Re: PHY/FEC Network adapter failed to initialize on MPC52xx Board

["Peter Kuennemann@Crane-Soft" <pkue@crane-soft.de>]

Tanks to all for the reply to this thread. I got the tip from the thread Tiejun
mentioned.

Quotation: 'St. Strobel' in Xenomai-help

"I had this problem too. In my case the problem was caused by an incorrect port multiplex configuration in U-Boot, see CONIFG_SYS_GPS_PORT_CONFIG (I use 0x xxx5xxxx, which corresponds to 10/100Mbit
Eth with MD). "

That fixed it for me.

Regards, Peter

Am 29.11.2010 03:48, schrieb tiejun.chen:
> Peter wrote:
>> Hi all
>>
>> I got completely stuck with a network adapter problem on my
>> ppc board (MPC52xx style). The ntwork adapter does not seem
>> to intialize correctly when booted without 'help from uboot'
>>
> Looks your problem is very similar to one I replied here not long ago :) That is
> also issued from MPC5200. And I remember there was a wrong Port Multiplex
> Configuration.
>
> If possible maybe you can check the email subjected "Problem Ethernet
> Initialization MPC5200 +  LXT971A" on linuxppc-dev list.
>
> Hope its useful.
>
> Tiejun
>
>> The adapter works properly when I first use it with uboot. E.g.
>> using tftp to load the kernel or just issuing a dummy sntp
>> command. It does not get intialized if I boot linux without
>> using any network relevant command in ubboot
>>
>> The difference manifests on the boot message: (working)
>> PHY working
>> ...
>> mpc52xx MII bus: probed
>> TCP cubic registered
>> NET: Registered protocol family 17
>> IP-Config: Complete:
>>      device=eth0, addr=192.168.1.245, mask=255.254.0.0, gw=192.168.1.2,
>>      host=192.168.1.245, domain=, nis-domain=(none),
>>      bootserver=192.168.1.244, rootserver=192.168.1.244, rootpath=
>> Looking up port of RPC 100003/2 on 192.168.1.244
>> Looking up port of RPC 100005/1 on 192.168.1.244
>> VFS: Mounted root (nfs filesystem) on device 0:11.
>> Freeing unused kernel memory: 124k init
>> PHY: f0003000:00 - Link is Up - 100/Full
>>
>> # ping 192.168.1.2  returns proper results.
>>
>> PHY Not working:
>> ...
>> mpc52xx MII bus: probed
>> TCP cubic registered
>> NET: Registered protocol family 17
>> IP-Config: Complete:
>>      device=eth0, addr=192.168.1.245, mask=255.254.0.0, gw=192.168.1.2,
>>      host=192.168.1.245, domain=, nis-domain=(none),
>>      bootserver=192.168.1.244, rootserver=192.168.1.244, rootpath=
>> VFS: Mounted root (squashfs filesystem) readonly on device 31:3.
>> Freeing unused kernel memory: 124k init
>>
>> # ping 192.168.1.2  hangs
>>
>>
>> The second snipped does not have "Looking up.." messages because it
>> boots from flash. Main difference is "PHY: f0003000:00 - Link is Up - 100/Full"
>> which does not appear at the failing case.
>>
>> Linux Version is 2.6.35.7 patched with xenomai 2.5
>> U-Boot 2010.06 (Aug 05 2010 - 19:54:45)
>>
>> Linux configuration see below: ( i left most entries out that are not set)
>> I also experimented with different settings but finally only
>> CONFIG_FEC_MPC52xx=y  and CONFIG_FEC_MPC52xx_MDIO=y
>> seem to be of any relevance. If both are set, the adapter works
>> when initialized by uboot.
>>
>> Any help or tips will be very much appreciated,
>>
>> Regards, Peter
>>
>>
>> Linux .config
>>
>> ...
>> #
>> # Platform support
>> #
>> # CONFIG_PPC_CHRP is not set
>> # CONFIG_MPC5121_ADS is not set
>> # CONFIG_MPC5121_GENERIC is not set
>> CONFIG_PPC_MPC52xx=y
>> CONFIG_PPC_MPC5200_SIMPLE=y
>> # CONFIG_PPC_EFIKA is not set
>> CONFIG_PPC_LITE5200=y
>> # CONFIG_PPC_MEDIA5200 is not set
>> CONFIG_PPC_MPC5200_BUGFIX=y
>> # CONFIG_PPC_MPC5200_GPIO is not set
>> CONFIG_PPC_MPC5200_LPBFIFO=y
>>
>> CONFIG_PPC_BESTCOMM=y
>> CONFIG_PPC_BESTCOMM_FEC=y
>> CONFIG_PPC_BESTCOMM_GEN_BD=y
>> # CONFIG_SIMPLE_GPIO is not set
>> ..
>> # Bus options
>> #
>> CONFIG_ZONE_DMA=y
>> CONFIG_NEED_SG_DMA_LENGTH=y
>> CONFIG_GENERIC_ISA_DMA=y
>> CONFIG_PPC_PCI_CHOICE=y
>> ...
>> #
>> # Generic Driver Options
>> #
>> CONFIG_STANDALONE=y
>> CONFIG_PREVENT_FIRMWARE_BUILD=y
>> CONFIG_MTD=y
>> CONFIG_MTD_PARTITIONS=y
>> CONFIG_MTD_CMDLINE_PARTS=y
>>
>> #
>> # MII PHY device drivers
>> #
>> CONFIG_LXT_PHY=y                        ## Does not seem to have any influence
>> CONFIG_NET_ETHERNET=y
>> CONFIG_MII=y
>> CONFIG_ETHOC=y                           ## Does not seem to have any influence
>> CONFIG_FEC_MPC52xx=y              ## Must be Y in roder to get adapter working with uboot's init
>> CONFIG_FEC_MPC52xx_MDIO=y  ## Must be Y in roder to get adapter working with uboot's init
> _______________________________________________
> Linuxppc-dev mailing list
> Linuxppc-dev@lists.ozlabs.org
> https://lists.ozlabs.org/listinfo/linuxppc-dev