From: Andreas Hartmann <andihartmann@01019freenet.de>
To: Helmut Schaa <helmut.schaa@googlemail.com>
Cc: linux-wireless@vger.kernel.org, users@rt2x00.serialmonkey.com
Subject: Re: rt2x00, AP mode, 802.11n is not working properly
Date: Thu, 21 Jul 2011 17:36:37 +0200 [thread overview]
Message-ID: <4E284785.5090503@01019freenet.de> (raw)
In-Reply-To: <CAGXE3d9HgRvdJModc3hSA25+jLktZJ3i997oq7GfZz4dUJfuvw@mail.gmail.com>
Hello Helmut,
I applied your patch to compat-wireless-2011-07-18 on an Intel Core i5
CPU M460 2.53 GHz (quad core) with kernel
kernel-desktop-3.0.rc7-1.1.x86_64 from OpenSuSE and tested with Linksys
WUSB600N v2 (it's a rt3572 chip) on 40MHz / 802.11n . I just run it a
few days ago with the same compat-wireless package and it was totally
unusable.
With your patch, it's surprisingly running now - ok, the performance is
not as good as with rt3572sta and it isn't stable under high load (you
know - netperf and so ...). It just stalls after a few minutes. There
are at this moment no entries in messages. But before, I get an entry:
Jul 21 16:59:42 pc2 kernel: [20443.730419] phy0 ->
rt2x00usb_watchdog_tx_status: Warning - TX queue 2 status timed out,
invoke forced tx handler
The ping-latency is great - about 0.5 ms (rt3572sta: about 0.7 ms). The
performance with netperf is:
rt3572sta rt2800usb
supplicant -> hostapd 6.3 M/s 4 M/s
hostapd -> supplicant 7.7 M/s 5.7 M/s
If you could increase the stability under load and if you could increase
the performance a bit more, it would be great!
Some device information from messages:
Jul 21 16:58:20 pc2 kernel: [20361.966847] usb 2-1.1: new high speed USB
device number 8 using ehci_hcd
Jul 21 16:58:20 pc2 kernel: [20362.084522] usb 2-1.1: New USB device
found, idVendor=1737, idProduct=0079
Jul 21 16:58:20 pc2 kernel: [20362.084529] usb 2-1.1: New USB device
strings: Mfr=1, Product=2, SerialNumber=3
Jul 21 16:58:20 pc2 kernel: [20362.084534] usb 2-1.1: Product: Linksys
WUSB600N Wireless-N USB Network Adapter with Dual-Band ver. 2
Jul 21 16:58:20 pc2 kernel: [20362.084538] usb 2-1.1: Manufacturer: Linksys
Jul 21 16:58:20 pc2 mtp-probe: checking bus 2, device 8:
"/sys/devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.1"
Jul 21 16:58:20 pc2 mtp-probe: bus: 2, device: 8 was not an MTP device
Jul 21 16:58:20 pc2 kernel: [20362.161618] cfg80211: Calling CRDA to
update world regulatory domain
Jul 21 16:58:20 pc2 kernel: [20362.169831] cfg80211: World regulatory
domain updated:
Jul 21 16:58:20 pc2 kernel: [20362.169839] cfg80211: (start_freq -
end_freq @ bandwidth), (max_antenna_gain, max_eirp)
Jul 21 16:58:20 pc2 kernel: [20362.169841] cfg80211: (2402000 KHz -
2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
Jul 21 16:58:20 pc2 kernel: [20362.169843] cfg80211: (2457000 KHz -
2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
Jul 21 16:58:20 pc2 kernel: [20362.169845] cfg80211: (2474000 KHz -
2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
Jul 21 16:58:20 pc2 kernel: [20362.169847] cfg80211: (5170000 KHz -
5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
Jul 21 16:58:20 pc2 kernel: [20362.169848] cfg80211: (5735000 KHz -
5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
Jul 21 16:58:20 pc2 kernel: [20362.169873] cfg80211: Calling CRDA for
country: DE
Jul 21 16:58:20 pc2 kernel: [20362.176622] cfg80211: Regulatory domain
changed to country: DE
Jul 21 16:58:20 pc2 kernel: [20362.176626] cfg80211: (start_freq -
end_freq @ bandwidth), (max_antenna_gain, max_eirp)
Jul 21 16:58:20 pc2 kernel: [20362.176629] cfg80211: (2400000 KHz -
2483500 KHz @ 40000 KHz), (N/A, 2000 mBm)
Jul 21 16:58:20 pc2 kernel: [20362.176631] cfg80211: (5150000 KHz -
5350000 KHz @ 40000 KHz), (N/A, 2000 mBm)
Jul 21 16:58:20 pc2 kernel: [20362.176633] cfg80211: (5470000 KHz -
5725000 KHz @ 40000 KHz), (N/A, 2698 mBm)
Jul 21 16:58:20 pc2 kernel: [20362.259525] usb 2-1.1: reset high speed
USB device number 8 using ehci_hcd
Jul 21 16:58:20 pc2 kernel: [20362.372816] phy0 -> rt2x00_set_chip: Info
- Chipset detected - rt: 3572, rf: 0009, rev: 0221.
