From: Chiefdome <chiefdome@googlemail.com>
To: Larry Finger <Larry.Finger@lwfinger.net>
Cc: george0505@realtek.com, linux-wireless@vger.kernel.org
Subject: Re: Alfa AWUS036NHR with RTL8188RU chipset
Date: Wed, 21 Sep 2011 21:19:44 +0200 [thread overview]
Message-ID: <4E7A38D0.7070304@googlemail.com> (raw)
In-Reply-To: <4E79F87F.1050402@lwfinger.net>
On 09/21/2011 04:45 PM, Larry Finger wrote:
> On 09/21/2011 04:43 AM, Chiefdome wrote:
>> I tried the latest git repo from
>> git://git.infradead.org/users/linville/wireless-next.
>> Same story here.
>> After disconnecting to the network, I have to reload the module only
>> then
>> networks are seen.
>
> I just cloned the wireless-next tree. The two patches mentioned in my
> previous Email are included.
>
> Please run the following command sequence and send us the dmesg output
> after your failure occurs:
>
> modprobe -rv rtl8192cu
> modprobe -v rtlwifi debug=3
> modprobe -v rtl8192cu
>
> Larry
I have found another bug - it is impossible to me to connect a
WPA2-network - here is the dmesg output for that - will send you the
output for a WEP-network later then:
[ 194.011573] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 194.230135] rtl8192cu: MAC auto ON okay!
[ 194.263015] rtl8192cu: Tx queue select: 0x05
[ 194.263820] rtl8192c_common: Loading firmware file
rtlwifi/rtl8192cufw.bin
[ 194.670927] ADDRCONF(NETDEV_UP): wlan1: link is not ready
[ 237.379814] rtl8192cu: MAC auto ON okay!
[ 237.413488] rtl8192cu: Tx queue select: 0x05
[ 237.414243] rtl8192c_common: Loading firmware file
rtlwifi/rtl8192cufw.bin
[ 237.821229] ADDRCONF(NETDEV_UP): wlan1: link is not ready
[ 238.160462] e1000e 0000:00:19.0: irq 45 for MSI/MSI-X
[ 238.220187] e1000e 0000:00:19.0: irq 45 for MSI/MSI-X
[ 238.221641] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 278.340442] usbcore: deregistering interface driver rtl8192cu
[ 326.145824] rtl8192cu:rtl92cu_read_eeprom_info():<0-0> Boot from EFUSE
[ 326.223617] rtl8192cu: MAC address: [MAC-ADDRESS]
[ 326.223629] rtl8192cu:_rtl92cu_read_adapter_info():<0-0> VID = 0xbda
PID = 0x817f
[ 326.223636] rtl8192cu: Board Type 1
[ 326.223641] rtl8192cu:_rtl92cu_hal_customized_behavior():<0-0> RT
Customized ID: 0x00
[ 326.227751] rtlwifi:_rtl_usb_init():<0-0> USB EP(0x81),
MaxPacketSize=512 ,Interval=0.
[ 326.227762] rtlwifi:_rtl_usb_init():<0-0> USB EP(0x02),
MaxPacketSize=512 ,Interval=0.
[ 326.227770] rtlwifi:_rtl_usb_init():<0-0> USB EP(0x03),
MaxPacketSize=512 ,Interval=0.
[ 326.227777] rtlwifi:_rtl_usb_init():<0-0> USB EP(0x84),
MaxPacketSize=64 ,Interval=1.
[ 326.228202] rtl8192cu:_TwoOutEpMapping():<0-0> USB typical Setting.....
