From: Stefan Zwanenburg <stefanhetzwaantje@gmail.com>
To: 李朝明 <chaoming_li@realsil.com.cn>
Cc: 'Larry Finger' <Larry.Finger@lwfinger.net>,
linux-wireless@vger.kernel.org
Subject: Re: 答复: 答复: 答复: RTL8192SE and 802.11n problem
Date: Mon, 19 Sep 2011 22:04:53 +0200 [thread overview]
Message-ID: <4E77A065.4070300@gmail.com> (raw)
In-Reply-To: <1903155944F64F00AC0C401593C20923@realsil.com.cn>
On 09/19/2011 06:41 AM, 李朝明 wrote:
> Dear Sir:
>
> Yes, sniffer can help, Could you help to catch the authentication
> and association packet and send it to me。
>
> Best Regards，
> lizhaoming
>
Find below the output of wpa_supplicant with the -ddd switch. If that is
not the information you required (ie: you need even rawer logging or
somesuch), please tell me what I need to do, or where I might find the
information to do what I need to do.
Initializing interface 'wlan0' conf '/home/psychotic/wpa.conf' driver
'nl80211' ctrl_interface 'N/A' bridge 'N/A'
Configuration file '/home/psychotic/wpa.conf' -> '/home/psychotic/wpa.conf'
Reading configuration file '/home/psychotic/wpa.conf'
ap_scan=1
ctrl_interface='DIR=/var/run/wpa_supplicant GROUP=wheel'
Line: 3 - start of a new network block
ssid - hexdump_ascii(len=10):
50 65 72 66 6f 72 61 74 6f 72 Perforator
scan_ssid=1 (0x1)
proto: 0x3
key_mgmt: 0x2
pairwise: 0x18
group: 0x18
PSK - hexdump(len=32): [REMOVED]
Priority group 0
id=0 ssid='Perforator'
netlink: Operstate: linkmode=1, operstate=5
Own MAC address: 1c:4b:d6:69:6a:dc
wpa_driver_nl80211_set_key: ifindex=6 alg=0 addr=0x450c7b key_idx=0
set_tx=0 seq_len=0 key_len=0
wpa_driver_nl80211_set_key: ifindex=6 alg=0 addr=0x450c7b key_idx=1
set_tx=0 seq_len=0 key_len=0
wpa_driver_nl80211_set_key: ifindex=6 alg=0 addr=0x450c7b key_idx=2
set_tx=0 seq_len=0 key_len=0
wpa_driver_nl80211_set_key: ifindex=6 alg=0 addr=0x450c7b key_idx=3
set_tx=0 seq_len=0 key_len=0
RSN: flushing PMKID list in the driver
Setting scan request: 0 sec 100000 usec
EAPOL: SUPP_PAE entering state DISCONNECTED
EAPOL: Supplicant port status: Unauthorized
EAPOL: KEY_RX entering state NO_KEY_RECEIVE
EAPOL: SUPP_BE entering state INITIALIZE
EAP: EAP entering state DISABLED
EAPOL: Supplicant port status: Unauthorized
EAPOL: Supplicant port status: Unauthorized
ctrl_interface_group=10 (from group name 'wheel')
Added interface wlan0
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
State: DISCONNECTED -> SCANNING
Scan SSID - hexdump_ascii(len=10):
50 65 72 66 6f 72 61 74 6f 72 Perforator
Starting AP scan for wildcard SSID
nl80211: Scan SSID - hexdump_ascii(len=10):
50 65 72 66 6f 72 61 74 6f 72 Perforator
nl80211: Scan SSID - hexdump_ascii(len=0): [NULL]
Scan requested (ret=0) - scan timeout 10 seconds
nl80211: Event message available
nl80211: Scan trigger
EAPOL: disable timer tick
EAPOL: Supplicant port status: Unauthorized
nl80211: Event message available
nl80211: New scan results available
Received scan results (8 BSSes)
