From: trimarchi@gandalf.sssup.it (Michael Trimarchi)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH 28/51] ARM: mx25: dynamically allocate mxc-ehci devices
Date: Fri, 26 Nov 2010 16:24:41 +0100 [thread overview]
Message-ID: <4CEFD139.8090600@gandalf.sssup.it> (raw)
In-Reply-To: <4CEFCC9A.2020500@fqingenieria.es>
Hi
On 11/26/2010 04:04 PM, Jaume Ribot wrote:
> Dear Uwe,
>
> I think there is an error in the Freescale documentation, as new 0x200 offset (as it might be according reference manual) makes usbh2 stops working.
>
> Other users have experienced simmilar issues:
> http://forums.freescale.com/t5/i-MX-Microprocessors/i-MX25-USBOH-host-core-port-on-chip-serial-PHY-Control/m-p/59365
>
> I think old 0x400 offset value were correct.
> Anyone can confirm?
I can say that I'm using the mainline (814ce2521121c2459e16cea8c7221e157edbeddd) without this patch and the usbhost work
on my mx25 board.
These are my settings:
static struct mxc_usbh_platform_data usbh2_pdata = {
.portsc = MXC_EHCI_MODE_SERIAL,
.flags = MXC_EHCI_INTERFACE_DIFF_UNI | MXC_EHCI_INTERNAL_PHY |
MXC_EHCI_PP_HST | MXC_EHCI_XCSH |
MXC_EHCI_IPPUE_DOWN | MXC_EHCI_POWER_PINS_ENABLED,
};
/* USB */
MX25_PAD_PWM__USBH2_OC,
MX25_PAD_CONTRAST__USBH2_PWR,
I have done some test with an usb pendrive
Michael
>
> On 17/11/2010 22:29, Uwe Kleine-K?nig wrote:
>> According to the reference manual of the i.MX25 the host controller uses an
>> offset of 0x200 not 0x400 as was specified in the resources for mxc_usbh2.
>>
>> Needs-Testing: yes
>> Signed-off-by: Uwe Kleine-K?nig<u.kleine-koenig@pengutronix.de>
>> ---
>> arch/arm/mach-mx25/Kconfig | 6 ++-
>> arch/arm/mach-mx25/devices-imx25.h | 7 ++++
>> arch/arm/mach-mx25/devices.c | 44 ++----------------------
>> arch/arm/mach-mx25/devices.h | 2 -
>> arch/arm/mach-mx25/mach-cpuimx25.c | 9 ++---
>> arch/arm/mach-mx25/mach-mx25_3ds.c | 2 +-
>> arch/arm/plat-mxc/devices/platform-mxc-ehci.c | 7 ++++
>> arch/arm/plat-mxc/ehci.c | 4 +-
>> arch/arm/plat-mxc/include/mach/mx25.h | 6 +++-
>> 9 files changed, 34 insertions(+), 53 deletions(-)
>>
>> diff --git a/arch/arm/mach-mx25/Kconfig b/arch/arm/mach-mx25/Kconfig
>> index 38ca09a..b55585b 100644
>> --- a/arch/arm/mach-mx25/Kconfig
>> +++ b/arch/arm/mach-mx25/Kconfig
>> @@ -5,16 +5,18 @@ comment "MX25 platforms:"
>> config MACH_MX25_3DS
>> bool "Support MX25PDK (3DS) Platform"
>> select IMX_HAVE_PLATFORM_IMX_UART
>> + select IMX_HAVE_PLATFORM_MXC_EHCI
>> select IMX_HAVE_PLATFORM_MXC_NAND
>> select IMX_HAVE_PLATFORM_ESDHC
>>
>> config MACH_EUKREA_CPUIMX25
>> bool "Support Eukrea CPUIMX25 Platform"
>> + select IMX_HAVE_PLATFORM_ESDHC
>> + select IMX_HAVE_PLATFORM_FLEXCAN
>> select IMX_HAVE_PLATFORM_IMX_I2C
