From: Manoj <manoj.iyer@canonical.com>
To: Chris Ball <cjb@laptop.org>
Cc: linux-mmc@vger.kernel.org, linux-kernel@vger.kernel.org
Subject: Re: SDHCI: Ricoh [1180:e823] unable to mount MMC cards.
Date: Thu, 31 Mar 2011 11:00:16 -0500 [thread overview]
Message-ID: <4D94A510.4040509@canonical.com> (raw)
In-Reply-To: <m3oc4rz5kp.fsf@pullcord.laptop.org>
Tried your patch, also enabled CONFIG_MMC_DEBUG=y
CONFIG_MMC_RICOH_MMC=y, with the same result. MMC did not mount.
Here is a portion of dmesg:
[ 1.176793] sdhci: Secure Digital Host Controller Interface driver
[ 1.176795] sdhci: Copyright(c) Pierre Ossman
[ 1.178043] sdhci-pci 0000:0d:00.0: SDHCI controller found
[1180:e823] (rev 5)
[ 1.178049] sdhci-pci 0000:0d:00.0: found 1 slot(s)
[ 1.178071] sdhci-pci 0000:0d:00.0: PCI INT A -> GSI 16 (level, low)
-> IRQ 16
[ 1.178139] mmc0: Unknown controller version (2). You may experience
problems.
[ 1.178149] sdhci-pci 0000:0d:00.0: setting latency timer to 64
[ 1.178163] sdhci: ============== REGISTER DUMP ==============
[ 1.178169] sdhci: Sys addr: 0x00000000 | Version: 0x00000502
[ 1.178174] sdhci: Blk size: 0x00000000 | Blk cnt: 0x00000000
[ 1.178180] sdhci: Argument: 0x00000000 | Trn mode: 0x00000000
[ 1.178186] sdhci: Present: 0x01f20000 | Host ctl: 0x00000000
[ 1.178192] sdhci: Power: 0x00000000 | Blk gap: 0x00000000
[ 1.178197] sdhci: Wake-up: 0x00000000 | Clock: 0x00000000
[ 1.178203] sdhci: Timeout: 0x00000000 | Int stat: 0x00000000
[ 1.178209] sdhci: Int enab: 0x00ff0003 | Sig enab: 0x00ff0003
[ 1.178214] sdhci: AC12 err: 0x00000000 | Slot int: 0x00000000
[ 1.178220] sdhci: Caps: 0x21e8c8b2 | Max curr: 0x00000040
[ 1.178226] sdhci: ADMA Err: 0x00000000 | ADMA Ptr: 0x00000000
[ 1.178227] sdhci: ===========================================
[ 1.178250] Registered led device: mmc0::
[ 1.178272] mmc0: clock 0Hz busmode 1 powermode 0 cs 0 Vdd 0 width 0
timing 0
[ 1.178331] mmc0: clock 0Hz busmode 1 powermode 1 cs 0 Vdd 21 width 0
timing 0
[ 1.178409] mmc0: SDHCI controller on PCI [0000:0d:00.0] using ADMA
[ 1.186216] agpgart-intel 0000:00:00.0: Intel Sandybridge Chipset
[ 1.187272] agpgart-intel 0000:00:00.0: detected 65532K stolen
memory, trimming to 32768K
[ 1.190407] e1000e: Intel(R) PRO/1000 Network Driver - 1.0.2-k4
[ 1.190409] e1000e: Copyright (c) 1999 - 2009 Intel Corporation.