BSS: Start scan result update 1
BSS: Add new id 0 BSSID 80:c6:ab:1e:48:d3 SSID 'UPC0038938'
BSS: Add new id 1 BSSID 00:14:7f:c6:a0:bc SSID 'SpeedTouch5E1151'
BSS: Add new id 2 BSSID 00:18:f6:e9:22:07 SSID 'Thomson104ABB'
BSS: Add new id 3 BSSID 00:23:cd:11:e9:c2 SSID 'Sloot'
BSS: Add new id 4 BSSID 00:1e:c1:a2:01:5a SSID 'Perforator'
BSS: Add new id 5 BSSID 00:1e:2a:06:c7:f8 SSID 'NETGEAR'
BSS: Add new id 6 BSSID c0:c1:c0:20:c6:3f SSID 'Cisco36513'
BSS: Add new id 7 BSSID 00:25:9c:df:0a:6d SSID 'Linksys-120n'
New scan results available
Selecting BSS from priority group 0
Try to find WPA-enabled AP
0: 80:c6:ab:1e:48:d3 ssid='UPC0038938' wpa_ie_len=28 rsn_ie_len=24
caps=0x411
skip - SSID mismatch
1: 00:14:7f:c6:a0:bc ssid='SpeedTouch5E1151' wpa_ie_len=24 rsn_ie_len=0
caps=0x411
skip - SSID mismatch
2: 00:18:f6:e9:22:07 ssid='Thomson104ABB' wpa_ie_len=28 rsn_ie_len=24
caps=0x411
skip - SSID mismatch
3: 00:23:cd:11:e9:c2 ssid='Sloot' wpa_ie_len=0 rsn_ie_len=24 caps=0x431
skip - SSID mismatch
4: 00:1e:c1:a2:01:5a ssid='Perforator' wpa_ie_len=0 rsn_ie_len=20 caps=0x411
selected based on RSN IE
selected WPA AP 00:1e:c1:a2:01:5a ssid='Perforator'
Automatic auth_alg selection: 0x1
RSN: using IEEE 802.11i/D9.0
WPA: Selected cipher suites: group 16 pairwise 16 key_mgmt 2 proto 2
WPA: clearing AP WPA IE
WPA: set AP RSN IE - hexdump(len=22): 30 14 01 00 00 0f ac 04 01 00 00
0f ac 04 01 00 00 0f ac 02 01 00
WPA: using GTK CCMP
WPA: using PTK CCMP
WPA: using KEY_MGMT WPA-PSK
WPA: Set own WPA IE default - hexdump(len=22): 30 14 01 00 00 0f ac 04
01 00 00 0f ac 04 01 00 00 0f ac 02 00 00
Cancelling scan request
Trying to authenticate with 00:1e:c1:a2:01:5a (SSID='Perforator'
freq=2442 MHz)
No keys have been configured - skip key clearing
State: SCANNING -> AUTHENTICATING
EAPOL: External notification - EAP success=0
EAPOL: Supplicant port status: Unauthorized
EAPOL: External notification - EAP fail=0
EAPOL: Supplicant port status: Unauthorized
EAPOL: External notification - portControl=Auto
EAPOL: Supplicant port status: Unauthorized
nl80211: Authenticate (ifindex=6)
* bssid=00:1e:c1:a2:01:5a
* freq=2442
* SSID - hexdump_ascii(len=10):
50 65 72 66 6f 72 61 74 6f 72 Perforator
* IEs - hexdump(len=0): [NULL]
* Auth Type 0
nl80211: Authentication request send successfully
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
nl80211: Event message available
nl80211: MLME event 37
nl80211: MLME event frame - hexdump(len=30): b0 00 32 00 1c 4b d6 69 6a
dc 00 1e c1 a2 01 5a 00 1e c1 a2 01 5a d0 3c 00 00 02 00 00 00
SME: Authentication response: peer=00:1e:c1:a2:01:5a auth_type=0
status_code=0
SME: Authentication response IEs - hexdump(len=0): [NULL]
Trying to associate with 00:1e:c1:a2:01:5a (SSID='Perforator' freq=2442 MHz)
State: AUTHENTICATING -> ASSOCIATING
wpa_driver_nl80211_set_operstate: operstate 0->0 (DORMANT)
netlink: Operstate: linkmode=-1, operstate=5
WPA: set own WPA/RSN IE - hexdump(len=22): 30 14 01 00 00 0f ac 04 01 00