>> select IMX_HAVE_PLATFORM_IMX_UART
>> + select IMX_HAVE_PLATFORM_MXC_EHCI
>> select IMX_HAVE_PLATFORM_MXC_NAND
>> - select IMX_HAVE_PLATFORM_FLEXCAN
>> - select IMX_HAVE_PLATFORM_ESDHC
>> select MXC_ULPI if USB_ULPI
>>
>> choice
>> diff --git a/arch/arm/mach-mx25/devices-imx25.h b/arch/arm/mach-mx25/devices-imx25.h
>> index f62ce93..ac343ae 100644
>> --- a/arch/arm/mach-mx25/devices-imx25.h
>> +++ b/arch/arm/mach-mx25/devices-imx25.h
>> @@ -39,6 +39,13 @@ extern const struct imx_imx_uart_1irq_data imx25_imx_uart_data[] __initconst;
>> #define imx25_add_imx_uart3(pdata) imx25_add_imx_uart(3, pdata)
>> #define imx25_add_imx_uart4(pdata) imx25_add_imx_uart(4, pdata)
>>
>> +extern const struct imx_mxc_ehci_data imx25_mxc_ehci_otg_data __initconst;
>> +#define imx25_add_mxc_ehci_otg(pdata) \
>> + imx_add_mxc_ehci(&imx25_mxc_ehci_otg_data, pdata)
>> +extern const struct imx_mxc_ehci_data imx25_mxc_ehci_hs_data __initconst;
>> +#define imx25_add_mxc_ehci_hs(pdata) \
>> + imx_add_mxc_ehci(&imx25_mxc_ehci_hs_data, pdata)
>> +
>> extern const struct imx_mxc_nand_data imx25_mxc_nand_data __initconst;
>> #define imx25_add_mxc_nand(pdata) \
>> imx_add_mxc_nand(&imx25_mxc_nand_data, pdata)
>> diff --git a/arch/arm/mach-mx25/devices.c b/arch/arm/mach-mx25/devices.c
>> index 92eb1a9..4611c76 100644
>> --- a/arch/arm/mach-mx25/devices.c
>> +++ b/arch/arm/mach-mx25/devices.c
>> @@ -26,27 +26,16 @@ static u64 otg_dmamask = DMA_BIT_MASK(32);
>>
>> static struct resource mxc_otg_resources[] = {
>> {
>> - .start = MX25_OTG_BASE_ADDR,
>> - .end = MX25_OTG_BASE_ADDR + 0x1ff,
>> + .start = MX25_USB_OTG_BASE_ADDR,
>> + .end = MX25_USB_OTG_BASE_ADDR + 0x1ff,
>> .flags = IORESOURCE_MEM,
>> }, {
>> - .start = 37,
>> - .end = 37,
>> + .start = MX25_INT_USB_OTG,
>> + .end = MX25_INT_USB_OTG,
>> .flags = IORESOURCE_IRQ,
>> },
>> };
>>
>> -struct platform_device mxc_otg = {
>> - .name = "mxc-ehci",
>> - .id = 0,
>> - .dev = {
>> - .coherent_dma_mask = 0xffffffff,
>> - .dma_mask =&otg_dmamask,
>> - },
>> - .resource = mxc_otg_resources,
>> - .num_resources = ARRAY_SIZE(mxc_otg_resources),
>> -};
>> -
>> /* OTG gadget device */
>> struct platform_device otg_udc_device = {
>> .name = "fsl-usb2-udc",
>> @@ -59,31 +48,6 @@ struct platform_device otg_udc_device = {
>> .num_resources = ARRAY_SIZE(mxc_otg_resources),
>> };
>>
>> -static u64 usbh2_dmamask = DMA_BIT_MASK(32);
>> -
>> -static struct resource mxc_usbh2_resources[] = {
>> - {
>> - .start = MX25_OTG_BASE_ADDR + 0x400,
>> - .end = MX25_OTG_BASE_ADDR + 0x5ff,
>> - .flags = IORESOURCE_MEM,
>> - }, {
>> - .start = 35,
>> - .end = 35,
>> - .flags = IORESOURCE_IRQ,
>> - },
>> -};
>> -
>> -struct platform_device mxc_usbh2 = {