[ 326.228209] rtlwifi:_rtl_usb_init_tx():<0-0> USB Max Bulk-out Size=512
[ 326.228217] rtlwifi: rx_max_size 15360, rx_urb_num 8, in_ep 1
[ 326.228223] rtlwifi:_rtl_init_hw_ht_capab():<0-0> 1T1R
[ 326.228234] cfg80211: Updating information on frequency 2412 MHz for
a 20 MHz width channel with regulatory rule:
[ 326.228241] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A
mBi, 2000 mBm)
[ 326.228247] cfg80211: Updating information on frequency 2417 MHz for
a 20 MHz width channel with regulatory rule:
[ 326.228253] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A
mBi, 2000 mBm)
[ 326.228259] cfg80211: Updating information on frequency 2422
MH00:1c:4a:03:b9:64z for a 20 MHz width channel with regulatory rule:
[ 326.228266] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A
mBi, 2000 mBm)
[ 326.228271] cfg80211: Updating information on frequency 2427 MHz for
a 20 MHz width channel with regulatory rule:
[ 326.228278] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A
mBi, 2000 mBm)
[ 326.228284] cfg80211: Updating information on frequency 2432 MHz for
a 20 MHz width channel with regulatory rule:
[ 326.228290] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A
mBi, 2000 mBm)
[ 326.228296] cfg80211: Updating information on frequency 2437 MHz for
a 20 MHz width channel with regulatory rule:
[ 326.228302] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A
mBi, 2000 mBm)
[ 326.228308] cfg80211: Updating information on frequency 2442 MHz for
a 20 MHz width channel with regulatory rule:
[ 326.228314] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A
mBi, 2000 mBm)
[ 326.228320] cfg80211: Updating information on frequency 2447 MHz for
a 20 MHz width channel with regulatory rule:
[ 326.228327] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A
mBi, 2000 mBm)
[ 326.228332] cfg80211: Updating information on frequency 2452 MHz for
a 20 MHz width channel with regulatory rule:
[ 326.228339] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A
mBi, 2000 mBm)
[ 326.228344] cfg80211: Updating information on frequency 2457 MHz for
a 20 MHz width channel with regulatory rule:
[ 326.228351] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A
mBi, 2000 mBm)
[ 326.228356] cfg80211: Updating information on frequency 2462 MHz for
a 20 MHz width channel with regulatory rule:
[ 326.228363] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A
mBi, 2000 mBm)
[ 326.228369] cfg80211: Disabling freq 2467 MHz as custom regd has no
rule that fits a 20 MHz wide channel
[ 326.228374] cfg80211: Disabling freq 2472 MHz as custom regd has no
rule that fits a 20 MHz wide channel
[ 326.228380] cfg80211: Disabling freq 2484 MHz as custom regd has no
rule that fits a 20 MHz wide channel
[ 326.228554] cfg80211: Ignoring regulatory request Set by core since
the driver uses its own custom regulatory domain
[ 326.228881] ieee80211 phy2: Selected rate control algorithm 'rtl_rc'
[ 326.234614] usbcore: registered new interface driver rtl8192cu
[ 330.227015] rtl8192cu:_rtl92cu_init_power_on():<0-0> Autoload Done!
[ 330.228731] rtl8192cu: MAC auto ON okay!
[ 330.264497] rtl8192cu: Tx queue select: 0x05
[ 330.264507] rtl8192cu:rtl92c_set_network_type():<0-0> Set Network
type to NO LINK!
[ 330.265249] rtl8192c_common:rtl92c_phy_set_bw_mode():<0-0> FALSE
driver sleep or unload
[ 330.265265] rtl8192c_common: Loading firmware file
rtlwifi/rtl8192cufw.bin
[ 330.265269] rtl8192c_common:rtl92c_download_fw():<0-0> Firmware
Version(63), Signature(0x88c1),Size(32)
[ 330.658702] rtl8192cu:rtl92cu_set_hw_reg():<0-0> ### Set
RCR(0xf0002a0e) ###
[ 330.658734] rtl8192cu:rtl92cu_set_hw_reg():<0-0> Set
HW_VAR_RETRY_LIMIT(0x00000004)
[ 330.670568] ADDRCONF(NETDEV_UP): wlan1: link is not ready
[ 340.000671] rtl8192cu:rtl92cu_set_hw_reg():<0-0> ### Set
RCR(0xf0002a0e) ###
[ 340.016768] rtl8192cu:_rtl92cu_init_power_on():<0-0> Autoload Done!
[ 340.018500] rtl8192cu: MAC auto ON okay!
[ 340.051808] rtl8192cu: Tx queue select: 0x05
[ 340.051828] rtl8192cu:rtl92c_set_network_type():<0-0> Set Network
type to NO LINK!
[ 340.052543] rtl8192c_common:rtl92c_phy_set_bw_mode():<0-0> FALSE
driver sleep or unload
[ 340.052583] rtl8192c_common: Loading firmware file
rtlwifi/rtl8192cufw.bin
[ 340.052590] rtl8192c_common:rtl92c_download_fw():<0-0> Firmware
Version(63), Signature(0x88c1),Size(32)
[ 340.450345] rtl8192cu:rtl92cu_set_hw_reg():<0-0> ### Set
RCR(0xf0002ace) ###
[ 340.450367] rtl8192cu:rtl92cu_set_hw_reg():<0-0> Set
HW_VAR_RETRY_LIMIT(0x00000004)
[ 340.462324] ADDRCONF(NETDEV_UP): wlan1: link is not ready
[ 340.810935] e1000e 0000:00:19.0: irq 45 for MSI/MSI-X
[ 340.870239] e1000e 0000:00:19.0: irq 45 for MSI/MSI-X
[ 340.871685] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 340.960624] rtl8192cu:rtl92cu_set_hw_reg():<0-0> ### Set
RCR(0xf0002a0e) ###
[ 341.088320] rtl8192cu:_rtl92cu_init_power_on():<0-0> Autoload Done!
