From: Chiefdome <chiefdome@googlemail.com>
To: Larry Finger <Larry.Finger@lwfinger.net>
Cc: george0505@realtek.com, linux-wireless@vger.kernel.org
Subject: Re: Alfa AWUS036NHR with RTL8188RU chipset
Date: Wed, 21 Sep 2011 22:28:01 +0200 [thread overview]
Message-ID: <4E7A48D1.8050009@googlemail.com> (raw)
In-Reply-To: <4E7A4310.30106@lwfinger.net>
On 09/21/2011 10:03 PM, Larry Finger wrote:
> On 09/21/2011 02:19 PM, Chiefdome wrote:
>> I have found another bug - it is impossible to me to connect a
>> WPA2-network -
>> here is the dmesg output for that - will send you the output for a
>> WEP-network
>> later then:
>>
>> [ 194.011573] ADDRCONF(NETDEV_UP): eth0: link is not ready
>> [ 194.230135] rtl8192cu: MAC auto ON okay!
>> [ 194.263015] rtl8192cu: Tx queue select: 0x05
>> [ 194.263820] rtl8192c_common: Loading firmware file
>> rtlwifi/rtl8192cufw.bin
>> [ 194.670927] ADDRCONF(NETDEV_UP): wlan1: link is not ready
>> [ 237.379814] rtl8192cu: MAC auto ON okay!
>> [ 237.413488] rtl8192cu: Tx queue select: 0x05
>> [ 237.414243] rtl8192c_common: Loading firmware file
>> rtlwifi/rtl8192cufw.bin
>> [ 237.821229] ADDRCONF(NETDEV_UP): wlan1: link is not ready
>> [ 238.160462] e1000e 0000:00:19.0: irq 45 for MSI/MSI-X
>> [ 238.220187] e1000e 0000:00:19.0: irq 45 for MSI/MSI-X
>> [ 238.221641] ADDRCONF(NETDEV_UP): eth0: link is not ready
>> [ 278.340442] usbcore: deregistering interface driver rtl8192cu
>> [ 326.145824] rtl8192cu:rtl92cu_read_eeprom_info():<0-0> Boot from EFUSE
>> [ 326.223617] rtl8192cu: MAC address: [MAC-ADDRESS]
>> [ 326.223629] rtl8192cu:_rtl92cu_read_adapter_info():<0-0> VID =
>> 0xbda PID = 0x817f
>> [ 326.223636] rtl8192cu: Board Type 1
>> [ 326.223641] rtl8192cu:_rtl92cu_hal_customized_behavior():<0-0> RT
>> Customized
>> ID: 0x00
>> [ 326.227751] rtlwifi:_rtl_usb_init():<0-0> USB EP(0x81),
>> MaxPacketSize=512
>> ,Interval=0.
>> [ 326.227762] rtlwifi:_rtl_usb_init():<0-0> USB EP(0x02),
>> MaxPacketSize=512
>> ,Interval=0.
>> [ 326.227770] rtlwifi:_rtl_usb_init():<0-0> USB EP(0x03),
>> MaxPacketSize=512
>> ,Interval=0.
>> [ 326.227777] rtlwifi:_rtl_usb_init():<0-0> USB EP(0x84),
>> MaxPacketSize=64
>> ,Interval=1.
>> [ 326.228202] rtl8192cu:_TwoOutEpMapping():<0-0> USB typical
>> Setting.....