>> - .name = "mxc-ehci",
>> - .id = 1,
>> - .dev = {
>> - .coherent_dma_mask = 0xffffffff,
>> - .dma_mask =&usbh2_dmamask,
>> - },
>> - .resource = mxc_usbh2_resources,
>> - .num_resources = ARRAY_SIZE(mxc_usbh2_resources),
>> -};
>> -
>> static struct resource mxc_pwm_resources0[] = {
>> {
>> .start = 0x53fe0000,
>> diff --git a/arch/arm/mach-mx25/devices.h b/arch/arm/mach-mx25/devices.h
>> index 7b70a43..e6ad640 100644
>> --- a/arch/arm/mach-mx25/devices.h
>> +++ b/arch/arm/mach-mx25/devices.h
>> @@ -1,6 +1,4 @@
>> -extern struct platform_device mxc_otg;
>> extern struct platform_device otg_udc_device;
>> -extern struct platform_device mxc_usbh2;
>> extern struct platform_device mxc_pwm_device0;
>> extern struct platform_device mxc_pwm_device1;
>> extern struct platform_device mxc_pwm_device2;
>> diff --git a/arch/arm/mach-mx25/mach-cpuimx25.c b/arch/arm/mach-mx25/mach-cpuimx25.c
>> index f6f9ad6..0ee0fe7 100644
>> --- a/arch/arm/mach-mx25/mach-cpuimx25.c
>> +++ b/arch/arm/mach-mx25/mach-cpuimx25.c
>> @@ -39,7 +39,6 @@
>> #include<mach/mx25.h>
>> #include<mach/mxc_nand.h>
>> #include<mach/imxfb.h>
>> -#include<mach/mxc_ehci.h>
>> #include<mach/iomux-mx25.h>
>>
>> #include "devices-imx25.h"
>> @@ -87,12 +86,12 @@ static struct i2c_board_info eukrea_cpuimx25_i2c_devices[] = {
>> },
>> };
>>
>> -static struct mxc_usbh_platform_data otg_pdata = {
>> +static const struct mxc_usbh_platform_data otg_pdata __initconst = {
>> .portsc = MXC_EHCI_MODE_UTMI,
>> .flags = MXC_EHCI_INTERFACE_DIFF_UNI,
>> };
>>
>> -static struct mxc_usbh_platform_data usbh2_pdata = {
>> +static const struct mxc_usbh_platform_data usbh2_pdata __initconst = {
>> .portsc = MXC_EHCI_MODE_SERIAL,
>> .flags = MXC_EHCI_INTERFACE_SINGLE_UNI | MXC_EHCI_INTERNAL_PHY |
>> MXC_EHCI_IPPUE_DOWN,
>> @@ -134,11 +133,11 @@ static void __init eukrea_cpuimx25_init(void)
>> imx25_add_imx_i2c0(&eukrea_cpuimx25_i2c0_data);
>>
>> if (otg_mode_host)
>> - mxc_register_device(&mxc_otg,&otg_pdata);
>> + imx25_add_mxc_ehci_otg(&otg_pdata);
>> else
>> mxc_register_device(&otg_udc_device,&otg_device_pdata);
>>
>> - mxc_register_device(&mxc_usbh2,&usbh2_pdata);
>> + imx25_add_mxc_ehci_hs(&usbh2_pdata);
>>
>> #ifdef CONFIG_MACH_EUKREA_MBIMXSD25_BASEBOARD
>> eukrea_mbimxsd25_baseboard_init();
>> diff --git a/arch/arm/mach-mx25/mach-mx25_3ds.c b/arch/arm/mach-mx25/mach-mx25_3ds.c
>> index f8be1eb..574c41f 100644
>> --- a/arch/arm/mach-mx25/mach-mx25_3ds.c
>> +++ b/arch/arm/mach-mx25/mach-mx25_3ds.c
>> @@ -192,7 +192,7 @@ static void __init mx25pdk_init(void)
>> ARRAY_SIZE(mx25pdk_pads));
>>
>> imx25_add_imx_uart0(&uart_pdata);
>> - mxc_register_device(&mxc_usbh2, NULL);
>> + imx25_add_mxc_ehci_hs(NULL);
