Re: Re: system freeze when processor.ko is loaded during boot

[Martin Wilck <mwilck@arcor.de>]

[-- Attachment #1: Type: text/plain, Size: 2386 bytes --]

Hello Yunhong,

thanks for your reply, I am sorry it took me so long to respond.

> Martin, did you try latest origin/xen/stable-2.6.32.x branch to see if anything different? 

I ran 2.6.32.25 from Jeremy's branch, no change - system still freezes
if processor.ko is loaded at boot time.

xen-unstable changeset:   22417:c0c1f5f0745e
xen/stable-2.6.32.x commit: 481bd8e6b8dafed2ea445e8cde2abbbb95b49ec1

There was a bug in .32 branch on processor before, which should have
been fixed. And can you share the boot log and the feature supported in
this platform?

dmesg.txt (from non-xen kernel) is attached.

$ cat /proc/cpuinfo
processor       : 0
vendor_id       : GenuineIntel
cpu family      : 6
model           : 13
model name      : Intel(R) Pentium(R) M processor 2.13GHz
stepping        : 8
cpu MHz         : 800.000
cache size      : 2048 KB
fdiv_bug        : no
hlt_bug         : no
f00f_bug        : no
coma_bug        : no
fpu             : yes
fpu_exception   : yes
cpuid level     : 2
wp              : yes
flags           : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge
mca cmov clflush dts acpi mmx fxsr sse sse2 ss tm pbe up bts est tm2
bogomips        : 1596.16
clflush size    : 64
cache_alignment : 64
address sizes   : 32 bits physical, 32 bits virtual
power management:

$ cat /proc/acpi/processor/CPU0/power
active state:            C0
max_cstate:              C8
maximum allowed latency: 2000000000 usec
states:
    C1:                  type[C1] promotion[--] demotion[--]
latency[001] usage[00001533] duration[00000000000000000000]
    C2:                  type[C2] promotion[--] demotion[--]
latency[001] usage[00294108] duration[00000000004868085138]
    C3:                  type[C3] promotion[--] demotion[--]
latency[085] usage[00470473] duration[00000000008899295934]

$ cat /proc/acpi/processor/CPU0/info
processor id:            0
acpi id:                 0
bus mastering control:   yes
power management:        yes
throttling control:      yes
limit interface:         yes

> And I remember report about Xen freeze on some platform with HPET broadcast enabled http://lists.xensource.com/archives/html/xen-users/2010-09/msg00370.html , but not sure if it's the same issue with you (I checked that issue when it was reported and made no progress).
I played around with the hpet_broadcast xen paramter, but it didn't have
an effect.


Regards
Martin

[-- Attachment #2: dmesg.txt --]
[-- Type: text/plain, Size: 63313 bytes --]

