5 and the other
>>> >  problems that are being reported for this driver? for more info 
>>> please
>>> >  seehttp://marc.info/?l=linux-scsi&m=127583131805429&w=2
>>> > 
>> Hello,
>>
>> Can you see if this patch prevents the ata_qc_issue warning?
>>
>> Thanks,
>> David
>>
>>   drivers/scsi/libsas/sas_ata.c |    1 +
>>   1 files changed, 1 insertions(+), 0 deletions(-)
>>
>> diff --git a/drivers/scsi/libsas/sas_ata.c 
>> b/drivers/scsi/libsas/sas_ata.c
>> index 042153c..ddbade7 100644
>> --- a/drivers/scsi/libsas/sas_ata.c
>> +++ b/drivers/scsi/libsas/sas_ata.c
>> @@ -347,6 +347,7 @@ static int sas_ata_scr_read(struct ata_link 
>> *link, unsigned int sc_reg_in,
>>   static struct ata_port_operations sas_sata_ops = {
>>       .phy_reset        = sas_ata_phy_reset,
>>       .post_internal_cmd    = sas_ata_post_internal,
>> +    .qc_defer               = ata_std_qc_defer,
>>       .qc_prep        = ata_noop_qc_prep,
>>       .qc_issue        = sas_ata_qc_issue,
>>       .qc_fill_rtf        = sas_ata_qc_fill_rtf,
>
> Hello,
>
> I have been unable to patch my kernel, I am a noob at this and the 
> method i used a few months ago to apply Srinivas patches for mvsas 
> does not work now. I have asked for help from my distro (arch linux), 
> but if you have a quick and easy way for me to patch sas_ata.c and 
> reload the module without reboots or complete kernel recompilations I 
> would be grateful to hear it.
>
> Kind regards
Hi, I finally managed to compile libsas. Here is dmesg output when 
loading mvsas (BTW what do the messages about ata38.00 mean?). I will 
report back when I do more testing

mvsas 0000:05:00.0: mvsas: driver version 0.8.2
mvsas 0000:05:00.0: PCI INT A -> Link[APC3] -> GSI 18 (level, low) -> IRQ 18
mvsas 0000:05:00.0: setting latency timer to 64
mvsas 0000:05:00.0: mvsas: PCI-E x4, Bandwidth Usage: 2.5 Gbps
scsi13 : mvsas
drivers/scsi/mvsas/mv_sas.c 1260:set wide port phy map 1
drivers/scsi/mvsas/mv_sas.c 1260:set wide port phy map 3
drivers/scsi/mvsas/mv_sas.c 1260:set wide port phy map 7
drivers/scsi/mvsas/mv_sas.c 1260:set wide port phy map f
ata38.00: ATA-8: ST31500541AS, CC34, max UDMA/133
ata38.00: 2930277168 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata38.00: qc timeout (cmd 0xec)
ata38.00: failed to IDENTIFY (I/O error, err_mask=0x4)
ata38.00: revalidation failed (errno=-5)
drivers/scsi/mvsas/mv_sas.c 1586:mvs_I_T_nexus_reset for device[1]:rc= 0
ata38.00: failed to IDENTIFY (I/O error, err_mask=0x100)
ata38: limiting SATA link speed to 1.5 Gbps
ata38.00: limiting speed to UDMA/133:PIO3
drivers/scsi/mvsas/mv_sas.c 1586:mvs_I_T_nexus_reset for device[1]:rc= 0
ata38.00: ATA-8: ST31500541AS, CC34, max UDMA/133
ata38.00: 2930277168 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata38.00: configured for UDMA/133
scsi 13:0:0:0: Direct-Access     ATA      ST31500541AS     CC34 PQ: 0 
ANSI: 5
sd 13:0:0:0: Attached scsi generic sg1 type 0
sd 13:0:0:0: [sdb] 2930277168 512-byte logical blocks: (1.50 TB/1.36 TiB)
sd 13:0:0:0: [sdb] Write Protect is off
sd 13:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 13:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't 
support DPO or FUA
  sdb:
ata39.00: ATA-8: ST31500541AS, CC32, max UDMA/133
ata39.00: 2930277168 sectors, multi 0: LBA48 NCQ (depth 31/32)
  sdb1
sd 13:0:0:0: [sdb] Attached SCSI disk
ata39.00: configured for UDMA/133
scsi 13:0:1:0: Direct-Access     ATA      ST31500541AS     CC32 PQ: 0 
ANSI: 5
sd 13:0:1:0: Attached scsi generic sg2 type 0
sd 13:0:1:0: [sdc] 2930277168 512-byte logical blocks: (1.50 TB/1.36 TiB)
sd 13:0:1:0: [sdc] Write Protect is off
sd 13:0:1:0: [sdc] Mode Sense: 00 3a 00 00