>> [ 326.228209] rtlwifi:_rtl_usb_init_tx():<0-0> USB Max Bulk-out Size=512
>> [ 326.228217] rtlwifi: rx_max_size 15360, rx_urb_num 8, in_ep 1
>> [ 326.228223] rtlwifi:_rtl_init_hw_ht_capab():<0-0> 1T1R
>> [ 326.228234] cfg80211: Updating information on frequency 2412 MHz
>> for a 20 MHz
>> width channel with regulatory rule:
>> [ 326.228241] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A
>> mBi, 2000 mBm)
>> [ 326.228247] cfg80211: Updating information on frequency 2417 MHz
>> for a 20 MHz
>> width channel with regulatory rule:
>> [ 326.228253] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A
>> mBi, 2000 mBm)
>> [ 326.228259] cfg80211: Updating information on frequency 2422
>> MH00:1c:4a:03:b9:64z for a 20 MHz width channel with regulatory rule:
>> [ 326.228266] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A
>> mBi, 2000 mBm)
>> [ 326.228271] cfg80211: Updating information on frequency 2427 MHz
>> for a 20 MHz
>> width channel with regulatory rule:
>> [ 326.228278] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A
>> mBi, 2000 mBm)
>> [ 326.228284] cfg80211: Updating information on frequency 2432 MHz
>> for a 20 MHz
>> width channel with regulatory rule:
>> [ 326.228290] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A
>> mBi, 2000 mBm)
>> [ 326.228296] cfg80211: Updating information on frequency 2437 MHz
>> for a 20 MHz
>> width channel with regulatory rule:
>> [ 326.228302] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A
>> mBi, 2000 mBm)
>> [ 326.228308] cfg80211: Updating information on frequency 2442 MHz
>> for a 20 MHz
>> width channel with regulatory rule:
>> [ 326.228314] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A
>> mBi, 2000 mBm)
>> [ 326.228320] cfg80211: Updating information on frequency 2447 MHz
>> for a 20 MHz
>> width channel with regulatory rule:
>> [ 326.228327] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A
>> mBi, 2000 mBm)
>> [ 326.228332] cfg80211: Updating information on frequency 2452 MHz
>> for a 20 MHz
>> width channel with regulatory rule:
>> [ 326.228339] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A
>> mBi, 2000 mBm)
>> [ 326.228344] cfg80211: Updating information on frequency 2457 MHz
>> for a 20 MHz
>> width channel with regulatory rule:
>> [ 326.228351] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A
>> mBi, 2000 mBm)
>> [ 326.228356] cfg80211: Updating information on frequency 2462 MHz
>> for a 20 MHz
>> width channel with regulatory rule:
>> [ 326.228363] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A
>> mBi, 2000 mBm)
>> [ 326.228369] cfg80211: Disabling freq 2467 MHz as custom regd has no
>> rule that
>> fits a 20 MHz wide channel
>> [ 326.228374] cfg80211: Disabling freq 2472 MHz as custom regd has no
>> rule that
>> fits a 20 MHz wide channel
>> [ 326.228380] cfg80211: Disabling freq 2484 MHz as custom regd has no
>> rule that
>> fits a 20 MHz wide channel
>> [ 326.228554] cfg80211: Ignoring regulatory request Set by core since
>> the driver
>> uses its own custom regulatory domain
>> [ 326.228881] ieee80211 phy2: Selected rate control algorithm 'rtl_rc'
>> [ 326.234614] usbcore: registered new interface driver rtl8192cu
>> [ 330.227015] rtl8192cu:_rtl92cu_init_power_on():<0-0> Autoload Done!
>> [ 330.228731] rtl8192cu: MAC auto ON okay!
>> [ 330.264497] rtl8192cu: Tx queue select: 0x05
>> [ 330.264507] rtl8192cu:rtl92c_set_network_type():<0-0> Set Network
>> type to NO
>> LINK!
>> [ 330.265249] rtl8192c_common:rtl92c_phy_set_bw_mode():<0-0> FALSE
>> driver sleep
>> or unload
>> [ 330.265265] rtl8192c_common: Loading firmware file
>> rtlwifi/rtl8192cufw.bin
>> [ 330.265269] rtl8192c_common:rtl92c_download_fw():<0-0> Firmware
>> Version(63),
>> Signature(0x88c1),Size(32)
>> [ 330.658702] rtl8192cu:rtl92cu_set_hw_reg():<0-0> ### Set
>> RCR(0xf0002a0e) ###
>> [ 330.658734] rtl8192cu:rtl92cu_set_hw_reg():<0-0> Set
>> HW_VAR_RETRY_LIMIT(0x00000004)
>> [ 330.670568] ADDRCONF(NETDEV_UP): wlan1: link is not ready
>> [ 340.000671] rtl8192cu:rtl92cu_set_hw_reg():<0-0> ### Set
>> RCR(0xf0002a0e) ###
>> [ 340.016768] rtl8192cu:_rtl92cu_init_power_on():<0-0> Autoload Done!