Jul 21 16:58:20 pc2 kernel: [20362.373070] ieee80211 phy0: Selected rate
control algorithm 'minstrel_ht'
Jul 21 16:58:20 pc2 kernel: [20362.374341] Registered led device:
rt2800usb-phy0::radio
Jul 21 16:58:20 pc2 kernel: [20362.374430] Registered led device:
rt2800usb-phy0::assoc
Jul 21 16:58:20 pc2 kernel: [20362.374470] Registered led device:
rt2800usb-phy0::quality
Jul 21 16:58:20 pc2 kernel: [20362.374850] usbcore: registered new
interface driver rt2800usb
Jul 21 16:58:20 pc2 kernel: [20362.395110] udev[7976]: renamed network
interface wlan0 to wlan1
Jul 21 16:58:35 pc2 kernel: [20376.646437] phy0 ->
rt2x00lib_request_firmware: Info - Loading firmware file 'rt2870.bin'.
Jul 21 16:58:35 pc2 kernel: [20376.649110] phy0 ->
rt2x00lib_request_firmware: Info - Firmware detected - version: 0.236.
Jul 21 16:58:35 pc2 kernel: [20376.868997] phy0 -> rt2x00mac_conf_tx:
Info - Configured TX queue 0 - CWmin: 3, CWmax: 4, Aifs: 2, TXop: 102.
Jul 21 16:58:35 pc2 kernel: [20376.870375] phy0 -> rt2x00mac_conf_tx:
Info - Configured TX queue 1 - CWmin: 4, CWmax: 5, Aifs: 2, TXop: 188.
Jul 21 16:58:35 pc2 kernel: [20376.871619] phy0 -> rt2x00mac_conf_tx:
Info - Configured TX queue 2 - CWmin: 5, CWmax: 10, Aifs: 3, TXop: 0.
Jul 21 16:58:35 pc2 kernel: [20376.872867] phy0 -> rt2x00mac_conf_tx:
Info - Configured TX queue 3 - CWmin: 5, CWmax: 10, Aifs: 7, TXop: 0.
Jul 21 16:58:35 pc2 kernel: [20376.874723] ADDRCONF(NETDEV_UP): wlan1:
link is not ready
Jul 21 16:58:38 pc2 kernel: [20380.335178] wlan1: authenticate with
68:7f:74:fb:39:ee (try 1)
Jul 21 16:58:38 pc2 kernel: [20380.336708] wlan1: authenticated
Jul 21 16:58:38 pc2 kernel: [20380.351817] wlan1: associate with
68:7f:74:fb:39:ee (try 1)
Jul 21 16:58:38 pc2 kernel: [20380.354946] wlan1: RX AssocResp from
68:7f:74:fb:39:ee (capab=0x411 status=0 aid=1)
Jul 21 16:58:38 pc2 kernel: [20380.354953] wlan1: associated
Jul 21 16:58:38 pc2 kernel: [20380.355048] phy0 -> rt2x00mac_conf_tx:
Info - Configured TX queue 2 - CWmin: 4, CWmax: 10, Aifs: 3, TXop: 0.
