From: Antti Palosaari <crope@iki.fi>
To: Paul Gover <pmw.gover@yahoo.co.uk>
Cc: linux-media@vger.kernel.org
Subject: Re: [linux-dvb] [bug] AF9015 message "WARNING: >>> tuning failed!!!"
Date: Wed, 06 Oct 2010 22:41:39 +0300 [thread overview]
Message-ID: <4CACD0F3.6030203@iki.fi> (raw)
In-Reply-To: <201010061456.19573.pmw.gover@yahoo.co.uk>
It is QT1010 tuner driver issue. None is working for that currently or
in near future. Feel free to fix :]
Antti
On 10/06/2010 04:56 PM, Paul Gover wrote:
> I've a cheap USB DVB key that won't work with Kaffeine.
> It identifies itself as KWorld USB DVB-T TV Stick II (VS-DVB-T 395U).
> It shows up on Kaffeine's "Configure Television" dialog,
> but scanning for channels finds nothing,
> and tuning using an old channel list gives "Sorry - no available device found"
>
> I had Kaffeine working OK with a different USB TV key.
>
> dvbscan produces "WARNING:>>> tuning failed!!!" messages.
>
> The key works on XP using KWorld's HyperMedia Center.
> Rebooting from there to Linux with warm USB key shows it contains 4.95.0
> firmware.
> At one point, such a warm reboot enabled Kaffeine to show TV.
> That was with one of the early KDE4 Kaffeine candidates,
> and an older linux kernel (sorry, I forget which).
>
> Now using kernel modules in Linux version 2.6.34-gentoo-r6.
> Kaffeine 1.0, KDE 4.4.5. linuxtv-dvb-apps 1.1.1.20080317
> on an ASUS EeePC 1000HE (Intel Atom processor).
>
> Diagnostic stuff
>
> lsusb -v :
>
> Bus 001 Device 023: ID 1b80:e396 Afatech
> Device Descriptor:
> bLength 18
> bDescriptorType 1
> bcdUSB 2.00
> bDeviceClass 0 (Defined at Interface level)
> bDeviceSubClass 0
> bDeviceProtocol 0
> bMaxPacketSize0 64
> idVendor 0x1b80 Afatech
> idProduct 0xe396
> bcdDevice 2.00
> iManufacturer 1 Afatech
> iProduct 2 DVB-T 2
> iSerial 0
> bNumConfigurations 1
> Configuration Descriptor:
> bLength 9
> bDescriptorType 2
> wTotalLength 46
> bNumInterfaces 1
> bConfigurationValue 1
> iConfiguration 0
> bmAttributes 0x80
> (Bus Powered)
> MaxPower 500mA
> Interface Descriptor:
> bLength 9
> bDescriptorType 4
> bInterfaceNumber 0
> bAlternateSetting 0
> bNumEndpoints 4
> bInterfaceClass 255 Vendor Specific Class
> bInterfaceSubClass 0
> bInterfaceProtocol 0
> iInterface 0
> Endpoint Descriptor:
> bLength 7
> bDescriptorType 5
> bEndpointAddress 0x81 EP 1 IN
> bmAttributes 2
> Transfer Type Bulk
> Synch Type None
> Usage Type Data
> wMaxPacketSize 0x0200 1x 512 bytes
> bInterval 0
> Endpoint Descriptor:
> bLength 7
> bDescriptorType 5
> bEndpointAddress 0x02 EP 2 OUT
> bmAttributes 2
> Transfer Type Bulk
> Synch Type None
> Usage Type Data
> wMaxPacketSize 0x0200 1x 512 bytes
> bInterval 0
> Endpoint Descriptor:
> bLength 7
> bDescriptorType 5
> bEndpointAddress 0x84 EP 4 IN
> bmAttributes 2
> Transfer Type Bulk
> Synch Type None
> Usage Type Data
> wMaxPacketSize 0x0200 1x 512 bytes