>> [ 340.018500] rtl8192cu: MAC auto ON okay!
>> [ 340.051808] rtl8192cu: Tx queue select: 0x05
>> [ 340.051828] rtl8192cu:rtl92c_set_network_type():<0-0> Set Network
>> type to NO
>> LINK!
>> [ 340.052543] rtl8192c_common:rtl92c_phy_set_bw_mode():<0-0> FALSE
>> driver sleep
>> or unload
>> [ 340.052583] rtl8192c_common: Loading firmware file
>> rtlwifi/rtl8192cufw.bin
>> [ 340.052590] rtl8192c_common:rtl92c_download_fw():<0-0> Firmware
>> Version(63),
>> Signature(0x88c1),Size(32)
>> [ 340.450345] rtl8192cu:rtl92cu_set_hw_reg():<0-0> ### Set
>> RCR(0xf0002ace) ###
>> [ 340.450367] rtl8192cu:rtl92cu_set_hw_reg():<0-0> Set
>> HW_VAR_RETRY_LIMIT(0x00000004)
>> [ 340.462324] ADDRCONF(NETDEV_UP): wlan1: link is not ready
>> [ 340.810935] e1000e 0000:00:19.0: irq 45 for MSI/MSI-X
>> [ 340.870239] e1000e 0000:00:19.0: irq 45 for MSI/MSI-X
>> [ 340.871685] ADDRCONF(NETDEV_UP): eth0: link is not ready
>> [ 340.960624] rtl8192cu:rtl92cu_set_hw_reg():<0-0> ### Set
>> RCR(0xf0002a0e) ###
>> [ 341.088320] rtl8192cu:_rtl92cu_init_power_on():<0-0> Autoload Done!
>> [ 341.091812] rtl8192cu: MAC auto ON okay!
>> [ 341.128338] rtl8192cu: Tx queue select: 0x05
>> [ 341.128356] rtl8192cu:rtl92c_set_network_type():<0-0> Set Network
>> type to NO
>> LINK!
>> [ 341.129072] rtl8192c_common:rtl92c_phy_set_bw_mode():<0-0> FALSE
>> driver sleep
>> or unload
>> [ 341.129112] rtl8192c_common: Loading firmware file
>> rtlwifi/rtl8192cufw.bin
>> [ 341.129119] rtl8192c_common:rtl92c_download_fw():<0-0> Firmware
>> Version(63),
>> Signature(0x88c1),Size(32)
>> [ 341.523259] rtl8192cu:rtl92cu_set_hw_reg():<0-0> ### Set
>> RCR(0xf0002ace) ###
>> [ 341.523296] rtl8192cu:rtl92cu_set_hw_reg():<0-0> Set
>> HW_VAR_RETRY_LIMIT(0x00000004)
>> [ 341.535132] ADDRCONF(NETDEV_UP): wlan1: link is not ready
>> [ 344.553546] wlan1: direct probe to [MAC-ADDRESS] (try 1/3)
>> [ 344.750275] wlan1: direct probe to [MAC-ADDRESS] (try 2/3)
>> [ 344.950061] wlan1: direct probe to [MAC-ADDRESS] (try 3/3)
>> [ 345.150150] wlan1: direct probe to [MAC-ADDRESS] timed out
>
> The first thing I notice is that you apparently do not have CRDA
> installed. A second thing is that the interface never comes up. As
> long as it remains down, it can never connect. How are you connecting?
> I'm using NetworkManager.
>
> The following is an excerpt from my dmesg log with debug=3 set when
> rtlwifi is loaded:
>
> [17268.232826] usbcore: registered new interface driver rtl8192cu
> [17268.352125] rtl8192cu:_rtl92cu_init_power_on():<0-0> Autoload Done!
> [17268.364205] rtl8192cu: MAC auto ON okay!
> [17269.148482] rtl8192cu: Tx queue select: 0x05
> [17269.149472] rtl8192cu:rtl92c_set_network_type():<0-0> Set Network
> type to NO LINK!