>> imx25_add_mxc_nand(&mx25pdk_nand_board_info);
>> mxc_register_device(&mx25_rtc_device, NULL);
>> mxc_register_device(&mx25_fb_device,&mx25pdk_fb_pdata);
>> diff --git a/arch/arm/plat-mxc/devices/platform-mxc-ehci.c b/arch/arm/plat-mxc/devices/platform-mxc-ehci.c
>> index 0cb67bb..825a048ca 100644
>> --- a/arch/arm/plat-mxc/devices/platform-mxc-ehci.c
>> +++ b/arch/arm/plat-mxc/devices/platform-mxc-ehci.c
>> @@ -16,6 +16,13 @@
>> .irq = soc ## _INT_USB_ ## hs, \
>> }
>>
>> +#ifdef CONFIG_ARCH_MX25
>> +const struct imx_mxc_ehci_data imx25_mxc_ehci_otg_data __initconst =
>> + imx_mxc_ehci_data_entry_single(MX25, 0, OTG);
>> +const struct imx_mxc_ehci_data imx25_mxc_ehci_hs_data __initconst =
>> + imx_mxc_ehci_data_entry_single(MX25, 1, HS);
>> +#endif /* ifdef CONFIG_ARCH_MX25 */
>> +
>> #ifdef CONFIG_SOC_IMX27
>> const struct imx_mxc_ehci_data imx27_mxc_ehci_otg_data __initconst =
>> imx_mxc_ehci_data_entry_single(MX27, 0, OTG);
>> diff --git a/arch/arm/plat-mxc/ehci.c b/arch/arm/plat-mxc/ehci.c
>> index 9915607..f699235 100644
>> --- a/arch/arm/plat-mxc/ehci.c
>> +++ b/arch/arm/plat-mxc/ehci.c
>> @@ -71,7 +71,7 @@ int mxc_initialize_usb_hw(int port, unsigned int flags)
>> unsigned int v;
>> #if defined(CONFIG_ARCH_MX25)
>> if (cpu_is_mx25()) {
>> - v = readl(MX25_IO_ADDRESS(MX25_OTG_BASE_ADDR +
>> + v = readl(MX25_IO_ADDRESS(MX25_USB_BASE_ADDR +
>> USBCTRL_OTGBASE_OFFSET));
>>
>> switch (port) {
>> @@ -108,7 +108,7 @@ int mxc_initialize_usb_hw(int port, unsigned int flags)
>> return -EINVAL;
>> }
>>
>> - writel(v, MX25_IO_ADDRESS(MX25_OTG_BASE_ADDR +
>> + writel(v, MX25_IO_ADDRESS(MX25_USB_BASE_ADDR +
>> USBCTRL_OTGBASE_OFFSET));
>> return 0;
>> }
>> diff --git a/arch/arm/plat-mxc/include/mach/mx25.h b/arch/arm/plat-mxc/include/mach/mx25.h
>> index a2404b0..0d31f82 100644
>> --- a/arch/arm/plat-mxc/include/mach/mx25.h
>> +++ b/arch/arm/plat-mxc/include/mach/mx25.h
>> @@ -43,7 +43,9 @@
>> #define MX25_LCDC_BASE_ADDR 0x53fbc000
>> #define MX25_KPP_BASE_ADDR 0x43fa8000
>> #define MX25_SDMA_BASE_ADDR 0x53fd4000
>> -#define MX25_OTG_BASE_ADDR 0x53ff4000
>> +#define MX25_USB_BASE_ADDR 0x53ff4000
>> +#define MX25_USB_OTG_BASE_ADDR (MX25_USB_BASE_ADDR + 0x0000)
>> +#define MX25_USB_HS_BASE_ADDR (MX25_USB_BASE_ADDR + 0x0200)
>> #define MX25_CSI_BASE_ADDR 0x53ff8000
>>
>> #define MX25_IO_P2V(x) IMX_IO_P2V(x)
>> @@ -67,6 +69,8 @@
>> #define MX25_INT_UART2 32
>> #define MX25_INT_NFC 33
>> #define MX25_INT_SDMA 34
>> +#define MX25_INT_USB_HS 35
>> +#define MX25_INT_USB_OTG 37
>> #define MX25_INT_LCDC 39
>> #define MX25_INT_UART5 40
>> #define MX25_INT_CAN1 43
>
>
-------------- next part --------------
A non-text attachment was scrubbed...
