From: Tim Small <tim@seoss.co.uk>
To: Tejun Heo <tj@kernel.org>, Hubert Bailey <hbailey@marvell.com>,
lil@marvell.com,
"linux-ide@vger.kernel.org" <linux-ide@vger.kernel.org>
Subject: Re: SiI 3726 pmp doesn't work with 2.6.38 and Marvell 88SE9123 AHCI controller
Date: Thu, 07 Jul 2011 19:38:59 +0100 [thread overview]
Message-ID: <4E15FD43.6030701@seoss.co.uk> (raw)
In-Reply-To: <4E15FB4A.809@buttersideup.com>
In the same machine as the previous test set, but with 2.6.38 (debian
squeeze backports kernel):
NCQ 1, two drives both connected to 3726 behind the **88SE9123**
(previous mail was for the 88SE9125):
# while true ; do sh -c "(hdparm -t /dev/sdb & hdparm -t /dev/sdc) 2>&1
| grep MB" ; done
Timing buffered disk reads: 190 MB in 3.02 seconds = 62.97 MB/sec
190 MB in 3.02 seconds = 62.99 MB/sec
Timing buffered disk reads: 194 MB in 3.02 seconds = 64.27 MB/sec
194 MB in 3.02 seconds = 64.24 MB/sec
Timing buffered disk reads: 192 MB in 3.01 seconds = 63.87 MB/sec
194 MB in 3.01 seconds = 64.44 MB/sec
Timing buffered disk reads: 194 MB in 3.02 seconds = 64.26 MB/sec
194 MB in 3.02 seconds = 64.23 MB/sec
Timing buffered disk reads: 194 MB in 3.02 seconds = 64.14 MB/sec
194 MB in 3.03 seconds = 64.13 MB/sec
Timing buffered disk reads: 194 MB in 3.02 seconds = 64.31 MB/sec
194 MB in 3.02 seconds = 64.18 MB/sec
Timing buffered disk reads: 194 MB in 3.02 seconds = 64.31 MB/sec
194 MB in 3.02 seconds = 64.15 MB/sec
Timing buffered disk reads: 192 MB in 3.01 seconds = 63.73 MB/sec
196 MB in 3.02 seconds = 64.87 MB/sec
Timing buffered disk reads: 194 MB in 3.02 seconds = 64.16 MB/sec
194 MB in 3.02 seconds = 64.27 MB/sec
Timing buffered disk reads: 192 MB in 3.01 seconds = 63.72 MB/sec
196 MB in 3.02 seconds = 64.83 MB/sec
Timing buffered disk reads: 194 MB in 3.01 seconds = 64.47 MB/sec
192 MB in 3.01 seconds = 63.79 MB/sec
... so it works, but is about 50% slower than the 88SE9125...