> [17269.159549] rtl8192c_common:rtl92c_phy_set_bw_mode():<0-0> FALSE
> driver sleep or unload
> [17269.161148] rtl8192c_common: Loading firmware file
> rtlwifi/rtl8192cufw.bin
> [17269.161177] rtl8192c_common:rtl92c_download_fw():<0-0> Firmware
> Version(63), Signature(0x88c1),Size(32)
> [17270.343392] rtl8192cu:rtl92cu_set_hw_reg():<0-0> ### Set
> RCR(0xf0002a0e) ###
> [17270.345208] rtl8192cu:rtl92cu_set_hw_reg():<0-0> Set
> HW_VAR_RETRY_LIMIT(0x00000004)
> [17270.388005] ADDRCONF(NETDEV_UP): wlan0: link is not ready
> [17274.168628] wlan0: authenticate with c0:3f:0e:be:2b:44 (try 1)
> [17274.168756] rtlwifi:_rtl_usb_tx_preprocess():<200-1> MAC80211_LINKING
> [17274.173393] wlan0: authenticated
> [17274.259600] wlan0: associate with c0:3f:0e:be:2b:44 (try 1)
> [17274.267367] wlan0: RX AssocResp from c0:3f:0e:be:2b:44 (capab=0x411
> status=0 aid=1)
> [17274.267400] wlan0: associated
> [17274.267428] rtlwifi:rtl_op_sta_add():<0-0> Add sta addr is
> c0:3f:0e:be:2b:44
> [17274.267614] rtl8192cu:rtl92cu_update_hal_rate_table():<0-0> 0
> [17274.274103] rtlwifi:rtl_action_proc():<10000-1> Rx ACT_ADDBAREQ
> From :c0:3f:0e:be:2b:44
> [17274.322888] rtlwifi:rtl_op_bss_info_changed():<0-0> BSS_CHANGED_ASSOC
> [17274.325839] rtlwifi:rtl_op_bss_info_changed():<0-0> c0:3f:0e:be:2b:44
> [17274.336522] rtl8192cu:rtl92cu_set_hw_reg():<0-0> ### Set
> RCR(0xf0002ace) ###
> [17274.340812] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
> [17274.340968] rtlwifi:rtl_action_proc():<200-1> Tx ACT_ADDBARSP From
> :00:1f:1f:c8:8e:cb
> [17274.358740] rtlwifi:rtl_op_set_key():<0-0> Using hardware based
> encryption for keyidx: 0, mac: c0:3f:0e:be:2b:44
> [17274.358799] rtlwifi:rtl_op_set_key():<0-0> alg:CCMP
> [17274.358818] rtlwifi:rtl_op_set_key():<0-0> set enable_hw_sec,
> key_type:4(OPEN:0 WEP40:1 TKIP:2 AES:4 WEP104:5)
> [17274.359178] rtlwifi:rtl_op_set_key():<0-0> set pairwise key
> [17274.359202] rtl8192cu:rtl92c_set_key():<0-0> add one entry
> [17274.359222] rtl8192cu:rtl92c_set_key():<0-0> set Pairwiase key
> [17274.359244] rtlwifi:rtl_cam_add_one_entry():<0-0> EntryNo:4,
> ulKeyId=0, ulEncAlg=4, ulUseDK=0 MacAddr c0:3f:0e:be:2b:44
> [17274.364992] rtlwifi:rtl_cam_add_one_entry():<0-0> <===
> [17274.367387] rtlwifi:rtl_op_set_key():<0-0> Using hardware based
> encryption for keyidx: 1, mac: ff:ff:ff:ff:ff:ff
> [17274.367434] rtlwifi:rtl_op_set_key():<0-0> alg:CCMP
> [17274.367457] rtlwifi:rtl_op_set_key():<0-0> set group key
> [17274.367483] rtl8192cu:rtl92c_set_key():<0-0> add one entry
> [17274.367506] rtl8192cu:rtl92c_set_key():<0-0> set group key
> [17274.367529] rtlwifi:rtl_cam_add_one_entry():<0-0> EntryNo:1,
> ulKeyId=1, ulEncAlg=4, ulUseDK=0 MacAddr ff:ff:ff:ff:ff:ff
> [17274.372787] rtlwifi:rtl_cam_add_one_entry():<0-0> <===
> [17274.416690] rtl8192cu:rtl92cu_update_hal_rate_table():<0-0> 15
> [17276.428211] rtl8192cu:rtl92cu_update_hal_rate_table():<0-0> 15
> [17280.412251] rtl8192cu:rtl92cu_update_hal_rate_table():<0-0> 15
> [17293.203904] rtl8192cu:rtl92cu_set_hw_reg():<0-0> ### Set
> RCR(0xf0002a0e) ###
> [17295.692077] rtlwifi:rtl_tx_agg_start():<0-0> on ra =
> c0:3f:0e:be:2b:44 tid = 0 seq:0
> [17295.692345] rtlwifi:rtl_action_proc():<200-1> Tx ACT_ADDBAREQ From
> :00:1f:1f:c8:8e:cb
> [17295.695093] rtlwifi:rtl_action_proc():<10000-1> Rx ACT_ADDBARSP
> From :c0:3f:0e:be:2b:44
> [17295.695400] rtlwifi:rtl_tx_agg_oper():<0-0> on ra =
> c0:3f:0e:be:2b:44 tid = 0
>
> As you notice, this connection uses the CCMP algorithm, i.e. it is
> with WPA2-AES. It is also an 802.11n. Just to test, I switched the AP
> to run only at 802.11g rates. That also worked.