Name: mx25_usbh2.patch
Type: text/x-patch
Size: 3001 bytes
Desc: not available
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20101126/a1cd8200/attachment-0001.bin>
next prev parent reply other threads:[~2010-11-26 15:24 UTC|newest]
Thread overview: 78+ messages / expand[flat|nested] mbox.gz Atom feed top
2010-11-17 21:28 [PATCH 00/51] some more imx patches for 2.6.38 Uwe Kleine-König
2010-11-17 21:29 ` [PATCH 01/51] ARM: mx3: fix the last users of IMX_NEEDS_DEPRECATED_SYMBOLS Uwe Kleine-König
2010-11-17 21:29 ` [PATCH 02/51] ARM: imx: refactor the io mapping macro Uwe Kleine-König
2010-11-17 21:29 ` [PATCH 03/51] ARM: imx: use MXxy_IO_P2V macros to setup static mappings Uwe Kleine-König
2010-11-17 21:29 ` [PATCH 04/51] ARM: imx: remove last explicit users of virtual base address defines Uwe Kleine-König
2010-11-17 21:29 ` [PATCH 05/51] ARM: imx: change static io mapping to use a function Uwe Kleine-König
2010-11-17 21:29 ` [PATCH 06/51] ARM: imx/debug-macro: rework using the new io mapping macro Uwe Kleine-König
2010-11-17 21:29 ` [PATCH 07/51] ARM: imx: remove deprecated symbols as all users are gone now Uwe Kleine-König
2010-11-17 21:29 ` [PATCH 08/51] ARM: imx: dynamically allocate mxc_w1 devices Uwe Kleine-König
2010-11-17 21:29 ` [PATCH 09/51] ARM: imx: remove unused devices Uwe Kleine-König
2010-11-17 21:29 ` [PATCH 10/51] ARM: imx: dynamically allocate imx_udc device Uwe Kleine-König
2010-11-17 21:29 ` [PATCH 11/51] ARM: imx: allow specifying a dma mask when creating a platform device Uwe Kleine-König
2010-11-17 21:29 ` [PATCH 12/51] ARM: imx: dynamically allocate mx1-camera device Uwe Kleine-König
2010-11-17 21:29 ` [PATCH 13/51] ARM: imx/gpio: remove some useless casts Uwe Kleine-König
2010-11-17 21:29 ` [PATCH 14/51] ARM: imx: dynamically allocate mx2-camera device Uwe Kleine-König
2010-11-17 21:29 ` [PATCH 15/51] ARM: imx: dynamically allocate imx2-wdt devices Uwe Kleine-König
2010-11-17 21:29 ` [PATCH 16/51] ARM: imx: change the way flexcan devices are registered Uwe Kleine-König
2010-11-17 21:29 ` [PATCH 17/51] ARM: imx: dynamically register imx-fb devices Uwe Kleine-König
2010-11-17 21:29 ` [PATCH 18/51] ARM: mx3: enable SPI_IMX for better compile coverage Uwe Kleine-König
2010-11-17 21:29 ` [PATCH 19/51] ARM: imx: dynamically allocate mxc_pwm devices Uwe Kleine-König
2010-11-17 21:29 ` [PATCH 20/51] ARM: mx3/mach-pcm037_eet: Fix section mismatch for eet_init_devices() Uwe Kleine-König
2010-11-17 21:29 ` [PATCH 21/51] ARM: imx: dynamically register mxc-mmc devices Uwe Kleine-König
2010-11-17 21:29 ` [PATCH 22/51] ARM: imx: dynamically allocate mxc-ehci devices Uwe Kleine-König
2010-11-17 21:29 ` [PATCH 23/51] ARM: imx: dynamically allocate fsl-usb2-udc devices Uwe Kleine-König
2010-11-17 21:29 ` [PATCH 24/51] ARM: imx: dynamically allocate imx-keypad devices Uwe Kleine-König
2010-11-17 21:29 ` [PATCH 25/51] ARM: imx: dynamically allocate imx21-hcd devices Uwe Kleine-König
2010-11-17 21:29 ` [PATCH 26/51] ARM: imx: remove now empty devices.h Uwe Kleine-König
2010-11-17 21:29 ` [PATCH 27/51] ARM: imx: move registration of gpios to plat-mxc/gpio.c Uwe Kleine-König
2010-11-17 21:29 ` [PATCH 28/51] ARM: mx25: dynamically allocate mxc-ehci devices Uwe Kleine-König
2010-11-26 15:04 ` Jaume Ribot
2010-11-26 15:24 ` Michael Trimarchi [this message]
2010-11-26 20:07 ` Uwe Kleine-König
[not found] ` <4CF38BE9.1030607@gandalf.sssup.it>
[not found] ` <20101129113846.GD20449@pengutronix.de>
2010-12-02 11:00 ` [RFC PATCH] mxc_timer1 patch on imx25 Michael Trimarchi