[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Linux version 2.6.34-12-default (geeko@buildhost) (gcc version 4.5.0 20100604 [gcc-4_5-branch revision 160292] (SUSE Linux) ) #1 SMP 2010-06-29 02:39:08 +0200
[    0.000000] BIOS-provided physical RAM map:
[    0.000000]  BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
[    0.000000]  BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
[    0.000000]  BIOS-e820: 00000000000d0000 - 00000000000d4000 (reserved)
[    0.000000]  BIOS-e820: 00000000000dc000 - 0000000000100000 (reserved)
[    0.000000]  BIOS-e820: 0000000000100000 - 000000007fea0000 (usable)
[    0.000000]  BIOS-e820: 000000007fea0000 - 000000007feb1000 (ACPI data)
[    0.000000]  BIOS-e820: 000000007feb1000 - 000000007ff00000 (ACPI NVS)
[    0.000000]  BIOS-e820: 000000007ff00000 - 0000000080000000 (reserved)
[    0.000000]  BIOS-e820: 00000000e0000000 - 00000000f0006000 (reserved)
[    0.000000]  BIOS-e820: 00000000f0008000 - 00000000f000c000 (reserved)
[    0.000000]  BIOS-e820: 00000000fed00000 - 00000000fed00400 (reserved)
[    0.000000]  BIOS-e820: 00000000fed20000 - 00000000fed90000 (reserved)
[    0.000000]  BIOS-e820: 00000000ff000000 - 0000000100000000 (reserved)
[    0.000000] Notice: NX (Execute Disable) protection missing in CPU or disabled in BIOS!
[    0.000000] DMI present.
[    0.000000] Phoenix BIOS detected: BIOS may corrupt low RAM, working around it.
[    0.000000] e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
[    0.000000] e820 update range: 0000000000000000 - 0000000000001000 (usable) ==> (reserved)
[    0.000000] e820 remove range: 00000000000a0000 - 0000000000100000 (usable)
[    0.000000] last_pfn = 0x7fea0 max_arch_pfn = 0x100000
[    0.000000] MTRR default type: uncachable
[    0.000000] MTRR fixed ranges enabled:
[    0.000000]   00000-9FFFF write-back
[    0.000000]   A0000-BFFFF uncachable
[    0.000000]   C0000-CFFFF write-protect
[    0.000000]   D0000-E3FFF uncachable
[    0.000000]   E4000-FFFFF write-protect
[    0.000000] MTRR variable ranges enabled:
[    0.000000]   0 base 000000000 mask F80000000 write-back
[    0.000000]   1 base 07FF00000 mask FFFF00000 uncachable
[    0.000000]   2 disabled
[    0.000000]   3 disabled
[    0.000000]   4 disabled
[    0.000000]   5 disabled
[    0.000000]   6 disabled
[    0.000000]   7 disabled
[    0.000000] PAT not supported by CPU.
[    0.000000] Scanning 0 areas for low memory corruption
[    0.000000] modified physical RAM map:
[    0.000000]  modified: 0000000000000000 - 0000000000010000 (reserved)
[    0.000000]  modified: 0000000000010000 - 000000000009f800 (usable)
[    0.000000]  modified: 000000000009f800 - 00000000000a0000 (reserved)
[    0.000000]  modified: 00000000000d0000 - 00000000000d4000 (reserved)
[    0.000000]  modified: 00000000000dc000 - 0000000000100000 (reserved)
[    0.000000]  modified: 0000000000100000 - 000000007fea0000 (usable)
[    0.000000]  modified: 000000007fea0000 - 000000007feb1000 (ACPI data)
[    0.000000]  modified: 000000007feb1000 - 000000007ff00000 (ACPI NVS)
[    0.000000]  modified: 000000007ff00000 - 0000000080000000 (reserved)
[    0.000000]  modified: 00000000e0000000 - 00000000f0006000 (reserved)
[    0.000000]  modified: 00000000f0008000 - 00000000f000c000 (reserved)
[    0.000000]  modified: 00000000fed00000 - 00000000fed00400 (reserved)
[    0.000000]  modified: 00000000fed20000 - 00000000fed90000 (reserved)
[    0.000000]  modified: 00000000ff000000 - 0000000100000000 (reserved)
[    0.000000] initial memory mapped : 0 - 00c00000
[    0.000000] init_memory_mapping: 0000000000000000-00000000377fe000
[    0.000000]  0000000000 - 0000400000 page 4k
[    0.000000]  0000400000 - 0037400000 page 2M
[    0.000000]  0037400000 - 00377fe000 page 4k
[    0.000000] kernel direct mapping tables up to 377fe000 @ 15000-1a000
[    0.000000] RAMDISK: 37441000 - 37ff0000
[    0.000000] Allocated new RAMDISK: 009f6000 - 015a44c5
[    0.000000] Move RAMDISK from 0000000037441000 - 0000000037fef4c4 to 009f6000 - 015a44c4
[    0.000000] ACPI: RSDP 000f7730 00014 (v00 PTLTD )
[    0.000000] ACPI: RSDT 7fea9ede 0004C (v01 PTLTD  Ohlone00 06040000  LTP 00000000)
[    0.000000] ACPI: FACP 7feb0e96 00074 (v01 INTEL  ALVISO   06040000 LOHR 0000005F)
[    0.000000] ACPI: DSDT 7feab3b9 05ADD (v01 INTEL  ALVISO   06040000 INTL 20030224)
[    0.000000] ACPI: FACS 7feb1fc0 00040
[    0.000000] ACPI: APIC 7feb0f0a 0005A (v01 INTEL  ALVISO   06040000 LOHR 0000005F)
[    0.000000] ACPI: HPET 7feb0f64 00038 (v01 INTEL  ALVISO   06040000 LOHR 0000005F)
[    0.000000] ACPI: MCFG 7feb0f9c 0003C (v01 INTEL  ALVISO   06040000 LOHR 0000005F)
[    0.000000] ACPI: BOOT 7feb0fd8 00028 (v01 PTLTD  $SBFTBL$ 06040000  LTP 00000001)
[    0.000000] ACPI: SSDT 7feaad6a 0064F (v01 SataRe  SataPri 00001000 INTL 20030224)
[    0.000000] ACPI: SSDT 7feaa6d8 00692 (v01 SataRe  SataSec 00001000 INTL 20030224)
[    0.000000] ACPI: SSDT 7feaa1ad 0039F (v01  PmRef  Cpu0Ist 00003000 INTL 20030224)
[    0.000000] ACPI: SSDT 7fea9ff3 001BA (v01  PmRef  Cpu0Cst 00003001 INTL 20030224)
[    0.000000] ACPI: SSDT 7fea9f2a 000C9 (v01  PmRef    CpuPm 00003000 INTL 20030224)
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] 1158MB HIGHMEM available.
[    0.000000] 887MB LOWMEM available.
[    0.000000]   mapped low ram: 0 - 377fe000
[    0.000000]   low ram: 0 - 377fe000
[    0.000000] Zone PFN ranges:
[    0.000000]   DMA      0x00000010 -> 0x00001000
[    0.000000]   Normal   0x00001000 -> 0x000377fe
[    0.000000]   HighMem  0x000377fe -> 0x0007fea0
[    0.000000] Movable zone start PFN for each node
[    0.000000] early_node_map[2] active PFN ranges
[    0.000000]     0: 0x00000010 -> 0x0000009f
[    0.000000]     0: 0x00000100 -> 0x0007fea0
[    0.000000] On node 0 totalpages: 523823
[    0.000000] free_area_init_node: node 0, pgdat c0882580, node_mem_map c15a6200
[    0.000000]   DMA zone: 32 pages used for memmap
[    0.000000]   DMA zone: 0 pages reserved
[    0.000000]   DMA zone: 3951 pages, LIFO batch:0
[    0.000000]   Normal zone: 1744 pages used for memmap
[    0.000000]   Normal zone: 221486 pages, LIFO batch:31
[    0.000000]   HighMem zone: 2318 pages used for memmap
[    0.000000]   HighMem zone: 294292 pages, LIFO batch:31
[    0.000000] Using APIC driver default
[    0.000000] ACPI: PM-Timer IO Port: 0x1008
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[    0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
[    0.000000] IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[    0.000000] ACPI: IRQ0 used by override.
[    0.000000] ACPI: IRQ2 used by override.
[    0.000000] ACPI: IRQ9 used by override.
[    0.000000] Using ACPI (MADT) for SMP configuration information
[    0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
[    0.000000] SMP: Allowing 1 CPUs, 0 hotplug CPUs
[    0.000000] nr_irqs_gsi: 24
[    0.000000] early_res array is doubled to 64 at [16000 - 167ff]
[    0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[    0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000d0000
[    0.000000] PM: Registered nosave memory: 00000000000d0000 - 00000000000d4000
[    0.000000] PM: Registered nosave memory: 00000000000d4000 - 00000000000dc000
[    0.000000] PM: Registered nosave memory: 00000000000dc000 - 0000000000100000
[    0.000000] Allocating PCI resources starting at 80000000 (gap: 80000000:60000000)
[    0.000000] Booting paravirtualized kernel on bare hardware
[    0.000000] setup_percpu: NR_CPUS:32 nr_cpumask_bits:32 nr_cpu_ids:1 nr_node_ids:1
[    0.000000] PERCPU: Embedded 14 pages/cpu @c2800000 s34260 r0 d23084 u4194304
[    0.000000] pcpu-alloc: s34260 r0 d23084 u4194304 alloc=1*4194304
[    0.000000] pcpu-alloc: [0] 0 
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 519729
[    0.000000] Kernel command line: root=/dev/mapper/vg-os11.2 resume=/dev/mapper/cr_sda10 splash=silent quiet vga=0x314
[    0.000000] bootsplash: silent mode.
[    0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Enabling fast FPU save and restore... done.
[    0.000000] Enabling unmasked SIMD FPU exception support... done.
[    0.000000] Initializing CPU#0
[    0.000000] Subtract (46 early reservations)
[    0.000000]   #1 [0000001000 - 0000002000]   EX TRAMPOLINE
[    0.000000]   #2 [0000200000 - 00009f1b04]   TEXT DATA BSS
[    0.000000]   #3 [000009f800 - 0000100000]   BIOS reserved
[    0.000000]   #4 [00009f2000 - 00009f5140]             BRK
[    0.000000]   #5 [0000010000 - 0000011000]      TRAMPOLINE
[    0.000000]   #6 [0000011000 - 0000015000]     ACPI WAKEUP
[    0.000000]   #7 [0000015000 - 0000016000]         PGTABLE
[    0.000000]   #8 [00009f6000 - 00015a5000]     NEW RAMDISK
[    0.000000]   #9 [00015a5000 - 00015a6000]         BOOTMEM
[    0.000000]   #10 [00015a6000 - 00025a6000]         BOOTMEM
[    0.000000]   #11 [00025a6000 - 00025a6004]         BOOTMEM