change NCQ depth to 31:
# while true ; do sh -c "(hdparm -t /dev/sdb & hdparm -t /dev/sdc) 2>&1
| grep MB" ; done
[after a considerable pause:]
Timing buffered disk reads: 382 MB in 3.01 seconds = 127.10 MB/sec
... i.e. one drive results only, the other read failed, with this in dmesg:
[ 2930.016043] ata7.00: failed to read SCR 1 (Emask=0x40)
[ 2930.020801] ata7.01: failed to read SCR 1 (Emask=0x40)
[ 2930.025429] ata7.02: failed to read SCR 1 (Emask=0x40)
[ 2930.029970] ata7.03: failed to read SCR 1 (Emask=0x40)
[ 2930.034447] ata7.04: failed to read SCR 1 (Emask=0x40)
[ 2930.038859] ata7.05: failed to read SCR 1 (Emask=0x40)
[ 2930.043218] ata7.15: exception Emask 0x4 SAct 0x0 SErr 0x0 action 0x6
frozen
[ 2930.047661] ata7.00: exception Emask 0x100 SAct 0xc SErr 0x0 action
0x6 frozen
[ 2930.052077] ata7.00: failed command: READ FPDMA QUEUED
[ 2930.056439] ata7.00: cmd 60/00:10:00:06:00/01:00:00:00:00/40 tag 2
ncq 131072 in
[ 2930.056443] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask
0x4 (timeout)
[ 2930.065295] ata7.00: status: { DRDY }
[ 2930.069753] ata7.00: failed command: READ FPDMA QUEUED
[ 2930.074243] ata7.00: cmd 60/00:18:00:07:00/01:00:00:00:00/40 tag 3
ncq 131072 in
[ 2930.074247] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask
0x4 (timeout)
[ 2930.083380] ata7.00: status: { DRDY }
[ 2930.087981] ata7.01: exception Emask 0x100 SAct 0x3 SErr 0x0 action
0x6 frozen
[ 2930.092672] ata7.01: failed command: READ FPDMA QUEUED
[ 2930.097279] ata7.01: cmd 60/00:00:00:06:00/01:00:00:00:00/40 tag 0
ncq 131072 in
[ 2930.097283] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask
0x4 (timeout)
[ 2930.106463] ata7.01: status: { DRDY }
[ 2930.111040] ata7.01: failed command: READ FPDMA QUEUED
[ 2930.115630] ata7.01: cmd 60/00:08:00:07:00/01:00:00:00:00/40 tag 1
ncq 131072 in
[ 2930.115634] res 40/00:01:00:00:00/00:00:00:00:00/00 Emask
0x4 (timeout)
[ 2930.124786] ata7.01: status: { DRDY }
[ 2930.129349] ata7.02: exception Emask 0x100 SAct 0x0 SErr 0x0 action
0x6 frozen
[ 2930.133977] ata7.03: exception Emask 0x100 SAct 0x0 SErr 0x0 action
0x6 frozen
[ 2930.138537] ata7.04: exception Emask 0x100 SAct 0x0 SErr 0x0 action
0x6 frozen
[ 2930.143074] ata7.05: exception Emask 0x100 SAct 0x0 SErr 0x0 action
0x6 frozen
[ 2930.147538] ata7.15: hard resetting link
[ 2930.864034] ata7.15: SATA link up 3.0 Gbps (SStatus 123 SControl 370)
[ 2930.868757] ata7.15: Port Multiplier vendor mismatch '0x1095' != '0x0'
[ 2930.873236] ata7.15: PMP revalidation failed (errno=-19)
[ 2935.868025] ata7.15: hard resetting link
[ 2936.588038] ata7.15: SATA link up 3.0 Gbps (SStatus 123 SControl 370)
[ 2936.592742] ata7.15: Port Multiplier vendor mismatch '0x1095' != '0x0'
[ 2936.597296] ata7.15: PMP revalidation failed (errno=-19)
[ 2936.601803] ata7.15: limiting SATA link speed to 1.5 Gbps
[ 2941.592044] ata7.15: hard resetting link
[ 2942.312039] ata7.15: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 2942.316762] ata7.15: Port Multiplier vendor mismatch '0x1095' != '0x0'
[ 2942.321236] ata7.15: PMP revalidation failed (errno=-19)
[ 2942.325672] ata7.15: failed to recover PMP after 5 tries, giving up
[ 2942.330101] ata7.15: Port Multiplier detaching
[ 2942.334489] ata7.00: disabled
[ 2942.338863] ata7.01: disabled
[ 2942.343145] ata7.00: disabled
[ 2947.316024] ata7: hard resetting link
[ 2948.036036] ata7: SATA link up 3.0 Gbps (SStatus 123 SControl 370)
[ 2948.040497] ata7.15: Port Multiplier 1.1, 0x1095:0x3726 r23, 6 ports,
feat 0x1/0x9
[ 2948.044701] ahci 0000:02:00.0: FBS is enabled.