[ 1.206059] mmc0: clock 400000Hz busmode 1 powermode 2 cs 0 Vdd 21
width 0 timing 0
[ 1.212187] agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xc0000000
[ 1.212204] ahci 0000:00:1f.2: version 3.0
[ 1.212221] ahci 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 1.212258] alloc irq_desc for 44 on node -1
[ 1.212260] alloc kstat_irqs on node -1
[ 1.212270] ahci 0000:00:1f.2: irq 44 for MSI/MSI-X
[ 1.212309] ahci: SSS flag set, parallel bus scan disabled
[ 1.219649] mmc0: starting CMD52 arg 00000c00 flags 00000195
[ 1.221698] mmc0: req done (CMD52): -123: 00000000 00000000 00000000
00000000
[ 1.221704] mmc0: starting CMD52 arg 80000c08 flags 00000195
[ 1.223714] mmc0: req done (CMD52): -123: 00000000 00000000 00000000
00000000
[ 1.223719] mmc0: clock 400000Hz busmode 1 powermode 2 cs 1 Vdd 21
width 0 timing 0
[ 1.224717] mmc0: starting CMD0 arg 00000000 flags 000000c0
[ 1.226726] mmc0: req done (CMD0): -123: 00000000 00000000 00000000
00000000
[ 1.227723] mmc0: clock 400000Hz busmode 1 powermode 2 cs 0 Vdd 21
width 0 timing 0
[ 1.228720] mmc0: starting CMD8 arg 000001aa flags 000002f5
[ 1.230724] mmc0: req done (CMD8): -123: 00000000 00000000 00000000
00000000
[ 1.230728] mmc0: starting CMD5 arg 00000000 flags 000002e1
[ 1.230919] ahci 0000:00:1f.2: AHCI 0001.0300 32 slots 6 ports 6 Gbps
0x1b impl SATA mode
[ 1.230922] ahci 0000:00:1f.2: flags: 64bit ncq sntf ilck stag pm led
clo pio slum part ems sxs apst
[ 1.230927] ahci 0000:00:1f.2: setting latency timer to 64
[ 1.232731] mmc0: req failed (CMD5): -123, retrying...
[ 1.234730] mmc0: req failed (CMD5): -123, retrying...
[ 1.236730] mmc0: req failed (CMD5): -123, retrying...
[ 1.238731] mmc0: req done (CMD5): -123: 00000000 00000000 00000000
00000000
[ 1.238735] mmc0: starting CMD55 arg 00000000 flags 000000f5
[ 1.240741] mmc0: req done (CMD55): -123: 00000000 00000000 00000000
00000000
[ 1.240746] mmc0: starting CMD55 arg 00000000 flags 000000f5
[ 1.242754] mmc0: req done (CMD55): -123: 00000000 00000000 00000000
00000000
[ 1.242758] mmc0: starting CMD55 arg 00000000 flags 000000f5
[ 1.242895] [drm] Initialized drm 1.1.0 20060810
[ 1.244764] mmc0: req done (CMD55): -123: 00000000 00000000 00000000
00000000
[ 1.244768] mmc0: starting CMD55 arg 00000000 flags 000000f5
[ 1.246774] mmc0: req done (CMD55): -123: 00000000 00000000 00000000
00000000
[ 1.246780] mmc0: starting CMD1 arg 00000000 flags 000000e1
[ 1.248787] mmc0: req done (CMD1): -123: 00000000 00000000 00000000
00000000
[ 1.248792] mmc0: clock 0Hz busmode 1 powermode 0 cs 0 Vdd 0 width 0
timing 0
[ 27.508892] sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000040
[ 27.706286] mmc0: clock 0Hz busmode 1 powermode 1 cs 0 Vdd 21 width 0
timing 0
[ 27.722274] mmc0: clock 400000Hz busmode 1 powermode 2 cs 0 Vdd 21
width 0 timing 0
[ 27.738270] mmc0: starting CMD52 arg 00000c00 flags 00000195
[ 27.738399] sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00018000
[ 27.740399] mmc0: req done (CMD52): -110: 00000000 00000000 00000000
00000000
[ 27.740407] mmc0: starting CMD52 arg 80000c08 flags 00000195
[ 27.740485] sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00018000
[ 27.742492] mmc0: req done (CMD52): -110: 00000000 00000000 00000000
00000000
[ 27.742497] mmc0: clock 400000Hz busmode 1 powermode 2 cs 1 Vdd 21
width 0 timing 0
[ 27.743493] mmc0: starting CMD0 arg 00000000 flags 000000c0
[ 27.743540] sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000001
[ 27.743546] mmc0: req done (CMD0): 0: 00000000 00000000 00000000 00000000
[ 27.744543] mmc0: clock 400000Hz busmode 1 powermode 2 cs 0 Vdd 21
width 0 timing 0
[ 27.745539] mmc0: starting CMD8 arg 000001aa flags 000002f5
[ 27.745580] sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00018000
[ 27.747584] mmc0: req done (CMD8): -110: 00000000 00000000 00000000
00000000
[ 27.747639] mmc0: starting CMD5 arg 00000000 flags 000002e1
[ 27.747675] sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00018000
[ 27.749671] mmc0: req failed (CMD5): -110, retrying...
[ 27.749708] sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00018000
[ 27.751710] mmc0: req failed (CMD5): -110, retrying...