[ 341.091812] rtl8192cu: MAC auto ON okay!
[ 341.128338] rtl8192cu: Tx queue select: 0x05
[ 341.128356] rtl8192cu:rtl92c_set_network_type():<0-0> Set Network
type to NO LINK!
[ 341.129072] rtl8192c_common:rtl92c_phy_set_bw_mode():<0-0> FALSE
driver sleep or unload
[ 341.129112] rtl8192c_common: Loading firmware file
rtlwifi/rtl8192cufw.bin
[ 341.129119] rtl8192c_common:rtl92c_download_fw():<0-0> Firmware
Version(63), Signature(0x88c1),Size(32)
[ 341.523259] rtl8192cu:rtl92cu_set_hw_reg():<0-0> ### Set
RCR(0xf0002ace) ###
[ 341.523296] rtl8192cu:rtl92cu_set_hw_reg():<0-0> Set
HW_VAR_RETRY_LIMIT(0x00000004)
[ 341.535132] ADDRCONF(NETDEV_UP): wlan1: link is not ready
[ 344.553546] wlan1: direct probe to [MAC-ADDRESS] (try 1/3)
[ 344.750275] wlan1: direct probe to [MAC-ADDRESS] (try 2/3)
[ 344.950061] wlan1: direct probe to [MAC-ADDRESS] (try 3/3)
[ 345.150150] wlan1: direct probe to [MAC-ADDRESS] timed out
next prev parent reply other threads:[~2011-09-21 19:19 UTC|newest]
Thread overview: 49+ messages / expand[flat|nested] mbox.gz Atom feed top
2011-09-20 2:10 Alfa AWUS036NHR with RTL8188RU chipset Chiefdome
2011-09-20 2:27 ` Chiefdome
2011-09-20 3:05 ` Larry Finger
2011-09-20 9:32 ` Chiefdome
2011-09-20 21:38 ` Chiefdome
2011-09-20 22:32 ` Larry Finger
2011-09-21 0:02 ` Larry Finger
2011-09-21 9:43 ` Chiefdome
2011-09-21 14:45 ` Larry Finger
2011-09-21 19:19 ` Chiefdome [this message]
2011-09-21 20:03 ` Larry Finger
2011-09-21 20:28 ` Chiefdome
2011-09-21 20:37 ` Larry Finger
2011-09-21 20:39 ` Chiefdome
2011-09-21 20:41 ` Chiefdome
2011-09-21 21:09 ` Larry Finger
2011-09-30 14:20 ` v4mp
2011-09-30 15:18 ` Larry Finger
2011-09-30 18:14 ` v4mp
2011-10-06 16:25 ` Toddy
2011-10-06 22:06 ` Larry Finger
2011-10-08 16:24 ` Toddy
2011-10-08 16:52 ` Larry Finger
2011-10-08 23:29 ` Gábor Stefanik
2011-10-09 14:21 ` v4mp
2011-10-09 14:47 ` Larry Finger
2011-10-15 14:22 ` v4mp
2011-10-16 2:49 ` Larry Finger
2011-10-17 10:07 ` v4mp
2011-10-17 14:59 ` Larry Finger
2011-10-17 17:09 ` v4mp
2011-10-17 18:38 ` Larry Finger
2011-10-18 3:23 ` Larry Finger
2011-10-18 12:44 ` v4mp
2011-10-18 13:07 ` v4mp
2011-10-18 15:20 ` Larry Finger
2011-10-18 21:50 ` v4mp
2011-10-18 23:01 ` Larry Finger
2011-10-19 8:17 ` v4mp
2011-10-19 12:08 ` Larry Finger
2011-10-19 14:37 ` v4mp
2011-10-20 3:38 ` Larry Finger
2011-10-20 9:47 ` v4mp
2011-10-20 13:35 ` Larry Finger
2011-10-26 15:49 ` Chiefdome
2011-10-26 16:12 ` Larry Finger
2011-10-26 19:39 ` Chiefdome
2011-10-26 21:20 ` Larry Finger
2011-10-26 21:31 ` Larry Finger
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=4E7A38D0.7070304@googlemail.com \
--to=chiefdome@googlemail.com \
--cc=Larry.Finger@lwfinger.net \
--cc=george0505@realtek.com \
--cc=linux-wireless@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.