[ 2948.049005] ata7.00: hard resetting link
[ 2948.368250] ata7.00: SATA link up 3.0 Gbps (SStatus 123 SControl 320)
[ 2948.372472] ata7.01: hard resetting link
[ 2948.696248] ata7.01: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 2948.700471] ata7.02: hard resetting link
[ 2949.024255] ata7.02: SATA link down (SStatus 0 SControl 320)
[ 2949.028581] ata7.03: hard resetting link
[ 2949.352249] ata7.03: SATA link down (SStatus 0 SControl 320)
[ 2949.356582] ata7.04: hard resetting link
[ 2949.680248] ata7.04: SATA link down (SStatus 0 SControl 320)
[ 2949.684638] ata7.05: hard resetting link
[ 2950.008192] ata7.05: failed to write SCR 1 (Emask=0x1)
[ 2950.012618] ata7.05: SATA link down (SStatus 0 SControl 0)
[ 2950.018426] ata7.00: ATA-8: Hitachi HDS5C3020ALA632, ML6OA580, max
UDMA/133
[ 2950.022698] ata7.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth
31/32), AA
[ 2950.028551] ata7.00: configured for UDMA/133
[ 2950.034073] ata7.01: native sectors (2) is smaller than sectors
(3907029168)
[ 2950.038668] ata7.01: ATA-8: Hitachi HDS5C3020ALA632, ML6OA580, max
UDMA/133
[ 2950.043219] ata7.01: 3907029168 sectors, multi 0: LBA48 NCQ (depth
31/32), AA
[ 2950.049087] ata7.01: configured for UDMA/133
[ 2950.053758] ata7.01: device reported invalid CHS sector 0
[ 2950.058290] ata7.01: device reported invalid CHS sector 0
[ 2950.062735] ata7.00: device reported invalid CHS sector 0
[ 2950.067131] ata7.00: device reported invalid CHS sector 0
[ 2950.071451] sd 6:1:0:0: [sdc] Result: hostbyte=DID_OK
driverbyte=DRIVER_SENSE
[ 2950.075844] sd 6:1:0:0: [sdc] Sense Key : Aborted Command [current]
[descriptor]
[ 2950.080228] Descriptor sense data with sense descriptors (in hex):
[ 2950.084616] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
[ 2950.089114] 00 00 00 00
[ 2950.093453] sd 6:1:0:0: [sdc] Add. Sense: No additional sense
information
[ 2950.097839] sd 6:1:0:0: [sdc] CDB: Read(10): 28 00 00 00 06 00 00 01
00 00
[ 2950.102283] end_request: I/O error, dev sdc, sector 1536
[ 2950.106652] quiet_error: 45 callbacks suppressed
[ 2950.110957] Buffer I/O error on device sdc, logical block 192
[ 2950.115306] Buffer I/O error on device sdc, logical block 193
[ 2950.119578] Buffer I/O error on device sdc, logical block 194
[ 2950.123816] Buffer I/O error on device sdc, logical block 195
[ 2950.127958] Buffer I/O error on device sdc, logical block 196
[ 2950.132036] Buffer I/O error on device sdc, logical block 197
[ 2950.136119] Buffer I/O error on device sdc, logical block 198
[ 2950.140190] Buffer I/O error on device sdc, logical block 199
[ 2950.144269] Buffer I/O error on device sdc, logical block 200
[ 2950.148281] Buffer I/O error on device sdc, logical block 201
[ 2950.152265] sd 6:1:0:0: [sdc] Result: hostbyte=DID_OK
driverbyte=DRIVER_SENSE
[ 2950.156275] sd 6:1:0:0: [sdc] Sense Key : Aborted Command [current]
[descriptor]
[ 2950.160289] Descriptor sense data with sense descriptors (in hex):
[ 2950.164318] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
[ 2950.168471] 00 00 00 00
[ 2950.172471] sd 6:1:0:0: [sdc] Add. Sense: No additional sense
information