[    0.000000]   #12 [00025a6040 - 00025a6100]         BOOTMEM
[    0.000000]   #13 [00025a6100 - 00025a6154]         BOOTMEM
[    0.000000]   #14 [00025a6180 - 00025a9180]         BOOTMEM
[    0.000000]   #15 [00025a9180 - 00025a91f0]         BOOTMEM
[    0.000000]   #16 [00025a9200 - 00025af200]         BOOTMEM
[    0.000000]   #17 [00025af200 - 00025af225]         BOOTMEM
[    0.000000]   #18 [00025af240 - 00025af267]         BOOTMEM
[    0.000000]   #19 [00025af280 - 00025af408]         BOOTMEM
[    0.000000]   #20 [00025af440 - 00025af480]         BOOTMEM
[    0.000000]   #21 [00025af480 - 00025af4c0]         BOOTMEM
[    0.000000]   #22 [00025af4c0 - 00025af500]         BOOTMEM
[    0.000000]   #23 [00025af500 - 00025af540]         BOOTMEM
[    0.000000]   #24 [00025af540 - 00025af580]         BOOTMEM
[    0.000000]   #25 [00025af580 - 00025af5c0]         BOOTMEM
[    0.000000]   #26 [00025af5c0 - 00025af600]         BOOTMEM
[    0.000000]   #27 [00025af600 - 00025af640]         BOOTMEM
[    0.000000]   #28 [00025af640 - 00025af680]         BOOTMEM
[    0.000000]   #29 [00025af680 - 00025af6c0]         BOOTMEM
[    0.000000]   #30 [00025af6c0 - 00025af700]         BOOTMEM
[    0.000000]   #31 [00025af700 - 00025af740]         BOOTMEM
[    0.000000]   #32 [00025af740 - 00025af780]         BOOTMEM
[    0.000000]   #33 [00025af780 - 00025af790]         BOOTMEM
[    0.000000]   #34 [00025af7c0 - 00025af815]         BOOTMEM
[    0.000000]   #35 [00025af840 - 00025af895]         BOOTMEM
[    0.000000]   #36 [0002800000 - 000280e000]         BOOTMEM
[    0.000000]   #37 [00025b18c0 - 00025b18c4]         BOOTMEM
[    0.000000]   #38 [00025b1900 - 00025b1904]         BOOTMEM
[    0.000000]   #39 [00025b1940 - 00025b1944]         BOOTMEM
[    0.000000]   #40 [00025b1980 - 00025b1984]         BOOTMEM
[    0.000000]   #41 [00025b19c0 - 00025b1a70]         BOOTMEM
[    0.000000]   #42 [00025b1a80 - 00025b1b28]         BOOTMEM
[    0.000000]   #43 [00025b1b40 - 00025b5b40]         BOOTMEM
[    0.000000]   #44 [00025b5b40 - 0002635b40]         BOOTMEM
[    0.000000]   #45 [0002635b40 - 0002675b40]         BOOTMEM
[    0.000000] Initializing HighMem for node 0 (000377fe:0007fea0)
[    0.000000] Memory: 2057880k/2095744k available (3848k kernel code, 37412k reserved, 2861k data, 408k init, 1186440k highmem)
[    0.000000] virtual kernel memory layout:
[    0.000000]     fixmap  : 0xffd33000 - 0xfffff000   (2864 kB)
[    0.000000]     pkmap   : 0xff800000 - 0xffc00000   (4096 kB)
[    0.000000]     vmalloc : 0xf7ffe000 - 0xff7fe000   ( 120 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xf77fe000   ( 887 MB)
[    0.000000]       .init : 0xc088e000 - 0xc08f4000   ( 408 kB)
[    0.000000]       .data : 0xc05c20f0 - 0xc088d8a8   (2861 kB)
[    0.000000]       .text : 0xc0200000 - 0xc05c20f0   (3848 kB)
[    0.000000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[    0.000000] Hierarchical RCU implementation.
[    0.000000] NR_IRQS:2304 nr_irqs:256
[    0.000000] Console: colour dummy device 80x25
[    0.000000] console [tty0] enabled
[    0.000000] hpet clockevent registered
[    0.000000] Fast TSC calibration using PIT
[    0.000000] Detected 2127.893 MHz processor.
[    0.004007] Calibrating delay loop (skipped), value calculated using timer frequency.. 4255.78 BogoMIPS (lpj=8511572)
[    0.004065] kdb version 4.4 by Keith Owens, Scott Lurndal. Copyright SGI, All Rights Reserved
[    0.004130] Security Framework initialized
[    0.004161] AppArmor: AppArmor initialized
[    0.004178] Mount-cache hash table entries: 512
[    0.004313] Initializing cgroup subsys ns
[    0.004319] Initializing cgroup subsys cpuacct
[    0.004323] Initializing cgroup subsys memory
[    0.004333] Initializing cgroup subsys devices
[    0.004337] Initializing cgroup subsys freezer
[    0.004339] Initializing cgroup subsys net_cls
[    0.004341] Initializing cgroup subsys blkio
[    0.004380] mce: CPU supports 5 MCE banks
[    0.004390] CPU0: Thermal monitoring enabled (TM2)
[    0.004402] Performance Events: p6 PMU driver.
[    0.004409] ... version:                0
[    0.004410] ... bit width:              32
[    0.004412] ... generic registers:      2
[    0.004414] ... value mask:             00000000ffffffff
[    0.004415] ... max period:             000000007fffffff
[    0.004417] ... fixed-purpose events:   0
[    0.004419] ... event mask:             0000000000000003
[    0.004424] Checking 'hlt' instruction... OK.
[    0.020416] SMP alternatives: switching to UP code
[    0.024299] Freeing SMP alternatives: 28k freed
[    0.024355] Unpacking initramfs...
[    0.324089] Freeing initrd memory: 11964k freed
[    0.333569] ACPI: Core revision 20100121
[    0.348097] Enabling APIC mode:  Flat.  Using 1 I/O APICs
[    0.348476] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[    0.388625] CPU0: Intel(R) Pentium(R) M processor 2.13GHz stepping 08
[    0.392000] Brought up 1 CPUs
[    0.392000] Total of 1 processors activated (4255.78 BogoMIPS).
[    0.392000] devtmpfs: initialized
[    0.392000] regulator: core version 0.5
[    0.392000] regulator: dummy: 
[    0.392000] Time: 22:50:19  Date: 11/23/10
[    0.392000] NET: Registered protocol family 16
[    0.392000] ACPI: bus type pci registered
[    0.392000] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
[    0.392000] PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in E820
[    0.392000] PCI: Using MMCONFIG for extended config space
[    0.392000] PCI: Using configuration type 1 for base access
[    0.392000] bio: create slab <bio-0> at 0
[    0.392000] ACPI: EC: Look up EC in DSDT
[    0.394592] ACPI: Interpreter enabled
[    0.394592] ACPI: (supports S0 S3 S4 S5)
[    0.394592] ACPI: Using IOAPIC for interrupt routing
[    0.400391] ACPI: EC: GPE = 0x17, I/O: command/status = 0x66, data = 0x62
[    0.400453] ACPI: Power Resource [CFAN] (on)
[    0.401143] ACPI: ACPI Dock Station Driver: 1 docks/bays found
[    0.401147] PCI: Ignoring host bridge windows from ACPI; if necessary, use "pci=use_crs" and report a bug
[    0.401785] ACPI: PCI Root Bridge [PCI0] (0000:00)
[    0.403034] pci_root PNP0A08:00: host bridge window [io  0x0000-0x0cf7] (ignored)
[    0.403037] pci_root PNP0A08:00: host bridge window [io  0x0d00-0xffff] (ignored)
[    0.403039] pci_root PNP0A08:00: host bridge window [mem 0x000a0000-0x000bffff] (ignored)
[    0.403042] pci_root PNP0A08:00: host bridge window [mem 0x000d4000-0x000d7fff] (ignored)
[    0.403045] pci_root PNP0A08:00: host bridge window [mem 0x000d8000-0x000dbfff] (ignored)
[    0.403048] pci_root PNP0A08:00: host bridge window [mem 0x80000000-0xfebfffff] (ignored)
[    0.403121] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
[    0.403125] pci 0000:00:01.0: PME# disabled
[    0.403240] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[    0.403244] pci 0000:00:1c.0: PME# disabled
[    0.403306] pci 0000:00:1d.0: reg 20: [io  0x1800-0x181f]
[    0.403364] pci 0000:00:1d.1: reg 20: [io  0x1820-0x183f]
[    0.403420] pci 0000:00:1d.2: reg 20: [io  0x1840-0x185f]
[    0.403477] pci 0000:00:1d.3: reg 20: [io  0x1860-0x187f]
[    0.403530] pci 0000:00:1d.7: reg 10: [mem 0xc0000000-0xc00003ff]
[    0.403587] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
[    0.403592] pci 0000:00:1d.7: PME# disabled
[    0.403685] pci 0000:00:1e.2: reg 10: [io  0x1c00-0x1cff]
[    0.403693] pci 0000:00:1e.2: reg 14: [io  0x1880-0x18bf]
[    0.403700] pci 0000:00:1e.2: reg 18: [mem 0xc0000800-0xc00009ff]
[    0.403707] pci 0000:00:1e.2: reg 1c: [mem 0xc0000400-0xc00004ff]
[    0.403743] pci 0000:00:1e.2: PME# supported from D0 D3hot D3cold
[    0.403747] pci 0000:00:1e.2: PME# disabled
[    0.403778] pci 0000:00:1e.3: reg 10: [io  0x2400-0x24ff]
[    0.403785] pci 0000:00:1e.3: reg 14: [io  0x2000-0x207f]
[    0.403830] pci 0000:00:1e.3: PME# supported from D0 D3hot D3cold
[    0.403835] pci 0000:00:1e.3: PME# disabled
[    0.403916] pci 0000:00:1f.0: quirk: [io  0x1000-0x107f] claimed by ICH6 ACPI/GPIO/TCO
[    0.403921] pci 0000:00:1f.0: quirk: [io  0x1180-0x11bf] claimed by ICH6 GPIO
[    0.403925] pci 0000:00:1f.0: LPC Generic IO decode 1 PIO at 0680-06ff
[    0.403929] pci 0000:00:1f.0: LPC Generic IO decode 2 PIO at 1640-164f
[    0.403964] pci 0000:00:1f.2: reg 10: [io  0x0000-0x0007]
[    0.403972] pci 0000:00:1f.2: reg 14: [io  0x0000-0x0003]
[    0.403979] pci 0000:00:1f.2: reg 18: [io  0x0000-0x0007]
[    0.403986] pci 0000:00:1f.2: reg 1c: [io  0x0000-0x0003]
[    0.403993] pci 0000:00:1f.2: reg 20: [io  0x18e0-0x18ef]
[    0.404029] pci 0000:00:1f.2: PME# supported from D3hot
[    0.404034] pci 0000:00:1f.2: PME# disabled
[    0.404090] pci 0000:00:1f.3: reg 20: [io  0x20a0-0x20bf]
[    0.404159] pci 0000:01:00.0: reg 10: [mem 0xd0000000-0xd7ffffff pref]
[    0.404164] pci 0000:01:00.0: reg 14: [io  0x3000-0x30ff]
[    0.404170] pci 0000:01:00.0: reg 18: [mem 0xc0100000-0xc010ffff]