2010-12-02 11:32 ` Baruch Siach
2010-12-02 12:41 ` Michael Trimarchi
2010-11-26 19:48 ` [PATCH 28/51] ARM: mx25: dynamically allocate mxc-ehci devices Uwe Kleine-König
2010-11-29 2:48 ` Shawn Guo
2010-11-29 7:40 ` jaume at fqingenieria.es
2010-11-29 7:58 ` [PATCH] ARM: mx25: fix offset for usb host controller Uwe Kleine-König
2010-11-29 14:51 ` [PATCH 28/51] ARM: mx25: dynamically allocate mxc-ehci devices Robert Schwebel
2010-11-29 19:35 ` Robert Schwebel
2010-11-29 7:34 ` jaume at fqingenieria.es
2010-11-29 7:52 ` Uwe Kleine-König
2010-11-17 21:29 ` [PATCH 29/51] ARM: mx25: dynamically allocate fsl-usb2-udc devices Uwe Kleine-König
2010-11-17 21:29 ` [PATCH 30/51] ARM: mx25: dynamically allocate mxc_pwm devices Uwe Kleine-König
2010-11-17 21:29 ` [PATCH 31/51] ARM: mx25: move registration of gpios to plat-mxc/gpio.c Uwe Kleine-König
2010-11-17 21:30 ` [PATCH 32/51] ARM: mx25: dynamically allocate imx-keypad devices Uwe Kleine-König
2010-11-17 21:30 ` [PATCH 33/51] ARM: mx25: dynamically allocate imxdi_rtc devices Uwe Kleine-König
2010-11-17 21:30 ` [PATCH 34/51] ARM: mx25: dynamically allocatate imx-fb devices Uwe Kleine-König
2010-11-17 21:30 ` [PATCH 35/51] ARM: mx25: dynamically allocate imx2-wdt devices Uwe Kleine-König
2010-11-19 20:31 ` Uwe Kleine-König
2010-11-17 21:30 ` [PATCH 36/51] ARM: mx25: dynamically allocate mx2-camera devices Uwe Kleine-König
2010-11-17 21:30 ` [PATCH 37/51] ARM: mx25: remove now empty devices.h Uwe Kleine-König
2010-11-17 21:30 ` [PATCH 38/51] ARM: imx: move mx25 support to mach-imx Uwe Kleine-König
2010-11-18 6:28 ` Baruch Siach
2010-11-18 6:28 ` Baruch Siach
2010-11-17 21:30 ` [PATCH 39/51] ARM: imx: let IMX_HAVE_PLATFORM_IMX_FB select HAVE_FB_IMX Uwe Kleine-König
2010-11-17 21:30 ` [PATCH 40/51] ARM: imx: let the machines select SOC_IMX{21,27} Uwe Kleine-König
2010-11-17 21:30 ` [PATCH 41/51] ARM: imx: use SOC_IMX25 instead of ARCH_MX25 for multi-SoC Uwe Kleine-König
2010-11-17 21:30 ` [PATCH 42/51] ARM: mx3: move registration of gpios to plat-mxc/gpio.c Uwe Kleine-König
2010-11-17 21:30 ` [PATCH 43/51] ARM: mx3: use an MX35 constant in imx35 only code Uwe Kleine-König
2010-11-17 21:30 ` [PATCH 44/51] ARM: mx3: introduce SOC_IMX31 and SOC_IMX35 Uwe Kleine-König
2010-11-17 21:30 ` [PATCH 45/51] ARM: mx3: dynamically register mxc-mmc devices Uwe Kleine-König
2010-11-17 21:30 ` [PATCH 46/51] ARM: mx3: dynamically allocate mxc_rnga devices Uwe Kleine-König
2010-11-17 23:56 ` Fabio Estevam
2010-11-18 7:45 ` [PATCH v2 " Uwe Kleine-König
2010-11-17 21:30 ` [PATCH 47/51] ARM: mx3: dynamically allocate fsl-usb2-udc devices Uwe Kleine-König
2010-11-17 21:30 ` [PATCH 48/51] ARM: mx3: dynamically allocate mxc-ehci devices Uwe Kleine-König
2010-11-17 21:30 ` [PATCH 49/51] ARM: mx3: dynamically allocate imx2-wdt devices Uwe Kleine-König
2010-11-17 21:30 ` [PATCH 50/51] ARM: mx3: dynamically allocate imx-keypad devices Uwe Kleine-König
2010-11-17 21:30 ` [PATCH 51/51] ARM: mx3/mx35_3ds: Add watchdog support Uwe Kleine-König
2010-11-18 1:56 ` [PATCH 00/51] some more imx patches for 2.6.38 Shawn Guo
2010-11-18 7:37 ` Uwe Kleine-König
2010-11-18 7:49 ` Sascha Hauer
2010-11-18 8:43 ` Eric Bénard
2010-11-18 9:25 ` Uwe Kleine-König
2010-11-19 20:58 ` Uwe Kleine-König
2010-11-19 21:02 ` [PATCH 52/51] ARM: imx: fix name for functions adding sdhci-esdhc-imx devices Uwe Kleine-König
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=4CEFD139.8090600@gandalf.sssup.it \
--to=trimarchi@gandalf.sssup.it \
--cc=linux-arm-kernel@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.