>
> I need to know more about your setup. What AP and how is it
> configured? How do you control the wireless connection?
>
> Larry
The AP showen above is configured as you say as an 802.11bgn device. The
wireless connection is controlled by wicd.
Chiefdome
next prev parent reply other threads:[~2011-09-21 20:28 UTC|newest]
Thread overview: 49+ messages / expand[flat|nested] mbox.gz Atom feed top
2011-09-20 2:10 Alfa AWUS036NHR with RTL8188RU chipset Chiefdome
2011-09-20 2:27 ` Chiefdome
2011-09-20 3:05 ` Larry Finger
2011-09-20 9:32 ` Chiefdome
2011-09-20 21:38 ` Chiefdome
2011-09-20 22:32 ` Larry Finger
2011-09-21 0:02 ` Larry Finger
2011-09-21 9:43 ` Chiefdome
2011-09-21 14:45 ` Larry Finger
2011-09-21 19:19 ` Chiefdome
2011-09-21 20:03 ` Larry Finger
2011-09-21 20:28 ` Chiefdome [this message]
2011-09-21 20:37 ` Larry Finger
2011-09-21 20:39 ` Chiefdome
2011-09-21 20:41 ` Chiefdome
2011-09-21 21:09 ` Larry Finger
2011-09-30 14:20 ` v4mp
2011-09-30 15:18 ` Larry Finger
2011-09-30 18:14 ` v4mp
2011-10-06 16:25 ` Toddy
2011-10-06 22:06 ` Larry Finger
2011-10-08 16:24 ` Toddy
2011-10-08 16:52 ` Larry Finger
2011-10-08 23:29 ` Gábor Stefanik
2011-10-09 14:21 ` v4mp
2011-10-09 14:47 ` Larry Finger
2011-10-15 14:22 ` v4mp
2011-10-16 2:49 ` Larry Finger
2011-10-17 10:07 ` v4mp
2011-10-17 14:59 ` Larry Finger
2011-10-17 17:09 ` v4mp
2011-10-17 18:38 ` Larry Finger
2011-10-18 3:23 ` Larry Finger
2011-10-18 12:44 ` v4mp
2011-10-18 13:07 ` v4mp
2011-10-18 15:20 ` Larry Finger
2011-10-18 21:50 ` v4mp
2011-10-18 23:01 ` Larry Finger
2011-10-19 8:17 ` v4mp
2011-10-19 12:08 ` Larry Finger
2011-10-19 14:37 ` v4mp
2011-10-20 3:38 ` Larry Finger
2011-10-20 9:47 ` v4mp
2011-10-20 13:35 ` Larry Finger
2011-10-26 15:49 ` Chiefdome
2011-10-26 16:12 ` Larry Finger
2011-10-26 19:39 ` Chiefdome
2011-10-26 21:20 ` Larry Finger
2011-10-26 21:31 ` Larry Finger
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=4E7A48D1.8050009@googlemail.com \
--to=chiefdome@googlemail.com \
--cc=Larry.Finger@lwfinger.net \
--cc=george0505@realtek.com \
--cc=linux-wireless@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.