[    0.404183] pci 0000:01:00.0: reg 30: [mem 0x00000000-0x0001ffff pref]
[    0.404199] pci 0000:01:00.0: supports D1 D2
[    0.404209] pci 0000:01:00.0: disabling ASPM on pre-1.1 PCIe device.  You can enable it with 'pcie_aspm=force'
[    0.404217] pci 0000:00:01.0: PCI bridge to [bus 01-01]
[    0.404220] pci 0000:00:01.0:   bridge window [io  0x3000-0x3fff]
[    0.404224] pci 0000:00:01.0:   bridge window [mem 0xc0100000-0xc01fffff]
[    0.404227] pci 0000:00:01.0:   bridge window [mem 0xd0000000-0xd7ffffff pref]
[    0.404280] pci 0000:00:1c.0: PCI bridge to [bus 02-02]
[    0.404284] pci 0000:00:1c.0:   bridge window [io  0x4000-0x4fff]
[    0.404289] pci 0000:00:1c.0:   bridge window [mem 0xc4000000-0xc7ffffff]
[    0.404296] pci 0000:00:1c.0:   bridge window [mem 0xd8000000-0xdbffffff 64bit pref]
[    0.404383] pci 0000:06:05.0: reg 10: [mem 0xc8000000-0xc800ffff]
[    0.404472] pci 0000:06:05.0: PME# supported from D3hot D3cold
[    0.404477] pci 0000:06:05.0: PME# disabled
[    0.404524] pci 0000:06:07.0: reg 10: [mem 0xc8010000-0xc8010fff]
[    0.404595] pci 0000:06:07.0: PME# supported from D0 D3hot D3cold
[    0.404600] pci 0000:06:07.0: PME# disabled
[    0.404645] pci 0000:06:09.0: reg 10: [mem 0x00000000-0x00000fff]
[    0.404671] pci 0000:06:09.0: supports D1 D2
[    0.404673] pci 0000:06:09.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.404679] pci 0000:06:09.0: PME# disabled
[    0.404720] pci 0000:06:09.1: reg 10: [mem 0xc8011000-0xc80117ff]
[    0.404788] pci 0000:06:09.1: PME# supported from D0 D3hot D3cold
[    0.404794] pci 0000:06:09.1: PME# disabled
[    0.404834] pci 0000:06:09.2: reg 10: [mem 0xc8011800-0xc80118ff]
[    0.404902] pci 0000:06:09.2: supports D1 D2
[    0.404904] pci 0000:06:09.2: PME# supported from D0 D1 D2 D3hot D3cold
[    0.404909] pci 0000:06:09.2: PME# disabled
[    0.404950] pci 0000:06:09.3: reg 10: [mem 0xc8011c00-0xc8011cff]
[    0.405018] pci 0000:06:09.3: supports D1 D2
[    0.405020] pci 0000:06:09.3: PME# supported from D0 D1 D2 D3hot D3cold
[    0.405026] pci 0000:06:09.3: PME# disabled
[    0.405081] pci 0000:00:1e.0: PCI bridge to [bus 06-06] (subtractive decode)
[    0.405086] pci 0000:00:1e.0:   bridge window [io  0xf000-0x0000] (disabled)
[    0.405091] pci 0000:00:1e.0:   bridge window [mem 0xc8000000-0xc80fffff]
[    0.405098] pci 0000:00:1e.0:   bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
[    0.405101] pci 0000:00:1e.0:   bridge window [io  0x0000-0xffff] (subtractive decode)
[    0.405104] pci 0000:00:1e.0:   bridge window [mem 0x00000000-0xffffffff] (subtractive decode)
[    0.405156] pci_bus 0000:07: [bus 07-0a] partially hidden behind transparent bridge 0000:06 [bus 06-06]
[    0.405174] pci_bus 0000:00: on NUMA node 0
[    0.405178] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[    0.405379] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEGP._PRT]
[    0.405469] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP01._PRT]
[    0.405572] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT]
[    0.411640] ACPI: PCI Interrupt Link [LNKA] (IRQs *11)
[    0.411739] ACPI: PCI Interrupt Link [LNKB] (IRQs *10)
[    0.411839] ACPI: PCI Interrupt Link [LNKC] (IRQs *5)
[    0.411937] ACPI: PCI Interrupt Link [LNKD] (IRQs *5)
[    0.412041] ACPI: PCI Interrupt Link [LNKE] (IRQs *11)
[    0.412139] ACPI: PCI Interrupt Link [LNKF] (IRQs 10) *0, disabled.
[    0.412238] ACPI: PCI Interrupt Link [LNKG] (IRQs *5)
[    0.412336] ACPI: PCI Interrupt Link [LNKH] (IRQs *5)
[    0.412464] vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none
[    0.412469] vgaarb: loaded
[    0.412535] PCI: Using ACPI for IRQ routing
[    0.412537] PCI: pci_cache_line_size set to 64 bytes
[    0.412618] reserve RAM buffer: 000000000009f800 - 000000000009ffff 
[    0.412621] reserve RAM buffer: 000000007fea0000 - 000000007fffffff 
[    0.412706] NetLabel: Initializing
[    0.412708] NetLabel:  domain hash size = 128
[    0.412709] NetLabel:  protocols = UNLABELED CIPSOv4
[    0.412721] NetLabel:  unlabeled traffic allowed by default
[    0.412727] HPET: 3 timers in total, 0 timers will be used for per-cpu timer
[    0.412734] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[    0.412738] hpet0: 3 comparators, 64-bit 14.318180 MHz counter
[    0.416018] Switching to clocksource tsc
[    0.417370] AppArmor: AppArmor Filesystem Enabled
[    0.417385] pnp: PnP ACPI init
[    0.417398] ACPI: bus type pnp registered
[    0.419736] pnp: PnP ACPI: found 11 devices
[    0.419739] ACPI: ACPI bus type pnp unregistered
[    0.419742] PnPBIOS: Disabled by ACPI PNP
[    0.419754] system 00:01: [mem 0xe0000000-0xefffffff] has been reserved
[    0.419757] system 00:01: [mem 0xf0000000-0xf0003fff] has been reserved
[    0.419760] system 00:01: [mem 0xf0004000-0xf0004fff] has been reserved
[    0.419763] system 00:01: [mem 0xf0005000-0xf0005fff] has been reserved
[    0.419765] system 00:01: [mem 0xf0008000-0xf000bfff] has been reserved
[    0.419768] system 00:01: [mem 0xfed20000-0xfed8ffff] has been reserved
[    0.419775] system 00:06: [io  0x0680-0x06df] has been reserved
[    0.419778] system 00:06: [io  0x06f0-0x06ff] has been reserved
[    0.419780] system 00:06: [io  0x0800-0x080f] has been reserved
[    0.419783] system 00:06: [io  0x0900-0x090f] has been reserved
[    0.419786] system 00:06: [io  0x1000-0x107f] has been reserved
[    0.419788] system 00:06: [io  0x1180-0x11bf] has been reserved
[    0.419791] system 00:06: [io  0x1640-0x164f] has been reserved
[    0.454559] pci 0000:00:1e.0: BAR 15: assigned [mem 0x80000000-0x83ffffff pref]
[    0.454562] pci 0000:00:1e.0: BAR 13: assigned [io  0x5000-0x5fff]
[    0.454566] pci 0000:01:00.0: BAR 6: assigned [mem 0xc0120000-0xc013ffff pref]
[    0.454569] pci 0000:00:01.0: PCI bridge to [bus 01-01]
[    0.454572] pci 0000:00:01.0:   bridge window [io  0x3000-0x3fff]
[    0.454576] pci 0000:00:01.0:   bridge window [mem 0xc0100000-0xc01fffff]
[    0.454579] pci 0000:00:01.0:   bridge window [mem 0xd0000000-0xd7ffffff pref]
[    0.454583] pci 0000:00:1c.0: PCI bridge to [bus 02-02]
[    0.454587] pci 0000:00:1c.0:   bridge window [io  0x4000-0x4fff]
[    0.454593] pci 0000:00:1c.0:   bridge window [mem 0xc4000000-0xc7ffffff]
[    0.454598] pci 0000:00:1c.0:   bridge window [mem 0xd8000000-0xdbffffff 64bit pref]
[    0.454607] pci 0000:06:09.0: BAR 15: assigned [mem 0x80000000-0x83ffffff pref]
[    0.454610] pci 0000:06:09.0: BAR 16: assigned [mem 0x84000000-0x87ffffff]
[    0.454613] pci 0000:06:09.0: BAR 0: assigned [mem 0xc8012000-0xc8012fff]
[    0.454620] pci 0000:06:09.0: BAR 0: set to [mem 0xc8012000-0xc8012fff] (PCI address [0xc8012000-0xc8012fff]
[    0.454623] pci 0000:06:09.0: BAR 13: assigned [io  0x5000-0x50ff]
[    0.454625] pci 0000:06:09.0: BAR 14: assigned [io  0x5400-0x54ff]
[    0.454628] pci 0000:06:09.0: CardBus bridge to [bus 07-0a]
[    0.454630] pci 0000:06:09.0:   bridge window [io  0x5000-0x50ff]
[    0.454635] pci 0000:06:09.0:   bridge window [io  0x5400-0x54ff]
[    0.454641] pci 0000:06:09.0:   bridge window [mem 0x80000000-0x83ffffff pref]
[    0.454647] pci 0000:06:09.0:   bridge window [mem 0x84000000-0x87ffffff]
[    0.454653] pci 0000:00:1e.0: PCI bridge to [bus 06-06]
[    0.454656] pci 0000:00:1e.0:   bridge window [io  0x5000-0x5fff]
[    0.454662] pci 0000:00:1e.0:   bridge window [mem 0xc8000000-0xc80fffff]
[    0.454667] pci 0000:00:1e.0:   bridge window [mem 0x80000000-0x83ffffff pref]
[    0.454681]   alloc irq_desc for 16 on node -1
[    0.454683]   alloc kstat_irqs on node -1
[    0.454688] pci 0000:00:01.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    0.454693] pci 0000:00:01.0: setting latency timer to 64
[    0.454755] pci 0000:00:1c.0: power state changed by ACPI to D0
[    0.454791] pci 0000:00:1c.0: power state changed by ACPI to D0
[    0.454797]   alloc irq_desc for 17 on node -1
[    0.454798]   alloc kstat_irqs on node -1
[    0.454802] pci 0000:00:1c.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[    0.454807] pci 0000:00:1c.0: setting latency timer to 64
[    0.454814] pci 0000:00:1e.0: setting latency timer to 64
[    0.454852] pci 0000:06:09.0: power state changed by ACPI to D0
[    0.454889] pci 0000:06:09.0: power state changed by ACPI to D0
[    0.454896] pci 0000:06:09.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    0.454903] pci_bus 0000:00: resource 0 [io  0x0000-0xffff]
[    0.454905] pci_bus 0000:00: resource 1 [mem 0x00000000-0xffffffff]
[    0.454908] pci_bus 0000:01: resource 0 [io  0x3000-0x3fff]
[    0.454910] pci_bus 0000:01: resource 1 [mem 0xc0100000-0xc01fffff]
[    0.454913] pci_bus 0000:01: resource 2 [mem 0xd0000000-0xd7ffffff pref]
[    0.454915] pci_bus 0000:02: resource 0 [io  0x4000-0x4fff]
[    0.454917] pci_bus 0000:02: resource 1 [mem 0xc4000000-0xc7ffffff]
[    0.454920] pci_bus 0000:02: resource 2 [mem 0xd8000000-0xdbffffff 64bit pref]
