[patch 2/5] ulpi: handle ULPI_OTG_CTRL_CHRGVBUS

[grinberg@compulab.co.il (Igor Grinberg)]

On 12/23/10 22:11, Arnaud Patard (Rtp) wrote:
> Igor Grinberg <grinberg@compulab.co.il> writes:
>
>> Hi Arnaud,
>>
>> On 12/20/10 17:48, Arnaud Patard (Rtp) wrote:
>>> Current code doesn't handle setting CHRGVBUS when enabling vbus.
>>> Add support for it
>>>
>>>
>>>
>>> Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
>>> Index: tst-usb/drivers/usb/otg/ulpi.c
>>> ===================================================================
>>> --- tst-usb.orig/drivers/usb/otg/ulpi.c	2010-12-20 15:38:41.000000000 +0100
>>> +++ tst-usb/drivers/usb/otg/ulpi.c	2010-12-20 15:38:57.000000000 +0100
>>> @@ -234,7 +234,8 @@
>>>  {
>>>  	unsigned int flags = otg_io_read(otg, ULPI_OTG_CTRL);
>>>  
>>> -	flags &= ~(ULPI_OTG_CTRL_DRVVBUS | ULPI_OTG_CTRL_DRVVBUS_EXT);
>>> +	flags &= ~(ULPI_OTG_CTRL_DRVVBUS | ULPI_OTG_CTRL_DRVVBUS_EXT |
>>> +			ULPI_OTG_CTRL_CHRGVBUS);
>>>  
>>>  	if (on) {
>>>  		if (otg->flags & ULPI_OTG_DRVVBUS)
>>> @@ -242,6 +243,9 @@
>>>  
>>>  		if (otg->flags & ULPI_OTG_DRVVBUS_EXT)
>>>  			flags |= ULPI_OTG_CTRL_DRVVBUS_EXT;
>>> +
>>> +		if (otg->flags & ULPI_OTG_CHRGVBUS)
>>> +			flags |= ULPI_OTG_CTRL_CHRGVBUS;
>>>  	}
>>>  
>>>  	return otg_io_write(otg, flags, ULPI_OTG_CTRL);
>> I think this is a wrong place to set the ChrgVbus bit.
>> As for ULPI spec. 1.1:
>> "3.8.7.1 Session Request Protocol (SRP)
>> ULPI provides full SRP support. The Link uses the ChrgVbus and DischrgVbus bits
>> in the OTG Control register to begin and end a session."
>>
>> So it is used for SRP.
>> May be it is better to implement
>> int    (*start_srp)(struct otg_transceiver *otg);
>> method for setting this bit?
>>
> I was not sure on where to put this so I took the same approach as the
> fsl bsp which was to set it in this function and to call this function
> _after_ usb_add_hcd() [ see my previous patch ]. Indeed, it fixed my
> issue so I believe it not so bad given that there has already been some
> troubles on the ehci-mxc init.

Well, the problem is that this is supposed to be a generic driver and it should
somehow follow the ULPI spec.
This patch makes it more like mxc specific.

As far as I understand, Session Request Protocol (SRP) allows a B-device (Peripheral)
to nudge an A-device (Host) to turn on the USB's Vbus.
This patch enables SRP along with Vbus, which seems incorrect completely.
ulpi_set_vbus() should set the Vbus (as its name says) and that's it.

Have you tried without this patch or have you just applied it along with other
patches from the fsl bsp?

Also, if this specific patch (2/5) makes your USB (Host as I understand) work,
it makes me think that there could be some problem with your Vbus supply.
Have you checked that?

> Arnaud
>

-- 
Regards,
Igor.