00 0f ac 04 01 00 00 0f ac 02 00 00
nl80211: Associate (ifindex=6)
* bssid=00:1e:c1:a2:01:5a
* freq=2442
* SSID - hexdump_ascii(len=10):
50 65 72 66 6f 72 61 74 6f 72 Perforator
* IEs - hexdump(len=22): 30 14 01 00 00 0f ac 04 01 00 00 0f ac 04 01
00 00 0f ac 02 00 00
nl80211: Association request send successfully
nl80211: Event message available
nl80211: Ignored unknown event (cmd=19)
nl80211: Event message available
nl80211: MLME event 38
nl80211: MLME event frame - hexdump(len=55): 10 00 32 00 1c 4b d6 69 6a
dc 00 1e c1 a2 01 5a 00 1e c1 a2 01 5a e0 3c 11 04 00 00 02 c0 01 08 82
84 8b 96 12 24 48 6c 32 04 0c 18 30 60 dd 07 00 0c 43 04 00 00 00
Association info event
resp_ies - hexdump(len=25): 01 08 82 84 8b 96 12 24 48 6c 32 04 0c 18 30
60 dd 07 00 0c 43 04 00 00 00
freq=2442 MHz
State: ASSOCIATING -> ASSOCIATED
wpa_driver_nl80211_set_operstate: operstate 0->0 (DORMANT)
netlink: Operstate: linkmode=-1, operstate=5
Associated to a new BSS: BSSID=00:1e:c1:a2:01:5a
No keys have been configured - skip key clearing
Associated with 00:1e:c1:a2:01:5a
WPA: Association event - clear replay counter
WPA: Clear old PTK
EAPOL: External notification - portEnabled=0
EAPOL: Supplicant port status: Unauthorized
EAPOL: External notification - portValid=0
EAPOL: Supplicant port status: Unauthorized
EAPOL: External notification - EAP success=0
EAPOL: Supplicant port status: Unauthorized
EAPOL: External notification - portEnabled=1
EAPOL: SUPP_PAE entering state CONNECTING
EAPOL: enable timer tick
EAPOL: SUPP_BE entering state IDLE
Setting authentication timeout: 10 sec 0 usec
Cancelling scan request
RTM_NEWLINK: operstate=0 ifi_flags=0x11003 ([UP][LOWER_UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
RTM_NEWLINK: operstate=0 ifi_flags=0x11003 ([UP][LOWER_UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
RTM_NEWLINK: operstate=0 ifi_flags=0x11003 ([UP][LOWER_UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
nl80211: Event message available
nl80211: Ignore connect event (cmd=46) when using userspace SME
RX EAPOL from 00:1e:c1:a2:01:5a
RX EAPOL - hexdump(len=121): 01 03 00 75 02 00 8a 00 10 00 00 00 00 00
00 0a 48 bf 66 e9 22 34 9a 54 97 4a d1 f4 0f 68 ea 96 50 bb 75 fd 8f 8d
ae 98 95 06 c8 d6 60 fd b7 89 1b 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 16 dd 14 00 0f ac 04 3a d1 08 d5 c1
2d d5 21 fd b4 64 fb 3b 2e 1f 46
Setting authentication timeout: 10 sec 0 usec
IEEE 802.1X RX: version=1 type=3 length=117
EAPOL-Key type=2
key_info 0x8a (ver=2 keyidx=0 rsvd=0 Pairwise Ack)
key_length=16 key_data_length=22
replay_counter - hexdump(len=8): 00 00 00 00 00 00 0a 48
key_nonce - hexdump(len=32): bf 66 e9 22 34 9a 54 97 4a d1 f4 0f 68 ea
96 50 bb 75 fd 8f 8d ae 98 95 06 c8 d6 60 fd b7 89 1b
key_iv - hexdump(len=16): 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
key_rsc - hexdump(len=8): 00 00 00 00 00 00 00 00