[    0.454922] pci_bus 0000:06: resource 0 [io  0x5000-0x5fff]
[    0.454925] pci_bus 0000:06: resource 1 [mem 0xc8000000-0xc80fffff]
[    0.454927] pci_bus 0000:06: resource 2 [mem 0x80000000-0x83ffffff pref]
[    0.454929] pci_bus 0000:06: resource 4 [io  0x0000-0xffff]
[    0.454932] pci_bus 0000:06: resource 5 [mem 0x00000000-0xffffffff]
[    0.454934] pci_bus 0000:07: resource 0 [io  0x5000-0x50ff]
[    0.454937] pci_bus 0000:07: resource 1 [io  0x5400-0x54ff]
[    0.454939] pci_bus 0000:07: resource 2 [mem 0x80000000-0x83ffffff pref]
[    0.454942] pci_bus 0000:07: resource 3 [mem 0x84000000-0x87ffffff]
[    0.454979] NET: Registered protocol family 2
[    0.455040] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.455285] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[    0.456183] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[    0.456761] TCP: Hash tables configured (established 131072 bind 65536)
[    0.456765] TCP reno registered
[    0.456770] UDP hash table entries: 512 (order: 2, 16384 bytes)
[    0.456792] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[    0.456953] NET: Registered protocol family 1
[    0.457086] pci 0000:01:00.0: Boot video device
[    0.457107] PCI: CLS 32 bytes, default 64
[    0.457333] Simple Boot Flag at 0x36 set to 0x1
[    0.457512] Scanning for low memory corruption every 60 seconds
[    0.457637] audit: initializing netlink socket (disabled)
[    0.457650] type=2000 audit(1290552619.455:1): initialized
[    0.471814] highmem bounce pool size: 64 pages
[    0.471821] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[    0.471926] VFS: Disk quotas dquot_6.5.2
[    0.471951] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    0.472079] msgmni has been set to 431
[    0.472174] alg: No test for stdrng (krng)
[    0.472219] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
[    0.472223] io scheduler noop registered
[    0.472225] io scheduler deadline registered
[    0.472238] io scheduler cfq registered (default)
[    0.472389] pcieport 0000:00:01.0: setting latency timer to 64
[    0.472411]   alloc irq_desc for 24 on node -1
[    0.472413]   alloc kstat_irqs on node -1
[    0.472423] pcieport 0000:00:01.0: irq 24 for MSI/MSI-X
[    0.472474] pcieport 0000:00:1c.0: setting latency timer to 64
[    0.472514]   alloc irq_desc for 25 on node -1
[    0.472515]   alloc kstat_irqs on node -1
[    0.472523] pcieport 0000:00:1c.0: irq 25 for MSI/MSI-X
[    0.472617] pcieport 0000:00:01.0: Requesting control of PCIe PME from ACPI BIOS
[    0.472623] pcieport 0000:00:01.0: Failed to receive control of PCIe PME service: no _OSC support
[    0.472628] pcie_pme: probe of 0000:00:01.0:pcie01 failed with error -13
[    0.472632] pcieport 0000:00:1c.0: Requesting control of PCIe PME from ACPI BIOS
[    0.472635] pcieport 0000:00:1c.0: Failed to receive control of PCIe PME service: no _OSC support
[    0.472638] pcie_pme: probe of 0000:00:1c.0:pcie01 failed with error -13
[    0.472662] pci-stub: invalid id string ""
[    0.472806] vesafb: framebuffer at 0xd0000000, mapped to 0xf8080000, using 1875k, total 16384k
[    0.472809] vesafb: mode is 800x600x16, linelength=1600, pages=16
[    0.472811] vesafb: protected mode interface info at c000:af18
[    0.472814] vesafb: pmi: set display start = c00cafa6, set palette = c00cafe6
[    0.472816] vesafb: scrolling: redraw
[    0.472819] vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
[    0.473370] bootsplash 3.1.6-2004/03/31: looking for picture...
[    0.473374] bootsplash: silentjpeg size 200657 bytes
[    0.509021] bootsplash: silentjpeg size 127397 bytes
[    0.520097] bootsplash: ...found (800x600, 63072 bytes, v3).
[    0.556773] Console: switching to colour frame buffer device 96x33
[    0.592891] fb0: VESA VGA frame buffer device
[    0.592959] isapnp: Scanning for PnP cards...
[    0.903408] isapnp: No Plug & Play device found
[    0.904877] Non-volatile memory driver v1.3
[    0.904879] Linux agpgart interface v0.103
[    0.904908] Serial: 8250/16550 driver, 8 ports, IRQ sharing disabled
[    0.905352]   alloc irq_desc for 20 on node -1
[    0.905355]   alloc kstat_irqs on node -1
[    0.905365] serial 0000:00:1e.3: PCI INT B -> GSI 20 (level, low) -> IRQ 20
[    0.905372] serial 0000:00:1e.3: PCI INT B disabled
[    0.905434] Fixed MDIO Bus: probed
[    0.905478] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[    0.908418] i8042.c: Detected active multiplexing controller, rev 1.1.
[    0.909836] serio: i8042 KBD port at 0x60,0x64 irq 1
[    0.909842] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[    0.909845] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[    0.909847] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[    0.909850] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[    0.909902] mice: PS/2 mouse device common for all mice
[    0.910024] cpuidle: using governor ladder
[    0.910026] cpuidle: using governor menu
[    1.072832] TCP cubic registered
[    1.072867] NET: Registered protocol family 10
[    1.073161] lo: Disabled Privacy Extensions
[    1.073369] Using IPI No-Shortcut mode
[    1.073437] PM: Checking image partition /dev/mapper/cr_sda10
[    1.087738] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
[    1.896031] Synaptics Touchpad, model: 1, fw: 6.1, id: 0x2580b1, caps: 0xa04713/0x200000/0x0
[    1.931156] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio4/input/input1
[    2.122177] PM: Resume from disk failed.
[    2.122193] registered taskstats version 1
[    2.122443]   Magic number: 2:881:856
[    2.122600] Freeing unused kernel memory: 408k freed
[    2.122808] Write protecting the kernel text: 3852k
[    2.122848] Write protecting the kernel read-only data: 2600k
[    2.164891] SCSI subsystem initialized
[    2.187748] libata version 3.00 loaded.
[    2.192766] ahci 0000:00:1f.2: version 3.0
[    2.192789]   alloc irq_desc for 19 on node -1
[    2.192791]   alloc kstat_irqs on node -1
[    2.192800] ahci 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[    2.192814] ahci 0000:00:1f.2: PCI INT B disabled
[    2.192817] ahci: probe of 0000:00:1f.2 failed with error -22
[    2.200098] thermal LNXTHERM:01: registered as thermal_zone0
[    2.200112] ACPI: Thermal Zone [THRM] (72 C)
[    2.211863] processor_driver-0392 [00] processor_get_info    : Bus mastering arbitration control present
[    2.211888] processor_driver-0474 [00] processor_get_info    : Processor [0:0]
[    2.211899] processor_throttling-1141 [00] processor_get_throttli: pblk_address[0x00001010] duty_offset[3] duty_width[1]
[    2.211906] processor_throttling-1187 [00] processor_get_throttli: Found 2 throttling states
[    2.211912] processor_throttling-0657 [00] processor_get_throttli: Throttling state is T0 (1000% throttling applied)
[    2.212065] processor_idle-0526 [00] processor_get_power_in: Found 3 power states
[    2.212070] Marking TSC unstable due to TSC halts in idle
[    2.212220] processor_throttling-0218 [00] processor_throttling_i: Assume no T-state coordination
[    2.212593] Switching to clocksource hpet
[    2.214785] ACPI: Fan [FAN1] (on)
[    2.224625] device-mapper: uevent: version 1.0.3
[    2.224731] device-mapper: ioctl: 4.17.0-ioctl (2010-03-05) initialised: dm-devel@redhat.com
[    2.234628] udev: starting version 157
[    2.285309] usbcore: registered new interface driver usbfs
[    2.285338] usbcore: registered new interface driver hub
[    2.433490] ata_piix 0000:00:1f.2: version 2.13
[    2.433512] ata_piix 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[    2.433518] ata_piix 0000:00:1f.2: MAP [ P0 P2 IDE IDE ]
[    2.433562] ata_piix 0000:00:1f.2: setting latency timer to 64
[    2.477584] [drm] Initialized drm 1.1.0 20060810
[    2.477843] scsi0 : ata_piix
[    2.480239] rtc_cmos 00:07: rtc core: registered rtc_cmos as rtc0
[    2.480276] rtc0: alarms up to one month, y3k, 242 bytes nvram, hpet irqs
[    2.480780] scsi1 : ata_piix
[    2.482025] ata1: SATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0x18e0 irq 14
[    2.482028] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x18e8 irq 15
[    2.482604] usbcore: registered new device driver usb
[    2.493828] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    2.493865]   alloc irq_desc for 23 on node -1
[    2.493867]   alloc kstat_irqs on node -1
[    2.493875] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[    2.493892] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[    2.493895] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[    2.493920] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
[    2.493950] ehci_hcd 0000:00:1d.7: debug port 1
[    2.497851] ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
[    2.497871] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xc0000000
