From: Lars-Peter Clausen <lars@metafoo.de>
To: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Takashi Iwai <tiwai@suse.de>,
uclinux-dist-devel@blackfin.uclinux.org,
Scott Jiang <scott.jiang.linux@gmail.com>,
alsa-devel@alsa-project.org, dp@opensource.wolfsonmicro.com
Subject: Re: snd soc spi read/write
Date: Thu, 11 Aug 2011 08:41:45 +0200 [thread overview]
Message-ID: <4E4379A9.6060800@metafoo.de> (raw)
In-Reply-To: <20110811053246.GA16655@opensource.wolfsonmicro.com>
On 08/11/2011 07:32 AM, Mark Brown wrote:
> On Thu, Aug 11, 2011 at 05:09:14AM +0200, Lars-Peter Clausen wrote:
>> On 08/11/2011 04:46 AM, Mark Brown wrote:
>
>>> None of the current ASoC code will coalesce register writes at all, and
>>> in the case where you're doing writes to registers that aren't actually
>>> adjacent it's going to be marginal if it's better to transmit the
>>> intervening register or transmit another register address. That only
>>> really makes a difference during cache sync anyway.
>
>> I was think more in terms of in memory consumption and lookup time of the cache
>> compared to a flat cache. If you have two blocks which have a gap of one
>> register between them and that register gets inserted into the cache, ideally
>> those two blocks would be merged, which doesn't seem to be the case currently.
>> So instead of one rbnode with a block covering the whole register space you'll
>> end up with a lot of smaller rbnodes.
>
> My guess is that it's probably not worth worrying about, especially for
> performance where you mostly just need to be better than physical I/O.
> For small register maps the memory overhead is similarly probably not
> worth worrying about, and obviously there's also LZO.
I think I'll just test it with my codec and see how it turns out. If it there
are dozens of small blocks, instead of a few larger blocks, I'll see if there
is a way to easily improve the situation.
>
>>> Yes, as I said in one of the earlier messages in this thread. It seems
>>> like a good combination of being writable/legible and compact.
>
>> Hm, ok I'll give it a try. Though I'm not sure yet how to efficiently implement
>> the default register lookup when syncing the cache.
>
> The caches can just unpack into their data, we need to take a copy
> anyway to allow the caches to be marked as __initdata and then the data
> will end up stored in a format that matches the method we're using to
> store the data.
>
> Dimitris had done an initial version of the move of the cache over,
> though I didn't review it properly yet and he's on holiday now. I might
> repost it, there were a few issues but it's at least 90% of the way
> there IIRC from the time I had to look at it.
ok, that would be great, thanks.
- Lars
next prev parent reply other threads:[~2011-08-11 6:43 UTC|newest]
Thread overview: 29+ messages / expand[flat|nested] mbox.gz Atom feed top
2011-08-04 10:24 snd soc spi read/write Scott Jiang
2011-08-04 10:35 ` Mark Brown
2011-08-05 2:24 ` Scott Jiang
2011-08-05 5:42 ` Mark Brown
2011-08-05 6:26 ` Scott Jiang
2011-08-05 6:34 ` Mark Brown
[not found] ` <CAHG8p1BBza_M_Cgrq2O2U+Xc-=rPHeNBKMD_KwfZsLX5Npz9jA@mail.gmail.com>
[not found] ` <20110805072908.GA28149@opensource.wolfsonmicro.com>
2011-08-05 8:00 ` Scott Jiang
2011-08-05 8:30 ` Mark Brown
2011-08-09 3:41 ` Scott Jiang
2011-08-09 16:04 ` Mark Brown
2011-08-10 11:54 ` Takashi Iwai
2011-08-10 14:55 ` Mark Brown
2011-08-10 15:00 ` Takashi Iwai
2011-08-10 15:03 ` Mark Brown
2011-08-10 15:15 ` Takashi Iwai
2011-08-10 15:34 ` Mark Brown
2011-08-10 16:02 ` Takashi Iwai
2011-08-11 3:17 ` Mark Brown
2011-08-10 21:31 ` Lars-Peter Clausen
2011-08-11 0:33 ` Mark Brown
2011-08-11 1:50 ` Lars-Peter Clausen
2011-08-11 2:46 ` Mark Brown
2011-08-11 3:09 ` Lars-Peter Clausen
2011-08-11 5:32 ` Mark Brown
2011-08-11 6:41 ` Lars-Peter Clausen [this message]
2011-08-17 9:16 ` Dimitris Papastamos
2011-08-05 6:11 ` Takashi Iwai
2011-08-05 6:21 ` Takashi Iwai
2011-08-05 6:27 ` Mark Brown
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=4E4379A9.6060800@metafoo.de \
--to=lars@metafoo.de \
--cc=alsa-devel@alsa-project.org \
--cc=broonie@opensource.wolfsonmicro.com \
--cc=dp@opensource.wolfsonmicro.com \
--cc=scott.jiang.linux@gmail.com \
--cc=tiwai@suse.de \
--cc=uclinux-dist-devel@blackfin.uclinux.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.