[ 2950.176525] sd 6:1:0:0: [sdc] CDB: Read(10): 28 00 00 00 07 00 00 01
00 00
[ 2950.180659] end_request: I/O error, dev sdc, sector 1792
[ 2950.184743] sd 6:0:0:0: [sdb] Result: hostbyte=DID_OK
driverbyte=DRIVER_SENSE
[ 2950.188856] sd 6:0:0:0: [sdb] Sense Key : Aborted Command [current]
[descriptor]
[ 2950.192976] Descriptor sense data with sense descriptors (in hex):
[ 2950.197094] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
[ 2950.201337] 00 00 00 00
[ 2950.205439] sd 6:0:0:0: [sdb] Add. Sense: No additional sense
information
[ 2950.209626] sd 6:0:0:0: [sdb] CDB: Read(10): 28 00 00 00 06 00 00 01
00 00
[ 2950.213939] end_request: I/O error, dev sdb, sector 1536
[ 2950.218252] sd 6:0:0:0: [sdb] Result: hostbyte=DID_OK
driverbyte=DRIVER_SENSE
[ 2950.222627] sd 6:0:0:0: [sdb] Sense Key : Aborted Command [current]
[descriptor]
[ 2950.227010] Descriptor sense data with sense descriptors (in hex):
[ 2950.231370] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
[ 2950.235813] 00 00 00 00
[ 2950.240143] sd 6:0:0:0: [sdb] Add. Sense: No additional sense
information
[ 2950.244528] sd 6:0:0:0: [sdb] CDB: Read(10): 28 00 00 00 07 00 00 01
00 00
[ 2950.248975] end_request: I/O error, dev sdb, sector 1792
[ 2950.253351] ata7: EH complete
[ 2950.257986] ata7.00: detaching (SCSI 6:0:0:0)
[ 2950.260412] sd 6:1:0:0: rejecting I/O to offline device
[ 2950.262676] sd 6:0:0:0: rejecting I/O to offline device
[ 2950.272236] sd 6:0:0:0: [sdb] Synchronizing SCSI cache
[ 2950.274778] sd 6:0:0:0: [sdb] Stopping disk
[ 2950.284568] end_request: I/O error, dev sdb, sector 0
[ 2950.287099] sd 6:1:0:0: rejecting I/O to offline device
[ 2950.288321] end_request: I/O error, dev sdc, sector 0
[ 2950.291531] end_request: I/O error, dev sdb, sector 0
[ 2950.293912] sd 6:1:0:0: rejecting I/O to offline device
[ 2950.296077] end_request: I/O error, dev sdc, sector 0
[ 2950.868137] ata7.01: detaching (SCSI 6:1:0:0)
[ 2950.879987] sd 6:1:0:0: [sdc] Synchronizing SCSI cache
[ 2950.884351] sd 6:1:0:0: [sdc] Stopping disk
[ 2951.490748] scsi 6:0:0:0: Direct-Access ATA Hitachi HDS5C302
ML6O PQ: 0 ANSI: 5
[ 2951.497341] sd 6:0:0:0: [sdb] 3907029168 512-byte logical blocks:
(2.00 TB/1.81 TiB)
[ 2951.501834] sd 6:0:0:0: [sdb] Write Protect is off
[ 2951.506067] sd 6:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 2951.506855] scsi 6:1:0:0: Direct-Access ATA Hitachi HDS5C302
ML6O PQ: 0 ANSI: 5
[ 2951.518252] sd 6:0:0:0: [sdb] Write cache: enabled, read cache:
enabled, doesn't support DPO or FUA
[ 2951.523911] sd 6:1:0:0: [sdc] 3907029168 512-byte logical blocks:
(2.00 TB/1.81 TiB)
[ 2951.530008] sd 6:1:0:0: [sdc] Write Protect is off
[ 2951.532522] sd 6:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 2951.533349] sd 6:1:0:0: [sdc] Write cache: enabled, read cache:
enabled, doesn't support DPO or FUA
[ 2953.444386] sdc: sdc1
[ 2953.450667] sd 6:1:0:0: [sdc] Attached SCSI disk
[ 2954.301886] sdb: sdb1
[ 2954.311753] sd 6:0:0:0: [sdb] Attached SCSI disk
[ 2994.016046] ata7.00: failed to read SCR 1 (Emask=0x40)
[ 2994.020684] ata7.01: failed to read SCR 1 (Emask=0x40)
[ 2994.025282] ata7.02: failed to read SCR 1 (Emask=0x40)