[    2.512035] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[    2.512079] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    2.512082] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.512085] usb usb1: Product: EHCI Host Controller
[    2.512087] usb usb1: Manufacturer: Linux 2.6.34-12-default ehci_hcd
[    2.512089] usb usb1: SerialNumber: 0000:00:1d.7
[    2.512214] hub 1-0:1.0: USB hub found
[    2.512219] hub 1-0:1.0: 8 ports detected
[    2.539655] uhci_hcd: USB Universal Host Controller Interface driver
[    2.539710] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[    2.539719] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[    2.539723] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[    2.539736] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
[    2.539767] uhci_hcd 0000:00:1d.0: irq 23, io base 0x00001800
[    2.539808] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[    2.539811] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.539813] usb usb2: Product: UHCI Host Controller
[    2.539815] usb usb2: Manufacturer: Linux 2.6.34-12-default uhci_hcd
[    2.539817] usb usb2: SerialNumber: 0000:00:1d.0
[    2.539927] hub 2-0:1.0: USB hub found
[    2.539932] hub 2-0:1.0: 2 ports detected
[    2.539991] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[    2.540026] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[    2.540029] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[    2.540037] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
[    2.540075] uhci_hcd 0000:00:1d.1: irq 19, io base 0x00001820
[    2.540105] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[    2.540107] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.540110] usb usb3: Product: UHCI Host Controller
[    2.540112] usb usb3: Manufacturer: Linux 2.6.34-12-default uhci_hcd
[    2.540114] usb usb3: SerialNumber: 0000:00:1d.1
[    2.540189] hub 3-0:1.0: USB hub found
[    2.540193] hub 3-0:1.0: 2 ports detected
[    2.540247]   alloc irq_desc for 18 on node -1
[    2.540249]   alloc kstat_irqs on node -1
[    2.540256] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[    2.540262] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[    2.540266] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[    2.540272] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
[    2.540304] uhci_hcd 0000:00:1d.2: irq 18, io base 0x00001840
[    2.540334] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[    2.540337] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.540339] usb usb4: Product: UHCI Host Controller
[    2.540341] usb usb4: Manufacturer: Linux 2.6.34-12-default uhci_hcd
[    2.540343] usb usb4: SerialNumber: 0000:00:1d.2
[    2.540423] hub 4-0:1.0: USB hub found
[    2.540427] hub 4-0:1.0: 2 ports detected
[    2.540476] uhci_hcd 0000:00:1d.3: PCI INT D -> GSI 16 (level, low) -> IRQ 16
[    2.540483] uhci_hcd 0000:00:1d.3: setting latency timer to 64
[    2.540487] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[    2.540492] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
[    2.540526] uhci_hcd 0000:00:1d.3: irq 16, io base 0x00001860
[    2.540557] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
[    2.540559] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.540561] usb usb5: Product: UHCI Host Controller
[    2.540563] usb usb5: Manufacturer: Linux 2.6.34-12-default uhci_hcd
[    2.540565] usb usb5: SerialNumber: 0000:00:1d.3
[    2.540640] hub 5-0:1.0: USB hub found
[    2.540644] hub 5-0:1.0: 2 ports detected
[    2.644729] ata2.00: ATAPI: MATSHITADVD-RAM UJ-822S, 1.00, max UDMA/33
[    2.645241] ata1.00: failed to set max address (err_mask=0x1)
[    2.645244] ata1.00: device aborted resize (155490289 -> 156301488), skipping HPA handling
[    2.645250] ata1.00: ATA-7: FUJITSU MHT2080BH, 0000104A, max UDMA/100
[    2.645253] ata1.00: 155490289 sectors, multi 16: LBA48 NCQ (depth 0/32)
[    2.660584] ata2.00: configured for UDMA/33
[    2.660676] ata1.00: configured for UDMA/100
[    2.660804] scsi 0:0:0:0: Direct-Access     ATA      FUJITSU MHT2080B 0000 PQ: 0 ANSI: 5
[    2.663195] scsi 1:0:0:0: CD-ROM            MATSHITA DVD-RAM UJ-822S  1.00 PQ: 0 ANSI: 5
[    2.687073] sd 0:0:0:0: [sda] 155490289 512-byte logical blocks: (79.6 GB/74.1 GiB)
[    2.687144] sd 0:0:0:0: [sda] Write Protect is off
[    2.687147] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    2.687167] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    2.687292]  sda:
[    2.713586] [drm] radeon defaulting to kernel modesetting.
[    2.713590] [drm] radeon kernel modesetting enabled.
[    2.713658] radeon 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    2.713663] radeon 0000:01:00.0: setting latency timer to 64
[    2.715743] [drm] initializing kernel modesetting (RV410 0x1002:0x5652).
[    2.716537] [drm] register mmio base: 0xC0100000
[    2.716540] [drm] register mmio size: 65536
[    2.716690] ATOM BIOS: Samsung
[    2.716911] [drm] GPU reset succeed (RBBM_STATUS=0x00000140)
[    2.716920] [drm] Possible LM63 thermal controller at 0x4c
[    2.716965] [drm] 3 Power State(s)
[    2.716967] [drm] State 0 Battery 
[    2.716969] [drm] 	1 PCIE Lanes
[    2.716970] [drm] 	1 Clock Mode(s)
[    2.716972] [drm] 		0 engine/memory: 105000/120000
[    2.716974] [drm] State 1 Battery 
[    2.716975] [drm] 	1 PCIE Lanes
[    2.716977] [drm] 	1 Clock Mode(s)
[    2.716979] [drm] 		0 engine/memory: 210000/183000
[    2.716980] [drm] State 2 Default (default)
[    2.716982] [drm] 	16 PCIE Lanes
[    2.716983] [drm] 	1 Clock Mode(s)
[    2.716985] [drm] 		0 engine/memory: 350000/330000
[    2.716996] [drm] radeon: power management initialized
[    2.717000] [drm] Generation 2 PCI interface, using max accessible memory
[    2.717005] radeon 0000:01:00.0: VRAM: 128M 0xD0000000 - 0xD7FFFFFF (128M used)
[    2.717008] radeon 0000:01:00.0: GTT: 512M 0xB0000000 - 0xCFFFFFFF
[    2.717058]   alloc irq_desc for 26 on node -1
[    2.717061]   alloc kstat_irqs on node -1
[    2.717072] radeon 0000:01:00.0: irq 26 for MSI/MSI-X
[    2.717077] [drm] radeon: using MSI.
[    2.717105] [drm] radeon: irq initialized.
[    2.718003] [drm] Detected VRAM RAM=128M, BAR=128M
[    2.718007] [drm] RAM width 128bits DDR
[    2.718357] [TTM] Zone  kernel: Available graphics memory: 441920 kiB.
[    2.718360] [TTM] Zone highmem: Available graphics memory: 1035140 kiB.
[    2.718379] [drm] radeon: 128M of VRAM memory ready
[    2.718381] [drm] radeon: 512M of GTT memory ready.
[    2.718394] [drm] GART: num cpu pages 131072, num gpu pages 131072
[    2.720337] [drm] PCIE GART of 512M enabled (table at 0xD0040000).
[    2.720348] [drm] radeon: 2 quad pipes, 1 z pipes initialized.
[    2.720359] [drm] radeon: cp idle (0x10000C03)
[    2.720388] [drm] Loading R400 Microcode
[    2.720391] platform radeon_cp.0: firmware: requesting radeon/R420_cp.bin
[    2.723056] [drm] radeon: ring at 0x00000000B0000000
[    2.723079] [drm] ring test succeeded in 1 usecs
[    2.723221] [drm] radeon: ib pool ready.
[    2.723288] [drm] ib test succeeded in 0 usecs
[    2.723324] [drm] Default TV standard: PAL
[    2.723403] [drm] Default TV standard: PAL
[    2.723458] [drm] Radeon Display Connectors
[    2.723460] [drm] Connector 0:
[    2.723461] [drm]   VGA
[    2.723464] [drm]   DDC: 0x60 0x60 0x60 0x60 0x60 0x60 0x60 0x60
[    2.723466] [drm]   Encoders:
[    2.723467] [drm]     CRT1: INTERNAL_DAC1
[    2.723469] [drm] Connector 1:
[    2.723470] [drm]   LVDS
[    2.723471] [drm]   Encoders:
[    2.723472] [drm]     LCD1: INTERNAL_LVDS
[    2.723474] [drm] Connector 2:
[    2.723475] [drm]   S-video
[    2.723476] [drm]   Encoders:
[    2.723478] [drm]     TV1: INTERNAL_DAC2
[    2.723479] [drm] Connector 3:
[    2.723480] [drm]   DVI-D
[    2.723482] [drm]   HPD1
[    2.723484] [drm]   DDC: 0x64 0x64 0x64 0x64 0x64 0x64 0x64 0x64
[    2.723485] [drm]   Encoders:
[    2.723487] [drm]     DFP1: INTERNAL_TMDS1
[    2.876855]  sda1 sda2 sda3 sda4 < sda5
[    2.898764] [drm] fb mappable at 0xD00C0000
[    2.898766] [drm] vram apper at 0xD0000000
[    2.898768] [drm] size 7056000
[    2.898770] [drm] fb depth is 24
[    2.898771] [drm]    pitch is 6720
[    2.898777] fb: conflicting fb hw usage radeondrmfb vs VESA VGA - removing generic driver
[    2.898804] Console: switching to colour dummy device 80x25
[    3.048012]  sda6
[    3.048240] usb 1-2: new high speed USB device using ehci_hcd and address 2
[    3.369943] Console: switching to colour frame buffer device 206x61
[    3.452030] fb0: radeondrmfb frame buffer device
[    3.452034] registered panic notifier
[    3.452043] [drm] Initialized radeon 2.3.0 20080528 for 0000:01:00.0 on minor 0
[    3.452140]  sda7 sda8 sda9 sda10 >
[    3.503538] sd 0:0:0:0: [sda] Attached SCSI disk
[    3.530675] usb 1-2: New USB device found, idVendor=04b4, idProduct=6830
[    3.530680] usb 1-2: New USB device strings: Mfr=56, Product=58, SerialNumber=60