[ 27.751743] sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00018000
[ 27.753738] mmc0: req failed (CMD5): -110, retrying...
[ 27.753771] sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00018000
[ 27.755771] mmc0: req done (CMD5): -110: 00000000 00000000 00000000
00000000
[ 27.755790] mmc0: starting CMD55 arg 00000000 flags 000000f5
[ 27.755826] sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00018000
[ 27.757824] mmc0: req done (CMD55): -110: 00000000 00000000 00000000
00000000
[ 27.757828] mmc0: starting CMD55 arg 00000000 flags 000000f5
[ 27.757863] sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00018000
[ 27.759863] mmc0: req done (CMD55): -110: 00000000 00000000 00000000
00000000
[ 27.759905] mmc0: starting CMD55 arg 00000000 flags 000000f5
[ 27.759941] sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00018000
[ 27.761939] mmc0: req done (CMD55): -110: 00000000 00000000 00000000
00000000
[ 27.761942] mmc0: starting CMD55 arg 00000000 flags 000000f5
[ 27.761981] sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00018000
[ 27.763985] mmc0: req done (CMD55): -110: 00000000 00000000 00000000
00000000
[ 27.764026] mmc0: starting CMD1 arg 00000000 flags 000000e1
[ 27.764060] sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000001
[ 27.764067] mmc0: req done (CMD1): 0: 003f8000 00000000 00000000 00000000
[ 27.764072] mmc0: clock 400000Hz busmode 1 powermode 2 cs 0 Vdd 20
width 0 timing 0
[ 27.764077] mmc0: clock 400000Hz busmode 1 powermode 2 cs 1 Vdd 20
width 0 timing 0
[ 27.765073] mmc0: starting CMD0 arg 00000000 flags 000000c0
[ 27.765096] sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000001
[ 27.765100] mmc0: req done (CMD0): 0: 00000000 00000000 00000000 00000000
[ 27.766094] mmc0: clock 400000Hz busmode 1 powermode 2 cs 0 Vdd 20
width 0 timing 0
[ 27.767090] mmc0: starting CMD1 arg 40300000 flags 000000e1
[ 27.767129] sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000001
[ 27.767142] mmc0: req done (CMD1): 0: 003f8000 00000000 00000000 00000000
[ 27.782251] mmc0: starting CMD1 arg 40300000 flags 000000e1
[ 27.782309] sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000001
[ 27.782324] mmc0: req done (CMD1): 0: 003f8000 00000000 00000000 00000000
[ 27.798246] mmc0: starting CMD1 arg 40300000 flags 000000e1
[ 27.798320] sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000001
[ 27.798336] mmc0: req done (CMD1): 0: 003f8000 00000000 00000000 00000000
[ 27.814242] mmc0: starting CMD1 arg 40300000 flags 000000e1
[ 27.814314] sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000001
[ 27.814331] mmc0: req done (CMD1): 0: 003f8000 00000000 00000000 00000000
[ 27.830232] mmc0: starting CMD1 arg 40300000 flags 000000e1
[ 27.830288] sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000001
[ 27.830304] mmc0: req done (CMD1): 0: 003f8000 00000000 00000000 00000000
[ 27.846231] mmc0: starting CMD1 arg 40300000 flags 000000e1
[ 27.846285] sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000001
[ 27.846301] mmc0: req done (CMD1): 0: 003f8000 00000000 00000000 00000000
[ 27.862226] mmc0: starting CMD1 arg 40300000 flags 000000e1
[ 27.862299] sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000001
[ 27.862315] mmc0: req done (CMD1): 0: 003f8000 00000000 00000000 00000000
[ 27.878217] mmc0: starting CMD1 arg 40300000 flags 000000e1
[ 27.878273] sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000001
[ 27.878290] mmc0: req done (CMD1): 0: 803f8000 00000000 00000000 00000000
[ 27.878303] mmc0: starting CMD2 arg 00000000 flags 00000067
[ 27.878359] sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000001
[ 27.878382] mmc0: req done (CMD2): 0: ffffffff ffffffff ffffffff ffffff00
[ 27.878399] mmc0: starting CMD3 arg 00010000 flags 00000015
[ 27.878438] sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00018000
[ 27.880442] mmc0: req failed (CMD3): -110, retrying...
[ 27.880474] sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00018000
[ 27.882468] mmc0: req failed (CMD3): -110, retrying...