[ 2994.029859] ata7.03: failed to read SCR 1 (Emask=0x40)
[ 2994.034443] ata7.04: failed to read SCR 1 (Emask=0x40)
[ 2994.039024] ata7.05: failed to read SCR 1 (Emask=0x40)
[ 2994.043613] ata7.15: exception Emask 0x4 SAct 0x0 SErr 0x400000
action 0x6 frozen
[ 2994.048221] ata7.15: SError: { Handshk }
[ 2994.052790] ata7.00: exception Emask 0x100 SAct 0xa SErr 0x0 action
0x6 frozen
[ 2994.057393] ata7.00: failed command: READ FPDMA QUEUED
[ 2994.061957] ata7.00: cmd 60/00:08:00:18:00/01:00:00:00:00/40 tag 1
ncq 131072 in
[ 2994.061961] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask
0x4 (timeout)
[ 2994.071179] ata7.00: status: { DRDY }
[ 2994.075747] ata7.00: failed command: READ FPDMA QUEUED
[ 2994.080311] ata7.00: cmd 60/00:18:00:19:00/01:00:00:00:00/40 tag 3
ncq 131072 in
[ 2994.080314] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask
0x4 (timeout)
[ 2994.089460] ata7.00: status: { DRDY }
[ 2994.093974] ata7.01: exception Emask 0x100 SAct 0x5 SErr 0x0 action
0x6 frozen
[ 2994.098544] ata7.01: failed command: READ FPDMA QUEUED
[ 2994.103096] ata7.01: cmd 60/00:00:00:04:00/01:00:00:00:00/40 tag 0
ncq 131072 in
[ 2994.103099] res 40/00:01:00:00:00/00:00:00:00:00/00 Emask
0x4 (timeout)
[ 2994.112254] ata7.01: status: { DRDY }
[ 2994.116770] ata7.01: failed command: READ FPDMA QUEUED
[ 2994.121280] ata7.01: cmd 60/00:10:00:05:00/01:00:00:00:00/40 tag 2
ncq 131072 in
[ 2994.121283] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask
0x4 (timeout)
[ 2994.130329] ata7.01: status: { DRDY }
[ 2994.134794] ata7.02: exception Emask 0x100 SAct 0x0 SErr 0x0 action
0x6 frozen
[ 2994.139343] ata7.03: exception Emask 0x100 SAct 0x0 SErr 0x0 action
0x6 frozen
[ 2994.143815] ata7.04: exception Emask 0x100 SAct 0x0 SErr 0x0 action
0x6 frozen
[ 2994.148233] ata7.05: exception Emask 0x100 SAct 0x0 SErr 0x0 action
0x6 frozen
[ 2994.152588] ata7.15: hard resetting link
[ 2994.872040] ata7.15: SATA link up 3.0 Gbps (SStatus 123 SControl 370)
[ 2994.876666] ata7.15: Port Multiplier vendor mismatch '0x1095' != '0x0'
[ 2994.881056] ata7.15: PMP revalidation failed (errno=-19)
[ 2999.876031] ata7.15: hard resetting link
[ 3000.596037] ata7.15: SATA link up 3.0 Gbps (SStatus 123 SControl 370)
[ 3000.600759] ata7.15: Port Multiplier vendor mismatch '0x1095' != '0x0'
[ 3000.605307] ata7.15: PMP revalidation failed (errno=-19)
[ 3000.609803] ata7.15: limiting SATA link speed to 1.5 Gbps
[ 3005.600038] ata7.15: hard resetting link
[ 3006.320038] ata7.15: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 3006.324835] ata7.15: Port Multiplier vendor mismatch '0x1095' != '0x0'
[ 3006.329398] ata7.15: PMP revalidation failed (errno=-19)
[ 3006.333932] ata7.15: failed to recover PMP after 5 tries, giving up
[ 3006.338486] ata7.15: Port Multiplier detaching
[ 3006.343045] ata7.00: disabled
[ 3006.347531] ata7.01: disabled
[ 3006.351918] ata7.00: disabled
[ 3011.324021] ata7: hard resetting link
[ 3012.044038] ata7: SATA link up 3.0 Gbps (SStatus 123 SControl 370)
[ 3012.048607] ata7.15: Port Multiplier 1.1, 0x1095:0x3726 r23, 6 ports,
feat 0x1/0x9
[ 3012.052909] ahci 0000:02:00.0: FBS is enabled.