sd 13:0:1:0: [sdc] Write cache: enabled, read cache: enabled, doesn't 
support DPO or FUA
  sdc: sdc1
sd 13:0:1:0: [sdc] Attached SCSI disk
ata40.00: ATA-8: WDC WD15EADS-00S2B0, 01.00A01, max UDMA/133
ata40.00: 2930277168 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata40.00: configured for UDMA/133
scsi 13:0:2:0: Direct-Access     ATA      WDC WD15EADS-00S 01.0 PQ: 0 
ANSI: 5
sd 13:0:2:0: Attached scsi generic sg3 type 0
sd 13:0:2:0: [sdd] 2930277168 512-byte logical blocks: (1.50 TB/1.36 TiB)
sd 13:0:2:0: [sdd] Write Protect is off
sd 13:0:2:0: [sdd] Mode Sense: 00 3a 00 00
sd 13:0:2:0: [sdd] Write cache: enabled, read cache: enabled, doesn't 
support DPO or FUA
  sdd:
ata41.00: ATA-8: ST31500541AS, CC32, max UDMA/133
ata41.00: 2930277168 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata41.00: configured for UDMA/133
scsi 13:0:3:0: Direct-Access     ATA      ST31500541AS     CC32 PQ: 0 
ANSI: 5
sd 13:0:3:0: Attached scsi generic sg4 type 0
sd 13:0:3:0: [sde] 2930277168 512-byte logical blocks: (1.50 TB/1.36 TiB)
sd 13:0:3:0: [sde] Write Protect is off
sd 13:0:3:0: [sde] Mode Sense: 00 3a 00 00
sd 13:0:3:0: [sde] Write cache: enabled, read cache: enabled, doesn't 
support DPO or FUA
  sde: sde1
sd 13:0:3:0: [sde] Attached SCSI disk
ata42.00: ATA-8: ST31500541AS, CC34, max UDMA/133
ata42.00: 2930277168 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata42.00: configured for UDMA/133
scsi 13:0:4:0: Direct-Access     ATA      ST31500541AS     CC34 PQ: 0 
ANSI: 5
sd 13:0:4:0: [sdf] 2930277168 512-byte logical blocks: (1.50 TB/1.36 TiB)
sd 13:0:4:0: [sdf] Write Protect is off
sd 13:0:4:0: [sdf] Mode Sense: 00 3a 00 00
sd 13:0:4:0: [sdf] Write cache: enabled, read cache: enabled, doesn't 
support DPO or FUA
sd 13:0:4:0: Attached scsi generic sg5 type 0
  sdf:
ata43.00: ATA-8: ST31500541AS, CC34, max UDMA/133
ata43.00: 2930277168 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata43.00: configured for UDMA/133
scsi 13:0:5:0: Direct-Access     ATA      ST31500541AS     CC34 PQ: 0 
ANSI: 5
sd 13:0:5:0: Attached scsi generic sg6 type 0
sd 13:0:5:0: [sdg] 2930277168 512-byte logical blocks: (1.50 TB/1.36 TiB)
sd 13:0:5:0: [sdg] Write Protect is off
sd 13:0:5:0: [sdg] Mode Sense: 00 3a 00 00
sd 13:0:5:0: [sdg] Write cache: enabled, read cache: enabled, doesn't 
support DPO or FUA
  sdg:
ata44.00: ATA-8: ST31500541AS, CC32, max UDMA/133
ata44.00: 2930277168 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata44.00: configured for UDMA/133
scsi 13:0:6:0: Direct-Access     ATA      ST31500541AS     CC32 PQ: 0 
ANSI: 5
sd 13:0:6:0: Attached scsi generic sg7 type 0
sd 13:0:6:0: [sdh] 2930277168 512-byte logical blocks: (1.50 TB/1.36 TiB)
sd 13:0:6:0: [sdh] Write Protect is off
sd 13:0:6:0: [sdh] Mode Sense: 00 3a 00 00
sd 13:0:6:0: [sdh] Write cache: enabled, read cache: enabled, doesn't 
support DPO or FUA
  sdh: sdh1
sd 13:0:6:0: [sdh] Attached SCSI disk
ata45.00: ATA-8: ST31500541AS, CC34, max UDMA/133
ata45.00: 2930277168 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata45.00: configured for UDMA/133
scsi 13:0:7:0: Direct-Access     ATA      ST31500541AS     CC34 PQ: 0 
ANSI: 5
sd 13:0:7:0: Attached scsi generic sg8 type 0
sd 13:0:7:0: [sdi] 2930277168 512-byte logical blocks: (1.50 TB/1.36 TiB)
sd 13:0:7:0: [sdi] Write Protect is off
sd 13:0:7:0: [sdi] Mode Sense: 00 3a 00 00
sd 13:0:7:0: [sdi] Write cache: enabled, read cache: enabled, doesn't 
support DPO or FUA
  sdi:
ata46.00: ATA-8: ST31500541AS, CC32, max UDMA/133
ata46.00: 2930277168 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata46.00: configured for UDMA/133
scsi 13:0:8:0: Direct-Access     ATA      ST31500541AS     CC32 PQ: 0 