[ 27.882501] sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00018000
[ 27.884498] mmc0: req failed (CMD3): -110, retrying...
[ 27.884532] sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00018000
[ 27.886530] mmc0: req done (CMD3): -110: 00000000 00000000 00000000
00000000
[ 27.886537] mmc0: clock 0Hz busmode 1 powermode 0 cs 0 Vdd 0 width 0
timing 0
[ 27.886548] mmc0: error -110 whilst initialising MMC card
[ 27.886550] mmc0: clock 0Hz busmode 1 powermode 0 cs 0 Vdd 0 width 0
timing 0
Manoj Iyer
Ubuntu/Canonical
Hardware Enablement
On 03/31/2011 10:13 AM, Chris Ball wrote:
> Hi,
>
> On Thu, Mar 31 2011, Manoj wrote:
>>> How about setting CONFIG_MMC_RICOH_MMC?
>>
>> Yes Sir... that was already set.
>> CONFIG_MMC_RICOH_MMC=y
>
> Ah, I think MMC_RICOH_MMC needs to know about this new PCI ID too.
> I don't know whether that code knows how to turn off the MMC controller
> on this model, though.
>
> Please try this patch:
>
> diff --git a/drivers/pci/quirks.c b/drivers/pci/quirks.c
> index bd80f63..0852046 100644
> --- a/drivers/pci/quirks.c
> +++ b/drivers/pci/quirks.c
> @@ -2758,6 +2758,9 @@ static void ricoh_mmc_fixup_r5c832(struct pci_dev *dev)
> }
> DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_RICOH, PCI_DEVICE_ID_RICOH_R5C832, ricoh_mmc_fixup_r5c832);
> DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_RICOH, PCI_DEVICE_ID_RICOH_R5C832, ricoh_mmc_fixup_r5c832);
> +
> +DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_RICOH, PCI_DEVICE_ID_RICOH_R5C823, ricoh_mmc_fixup_r5c832);
> +DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_RICOH, PCI_DEVICE_ID_RICOH_R5C823, ricoh_mmc_fixup_r5c832);
> #endif /*CONFIG_MMC_RICOH_MMC*/
>
> #if defined(CONFIG_DMAR) || defined(CONFIG_INTR_REMAP)
> diff --git a/include/linux/pci_ids.h b/include/linux/pci_ids.h
> index 11fd381..9ec3316 100644
> --- a/include/linux/pci_ids.h
> +++ b/include/linux/pci_ids.h
> @@ -1535,6 +1535,7 @@
> #define PCI_DEVICE_ID_RICOH_RL5C476 0x0476
> #define PCI_DEVICE_ID_RICOH_RL5C478 0x0478
> #define PCI_DEVICE_ID_RICOH_R5C822 0x0822
> +#define PCI_DEVICE_ID_RICOH_R5C823 0x0823
> #define PCI_DEVICE_ID_RICOH_R5C832 0x0832
> #define PCI_DEVICE_ID_RICOH_R5C843 0x0843
>
>
> and post dmesg of the result, as well as whether it worked.
>
> We're trying the 0x832 disable method on an 0x823 controller, so I don't
> know whether that'll work.
>
> Thanks,
>
> - Chris.
next prev parent reply other threads:[~2011-03-31 16:00 UTC|newest]
Thread overview: 17+ messages / expand[flat|nested] mbox.gz Atom feed top
2011-03-30 22:23 SDHCI: Ricoh [1180:e823] unable to mount MMC cards Manoj
2011-03-30 23:04 ` Chris Ball
2011-03-30 23:32 ` Manoj
2011-03-30 23:53 ` Chris Ball
2011-03-31 14:12 ` Manoj
2011-03-31 14:43 ` Chris Ball
2011-03-31 14:41 ` Manoj
2011-03-31 15:13 ` Chris Ball
2011-03-31 16:00 ` Manoj [this message]
2011-03-31 16:31 ` Chris Ball
2011-03-31 17:09 ` Manoj
2011-03-31 17:26 ` Chris Ball
2011-03-31 17:59 ` Manoj
2011-03-31 18:33 ` Chris Ball
2011-03-31 18:47 ` Philip Langdale
2011-03-31 18:47 ` Philip Langdale
2011-03-31 14:47 ` Manoj
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=4D94A510.4040509@canonical.com \
--to=manoj.iyer@canonical.com \
--cc=cjb@laptop.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-mmc@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.