[ 3012.057467] ata7.00: hard resetting link
[ 3012.376255] ata7.00: SATA link up 3.0 Gbps (SStatus 123 SControl 320)
[ 3012.380560] ata7.01: hard resetting link
[ 3012.704248] ata7.01: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 3012.708580] ata7.02: hard resetting link
[ 3013.032247] ata7.02: SATA link down (SStatus 0 SControl 320)
[ 3013.036615] ata7.03: hard resetting link
[ 3013.360248] ata7.03: SATA link down (SStatus 0 SControl 320)
[ 3013.364635] ata7.04: hard resetting link
[ 3013.688246] ata7.04: SATA link down (SStatus 0 SControl 320)
[ 3013.692689] ata7.05: hard resetting link
[ 3014.016194] ata7.05: failed to write SCR 1 (Emask=0x1)
[ 3014.020635] ata7.05: SATA link down (SStatus 0 SControl 0)
[ 3014.026285] ata7.00: ATA-8: Hitachi HDS5C3020ALA632, ML6OA580, max
UDMA/133
[ 3014.030646] ata7.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth
31/32), AA
[ 3014.036430] ata7.00: configured for UDMA/133
[ 3014.042023] ata7.01: native sectors (2) is smaller than sectors
(3907029168)
[ 3014.046718] ata7.01: ATA-8: Hitachi HDS5C3020ALA632, ML6OA580, max
UDMA/133
[ 3014.051279] ata7.01: 3907029168 sectors, multi 0: LBA48 NCQ (depth
31/32), AA
[ 3014.057159] ata7.01: configured for UDMA/133
[ 3014.059537] ata7.01: device reported invalid CHS sector 0
[ 3014.061890] ata7.00: device reported invalid CHS sector 0
[ 3014.064203] ata7.01: device reported invalid CHS sector 0
[ 3014.066474] ata7.00: device reported invalid CHS sector 0
[ 3014.068733] sd 6:1:0:0: [sdc] Result: hostbyte=DID_OK
driverbyte=DRIVER_SENSE
[ 3014.071007] sd 6:1:0:0: [sdc] Sense Key : Aborted Command [current]
[descriptor]
[ 3014.073291] Descriptor sense data with sense descriptors (in hex):
[ 3014.075562] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
[ 3014.077904] 00 00 00 00
[ 3014.080183] sd 6:1:0:0: [sdc] Add. Sense: No additional sense
information
[ 3014.082476] sd 6:1:0:0: [sdc] CDB: Read(10): 28 00 00 00 04 00 00 01
00 00
[ 3014.084797] end_request: I/O error, dev sdc, sector 1024
[ 3014.087077] quiet_error: 118 callbacks suppressed
[ 3014.089320] Buffer I/O error on device sdc, logical block 128
[ 3014.091593] Buffer I/O error on device sdc, logical block 129
[ 3014.093817] Buffer I/O error on device sdc, logical block 130
[ 3014.096015] Buffer I/O error on device sdc, logical block 131
[ 3014.098167] Buffer I/O error on device sdc, logical block 132
[ 3014.100286] Buffer I/O error on device sdc, logical block 133
[ 3014.102402] Buffer I/O error on device sdc, logical block 134
[ 3014.104521] Buffer I/O error on device sdc, logical block 135
[ 3014.106638] Buffer I/O error on device sdc, logical block 136
[ 3014.108721] Buffer I/O error on device sdc, logical block 137