key_id (reserved) - hexdump(len=8): 00 00 00 00 00 00 00 00
key_mic - hexdump(len=16): 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
WPA: RX EAPOL-Key - hexdump(len=121): 01 03 00 75 02 00 8a 00 10 00 00
00 00 00 00 0a 48 bf 66 e9 22 34 9a 54 97 4a d1 f4 0f 68 ea 96 50 bb 75
fd 8f 8d ae 98 95 06 c8 d6 60 fd b7 89 1b 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 16 dd 14 00 0f ac 04 3a d1
08 d5 c1 2d d5 21 fd b4 64 fb 3b 2e 1f 46
State: ASSOCIATED -> 4WAY_HANDSHAKE
WPA: RX message 1 of 4-Way Handshake from 00:1e:c1:a2:01:5a (ver=2)
RSN: msg 1/4 key data - hexdump(len=22): dd 14 00 0f ac 04 3a d1 08 d5
c1 2d d5 21 fd b4 64 fb 3b 2e 1f 46
WPA: PMKID in EAPOL-Key - hexdump(len=22): dd 14 00 0f ac 04 3a d1 08 d5
c1 2d d5 21 fd b4 64 fb 3b 2e 1f 46
RSN: PMKID from Authenticator - hexdump(len=16): 3a d1 08 d5 c1 2d d5 21
fd b4 64 fb 3b 2e 1f 46
RSN: no matching PMKID found
WPA: Renewed SNonce - hexdump(len=32): d3 ce 10 ea a3 0b 3e b0 bc 40 91
fb f2 ee 00 a2 9e f6 a2 08 50 49 8b fe 94 93 d1 66 9c 62 92 7f
WPA: PTK derivation - A1=1c:4b:d6:69:6a:dc A2=00:1e:c1:a2:01:5a
WPA: PMK - hexdump(len=32): [REMOVED]
WPA: PTK - hexdump(len=48): [REMOVED]
WPA: WPA IE for msg 2/4 - hexdump(len=22): 30 14 01 00 00 0f ac 04 01 00
00 0f ac 04 01 00 00 0f ac 02 00 00
WPA: Sending EAPOL-Key 2/4
WPA: TX EAPOL-Key - hexdump(len=121): 01 03 00 75 02 01 0a 00 00 00 00
00 00 00 00 0a 48 d3 ce 10 ea a3 0b 3e b0 bc 40 91 fb f2 ee 00 a2 9e f6
a2 08 50 49 8b fe 94 93 d1 66 9c 62 92 7f 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 7e 86
e7 f4 dd 37 0a c6 88 2a 45 79 ea 07 9c 2d 00 16 30 14 01 00 00 0f ac 04
01 00 00 0f ac 04 01 00 00 0f ac 02 00 00
RX EAPOL from 00:1e:c1:a2:01:5a
RX EAPOL - hexdump(len=155): 01 03 00 97 02 13 ca 00 10 00 00 00 00 00
00 0a 49 bf 66 e9 22 34 9a 54 97 4a d1 f4 0f 68 ea 96 50 bb 75 fd 8f 8d
ae 98 95 06 c8 d6 60 fd b7 89 1b 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 3f e3 04 00 00 00 00 00 00 00 00 00 00 00 00 00 72 62 5e ad 3f
fa de fa a8 df 9c 8b 28 54 ac 52 00 38 af f7 5a c8 75 be 95 65 97 ce 28
db d4 84 fd 79 db 70 50 31 4e 48 5e 1b dc 04 fa c8 8f 88 ba 1f e8 55 04
60 a0 f2 a5 84 ca 78 bb de db 39 d3 18 f4 f9 26 1e 79 a0 e4 bf
IEEE 802.1X RX: version=1 type=3 length=151
EAPOL-Key type=2
key_info 0x13ca (ver=2 keyidx=0 rsvd=0 Pairwise Install Ack MIC Secure
Encr)
key_length=16 key_data_length=56
replay_counter - hexdump(len=8): 00 00 00 00 00 00 0a 49
key_nonce - hexdump(len=32): bf 66 e9 22 34 9a 54 97 4a d1 f4 0f 68 ea
96 50 bb 75 fd 8f 8d ae 98 95 06 c8 d6 60 fd b7 89 1b
key_iv - hexdump(len=16): 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
key_rsc - hexdump(len=8): 3f e3 04 00 00 00 00 00
key_id (reserved) - hexdump(len=8): 00 00 00 00 00 00 00 00
key_mic - hexdump(len=16): 72 62 5e ad 3f fa de fa a8 df 9c 8b 28 54 ac 52
WPA: RX EAPOL-Key - hexdump(len=155): 01 03 00 97 02 13 ca 00 10 00 00
00 00 00 00 0a 49 bf 66 e9 22 34 9a 54 97 4a d1 f4 0f 68 ea 96 50 bb 75