Jul 21 16:58:38 pc2 kernel: [20380.356823] phy0 -> rt2x00mac_conf_tx:
Info - Configured TX queue 3 - CWmin: 4, CWmax: 10, Aifs: 7, TXop: 0.
Jul 21 16:58:38 pc2 kernel: [20380.358414] phy0 -> rt2x00mac_conf_tx:
Info - Configured TX queue 1 - CWmin: 3, CWmax: 4, Aifs: 2, TXop: 93.
Jul 21 16:58:38 pc2 kernel: [20380.359820] phy0 -> rt2x00mac_conf_tx:
Info - Configured TX queue 0 - CWmin: 2, CWmax: 3, Aifs: 2, TXop: 46.
Jul 21 16:58:38 pc2 kernel: [20380.385902] ADDRCONF(NETDEV_CHANGE):
wlan1: link becomes ready
Jul 21 16:58:38 pc2 kernel: [20380.385970] cfg80211: Calling CRDA for
country: DE
Jul 21 16:58:38 pc2 kernel: [20380.390979] cfg80211: Regulatory domain
changed to country: DE
Jul 21 16:58:38 pc2 kernel: [20380.390983] cfg80211: (start_freq -
end_freq @ bandwidth), (max_antenna_gain, max_eirp)
Jul 21 16:58:38 pc2 kernel: [20380.390988] cfg80211: (2400000 KHz -
2483500 KHz @ 40000 KHz), (N/A, 2000 mBm)
Jul 21 16:58:38 pc2 kernel: [20380.390993] cfg80211: (5150000 KHz -
5350000 KHz @ 40000 KHz), (N/A, 2000 mBm)
Jul 21 16:58:38 pc2 kernel: [20380.390996] cfg80211: (5470000 KHz -
5725000 KHz @ 40000 KHz), (N/A, 2698 mBm)
wlan1 IEEE 802.11abgn ESSID:"Hurra"
Mode:Managed Frequency:2.412 GHz Access Point: 11:22:33:44:55:66
Bit Rate=130 Mb/s Tx-Power=20 dBm
Retry long limit:7 RTS thr:off Fragment thr:off
Encryption key:off
Power Management:off
Link Quality=47/70 Signal level=-63 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:79 Missed beacon:0
Kind regards,
Andreas
PS
before this patch, I got millions of entries in messages like this,
absolutely no performance (about 1 k/s or nothing):
Jul 20 17:51:18 pc2 kernel: [ 5496.416075] phy0 ->
rt2800usb_txdone_entry_check: Warning - TX status report missed for
queue 2 entry 63
Jul 20 17:51:18 pc2 kernel: [ 5496.416098] phy0 ->
rt2800usb_txdone_entry_check: Warning - TX status report missed for
queue 2 entry 0
Jul 20 17:51:18 pc2 kernel: [ 5496.416112] phy0 ->
rt2800usb_txdone_entry_check: Warning - TX status report missed for
queue 2 entry 1
Jul 20 17:51:18 pc2 kernel: [ 5496.416128] phy0 ->
rt2800usb_txdone_entry_check: Warning - TX status report missed for
queue 2 entry 3
Jul 20 17:51:18 pc2 kernel: [ 5496.416142] phy0 ->
rt2800usb_txdone_entry_check: Warning - TX status report missed for
queue 2 entry 4
Jul 20 17:51:18 pc2 kernel: [ 5496.416157] phy0 ->
rt2800usb_txdone_entry_check: Warning - TX status report missed for
queue 2 entry 6
Jul 20 17:51:18 pc2 kernel: [ 5496.416170] phy0 ->
rt2800usb_txdone_entry_check: Warning - TX status report missed for
queue 2 entry 7
Jul 20 17:51:18 pc2 kernel: [ 5496.416186] phy0 ->
rt2800usb_txdone_entry_check: Warning - TX status report missed for
queue 2 entry 9
Jul 20 17:51:18 pc2 kernel: [ 5496.416200] phy0 ->
rt2800usb_txdone_entry_check: Warning - TX status report missed for
queue 2 entry 10
Jul 20 17:51:18 pc2 kernel: [ 5496.417799] phy0 ->
rt2800usb_txdone_entry_check: Warning - TX status report missed for
queue 2 entry 12