> bInterval 0
> Endpoint Descriptor:
> bLength 7
> bDescriptorType 5
> bEndpointAddress 0x85 EP 5 IN
> bmAttributes 2
> Transfer Type Bulk
> Synch Type None
> Usage Type Data
> wMaxPacketSize 0x0200 1x 512 bytes
> bInterval 0
> Device Qualifier (for other device speed):
> bLength 10
> bDescriptorType 6
> bcdUSB 2.00
> bDeviceClass 0 (Defined at Interface level)
> bDeviceSubClass 0
> bDeviceProtocol 0
> bMaxPacketSize0 64
> bNumConfigurations 1
> Device Status: 0x0000
> (Bus Powered)
>
> lsmod :
>
> Module Size Used by
> ppp_deflate 3156 0
> zlib_deflate 17980 1 ppp_deflate
> zlib_inflate 14197 1 ppp_deflate
> bsd_comp 4568 0
> ppp_async 6283 1
> crc_ccitt 1023 1 ppp_async
> ppp_generic 14958 7 ppp_deflate,bsd_comp,ppp_async
> slhc 4431 1 ppp_generic
> sr_mod 10825 0
> cdrom 29800 1 sr_mod
> option 18224 1
> usbserial 24352 4 option
> snd_seq_oss 23625 0
> snd_seq_midi_event 4280 1 snd_seq_oss
> snd_seq 39723 4 snd_seq_oss,snd_seq_midi_event
> snd_seq_device 4109 2 snd_seq_oss,snd_seq
> snd_pcm_oss 30331 0
> snd_mixer_oss 12481 1 snd_pcm_oss
> snd_hda_codec_realtek 187652 1
> qt1010 4461 1
> snd_hda_intel 16732 2
> af9013 17817 1
> snd_hda_codec 42659 2 snd_hda_codec_realtek,snd_hda_intel
> snd_pcm 50564 3 snd_pcm_oss,snd_hda_intel,snd_hda_codec
> dvb_usb_af9015 24963 0
> snd_timer 14785 2 snd_seq,snd_pcm
> snd 39369 14
> snd_seq_oss,snd_seq,snd_seq_device,snd_pcm_oss,snd_mixer_oss,snd_hda_codec_realtek,snd_hda_intel,snd_hda_codec,snd_pcm,snd_timer
> dvb_usb 15353 1 dvb_usb_af9015
> dvb_core 72670 1 dvb_usb
> snd_page_alloc 5445 2 snd_hda_intel,snd_pcm
>
> Syslog when connecting cold device (debug level 3) :
>
> usb 1-3: new high speed USB device using ehci_hcd and address 22
> af9015_usb_probe: interface:0
> af9015_eeprom_hash: eeprom sum=37ec4ddf
> af9015_read_config: IR mode:4
> af9015_read_config: TS mode:0
> af9015_read_config: [0] xtal:2 set adc_clock:28000
> af9015_read_config: [0] IF1:36125
> af9015_read_config: [0] MT2060 IF1:5888
> af9015_read_config: [0] tuner id:134
> af9015_identify_state: reply:01
> af9015_download_firmware:
> dvb-usb: found a 'KWorld USB DVB-T TV Stick II (VS-DVB-T 395U)' in cold state,
> will try to load a firmware
> usb 1-3: firmware: requesting dvb-usb-af9015.fw
> dvb-usb: downloading firmware from file 'dvb-usb-af9015.fw'
> dvb-usb: found a 'KWorld USB DVB-T TV Stick II (VS-DVB-T 395U)' in warm state.
> dvb-usb: will pass the complete MPEG2 transport stream to the software
> demuxer.
> DVB: registering new adapter (KWorld USB DVB-T TV Stick II (VS-DVB-T 395U))
> af9013: firmware version:4.95.0
> af9015_af9013_frontend_attach: init I2C
> af9015_i2c_init:
> Quantek QT1010 successfully identified.
> input: IR-receiver inside an USB DVB receiver as
> /devices/pci0000:00/0000:00:1d.7/usb1/1-3/input/input12
> dvb-usb: schedule remote query interval to 150 msecs.