fd 8f 8d ae 98 95 06 c8 d6 60 fd b7 89 1b 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 3f e3 04 00 00 00 00 00 00 00 00 00 00 00 00 00 72 62
5e ad 3f fa de fa a8 df 9c 8b 28 54 ac 52 00 38 af f7 5a c8 75 be 95 65
97 ce 28 db d4 84 fd 79 db 70 50 31 4e 48 5e 1b dc 04 fa c8 8f 88 ba 1f
e8 55 04 60 a0 f2 a5 84 ca 78 bb de db 39 d3 18 f4 f9 26 1e 79 a0 e4 bf
RSN: encrypted key data - hexdump(len=56): af f7 5a c8 75 be 95 65 97 ce
28 db d4 84 fd 79 db 70 50 31 4e 48 5e 1b dc 04 fa c8 8f 88 ba 1f e8 55
04 60 a0 f2 a5 84 ca 78 bb de db 39 d3 18 f4 f9 26 1e 79 a0 e4 bf
WPA: decrypted EAPOL-Key key data - hexdump(len=48): [REMOVED]
State: 4WAY_HANDSHAKE -> 4WAY_HANDSHAKE
WPA: RX message 3 of 4-Way Handshake from 00:1e:c1:a2:01:5a (ver=2)
WPA: IE KeyData - hexdump(len=48): 30 14 01 00 00 0f ac 04 01 00 00 0f
ac 04 01 00 00 0f ac 02 01 00 dd 16 00 0f ac 01 03 00 9f a8 6b 04 f7 5c
23 20 14 e0 8a bd 0e de 92 10 dd 00
WPA: RSN IE in EAPOL-Key - hexdump(len=22): 30 14 01 00 00 0f ac 04 01
00 00 0f ac 04 01 00 00 0f ac 02 01 00
WPA: GTK in EAPOL-Key - hexdump(len=24): [REMOVED]
WPA: Sending EAPOL-Key 4/4
WPA: TX EAPOL-Key - hexdump(len=99): 01 03 00 5f 02 03 0a 00 00 00 00 00
00 00 00 0a 49 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ca 0c ff
3c 6b 08 dd b6 71 12 6f 83 97 7f 33 4c 00 00
WPA: Installing PTK to the driver.
wpa_driver_nl80211_set_key: ifindex=6 alg=3 addr=0xdc85b0 key_idx=0
set_tx=1 seq_len=6 key_len=16
addr=00:1e:c1:a2:01:5a
EAPOL: External notification - portValid=1
State: 4WAY_HANDSHAKE -> GROUP_HANDSHAKE
RSN: received GTK in pairwise handshake - hexdump(len=18): [REMOVED]
WPA: Group Key - hexdump(len=16): [REMOVED]
WPA: Installing GTK to the driver (keyidx=3 tx=0 len=16).
WPA: RSC - hexdump(len=6): 3f e3 04 00 00 00
wpa_driver_nl80211_set_key: ifindex=6 alg=3 addr=0x450c7b key_idx=3
set_tx=0 seq_len=6 key_len=16
WPA: Key negotiation completed with 00:1e:c1:a2:01:5a [PTK=CCMP GTK=CCMP]
Cancelling authentication timeout
State: GROUP_HANDSHAKE -> COMPLETED
CTRL-EVENT-CONNECTED - Connection to 00:1e:c1:a2:01:5a completed (auth)
[id=0 id_str=]
wpa_driver_nl80211_set_operstate: operstate 0->1 (UP)
netlink: Operstate: linkmode=-1, operstate=6
EAPOL: External notification - portValid=1
EAPOL: External notification - EAP success=1
EAPOL: SUPP_PAE entering state AUTHENTICATING
EAPOL: SUPP_BE entering state SUCCESS
EAP: EAP entering state DISABLED
EAPOL: SUPP_PAE entering state AUTHENTICATED
EAPOL: Supplicant port status: Authorized
EAPOL: SUPP_BE entering state IDLE
EAPOL authentication completed successfully
RTM_NEWLINK: operstate=1 ifi_flags=0x11043 ([UP][RUNNING][LOWER_UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
EAPOL: startWhen --> 0
EAPOL: disable timer tick
CTRL-EVENT-TERMINATING - signal 2 received
Removing interface wlan0
wpa_driver_nl80211_deauthenticate
wpa_driver_nl80211_set_key: ifindex=6 alg=0 addr=0x450c7b key_idx=0