[    3.530682] usb 1-2: Product:  
[    3.530684] usb 1-2: Manufacturer:  
[    3.530686] usb 1-2: SerialNumber: D
[    3.992025] usb 3-2: new full speed USB device using uhci_hcd and address 2
[    4.155107] usb 3-2: New USB device found, idVendor=08ff, idProduct=5711
[    4.155111] usb 3-2: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[    4.155113] usb 3-2: Product: Fingerprint Sensor
[    4.396030] usb 4-1: new full speed USB device using uhci_hcd and address 2
[    4.428793] md: linear personality registered for level -1
[    4.595347] usb 4-1: New USB device found, idVendor=04e8, idProduct=7021
[    4.595351] usb 4-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[    5.905281] bootsplash: status on console 0 changed to on
[   20.605735] bootsplash: status on console 0 changed to on
[   20.692816] PM: Marking nosave pages: 000000000009f000 - 0000000000100000
[   20.692822] PM: Basic memory bitmaps created
[   20.706116] PM: Basic memory bitmaps freed
[   20.814565] PM: Starting manual resume from disk
[   20.814569] PM: Resume from partition 253:7
[   20.814571] PM: Checking hibernation image.
[   20.814919] PM: Error -22 checking image file
[   20.814920] PM: Resume from disk failed.
[   20.995551] EXT4-fs (dm-6): mounted filesystem with ordered data mode
[   23.435689] preloadtrace: systemtap: 1.1/0.147, base: fa415000, memory: 24data/38text/6ctx/13net/260alloc kb, probes: 34
[   25.971689] udev: starting version 157
[   26.024223] input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0D:00/input/input2
[   26.119616] i801_smbus 0000:00:1f.3: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[   26.119624] ACPI: resource 0000:00:1f.3 [io  0x20a0-0x20bf] conflicts with ACPI region SMBI [??? 0x000020a0-0x000020af flags 0x49]
[   26.119627] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[   26.150489] input: PC Speaker as /devices/platform/pcspkr/input/input3
[   26.223553] lib80211: common routines for IEEE802.11 drivers
[   26.223557] lib80211_crypt: registered algorithm 'NULL'
[   26.231892] Initializing USB Mass Storage driver...
[   26.231968] usbcore: registered new interface driver usb-storage
[   26.231970] USB Mass Storage support registered.
[   26.238432] tg3.c:v3.108 (February 17, 2010)
[   26.238458]   alloc irq_desc for 22 on node -1
[   26.238460]   alloc kstat_irqs on node -1
[   26.238469] tg3 0000:06:05.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[   26.257099] Bluetooth: Core ver 2.15
[   26.296073] intel_rng: FWH not detected
[   26.311644] ACPI: Lid Switch [LID0]
[   26.312464] ACPI: AC Adapter [ADP1] (on-line)
[   26.315853] iTCO_vendor_support: vendor-support=0
[   26.353077] ACPI: Battery Slot [BAT1] (battery present)
[   26.353228] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input4
[   26.353279] ACPI: Power Button [PWRB]
[   26.353322] input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input5
[   26.353346] ACPI: Sleep Button [SLPB]
[   26.353396] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input6
[   26.353420] ACPI: Power Button [PWRF]
[   26.438006] tg3 0000:06:05.0: eth0: Tigon3 [partno(BCM95788A50) rev 3003] (PCI:33MHz:32-bit) MAC address 00:13:77:01:ab:92
[   26.438012] tg3 0000:06:05.0: eth0: attached PHY is 5705 (10/100/1000Base-T Ethernet) (WireSpeed[0])
[   26.438015] tg3 0000:06:05.0: eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] TSOcap[1]
[   26.438018] tg3 0000:06:05.0: eth0: dma_rwctrl[763f0000] dma_mask[32-bit]
[   26.467970] NET: Registered protocol family 31
[   26.467973] Bluetooth: HCI device and connection manager initialized
[   26.467976] Bluetooth: HCI socket layer initialized
[   26.469978] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.05
[   26.470062] iTCO_wdt: Found a ICH6-M TCO device (Version=2, TCOBASE=0x1060)
[   26.470111] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[   26.473765] sd 0:0:0:0: Attached scsi generic sg0 type 0
[   26.473792] scsi 1:0:0:0: Attached scsi generic sg1 type 5
[   26.494602] cfg80211: Calling CRDA to update world regulatory domain
[   26.587227] Bluetooth: Generic Bluetooth USB driver ver 0.6
[   26.587332] usbcore: registered new interface driver btusb
[   26.600499] cfg80211: World regulatory domain updated:
[   26.600502]     (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   26.600505]     (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   26.600508]     (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   26.600511]     (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   26.600513]     (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   26.600516]     (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   26.605470] ieee80211: 802.11 data/management/control stack, git-1.1.13
[   26.605473] ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com>
[   26.618689] ipw2200: Intel(R) PRO/Wireless 2200/2915 Network Driver, 1.2.2kdmprq
[   26.618693] ipw2200: Copyright(c) 2003-2006 Intel Corporation
[   26.618789] ipw2200 0000:06:07.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
[   26.619354] ipw2200: Detected Intel PRO/Wireless 2915ABG Network Connection
[   26.619405] ipw2200 0000:06:07.0: firmware: requesting ipw2200-bss.fw
[   26.761877] tpm_inf_pnp 00:08: Found TPM with ID IFX0101
[   26.761928] tpm_inf_pnp 00:08: TPM found: config base 0x4e, data base 0x6e0, chip version 0x0006, vendor id 0x15d1 (Infineon), product id 0x0006 (SLD 9630 TT 1.1)
[   26.765960] Intel ICH Modem 0000:00:1e.3: PCI INT B -> GSI 20 (level, low) -> IRQ 20
[   26.765978] Intel ICH Modem 0000:00:1e.3: setting latency timer to 64
[   26.778545] sdhci: Secure Digital Host Controller Interface driver
[   26.778548] sdhci: Copyright(c) Pierre Ossman
[   26.787355] scsi2 : usb-storage 1-2:1.0
[   26.799272] Intel ICH 0000:00:1e.2: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[   26.799315] Intel ICH 0000:00:1e.2: setting latency timer to 64
[   26.801546] usbcore: registered new interface driver ums-cypress
[   26.808321] sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
[   26.808326] Uniform CD-ROM driver Revision: 3.20
[   26.808441] sr 1:0:0:0: Attached scsi CD-ROM sr0
[   26.854944] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/device:00/LNXVIDEO:00/input/input7
[   26.855003] ACPI: Video Device [ATIM] (multi-head: yes  rom: no  post: no)
[   26.869304] ipw2200: Detected geography ZZE (13 802.11bg channels, 19 802.11a channels)
[   26.869502] ohci1394 0000:06:09.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[   26.926083] ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[17]  MMIO=[c8011000-c80117ff]  Max Packet=[2048]  IR/IT contexts=[4/4]
[   26.940176] yenta_cardbus 0000:06:09.0: CardBus bridge found [144d:c018]
[   27.068793] yenta_cardbus 0000:06:09.0: ISA IRQ mask 0x0cb8, PCI irq 16
[   27.068798] yenta_cardbus 0000:06:09.0: Socket status: 30000006
[   27.068802] pci_bus 0000:06: Raising subordinate bus# of parent bus (#06) from #06 to #0a
[   27.068811] yenta_cardbus 0000:06:09.0: pcmcia: parent PCI bridge window: [io  0x5000-0x5fff]
[   27.068814] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x5000-0x5fff: excluding 0x5000-0x50ff 0x5400-0x54ff
[   27.074430] yenta_cardbus 0000:06:09.0: pcmcia: parent PCI bridge window: [mem 0xc8000000-0xc80fffff]
[   27.074433] pcmcia_socket pcmcia_socket0: cs: memory probe 0xc8000000-0xc80fffff: excluding 0xc8000000-0xc801ffff
[   27.074445] yenta_cardbus 0000:06:09.0: pcmcia: parent PCI bridge window: [mem 0x80000000-0x83ffffff pref]
[   27.074448] pcmcia_socket pcmcia_socket0: cs: memory probe 0x80000000-0x83ffffff: excluding 0x80000000-0x83ffffff
[   27.074830] sdhci-pci 0000:06:09.2: SDHCI controller found [1180:0822] (rev 17)
[   27.074854] sdhci-pci 0000:06:09.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[   27.074914] sdhci-pci 0000:06:09.2: Will use DMA mode even though HW doesn't fully claim to support it.
[   27.074943] Registered led device: mmc0::
[   27.074974] mmc0: SDHCI controller on PCI [0000:06:09.2] using DMA
[   27.087467] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x100-0x3af: excluding 0x170-0x177 0x1f0-0x1f7 0x370-0x377
[   27.089479] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x3e0-0x4ff: excluding 0x3f0-0x3f7 0x4d0-0x4d7
[   27.090217] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x820-0x8ff: clean.
[   27.090827] pcmcia_socket pcmcia_socket0: cs: IO port probe 0xc00-0xcf7: clean.
[   27.091501] pcmcia_socket pcmcia_socket0: cs: memory probe 0x0c0000-0x0fffff: excluding 0xc0000-0xd3fff 0xdc000-0xfffff
[   27.091557] pcmcia_socket pcmcia_socket0: cs: memory probe 0xa0000000-0xa0ffffff: clean.
[   27.091611] pcmcia_socket pcmcia_socket0: cs: memory probe 0x60000000-0x60ffffff: excluding 0x60000000-0x60ffffff
[   27.091668] pcmcia_socket pcmcia_socket0: cs: IO port probe 0xa00-0xaff: clean.