[ 3014.110792] sd 6:0:0:0: [sdb] Result: hostbyte=DID_OK
driverbyte=DRIVER_SENSE
[ 3014.112877] sd 6:0:0:0: [sdb] Sense Key : Aborted Command [current]
[descriptor]
[ 3014.114966] Descriptor sense data with sense descriptors (in hex):
[ 3014.117053] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
[ 3014.119211] 00 00 00 00
[ 3014.121313] sd 6:0:0:0: [sdb] Add. Sense: No additional sense
information
[ 3014.123421] sd 6:0:0:0: [sdb] CDB: Read(10): 28 00 00 00 18 00 00 01
00 00
[ 3014.125605] end_request: I/O error, dev sdb, sector 6144
[ 3014.127754] sd 6:1:0:0: [sdc] Result: hostbyte=DID_OK
driverbyte=DRIVER_SENSE
[ 3014.129913] sd 6:1:0:0: [sdc] Sense Key : Aborted Command [current]
[descriptor]
[ 3014.132067] Descriptor sense data with sense descriptors (in hex):
[ 3014.134199] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
[ 3014.136423] 00 00 00 00
[ 3014.138587] sd 6:1:0:0: [sdc] Add. Sense: No additional sense
information
[ 3014.140791] sd 6:1:0:0: [sdc] CDB: Read(10): 28 00 00 00 05 00 00 01
00 00
[ 3014.143051] end_request: I/O error, dev sdc, sector 1280
[ 3014.145323] sd 6:0:0:0: [sdb] Result: hostbyte=DID_OK
driverbyte=DRIVER_SENSE
[ 3014.147615] sd 6:0:0:0: [sdb] Sense Key : Aborted Command [current]
[descriptor]
[ 3014.149897] Descriptor sense data with sense descriptors (in hex):
[ 3014.152156] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
[ 3014.154478] 00 00 00 00
[ 3014.156758] sd 6:0:0:0: [sdb] Add. Sense: No additional sense
information
[ 3014.159056] sd 6:0:0:0: [sdb] CDB: Read(10): 28 00 00 00 19 00 00 01
00 00
[ 3014.161406] end_request: I/O error, dev sdb, sector 6400
[ 3014.163703] ata7: EH complete
[ 3014.165979] ata7.00: detaching (SCSI 6:0:0:0)
[ 3014.168308] sd 6:0:0:0: rejecting I/O to offline device
[ 3014.177610] sd 6:0:0:0: [sdb] Synchronizing SCSI cache
[ 3014.179969] sd 6:0:0:0: [sdb] Stopping disk
[ 3014.791747] ata7.01: detaching (SCSI 6:1:0:0)
[ 3014.799621] sd 6:1:0:0: [sdc] Synchronizing SCSI cache
[ 3014.804160] sd 6:1:0:0: [sdc] Stopping disk
[ 3015.419701] scsi 6:0:0:0: Direct-Access ATA Hitachi HDS5C302
ML6O PQ: 0 ANSI: 5
[ 3015.425355] sd 6:0:0:0: [sdb] 3907029168 512-byte logical blocks:
(2.00 TB/1.81 TiB)
[ 3015.429980] sd 6:0:0:0: [sdb] Write Protect is off
[ 3015.434322] sd 6:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 3015.435019] scsi 6:1:0:0: Direct-Access ATA Hitachi HDS5C302
ML6O PQ: 0 ANSI: 5
[ 3015.440304] sd 6:0:0:0: [sdb] Write cache: enabled, read cache:
enabled, doesn't support DPO or FUA
[ 3015.445835] sd 6:1:0:0: [sdc] 3907029168 512-byte logical blocks:
(2.00 TB/1.81 TiB)
[ 3015.450897] sd 6:1:0:0: [sdc] Write Protect is off
