From mboxrd@z Thu Jan 1 00:00:00 1970 From: =?ISO-8859-2?Q?Grzesiek_S=F3jka?= Subject: Re: GeForce FX5200 dual DVI & Samsung 204b Date: Fri, 01 Oct 2010 12:22:05 +0200 Message-ID: <4CA5B64D.8000608@pfu.pl> References: <4C9E0167.8000507@pfu.pl> <20100928004117.0a0ae0ca@daedalus.pq.iki.fi> <4CA1C6C0.1000709@pfu.pl> <20100928170227.00665f76@daedalus.pq.iki.fi> <4CA21515.4030903@pfu.pl> <20100929193136.644e0d68@daedalus.pq.iki.fi> <878w2jike0.fsf@riseup.net> <4CA4A934.4080109@pfu.pl> <87zkuzgqsv.fsf@riseup.net> <4CA4D199.8010403@pfu.pl> <87pqvuhksw.fsf@riseup.net> Mime-Version: 1.0 Content-Type: text/plain; charset="iso-8859-2"; Format="flowed" Content-Transfer-Encoding: quoted-printable Return-path: In-Reply-To: <87pqvuhksw.fsf-sGOZH3hwPm2sTnJN9+BGXg@public.gmane.org> List-Unsubscribe: , List-Archive: List-Post: List-Help: List-Subscribe: , Sender: nouveau-bounces+gcfxn-nouveau=m.gmane.org-PD4FTy7X32lNgt0PjOBp9y5qC8QIuHrW@public.gmane.org Errors-To: nouveau-bounces+gcfxn-nouveau=m.gmane.org-PD4FTy7X32lNgt0PjOBp9y5qC8QIuHrW@public.gmane.org To: Francisco Jerez Cc: nouveau-PD4FTy7X32lNgt0PjOBp9y5qC8QIuHrW@public.gmane.org List-Id: nouveau.vger.kernel.org On 10/01/10 01:29, Francisco Jerez wrote: > Grzesiek S=F3jka writes: > >> On 09/30/10 18:05, Francisco Jerez wrote: >>> Does the following command help? >>> $ xrandr --output DVI-I-2 --set "scaling mode" "None" >> Yes! Now I have: >> xrandr --output DVI-I-1 --set "scaling mode" "None" >> xrandr --output DVI-I-2 --set "scaling mode" "None" >> in xinitrc. Both displays work fine when Xserver is running. But after I >> go back to the console the display #1 switches off and #2 starts to >> blink again. Is it possible to fix the console?? >> > Do you need to tell the binary driver to do anything special to get it > working on those monitors? (e.g. manually specified timings or EDID) No, binary driver works fine without any extra settings. The version I = used was 173.14.22. With nouveau drivers I'm forced to use the following Modeline "1600x1200_def" 144 1600 1628 1788 1920 1200 1201 1204 1250 Without it the displays (both) are blinking. Remember that binary nvidia = claims that the MaxPixClk is 135MHz and nouveau says that it is 175MHz. = According to the spec it should be 162MHz. I'm not sure but I think that = this high rate works only with D-SUB. Actually I have 3 monitors and the = third one is connected with the ancient Matrox Millennium II card using = the D-SUB cable and it uses the modeline with the 162MHz PixClk. PS. By the way - I was force to install Win7 and it works with my LCD = without any drivers installed.