[   27.724041] intel8x0_measure_ac97_clock: measured 55473 usecs (2673 samples)
[   27.724044] intel8x0: clocking to 48000
[   27.802456] scsi 2:0:0:0: Direct-Access     FUJITSU  MHV2080AT        0000 PQ: 0 ANSI: 0
[   27.802613] sd 2:0:0:0: Attached scsi generic sg2 type 0
[   27.806058] sd 2:0:0:0: [sdb] 156301488 512-byte logical blocks: (80.0 GB/74.5 GiB)
[   27.806930] sd 2:0:0:0: [sdb] Write Protect is off
[   27.806933] sd 2:0:0:0: [sdb] Mode Sense: 27 00 00 00
[   27.806935] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[   27.808429] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[   27.808437]  sdb: sdb1 sdb2 sdb3
[   28.172678] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[   28.172689] sd 2:0:0:0: [sdb] Attached SCSI disk
[   28.212127] ieee1394: Host added: ID:BUS[0-00:1023]  GUID[0000f04120050c8c]
[   29.000974] Adding 2031188k swap on /dev/mapper/cr_sda10.  Priority:-1 extents:1 across:2031188k 
[   30.399027] loop: module loaded
[   31.788430] BIOS EDD facility v0.16 2004-Jun-25, 1 devices found
[   31.951426] bootsplash: status on console 0 changed to on
[   43.682360] bootsplash: status on console 0 changed to on
[   48.482755] kjournald starting.  Commit interval 15 seconds
[   48.483181] EXT3-fs (sda6): using internal journal
[   48.483186] EXT3-fs (sda6): mounted filesystem with ordered data mode
[   48.527333] kjournald starting.  Commit interval 15 seconds
[   48.527339] EXT3-fs (dm-8): warning: maximal mount count reached, running e2fsck is recommended
[   48.527890] EXT3-fs (dm-8): using internal journal
[   48.527894] EXT3-fs (dm-8): mounted filesystem with ordered data mode
[   48.560843] kjournald starting.  Commit interval 15 seconds
[   48.560848] EXT3-fs (dm-5): mounted filesystem with ordered data mode
[   48.576657] kjournald starting.  Commit interval 15 seconds
[   48.577086] EXT3-fs (dm-2): using internal journal
[   48.577089] EXT3-fs (dm-2): mounted filesystem with ordered data mode
[   48.590188] kjournald starting.  Commit interval 15 seconds
[   48.590591] EXT3-fs (dm-1): using internal journal
[   48.590594] EXT3-fs (dm-1): mounted filesystem with ordered data mode
[   48.598525] fuse init (API version 7.13)
[   50.201250] type=1505 audit(1290549069.200:2): operation="profile_load" pid=1653 name=/bin/ping
[   50.262519] type=1505 audit(1290549069.260:3): operation="profile_load" pid=1654 name=/sbin/klogd
[   50.445114] type=1505 audit(1290549069.444:4): operation="profile_load" pid=1655 name=/sbin/syslog-ng
[   50.579602] type=1505 audit(1290549069.576:5): operation="profile_load" pid=1681 name=/sbin/syslogd
[   50.698001] type=1505 audit(1290549069.696:6): operation="profile_load" pid=1686 name=/usr/sbin/avahi-daemon
[   50.806671] type=1505 audit(1290549069.804:7): operation="profile_load" pid=1687 name=/usr/sbin/identd
[   50.934842] type=1505 audit(1290549069.932:8): operation="profile_load" pid=1688 name=/usr/sbin/mdnsd
[   51.068171] type=1505 audit(1290549070.068:9): operation="profile_load" pid=1699 name=/usr/sbin/nscd
[   51.260566] type=1505 audit(1290549070.260:10): operation="profile_load" pid=1700 name=/usr/sbin/ntpd
[   51.358668] type=1505 audit(1290549070.356:11): operation="profile_load" pid=1701 name=/usr/sbin/traceroute
[   51.711051] powernow: This module only works with AMD K7 CPUs
[   51.752820] processor_perflib-0349 [00] processor_get_performa: Found 6 performance states
[   51.752826] processor_perflib-0367 [00] processor_get_performa: Extracting state 0
[   51.752830] processor_perflib-0385 [00] processor_get_performa: State [0]: core_frequency[2133] power[27000] transition_latency[10] bus_master_latency[10] control[0x1029] status[0x1029]
[   51.752837] processor_perflib-0367 [00] processor_get_performa: Extracting state 1
[   51.752841] processor_perflib-0385 [00] processor_get_performa: State [1]: core_frequency[1867] power[24000] transition_latency[10] bus_master_latency[10] control[0xe25] status[0xe25]
[   51.752847] processor_perflib-0367 [00] processor_get_performa: Extracting state 2
[   51.752851] processor_perflib-0385 [00] processor_get_performa: State [2]: core_frequency[1600] power[21000] transition_latency[10] bus_master_latency[10] control[0xc20] status[0xc20]
[   51.752857] processor_perflib-0367 [00] processor_get_performa: Extracting state 3
[   51.752861] processor_perflib-0385 [00] processor_get_performa: State [3]: core_frequency[1333] power[19000] transition_latency[10] bus_master_latency[10] control[0xa1c] status[0xa1c]
[   51.752867] processor_perflib-0367 [00] processor_get_performa: Extracting state 4
[   51.752871] processor_perflib-0385 [00] processor_get_performa: State [4]: core_frequency[1067] power[16000] transition_latency[10] bus_master_latency[10] control[0x817] status[0x817]
[   51.752877] processor_perflib-0367 [00] processor_get_performa: Extracting state 5
[   51.752881] processor_perflib-0385 [00] processor_get_performa: State [5]: core_frequency[800] power[13000] transition_latency[10] bus_master_latency[10] control[0x612] status[0x612]
[   51.752940] processor_perflib-0486 [00] processor_notify_smm  : No SMI port or pstate_control
[   51.799849] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   51.984643] ip_tables: (C) 2000-2006 Netfilter Core Team
[   52.004758] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[   54.423859] Bluetooth: L2CAP ver 2.14
[   54.423863] Bluetooth: L2CAP socket layer initialized
[   54.518839] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[   54.518842] Bluetooth: BNEP filters: protocol multicast
[   54.589038] Bridge firewalling registered
[   54.709379] Bluetooth: SCO (Voice Link) ver 0.6
[   54.709382] Bluetooth: SCO socket layer initialized
[   54.936492] tg3 0000:06:05.0: firmware: requesting tigon/tg3_tso5.bin
[   55.224448] Bluetooth: RFCOMM TTY layer initialized
[   55.224454] Bluetooth: RFCOMM socket layer initialized
[   55.224456] Bluetooth: RFCOMM ver 1.11
[   55.470735] ADDRCONF(NETDEV_UP): eth0: link is not ready
[   55.744244] NET: Registered protocol family 17
[   58.324873] tg3 0000:06:05.0: eth0: Link is up at 1000 Mbps, full duplex
[   58.324882] tg3 0000:06:05.0: eth0: Flow control is on for TX and on for RX
[   58.325332] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   63.992168] bootsplash: status on console 0 changed to on
[   66.086989] CPUFREQ: Per core ondemand sysfs interface is deprecated - up_threshold
[   96.556512] kjournald starting.  Commit interval 15 seconds
[   96.556537] EXT3-fs (sdb3): warning: maximal mount count reached, running e2fsck is recommended
[   96.557232] EXT3-fs (sdb3): using internal journal
[   96.557321] EXT3-fs (sdb3): mounted filesystem with ordered data mode
[  192.080979] show_signal_msg: 3 callbacks suppressed
[  192.080990] npviewer.bin[3758]: segfault at 0 ip (null) sp bfcf274c error 4 in npviewer.bin[8048000+2a000]
[  192.416445] npviewer.bin[3769]: segfault at 0 ip (null) sp bffec35c error 4 in npviewer.bin[8048000+2a000]
[  192.767261] npviewer.bin[3779]: segfault at 0 ip (null) sp bfc6c65c error 4 in npviewer.bin[8048000+2a000]
[  193.180127] npviewer.bin[3789]: segfault at 0 ip (null) sp bfb642dc error 4 in npviewer.bin[8048000+2a000]
[ 4606.597434] SFW2-OUT-ERROR IN= OUT=eth0 SRC=192.168.1.33 DST=195.4.92.212 LEN=52 TOS=0x00 PREC=0x00 TTL=64 ID=12063 DF PROTO=TCP SPT=49606 DPT=993 WINDOW=182 RES=0x00 ACK FIN URGP=0 OPT (0101080A00106DA9331FA4C5) 
[ 4606.820060] SFW2-OUT-ERROR IN= OUT=eth0 SRC=192.168.1.33 DST=195.4.92.212 LEN=52 TOS=0x00 PREC=0x00 TTL=64 ID=12064 DF PROTO=TCP SPT=49606 DPT=993 WINDOW=182 RES=0x00 ACK FIN URGP=0 OPT (0101080A00106DE1331FA4C5) 
[ 4607.268086] SFW2-OUT-ERROR IN= OUT=eth0 SRC=192.168.1.33 DST=195.4.92.212 LEN=52 TOS=0x00 PREC=0x00 TTL=64 ID=12065 DF PROTO=TCP SPT=49606 DPT=993 WINDOW=182 RES=0x00 ACK FIN URGP=0 OPT (0101080A00106E51331FA4C5) 
[ 4608.164094] SFW2-OUT-ERROR IN= OUT=eth0 SRC=192.168.1.33 DST=195.4.92.212 LEN=52 TOS=0x00 PREC=0x00 TTL=64 ID=12066 DF PROTO=TCP SPT=49606 DPT=993 WINDOW=182 RES=0x00 ACK FIN URGP=0 OPT (0101080A00106F31331FA4C5) 
[ 4609.956056] SFW2-OUT-ERROR IN= OUT=eth0 SRC=192.168.1.33 DST=195.4.92.212 LEN=52 TOS=0x00 PREC=0x00 TTL=64 ID=12067 DF PROTO=TCP SPT=49606 DPT=993 WINDOW=182 RES=0x00 ACK FIN URGP=0 OPT (0101080A001070F1331FA4C5) 
[ 4635.044067] SFW2-OUT-ERROR IN= OUT=eth0 SRC=192.168.1.33 DST=195.4.92.212 LEN=52 TOS=0x00 PREC=0x00 TTL=64 ID=12070 DF PROTO=TCP SPT=49606 DPT=993 WINDOW=182 RES=0x00 ACK FIN URGP=0 OPT (0101080A00108971331FA4C5) 
[ 4663.716061] SFW2-OUT-ERROR IN= OUT=eth0 SRC=192.168.1.33 DST=195.4.92.212 LEN=52 TOS=0x00 PREC=0x00 TTL=64 ID=12071 DF PROTO=TCP SPT=49606 DPT=993 WINDOW=182 RES=0x00 ACK FIN URGP=0 OPT (0101080A0010A571331FA4C5) 

[-- Attachment #3: Type: text/plain, Size: 138 bytes --]

_______________________________________________
Xen-devel mailing list
Xen-devel@lists.xensource.com
http://lists.xensource.com/xen-devel