[ 3015.455341] sd 6:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 3015.456615] sd 6:1:0:0: [sdc] Write cache: enabled, read cache:
enabled, doesn't support DPO or FUA
[ 3017.371727] sdc: sdc1
[ 3017.377835] sd 6:1:0:0: [sdc] Attached SCSI disk
[ 3018.219239] sdb: sdb1
[ 3018.225421] sd 6:0:0:0: [sdb] Attached SCSI disk
... and the drives have this smartctl output:
SATA Phy Event Counters (GP Log 0x11)
ID Size Value Description
0x0001 2 0 Command failed due to ICRC error
0x0002 2 0 R_ERR response for data FIS
0x0003 2 0 R_ERR response for device-to-host data FIS
0x0004 2 0 R_ERR response for host-to-device data FIS
0x0005 2 0 R_ERR response for non-data FIS
0x0006 2 0 R_ERR response for device-to-host non-data FIS
0x0007 2 0 R_ERR response for host-to-device non-data FIS
0x0009 2 56 Transition from drive PhyRdy to drive PhyNRdy
0x000a 2 35 Device-to-host register FISes sent due to a COMRESET
0x000b 2 0 CRC errors within host-to-device FIS
0x000d 2 0 Non-CRC errors within host-to-device FIS
SATA Phy Event Counters (GP Log 0x11)
ID Size Value Description
0x0001 2 0 Command failed due to ICRC error
0x0002 2 0 R_ERR response for data FIS
0x0003 2 0 R_ERR response for device-to-host data FIS
0x0004 2 0 R_ERR response for host-to-device data FIS
0x0005 2 0 R_ERR response for non-data FIS
0x0006 2 0 R_ERR response for device-to-host non-data FIS
0x0007 2 0 R_ERR response for host-to-device non-data FIS
0x0009 2 9 Transition from drive PhyRdy to drive PhyNRdy
0x000a 2 5 Device-to-host register FISes sent due to a COMRESET
0x000b 2 0 CRC errors within host-to-device FIS
0x000d 2 0 Non-CRC errors within host-to-device FIS
--
South East Open Source Solutions Limited
Registered in England and Wales with company number 06134732.
Registered Office: 2 Powell Gardens, Redhill, Surrey, RH1 1TQ
VAT number: 900 6633 53 http://seoss.co.uk/ +44-(0)1273-808309
next prev parent reply other threads:[~2011-07-07 18:39 UTC|newest]
Thread overview: 14+ messages / expand[flat|nested] mbox.gz Atom feed top
2011-06-07 18:04 SiI 3726 pmp doesn't work with 2.6.38 and Marvell 88SE9123 AHCI controller Tim Small
2011-06-09 14:37 ` Tejun Heo
2011-06-09 21:11 ` Tim Small
2011-06-10 10:24 ` Tejun Heo
2011-06-10 10:31 ` Hubert Bailey
2011-06-10 16:43 ` Tim Small
2011-07-06 20:34 ` Tim Small
2011-07-07 12:13 ` Tim Small
2011-07-07 18:30 ` Tim Small
2011-07-07 18:38 ` Tim Small [this message]
2011-07-08 4:42 ` Hubert Bailey
2011-07-08 9:53 ` Tim Small
2011-07-13 7:34 ` Tejun Heo
2011-07-07 18:43 ` Tim Small
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=4E15FD43.6030701@seoss.co.uk \
--to=tim@seoss.co.uk \
--cc=hbailey@marvell.com \
--cc=lil@marvell.com \
--cc=linux-ide@vger.kernel.org \
--cc=tj@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.