> dvb-usb: KWorld USB DVB-T TV Stick II (VS-DVB-T 395U) successfully initialized
> and connected.
> DVB: registering adapter 0 frontend 0 (Afatech AF9013 DVB-T)...
> af9015_tuner_attach:
> af9015_init:
> af9015_init_endpoint: USB speed:3
> af9015_download_ir_table:
>
> and on disconnection:
>
> usb 1-3: USB disconnect, address 22
> dvb-usb: KWorld USB DVB-T TV Stick II (VS-DVB-T 395U) successfully
> deinitialized and disconnected.
> af9015_usb_device_exit:
> af9015_i2c_exit:
> input device has been disconnected
>
> ls -l /dev/dvb/adapter0/ :
>
> total 0
> crw-rw---- 1 root video 212, 4 Oct 6 12:43 demux0
> crw-rw---- 1 root video 212, 5 Oct 6 12:43 dvr0
> crw-rw---- 1 root video 212, 3 Oct 6 12:43 frontend0
> crw-rw---- 1 root video 212, 7 Oct 6 12:43 net0
>
> dvbscan -uvvt1 /usr/share/dvb/dvb-t/uk-Rowridge :
>
> scanning /usr/share/dvb/dvb-t/uk-Rowridge
> using '/dev/dvb/adapter0/frontend0' and '/dev/dvb/adapter0/demux0'
> initial transponder 489833000 0 3 9 1 0 0 0
> initial transponder 530000000 0 2 9 3 0 0 0
> initial transponder 545833000 0 2 9 3 0 0 0
> initial transponder 562167000 0 3 9 1 0 0 0
> initial transponder 513833000 0 3 9 1 0 0 0
> initial transponder 570167000 0 3 9 1 0 0 0
>>>> tune to:
> 489833000:INVERSION_AUTO:BANDWIDTH_8_MHZ:FEC_3_4:FEC_AUTO:QAM_16:TRANSMISSION_MODE_2K:GUARD_INTERVAL_1_32:HIERARCHY_NONE
>>>> tuning status == 0x03
>>>> tuning status == 0x03
>>>> tuning status == 0x03
>>>> tuning status == 0x03
>>>> tuning status == 0x03
>>>> tuning status == 0x03
>>>> tuning status == 0x03
>>>> tuning status == 0x03
>>>> tuning status == 0x03
>>>> tuning status == 0x03
> WARNING:>>> tuning failed!!!
>>>> tune to:
> 489833000:INVERSION_AUTO:BANDWIDTH_8_MHZ:FEC_3_4:FEC_AUTO:QAM_16:TRANSMISSION_MODE_2K:GUARD_INTERVAL_1_32:HIERARCHY_NONE
> (tuning failed)
>>>> tuning status == 0x03
>>>> tuning status == 0x03
>>>> tuning status == 0x03
>>>> tuning status == 0x03
>>>> tuning status == 0x03
>>>> tuning status == 0x03
>>>> tuning status == 0x03
>>>> tuning status == 0x03
>>>> tuning status == 0x03
>>>> tuning status == 0x03
> WARNING:>>> tuning failed!!!
>
> ... repeated for each frequency
>
> ERROR: initial tuning failed
> dumping lists (0 services)
> Done.
>
> Thanks for any help.
> --
> To unsubscribe from this list: send the line "unsubscribe linux-media" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
--
http://palosaari.fi/
next prev parent reply other threads:[~2010-10-06 19:41 UTC|newest]
Thread overview: 4+ messages / expand[flat|nested] mbox.gz Atom feed top
2010-10-06 13:56 [linux-dvb] [bug] AF9015 message "WARNING: >>> tuning failed!!!" Paul Gover
2010-10-06 19:41 ` Antti Palosaari [this message]
2010-10-06 20:36 ` dave cunningham
2010-10-06 21:29 ` Antti Palosaari
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=4CACD0F3.6030203@iki.fi \
--to=crope@iki.fi \
--cc=linux-media@vger.kernel.org \
--cc=pmw.gover@yahoo.co.uk \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.