From: thomas schorpp <thomas.schorpp@googlemail.com>
To: linux-media@vger.kernel.org
Subject: Re: dvb-c: TT C-1501: tda827x.c: Cannot hold lock at 746 MHz
Date: Sat, 02 Oct 2010 17:19:28 +0200 [thread overview]
Message-ID: <4CA74D80.7000707@gmail.com> (raw)
In-Reply-To: <4CA74509.6000404@gmail.com>
Am 02.10.2010 16:43, schrieb thomas schorpp:
> Hello,
>
> Klaas patch is not complete:
> http://article.gmane.org/gmane.linux.drivers.dvb/47571
>
> I found a hole at 746MHz with 2.6.34.0 kernel and DE provider kabelbw.de,
> Picture fragments and audio bursts only:
>
> Oct 2 15:53:03 tom1 vdr: [16380] receiver on device 1 thread ended (pid=16268, tid=16380)
> Oct 2 15:53:03 tom1 kernel: tda827x: tda827xa_set_params:
> Oct 2 15:53:03 tom1 kernel: tda827x: tda827xa_set_params select tda827xa_dvbc
> Oct 2 15:53:03 tom1 kernel: tda827x: tda8275a AGC2 gain is: 4
> Oct 2 15:53:04 tom1 vdr: [16462] setting audio track to 1 (0)
> Oct 2 15:53:04 tom1 kernel: tda827x: tda827xa_set_params:
> Oct 2 15:53:04 tom1 kernel: tda827x: tda827xa_set_params select tda827xa_dvbc
> Oct 2 15:53:04 tom1 kernel: tda827x: tda8275a AGC2 gain is: 5
> Oct 2 15:53:04 tom1 vdr: [16279] frontend 0 lost lock on channel 496, tp 746
> Oct 2 15:53:04 tom1 vdr: [16279] frontend 0 regained lock on channel 496, tp 746
> Oct 2 15:53:05 tom1 kernel: tda827x: tda827xa_set_params:
> Oct 2 15:53:05 tom1 kernel: tda827x: tda827xa_set_params select tda827xa_dvbc
> Oct 2 15:53:05 tom1 kernel: tda827x: tda8275a AGC2 gain is: 4
> Oct 2 15:53:05 tom1 vdr: [16279] frontend 0 lost lock on channel 496, tp 746
> Oct 2 15:53:05 tom1 kernel: tda827x: tda827xa_set_params:
> Oct 2 15:53:05 tom1 kernel: tda827x: tda827xa_set_params select tda827xa_dvbc
> Oct 2 15:53:05 tom1 kernel: tda827x: tda8275a AGC2 gain is: 4
> Oct 2 15:53:05 tom1 kernel: tda827x: tda827xa_set_params:
> Oct 2 15:53:05 tom1 kernel: tda827x: tda827xa_set_params select tda827xa_dvbc
> Oct 2 15:53:05 tom1 kernel: tda827x: tda8275a AGC2 gain is: 5
> Oct 2 15:53:06 tom1 vdr: [16279] frontend 0 regained lock on channel 496, tp 746
> Oct 2 15:53:06 tom1 kernel: tda827x: tda827xa_set_params:
> Oct 2 15:53:06 tom1 kernel: tda827x: tda827xa_set_params select tda827xa_dvbc
> Oct 2 15:53:06 tom1 kernel: tda827x: tda8275a AGC2 gain is: 5
> Oct 2 15:53:06 tom1 kernel: tda827x: tda827xa_set_params:
> Oct 2 15:53:06 tom1 kernel: tda827x: tda827xa_set_params select tda827xa_dvbc
> Oct 2 15:53:06 tom1 kernel: tda827x: tda8275a AGC2 gain is: 5
> Oct 2 15:53:06 tom1 kernel: tda827x: tda827xa_set_params:
> Oct 2 15:53:06 tom1 kernel: tda827x: tda827xa_set_params select tda827xa_dvbc