Jul 20 17:51:18 pc2 kernel: [ 5496.417814] phy0 ->
rt2800usb_txdone_entry_check: Warning - TX status report missed for
queue 2 entry 14
Jul 20 17:51:18 pc2 kernel: [ 5496.417823] phy0 ->
rt2800usb_txdone_entry_check: Warning - TX status report missed for
queue 2 entry 15
Jul 20 17:51:18 pc2 kernel: [ 5496.420927] phy0 ->
rt2800usb_txdone_entry_check: Warning - TX status report missed for
queue 2 entry 16
Jul 20 17:51:18 pc2 kernel: [ 5496.420948] phy0 ->
rt2800usb_txdone_entry_check: Warning - TX status report missed for
queue 2 entry 17
Jul 20 17:51:18 pc2 kernel: [ 5496.421164] phy0 ->
rt2800usb_txdone_entry_check: Warning - TX status report missed for
queue 2 entry 19
Jul 20 17:51:18 pc2 kernel: [ 5496.421169] phy0 ->
rt2800usb_txdone_entry_check: Warning - TX status report missed for
queue 2 entry 20
Jul 20 17:51:18 pc2 kernel: [ 5496.421802] phy0 ->
rt2800usb_txdone_entry_check: Warning - TX status report missed for
queue 2 entry 22
Jul 20 17:51:18 pc2 kernel: [ 5496.421829] phy0 ->
rt2800usb_txdone_entry_check: Warning - TX status report missed for
queue 2 entry 23
Jul 20 17:51:18 pc2 kernel: [ 5496.421922] phy0 ->
rt2800usb_txdone_entry_check: Warning - TX status report missed for
queue 2 entry 25
Jul 20 17:51:18 pc2 kernel: [ 5496.424431] phy0 ->
rt2800usb_txdone_entry_check: Warning - TX status report missed for
queue 2 entry 26
Jul 20 17:51:18 pc2 kernel: [ 5496.424459] phy0 ->
rt2800usb_txdone_entry_check: Warning - TX status report missed for
queue 2 entry 27
Jul 20 17:51:18 pc2 kernel: [ 5496.424683] phy0 ->
rt2800usb_txdone_entry_check: Warning - TX status report missed for
queue 2 entry 29
Jul 20 17:51:18 pc2 kernel: [ 5496.424708] phy0 ->
rt2800usb_txdone_entry_check: Warning - TX status report missed for
queue 2 entry 30
Jul 20 17:51:18 pc2 kernel: [ 5496.424916] phy0 ->
rt2800usb_txdone_entry_check: Warning - TX status report missed for
queue 2 entry 32
prev parent reply other threads:[~2011-07-21 15:35 UTC|newest]
Thread overview: 18+ messages / expand[flat|nested] mbox.gz Atom feed top
2011-07-20 13:16 rt2x00, AP mode, 802.11n is not working properly Stanislav Demakov
2011-07-20 13:36 ` Helmut Schaa
2011-07-20 14:48 ` Stanislav Demakov
2011-07-20 15:09 ` Helmut Schaa
2011-07-20 16:05 ` Juan Carlos Garza Fernandez
2011-07-20 16:55 ` Stanislav Demakov
2011-07-20 16:06 ` Stanislav Demakov
2011-07-21 11:53 ` Stanislav Demakov
2011-07-21 13:49 ` Helmut Schaa
2011-07-21 14:03 ` Stanislav Demakov
2011-07-21 14:13 ` Helmut Schaa
2011-07-21 14:20 ` Stanislav Demakov
2011-07-21 14:43 ` Stanislav Demakov
2011-07-21 18:18 ` Stanislav Demakov
2011-07-22 7:29 ` Helmut Schaa
2011-07-22 7:47 ` Stanislav Demakov
2011-08-02 10:15 ` Stanislav Demakov
2011-07-21 15:36 ` Andreas Hartmann [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=4E284785.5090503@01019freenet.de \
--to=andihartmann@01019freenet.de \
--cc=helmut.schaa@googlemail.com \
--cc=linux-wireless@vger.kernel.org \
--cc=users@rt2x00.serialmonkey.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.