set_tx=0 seq_len=0 key_len=0
wpa_driver_nl80211_set_key: ifindex=6 alg=0 addr=0x450c7b key_idx=1
set_tx=0 seq_len=0 key_len=0
wpa_driver_nl80211_set_key: ifindex=6 alg=0 addr=0x450c7b key_idx=2
set_tx=0 seq_len=0 key_len=0
wpa_driver_nl80211_set_key: ifindex=6 alg=0 addr=0x450c7b key_idx=3
set_tx=0 seq_len=0 key_len=0
wpa_driver_nl80211_set_key: ifindex=6 alg=0 addr=0xdc7a80 key_idx=0
set_tx=0 seq_len=0 key_len=0
addr=00:1e:c1:a2:01:5a
State: COMPLETED -> DISCONNECTED
wpa_driver_nl80211_set_operstate: operstate 1->0 (DORMANT)
netlink: Operstate: linkmode=-1, operstate=5
EAPOL: External notification - portEnabled=0
EAPOL: SUPP_PAE entering state DISCONNECTED
EAPOL: Supplicant port status: Unauthorized
EAPOL: SUPP_BE entering state INITIALIZE
EAPOL: Supplicant port status: Unauthorized
EAPOL: External notification - portValid=0
EAPOL: Supplicant port status: Unauthorized
EAPOL: External notification - EAP success=0
EAPOL: Supplicant port status: Unauthorized
No keys have been configured - skip key clearing
BSS: Remove id 0 BSSID 80:c6:ab:1e:48:d3 SSID 'UPC0038938'
BSS: Remove id 1 BSSID 00:14:7f:c6:a0:bc SSID 'SpeedTouch5E1151'
BSS: Remove id 2 BSSID 00:18:f6:e9:22:07 SSID 'Thomson104ABB'
BSS: Remove id 3 BSSID 00:23:cd:11:e9:c2 SSID 'Sloot'
BSS: Remove id 4 BSSID 00:1e:c1:a2:01:5a SSID 'Perforator'
BSS: Remove id 5 BSSID 00:1e:2a:06:c7:f8 SSID 'NETGEAR'
BSS: Remove id 6 BSSID c0:c1:c0:20:c6:3f SSID 'Cisco36513'
BSS: Remove id 7 BSSID 00:25:9c:df:0a:6d SSID 'Linksys-120n'
Cancelling scan request
Cancelling authentication timeout
netlink: Operstate: linkmode=0, operstate=6
Thanks again!
Stefan Zwanenburg
next prev parent reply other threads:[~2011-09-19 20:05 UTC|newest]
Thread overview: 12+ messages / expand[flat|nested] mbox.gz Atom feed top
[not found] <4E67CE3F.8090405@gmail.com>
[not found] ` <4E67CEA3.7020709@gmail.com>
2011-09-08 1:52 ` RTL8192SE and 802.11n problem Larry Finger
2011-09-08 2:23 ` Larry Finger
2011-09-08 2:50 ` Larry Finger
2011-09-08 3:23 ` Stefan Zwanenburg
2011-09-08 3:42 ` Larry Finger
[not found] ` <8117B559D4E64A83837479A8C342A5CA@realsil.com.cn>
[not found] ` <4E6E537D.5060404@gmail.com>
[not found] ` <24C6797004D84406B7564679CAE21531@realsil.com.cn>
[not found] ` <4E74946A.3080206@gmail.com>
[not found] ` <1903155944F64F00AC0C401593C20923@realsil.com.cn>
2011-09-19 20:04 ` Stefan Zwanenburg [this message]
[not found] <4E77AECF.7090001@gmail.com>
[not found] ` <4E820130.7080801@gmail.com>
2011-09-27 21:00 ` 答复: 答复: 答复: " Larry Finger
2011-09-27 22:25 ` Stefan Zwanenburg
2011-09-28 4:56 ` Larry Finger
2011-09-28 23:28 ` Stefan Zwanenburg
2011-09-29 2:32 ` Stefan Zwanenburg
2011-09-29 3:28 ` Larry Finger
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=4E77A065.4070300@gmail.com \
--to=stefanhetzwaantje@gmail.com \
--cc=Larry.Finger@lwfinger.net \
--cc=chaoming_li@realsil.com.cn \
--cc=linux-wireless@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.