ANSI: 5
sd 13:0:8:0: Attached scsi generic sg9 type 0
sd 13:0:8:0: [sdj] 2930277168 512-byte logical blocks: (1.50 TB/1.36 TiB)
sd 13:0:8:0: [sdj] Write Protect is off
sd 13:0:8:0: [sdj] Mode Sense: 00 3a 00 00
sd 13:0:8:0: [sdj] Write cache: enabled, read cache: enabled, doesn't 
support DPO or FUA
  sdj: sdj1
sd 13:0:8:0: [sdj] Attached SCSI disk
ata47.00: qc timeout (cmd 0x27)
ata47.00: failed to read native max address (err_mask=0x4)
ata47.00: HPA support seems broken, skipping HPA handling
drivers/scsi/mvsas/mv_sas.c 1586:mvs_I_T_nexus_reset for device[a]:rc= 0
  sdi1
sd 13:0:7:0: [sdi] Attached SCSI disk
ata47.00: ATA-8: ST31500341AS, CC1H, max UDMA/133
ata47.00: 2930277168 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata47.00: configured for UDMA/133
scsi 13:0:9:0: Direct-Access     ATA      ST31500341AS     CC1H PQ: 0 
ANSI: 5
sd 13:0:9:0: Attached scsi generic sg10 type 0
sd 13:0:9:0: [sdk] 2930277168 512-byte logical blocks: (1.50 TB/1.36 TiB)
sd 13:0:9:0: [sdk] Write Protect is off
sd 13:0:9:0: [sdk] Mode Sense: 00 3a 00 00
sd 13:0:9:0: [sdk] Write cache: enabled, read cache: enabled, doesn't 
support DPO or FUA
  sdk: sdk1
sd 13:0:9:0: [sdk] Attached SCSI disk
  sdf1
sd 13:0:4:0: [sdf] Attached SCSI disk
  sdg1
sd 13:0:5:0: [sdg] Attached SCSI disk
  sdd1
sd 13:0:2:0: [sdd] Attached SCSI disk
ata48.00: qc timeout (cmd 0x27)
ata48.00: failed to read native max address (err_mask=0x4)
ata48.00: HPA support seems broken, skipping HPA handling
drivers/scsi/mvsas/mv_sas.c 1586:mvs_I_T_nexus_reset for device[b]:rc= 0
ata48.00: ATA-8: ST31500341AS, CC1H, max UDMA/133
ata48.00: 2930277168 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata48.00: configured for UDMA/133
scsi 13:0:10:0: Direct-Access     ATA      ST31500341AS     CC1H PQ: 0 
ANSI: 5
sd 13:0:10:0: Attached scsi generic sg11 type 0
sd 13:0:10:0: [sdl] 2930277168 512-byte logical blocks: (1.50 TB/1.36 TiB)
sd 13:0:10:0: [sdl] Write Protect is off
sd 13:0:10:0: [sdl] Mode Sense: 00 3a 00 00
sd 13:0:10:0: [sdl] Write cache: enabled, read cache: enabled, doesn't 
support DPO or FUA
  sdl:
ata49.00: ATA-8: ST31500541AS, CC32, max UDMA/133
ata49.00: 2930277168 sectors, multi 0: LBA48 NCQ (depth 31/32)
  sdl1
sd 13:0:10:0: [sdl] Attached SCSI disk
ata49.00: configured for UDMA/133
scsi 13:0:11:0: Direct-Access     ATA      ST31500541AS     CC32 PQ: 0 
ANSI: 5
sd 13:0:11:0: Attached scsi generic sg12 type 0
sd 13:0:11:0: [sdm] 2930277168 512-byte logical blocks: (1.50 TB/1.36 TiB)
sd 13:0:11:0: [sdm] Write Protect is off
sd 13:0:11:0: [sdm] Mode Sense: 00 3a 00 00
sd 13:0:11:0: [sdm] Write cache: enabled, read cache: enabled, doesn't 
support DPO or FUA
  sdm: sdm1
sd 13:0:11:0: [sdm] Attached SCSI disk
ata50.00: ATA-8: WDC WD15EADS-00P8B0, 01.00A01, max UDMA/133
ata50.00: 2930277168 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata50.00: configured for UDMA/133
scsi 13:0:12:0: Direct-Access     ATA      WDC WD15EADS-00P 01.0 PQ: 0 
ANSI: 5
sd 13:0:12:0: Attached scsi generic sg13 type 0
sd 13:0:12:0: [sdn] 2930277168 512-byte logical blocks: (1.50 TB/1.36 TiB)
sd 13:0:12:0: [sdn] Write Protect is off
sd 13:0:12:0: [sdn] Mode Sense: 00 3a 00 00
sd 13:0:12:0: [sdn] Write cache: enabled, read cache: enabled, doesn't 
support DPO or FUA
  sdn:
scsi 13:0:13:0: Enclosure         HP       HP SAS EXP Card  1.00 PQ: 0 
ANSI: 5
ses 13:0:13:0: Attached Enclosure device
ses 13:0:13:0: Attached scsi generic sg14 type 13
  sdn1
sd 13:0:12:0: [sdn] Attached SCSI disk

--
To unsubscribe from this list: send the line "unsubscribe linux-scsi" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html