> Oct 2 15:53:06 tom1 kernel: tda827x: tda8275a AGC2 gain is: 4
> Oct 2 15:53:06 tom1 vdr: [16268] switching to channel 494
>
> cycle: 78 d_time: 0.004 s Sig: 51657 SNR: 43690 BER: 1728 UBLK: 55 Stat: 0x00 []
> cycle: 79 d_time: 0.004 s Sig: 52428 SNR: 60395 BER: 1728 UBLK: 57 Stat: 0x03 [SIG CARR ]
> cycle: 80 d_time: 0.004 s Sig: 50886 SNR: 46517 BER: 1728 UBLK: 95 Stat: 0x00 []
> cycle: 81 d_time: 0.007 s Sig: 52428 SNR: 44461 BER: 1728 UBLK: 54 Stat: 0x03 [SIG CARR ]
> cycle: 82 d_time: 0.003 s Sig: 51657 SNR: 61423 BER: 1728 UBLK: 5 Stat: 0x1f [SIG CARR VIT SYNC LOCK ]
> cycle: 83 d_time: 0.237 s Sig: 40092 SNR: 47288 BER: 1048575 UBLK: 66 Stat: 0x00 []
> cycle: 84 d_time: 0.005 s Sig: 56283 SNR: 45232 BER: 1728 UBLK: 113 Stat: 0x00 []
> cycle: 85 d_time: 0.006 s Sig: 53199 SNR: 46774 BER: 1728 UBLK: 136 Stat: 0x00 []
> cycle: 86 d_time: 0.008 s Sig: 50115 SNR: 44975 BER: 1728 UBLK: 55 Stat: 0x00 []
> cycle: 87 d_time: 0.004 s Sig: 53199 SNR: 53970 BER: 1728 UBLK: 287 Stat: 0x1f [SIG CARR VIT SYNC LOCK ]
> cycle: 88 d_time: 0.020 s Sig: 50886 SNR: 61166 BER: 1728 UBLK: 62 Stat: 0x03 [SIG CARR ]
>
> Current parameters:
> Frequency: 746000.000 kHz
> Inversion: ON
> Symbol rate: 6.900000 MSym/s
> FEC: none
> Modulation: QAM 64
>
> Card is just bought newly:
>
> 00:06.0 0480: 1131:7146 (rev 01)
> Subsystem: 13c2:101a
> Flags: bus master, medium devsel, latency 32, IRQ 17
> Memory at fbeffc00 (32-bit, non-prefetchable) [size=512]
> Kernel driver in use: budget_ci dvb
>
> Other (tested favourite) channels are tuned in fine.
>
> No network problems for this transponder reported in cable provider's support forums.
>
> Anyone got the chips datasheet or a hint what to tweak in the tda827xa_dvbc[] for this frequency?
>
> { .lomax = 802000000, .svco = 2, .spd = 0, .scr = 2, .sbs = 4, .gc3 = 1}, ?
>
> thx,
> Y
> tom
>
>
>
Hm, this gets complicated, tuning is fine at 722+754MHz but not on 746MHz,
this is within the same control segment
{ .lomax = 720000000, .svco = 2, .spd = 0, .scr = 1, .sbs = 4, .gc3 = 1},
{ .lomax = 802000000, .svco = 2, .spd = 0, .scr = 2, .sbs = 4, .gc3 = 1},
next prev parent reply other threads:[~2010-10-02 15:19 UTC|newest]
Thread overview: 3+ messages / expand[flat|nested] mbox.gz Atom feed top
2010-10-02 14:43 dvb-c: TT C-1501: tda827x.c: Cannot hold lock at 746 MHz thomas schorpp
2010-10-02 15:19 ` thomas schorpp [this message]
2010-10-02 16:54 ` thomas schorpp
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=4CA74D80.7000707@gmail.com \
--to=thomas.schorpp@googlemail.com \
--cc=linux-media@vger.kernel.org \
--cc=thomas.schorpp@gmail.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.