From: Gabor Juhos <juhosg@openwrt.org>
To: Wim Van Sebroeck <wim@iguana.be>
Cc: Ralf Baechle <ralf@linux-mips.org>,
linux-mips@linux-mips.org, Imre Kaloz <kaloz@openwrt.org>,
"Luis R. Rodriguez" <lrodriguez@atheros.com>,
Cliff Holden <Cliff.Holden@Atheros.com>,
Kathy Giori <Kathy.Giori@Atheros.com>,
linux-watchdog@vger.kernel.org
Subject: Re: [PATCH v3 06/16] watchdog: add driver for the Atheros AR71XX/AR724X/AR913X SoCs
Date: Thu, 30 Dec 2010 17:51:51 +0100 [thread overview]
Message-ID: <4D1CB8A7.6010409@openwrt.org> (raw)
In-Reply-To: <20101230102506.GA6521@infomag.iguana.be>
Hi Wim,
>> This patch adds a driver for the built-in hardware watchdog device
>> of the Atheros AR71XX/AR724X/AR913X SoCs.
>>
>> Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
>> Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
>> Cc: Wim Van Sebroeck <wim@iguana.be>
>> Cc: linux-watchdog@vger.kernel.org
>> ---
>>
>> Changes since RFC: ---
>>
>> Changes since v1:
>> - rebased against 2.6.37-rc7
>>
>> Changes since v2: ---
>
> I adapted the code a little bit:
> Changes since v3:
> * remove #ifdef CONFIG_WATCHDOG_NOWAYOUT for nowayout module-parameter.
> * add ath79_wdt_keepalive when doing un unexpected close of /dev/watchdog (the close is considered as communication with /dev/watchdog)
> * replace reboot_notifier with a platform shutdown.
Thanks!
> Attached the new patch. Can you test it?
I have tested that, it works fine. I would have to resend the patch with your
changes?
> PS: is there a reason why you don't add a module-parameter for wdt_timeout?
I have no specific reason, simply i did not need that so far. However I can add
that in a separate patch, or I can integrate that into the current one if you
prefer.
Regards,
Gabor
next prev parent reply other threads:[~2010-12-30 16:52 UTC|newest]
Thread overview: 21+ messages / expand[flat|nested] mbox.gz Atom feed top
2010-12-28 18:20 [PATCH v3 00/16] MIPS: initial support for the Atheros AR71XX/AR724X/AR913X SoCs Gabor Juhos
2010-12-28 18:20 ` [PATCH v3 01/16] MIPS: add initial support for the Atheros AR71XX/AR724X/AR931X SoCs Gabor Juhos
2010-12-28 18:20 ` [PATCH v3 02/16] MIPS: ath79: add GPIOLIB support Gabor Juhos
2010-12-28 18:20 ` [PATCH v3 03/16] MIPS: ath79: utilize the MIPS multi-machine support Gabor Juhos
2010-12-28 18:20 ` [PATCH v3 04/16] MIPS: ath79: add initial support for the Atheros PB44 reference board Gabor Juhos
2010-12-28 18:20 ` [PATCH v3 05/16] MIPS: ath79: add common GPIO LEDs device Gabor Juhos
2010-12-28 18:20 ` [PATCH v3 06/16] watchdog: add driver for the Atheros AR71XX/AR724X/AR913X SoCs Gabor Juhos
2010-12-30 10:25 ` Wim Van Sebroeck
2010-12-30 16:51 ` Gabor Juhos [this message]
2010-12-30 21:56 ` Wim Van Sebroeck
2010-12-28 18:20 ` [PATCH v3 07/16] MIPS: ath79: add common watchdog device Gabor Juhos
2010-12-28 18:20 ` [PATCH v3 08/16] MIPS: ath79: add common GPIO buttons device Gabor Juhos
2010-12-28 18:20 ` [PATCH v3 09/16] spi: add SPI controller driver for the Atheros AR71XX/AR724X/AR913X SoCs Gabor Juhos
2010-12-28 18:20 ` Gabor Juhos
2010-12-28 18:20 ` [PATCH v3 10/16] MIPS: ath79: add common SPI controller device Gabor Juhos
2010-12-28 18:20 ` [PATCH v3 11/16] USB: ehci: add workaround for Synopsys HC bug Gabor Juhos
2010-12-28 18:20 ` [PATCH v3 12/16] USB: ehci: add bus glue for the Atheros AR71XX/AR724X/AR913X SoCs Gabor Juhos
2010-12-28 18:20 ` [PATCH v3 13/16] USB: ohci: add bus glue for the Atheros AR71XX/AR7240 SoCs Gabor Juhos
2010-12-28 18:20 ` [PATCH v3 14/16] MIPS: ath79: add common USB Host Controller device Gabor Juhos
2010-12-28 18:20 ` [PATCH v3 15/16] MIPS: ath79: add initial support for the Atheros AP81 reference board Gabor Juhos
2010-12-28 18:20 ` [PATCH v3 16/16] MIPS: ath79: add common WMAC device for AR913X based boards Gabor Juhos
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=4D1CB8A7.6010409@openwrt.org \
--to=juhosg@openwrt.org \
--cc=Cliff.Holden@Atheros.com \
--cc=Kathy.Giori@Atheros.com \
--cc=kaloz@openwrt.org \
--cc=linux-mips@linux-mips.org \
--cc=linux-watchdog@vger.kernel.org \
--cc=lrodriguez@atheros.com \
--cc=ralf@linux-mips.org \
--cc=wim@iguana.be \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.